Search Documents

By Yushuai Xian, Youjun Tao, Fangyuan Ma

This study compared particle size distribution and density distribution of crushed products for waste printed circuit boards (WPCBs) before and after heat treatment. The crushing process for heat-treated WPCBs is a selective crushing process; more metal is concentrated in the coarse particle range of 1.0–0.5 mm and high density range of 2.8–2.96 g/cm3. WPCBs were separated using the Falcon separator to recycle useful metals. The Box-Behnken module of Design-Expert was used to obtain optimal separation parameters, namely, rotational frequency of 25 Hz, recoil water pressure of 0.025 Mpa and feed speed of 34 ml/s. On this basis, the separation indexes for WPCBs with and without heat treatment were compared. Experimental results show that the recovery effect is better for heat-treatedWPCBs than for thosewithout heat treatment. Comparedwith the non-heattreatedWPCBs, the product grade of heat-treated WPCBs is 1.95% higher, and its recovery is improved by about 14%. Finally, characteristics ofWPCBs before and after heat treatment were analyzed on the basis of stress experiments and scanning electron microscopy (SEM), respectively. Results of mechanical characterization indicate that the stress experiment for non-heat-treated WPCBs has a maximumpressure load of 212 N and displacement of 20mm, but heat-treatedWPCBs only need 140 N stress and 14 mm displacement. SEM shows that copper foil and fiberglass cloth are deformed in different directions and sizes after heat treatment to form gaps, which promote liberation of copper foil and fiberglass cloth.

Sep 10, 2020

By O. H. Rostad

The importance of geology in ore reserve estimation has been stated by several authors. King et, a1 (1982) reported that the geological factor was the key deficiency where serious weaknesses in ore reserve estimation appeared, especially in grade. The foundation for a successful mining operation is an ore reserve estimate that neither overstates nor understates the true situation as to tonnage and grade. Overestimation of reserves can have devastating economic results. Overestimation of tonnage may lead to wasting money on an overbuilt plant or worse yet, if grade is seriously overestimated also, to undertaking an operation that is doomed to economic failure from the outset. Understated ore reserves can result in building a plant that is smaller than optimum which may result in higher unit costs. At worst, understated tonnage of ore reserves can result in a missed opportunity for a profitable operation. Failure of the ore reserve estimator to properly take into account all geologic and allied factors pertaining to the deposit can result in an ore reserve estimate that is overstated either as to tonnage or grade or both. This paper will focus on these factors and will not discuss rules about distances above or below a drift that should be given a classification of proven or probable, etc. Each deposit has its own particular characteristics which often require modification of general rules for defining limits of proven and probable ore blocks that work satisfactorily in another deposit. A number of references are included which discuss some of these problems. Definitions of ore reserve classifications and an illustration are given in the Appendix.

Jan 1, 1985

By L. Zhou, L. Yuan, D. Bahrami

Underground mine fires remain a concern for mine operators, posing a health and safety risk to mineworkers. In the last decade, the number of mine fires has decreased significantly; however, dealing with an unknown fire in underground mines can be a challenging task, which could lead to a hazardous condition for miners during an evacuation and rescue operation. A timely detection of a mine fire and monitoring its characteristics, namely size and location, are of great importance in reducing the risk of mine fire injuries. A new improved fire location algorithm has been developed and integrated into an Atmospheric Monitoring System (AMS) program by researchers from the National Institute for Occupational Safety and Health (NIOSH). This paper describes the new fire location model and presents the results of verification fire tests conducted at the Safety Research Coal Mine (SRCM) facility of the Pittsburgh Mining Research Division (PMRD) using the collected AMS data. NIOSH is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions in mines. The results demonstrate successful application of the improved fire location model and provide a useful tool for solving the problem of unknown fire location and reducing the risk of hazardous conditions.

Sep 29, 2020

By B. Li

"The spontaneous combustion of coal storage pile(Gangue Hill) is one of the seriously threat encountered in coal mining and storage. The dynamic accumulation of internal heat in coal storage pile(Gangue Hill) provides continuous heat-source for coal spontaneous combustion. Combined with the features and characteristics of coal pile storage, a technology of heat pipe(HP) is applied to enhance heat transfer. In order to prevent spontaneous combustion of coal storage piles (hillock) due to regeneration, a method using heat pipes to destroy the heat preservation conditions of coal storage pile(Gangue Hill) is proposed, which reduces the risk of coal spontaneous combustion and prevents coal fire. A theoretical model of Coal-Thermosyphon has set up to analysis the radius of cooling effect area quantitatively. An experimental equipment of the heat transferring in a set of heat pipe, which used to study the influence on coal pile temperature distribution, has been designed. Results show, the heat pipe has a significant effect on inhibiting the coal spontaneous combustion process by destroy the heat preservation conditions of the coal. Under the experimental conditions, the most obvious coal temperature decline appears at radius 20.0mm around the pipe, dropped from 45.8? to 32.5?, a decline of 29%; the coal pile temperature at radius 420mm from 12.9? to 12.4?, a decline of 3.87%. And the research offers an effective and new approach in its application and promotion for preventing and controlling in coal spontaneous combustion.INTRODUCTION China is one of a few countries which utilize coal as the major source of energy in the world, and is the one whose characteristic of energy structure is rich coal, deficient oil and lean gas. Relatively speaking, China is abundance in mineral resources. The coal, which is the fundamental resource in the process of industrialization, is the main energy in china. Thus China cannot alter the situation of coal consumption dominated a leading role in its energy structure in near term.A massive of coal gangue would be produced every year in China with the mining activities. And it’s estimated that almost 360 million tons gangue were dumped in 2003, accounting for 10 percent of the whole coal production. Huge numbers of coal waste piles have more than 2,600 seats, which cover an area of over 12,000 hectares. Worse more, the coal gangue still has an annual growth rate of 100 million tons. Toxic smokes and greenhouse gases are discharged directly and prolongly into the atmosphere due to coal gangue spontaneous combustion. Even worse, waste dump explosion cause massive losses and are able to endanger the safety of workers. For example, one waste dump of the NO.4 Mine of Pingdingshan Coal Group Co., Ltd. occurred twice of explosions in 2005, and about 3.13 million tons of waste rocks were thrown within the range from 100 to 300 meters, eight people were killed and 122 rescuers and miners were burned, and economic losses were estimated more than 3,000 million."

Jan 1, 2015

By J. K. Pandey, ebashish Mishra, D. P. Mishra, N. K. Mohalik, S. K. Ray

The increasing demand for coal and depletion of shallow depth reserves are pushing towards deeper mining. In deeper coal mines with multiseam workings, the problem of ventilation surges many folds primarily related to air quantity requirement, heat, humidity and spontaneous heating/fire in goaved (gobbed) out areas. The paper describes the design of a new approach to improve the ventilation system of a real-life deep underground coal mine with multiseam workings. For this, the ventilation problem of one deep underground coal mine 6&7 pits Bhutgoria Amalgamated Colliery of Tata Steel Ltd. with multiseam workings has been studied in detail to determine an appropriate solution. A ventilation survey of the mine and computer simulation of the ventilation network has been carried out to reach a practical solution. Ventilation survey results have been analysed to develop a representative ventilation network of the mine for both qualitative and quantitative analysis. Further, computer simulation of the ventilation network of the mine has been performed to virtually verify the application of a highcapacity booster fan in the present ventilation circuit without disturbing the vulnerable areas. Field validation is also carried out after the implementation of the solution in the mine to determine its efficacy. Thus, the findings of this paper can be directly applied for the installation of booster fans to achieve the required air quantity in deep underground coal mines with multiseam workings having spontaneous combustion liabilities of upper seam goaved out areas.

Jun 2, 2022

Machine breakdowns and maintenance delays are large contributors to lost production and increased operating costs in the mining industry. The U.S. Bureau of Mines is investigating the applications of expert system technology to diagnostic and predictive maintenance tor mining equipment. This will help increase mining productivity and decrease operating costs, by reducing the frequency of equipment failures and repair times. The Bureau has begun this effort by applying expert system techniques to the diagnosis of hydraulic system problems on a continuous mining machine. This paper discusses the development of the hydraulic diagnostic expert system.

Jan 1, 1990

By Ihsan Berk Tulu, Haochen Zhao, Deniz Tuncay

This paper proposes a new method to estimate the percentage of load carried by the gob in underground coal mines using a new parameter that introduces the site-specific overburden geology. The new parameter was defined as the total strong layer thickness (tstr) that represents the strength and stiffness of the overburden with a single value. Twelve field measurement case studies from 11 different U.S. longwall mines with different overburden geologies were used to develop the new methodology. 2D numerical models of these case studies (and additional parametric runs with different panel widths) were verified against field measurements such as surface subsidence and stress. Statistical analyses using the model results were conducted for a loading model with the new tstr parameter as one of the variables. The new methodology was found to have a coefficient of determination (R2) of 85% when compared to the field measurements and the parametric models. The method was then tested for practical implementation for pillar design. The percentages of load carried by the gob as estimated by the new method were implemented into the LaModel program, that is commonly used in the coal industry. The results obtained from LaModel were compared to the available field stress measurements, and the new method implemented into LaModel was found to give successful results.

Jul 18, 2022

By Richard E. Otoo, Evan J. Owen, Virginia T. McLemore

Disruption in critical minerals supply chains has resulted in the evaluation of various types of mineral deposits for critical minerals potential. Much of the study on critical minerals focuses on occurrence and characterization, but little research has addressed what concentrations of critical minerals in a mineral deposit are required to make an exploration target into an operating mine. Understanding the cut-off grades of ore deposits being actively mined is one criterion to determine if concentrations in an exploration target are high enough. Cut-off grade is defined as the minimum amount of mineral contained in a ton of ore that is sent to the processing plant. Among many factors, cut-off grade depends upon the size and type of the deposit and mining operation, the processing technique, and market prices. This research does not aim to define cut-offs for determining if a mineral deposit is economic. Rather, it defines estimates of concentrations of critical minerals that could be considered good enough for further exploration. For example, ~2% total rare earth oxide (TREO) is the cut-off grade for Mt. Pass carbonatite, but 500 ppm TREO could be an exploration target for coals.

Feb 1, 2025

By Molood Saeedi, Nima Sadeghi, Eskandar Keshavarz Alamdari

This study showed the kinetics of gold chlorination leaching from an anode slime complex containing copper, silver, barium, selenium, and tellurium. AgCl and BaSO4 control the rate of gold leaching, and the interface transfer and diffusion across the product was selected as the desirable kinetic model. The concentration of hydrochloric acid, chlorine gas flow rate, pulp density, and temperature have been precisely studied. The results showed that temperature and hydrochloric acid have a favorable influence on the leaching rate. However, the chlorine gas flow rate is inactive in the reaction rate. Furthermore, the leaching rate decreased with an increasing pulp density. The leaching process was controlled by the interface transfer and diffusion across the product, and the activation energy was determined to be 13.66 kJ mol–1.

Oct 19, 2021

By J. J. Komadina

Since the advent of resin-in-pulp (RIP) technology for treatment of uranium-bearing ores in the 1950?s to current carbon-in-pulp (CIP) processing of gold values, metallurgies and operators alike have wrestled with the problem of interstage screening. Early gold CIP plants such as at Homestake utilized externally mounted vibrating screens in conjunction with air lifts to effect carbon-pulp disengagement. Other operations world-wide have likewise adopted this technique with varying degrees of success. Subsequent development of in-tank launder screens both in South Africa and the United States have been of the air cleaned variety (EPAC)

Jan 1, 1988

By C. West

Structured or embossed HDPE and LLDPE geomembranes have been available to mine owners and designers for over ten (10) years. As many owners and designers discover and demand the consistent high quality characteristics of this type of geomembrane due to the unique manufacturing process, the use of these materials in new mines, mine expansions and final closure designs has steadily increased. Structured liner materials are available for double lined and final cover systems and are revolutionizing the way ponds, pads and final closures are constructed. This paper will discuss the structured or embossed geomembrane concept and manufacturing process. Additionally, the paper will present comparative testing illustrating the major advantages of using this type of product in these types of applications. Both technical and economic advantages are illustrated. The cost savings include lower installation costs, less material used, and third party inspection times not to mention better performance. These new systems will be presented.

Jan 1, 2011

By D. W. Scott, D. G. Minnes

Introduction Ontario's diverse industrial mineral resource base includes structural minerals such as sand and gravel, crushed stone, building stone, clay, shale, limestone, and dolostone. These resources are used to produce aggregates, brick, metallurgical stone, fillers, cement, lime, and other construction materials. The majority of the operations are in deposits of Palezoic and Quaternary age in southern Ontario, close to the major markets. Province-wide, there were more than 140 Mt (154 million st) of aggregates produced in 1985. About 115 Mt (128 million st) of that was produced in southern Ontario with the rest being largely from Crown land in northern Ontario. Structural industrial minerals account for more than 80% of the value of total industrial mineral production. The remaining 20% is accounted for by the nonstructural minerals, such as salt, which is produced in the southwestern part of the province. A host of other nonstructural industrial minerals are known. Production, though, is currently restricted to calcite, gypsum, quartz, talc, nepheline syenite, and byproduct metallurgical sulfur products (Fig. 1). Major production is close to the large markets of urbanized southern Ontario and the northeastern and northcentral US. With an abundant variety of industrial mineral resources and the large population within 650 km (400 miles) of most deposits, the market offers great potential. Ontario's nine million people accounted for about 35% of Canada's entire $476.3 billion gross domestic product in 1985. This equates to about one-third of the nation's buying power being within a 200-km (125-mile) radius of Toronto. This major concentration of industrial and economic activity has resulted in a well-developed industrial minerals industry that fulfills most of the structural industrial minerals demand in Ontario. Nonstructural industrial minerals are similarly well placed to compete in this high demand area. Although Ontario manufacturers still import some of these materials, Ontario products are achieving significant market share. And, they serve the needs of neighboring provinces and states. Present production and trends Ontario has traditionally produced significant amounts of industrial minerals. This produc¬tion had a value of $956 million in 1984 (Table 1). Structural materials production in 1985 and 1986 approached or exceeded levels not seen since the early 1970s. Many new products have been developed using these raw materials. The industry is becoming concentrated in the hands of several large companies, mainly four large cement com-

Jan 12, 1987

By D. Blackwell, W. R. Reed, G. Ross, S. Peters, M. Shahan

Dust collectors for roof bolting machines generally use a dry box to collect the roof bolting material. Recently, an underground mining operation converted a dry box dust collector to a wet box dust collector with a unique exception from MSHA for testing purposes.Water is routed to the roof bolter fromthe main water line of the continuous miner. The wet box utilizes a water spray to wet the incoming material. Testing was conducted comparing the two different collector types. Respirable dust concentrations surrounding the roof bolter with the different collection boxes were similar. The main difference in respirable dust concentrations occurred when cleaning the dust boxes. The average respirable dust concentration during cleaning of the wet box was 0.475 mg/ m3, and during the cleaning of the dry box, the average respirable dust concentration was 1.188 mg/m3, a 60% reduction in respirable dust concentration. The quartz content of the roofmaterialwas high, ranging from 28.9 to 52.7%during this study. The results from this study indicate that using the wet box as a collector reduced exposure to respirable dust up to 60% when cleaning the collector boxes.

Aug 26, 2020

By Veerendra Singh, NILAMADHABA SAHU, ARIJIT BISWAS

Manganese (Mn) ferroalloys are chiefly consumed in the steelmaking process as a deoxidizing agent or as an alloying element to produce high-quality steels. These alloys are typically produced in a submerged arc furnace using coke, fluxes and manganese ores of a specific manganese/Fe (Mn/Fe) ratio. Preferred-grade manganese ores should have Mn content greater than 46 percent and Mn/Fe content greater than 5 to produce commercial-grade, high-carbon ferromanganese [1]. Selective mining of high-grade Mn resources has created a scarcity of these resources, which is emerging as a major challenge for the manganese and steel industry. Manganese ore resources are mainly distributed in South Africa, with about 32 percent; Ukraine, with about 17 percent; Australia, with about 17 percent; and Brazil, India, China, Gabon and Mexico, with lesser amounts.

By Ahmet Tezcan, Zeki M. Dogan, Yalçin Kaytaz

Autogenous grinding in Turkey was first applied to quartzite where the mill is grate discharge type with an internal diameter of 2.99 m, having a length of 3.20 m and a capacity of as to 11.0 tons per hour. The second autogenous grinding was applied to a copper ore at Murgul Cakmakkaya Flotation plant of (KBI) Black Sea Copper Works having three mills 26 feet in diameter and 10 feet in length in close circuit with hydrocyclones. Recently, alterations were made in grinding circust by adding pebble mills. Furthermore, rubber liners and lifter bars were introduced pebble extractor and classifier were new features in the primary mills and circulating load was reduced by 20-50 tons per hour. At the end of these charges, capacity of each mill line was increased to 48 tons per hour with a full capacity of more than 9000 tons per day. Thirdly, autogenous grinding has been executed successfully on the slags of Samsun Smelting Plant of (KBI) Black Sea Copper Works with a mill of 20 feet in diameter and 6 feet on length having pebble mill following autogenous grinding.

Jan 1, 1992

By Z. Hyder, M. D. Cleason

"INTRODUCTION Mine Ventilation has come a long way over the years. The main purpose of mine ventilation is to keep conditions in the mine safe for the worker so that the mine will be productive and profitable. Technological developments to the mine ventilation system itself and the development of mining techniques have helped improve the safety and productivity of the miners and the mine. Most of the developments to mine ventilation and to safety devices came as the result of serious mining disasters. Another effect of those mining disasters, especially in the late 19th century and after, was legislation to set specific safety standards for mines, especially in the underground coal mines. This paper will focus on the connection between mines disasters and the mine safety legislations promulgated because of those disasters. A BRIEF HISTORY OF MINE SAFETY LEGISLATION Mine legislation has a long history in the U.S. dating back well in the 1800’s. However, mine safety legislation is considerably newer. In 1891, the U.S. Congress passed the very first version of mine safety legislations setting up minimum safety standards. By today’s standards, the 1891 legislation was incredibly basic (7). It took a series of horrific mining disasters for Congress to take action a second time. In 1910, Congress established the Bureau of mines. The role of Bureau developed and changed over next 60 years. In 1995, Congress voted to disband it (27). Initially the Bureau was only charged with investigating and coming up with ways to reduce accidents in coal mines. It was not until 1941, when Congress formally allowed Bureau of Mines’ Inspectors into the mines. In 1947, the Congress enacted and adopted a set of federal safety regulations for the inspectors to follow (1). Finally, in 1952 Congress granted the Bureau of Mines the authority to inspect the mines and to issue citations and/or orders of withdrawals. This act was known as the 1952 Coal Act and the penalties were limited to civil penalties. It would take a couple more iterations of mine safety legislation for monetary and criminal penalties to be introduced (10). Up until 1966, mine safety legislation was directed primarily at underground coal mines and surface coal mines. Congress passed the Federal Metal and Nonmetallic Mine Safety Act of 1966, thus providing a set of standards for all mines to follow (1). The 1952 Coal Act was amended again to be the Federal Coal Mine Health and Safety Act of 1969. This amendment was the beginning of modern mine safety legislation (13). In 1973, Congress created what can be considered the first ‘version’ of the modern day MSHA (Mine Safety and Health Administration). The initial version was the Mining Enforcement and Safety Administrations or MESA. Congress created MESA to act as the enforcement agency, relieving the Bureau of Mines of that responsibility so they could focus on their initial purpose, the development of countries natural resources (14). As mining industry grew, mine safety and health became a greater concern and priority. More efforts were put in legislating the industry. The Federal Mine Safety and Health Act of 1977 provided the platform for today’s mine safety and health legislation. Under the Federal Mine Safety and Health Act of 1977, also known as the Mine Act, MSHA came into being (1)."

Jan 1, 2016

By Kai Wang, Chao Xu, Qiang Fu, Tong Yang, Chunyu Zhao, Wei Zhao

The stress of a coal seam is an important factor that affects the permeability of the coal seam and then affects the coalbed methane (CBM) drainage. In China, adjacent coal seam mining is an important method to reduce stress, which increases the permeability of the coal seam. However, in the process of mining adjacent coal seams, many coal pillars remain, which causes stress concentrations and results in a decrease in permeability. Therefore, it is important to study the influence of coal pillars on the stress of adjacent layers and its distribution and evolution in the floor rock. This paper took the Shendong Baode Coal Mine as a case study and investigated the influence of the coal pillar on the stress and permeability of coal seam #11. The results show that under a coal pillar, the relationship between the vertical stress of different floor depths and the width of the coal pillar can be divided into a negative correlation zone, transition zone, and positive correlation zone. The change in the coal pillar width does not affect the pressure relief range or the degree of pressure relief in the adjacent coal seams below the goaf. The field measurements show that after the mining of panel #81,505, the permeability coefficient of coal seam #11 under the goaf increased from 0.1434 to 26.3545 m2/( MPa2*d), increasing 182.7 times, and the drainage mixing volume of boreholes #1 and #2 increased from 1.24 to 1.52 m3/ min. While the permeability coefficient of coal seam #11 from 12.5 m in the coal pillar has only increased by 2.6 times, the drainage volume of boreholes #3 and #4 did not change significantly.

Nov 19, 2022

By A. J. S. Spearing, A. Mueller

The support of intersections in coal mines remains an important safety issue, mainly because the large diagonal span compromises the stability of the roof. This structural weakness is further exacerbated if the intersection is developed incorrectly, the pillar corners fail or the crosscuts are angled (not perpendicular). This report details the current support systems used and investigates unplanned falls of ground in intersections in coal mines throughout the United States. A possible failure mechanism is proposed and some suggestions are made to improve the effectiveness of the support in these vital areas.

Jan 1, 2009

By Karl R. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fie or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. most longwall coal mines in australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflowmonitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

May 1, 2013

By Jon A. Hummer, MICHAEL R. SHAHAN, Aleksandar D. Bugarski, Shawn Vanderslice

A study was conducted in an undergroundminewith the objective to identify, characterize, and source apportion airborne aerosols at the setup face and recovery room during longwall move operations. The focus was on contributions of diesel- and battery-powered heavy-duty vehicles used to transfer equipment between the depleted and new longwall panels and diesel-powered light-duty vehicles used to transport personnel and materials to various locations within the mine. Aerosols at the setup face were found to be distributed among diesel combustion-generated submicrometer and mechanically generated coarse aerosols. According to the data, the submicrometer aerosols downstream of the setup face were sourced to diesel exhaust emitted by vehicles operated inside and outside of the panel. Depending on the intensity of the activities on the panel, the outby sources contributed between 12.5 and 99.6% to the average elemental carbon mass flow at the setup face and recovery room. Extensively used light-duty vehicles contributedmeasurably to the elemental carbon concentrations at the setup face. The number concentrations of aerosols downstream of the setup face were associated with aerosols generated by combustion in diesel engines operated in the shield haulage loop and/or outside of the longwall panels. Entrainment of road dust by diesel or battery-powered load-haul-dump vehicles operated near the measurement site appears to be the primary source of mass concentrations of aerosols. The findings of this study should help the underground mining industry in its efforts to reduce exposures of miners to diesel and coarse aerosols.

Apr 14, 2020