Search Documents

By Austin Whillier, Duncan Mitchell

The problem of heat stress underground in the gold mines is approached on the basis of the heat transfer between the human body and the underground environment. Experimental measurements of radiant and convective heat transfer and a theoretical calculation of maximum evaporative heat transfer enable the maximum cooling power of an environment to be calculated in terms of the dry-bulb and wet-bulb temperature, the mean radiant temperature, the wind speed and the barometric pressure. For most underground applications the cooling power can be expressed as a function of wet-bulb temperature and wind speed only. The relative importance of wind speed and wet-bulb temperature can be assessed: in working places where wind speed is low additional cooling of workmen can be achieved better by increased wind speed than by decreased wet-bulb temperature. The wet kata reading proves to be of limited value as an index of heat stress because environments with equal wet kata do not necessarily have the same cooling power. Finally, thermal equilibrium with the environment is possible when cooling power equals or exceeds the rate of metabolic heat generation. The rates of metabolic heat generation for various underground tasks are indicated.

The block caving mining method is used to mine large orebodies in weak rock types. The layout for block caving requires that a considerable amount of development is carried out on the extraction drives and drawpoints at the bottom of the caving block. The development further weakens the rock mass, and stability problems arise in the extraction drives and extraction pillars. This paper describes the application of three-dimensional boundary element models in analysing alternative extraction level layouts for a block caving mine. The objectives were to establish whether the use of lateral pillars between drawpoints was warranted, and whether the lateral pillars should be offset or not. The stability of the rock mass within the pillars as well as the stability of the extraction drives were taken into account. The results showed that after undercutting, the horizontal and vertical stresses in the extraction level would be reduced. The lateral pillars would significantly improve the stability of the extraction pillars and extraction drives. There would be a minor improvement in stability if the lateral pillars were offset.

Jan 1, 1987

An evaluation was made of the wear and performance characteristics of liter bars, and the cost-life effectiveness of backing materials for rotary-mil liners. In a large run-of-mine mil in which the liter bars were mounted on grid liners of austenitic manganese steel (AMS), the liners had an average life that was five to six times that of equivalent unprotected liners. For a single mil, this is equivalent to annual savings in the cost of materials of up to R320 000, and to a downtime of 100 hours. Of the five materials tested in a large pebble mil grinding quartzitic ore, AMS grids and 'white iron' blocks performed best on a cost-life basis, with possibly improved performance from a real white cast iron. (The 'white iron' was shown by microstructural analysis to contain flake raphite and pearlite, being in reality a grey cast iron.) The high-chromium white iron had by far the longest predicted life, with mild steel a surprising second. Rubber was shown to last well in this type of mil. The wear rates of liners change during their lifetimes. The protective effect of liter bars was clearly illustrated by the reduction of over 40 per cent in the wear rates of the liners when the lifter bars were renewed to a height of 80 mm from a fully worn height of 35 mm.

Jan 1, 1991

By M. A. de Ruijter

Bracken Gold Mine ceased mining operations during February 1993. The clean-up of the gold plant, which had already commenced in September 1992, was completed in January 1994. The mine had been in production since early in 1962 but, because of a decreasing ore reserve, increasing working costs, and a relatively low gold price, closure had become inevitable. The closure had been under consideration since August 1983, when the first estimate was made regarding the amount of gold that could be recovered from the clean-up operations. Until that stage, it had been accepted that Bracken would conform to the commonly accepted idea that 0.25% of the total gold produced by the plant would be recovered during the clean-up operation. This idea was dispelled when the initial estimates indicated that the gold recovery would vary between 0.049 and 0.095%. The actual figure realized was 0.036%, showing that there is no generalforl1ula for the calculation of the amount of gold to be recovered from such clean-up operations. During the clean-up operation, Bracken became an unexpected contributor to the State's Reconstruction and Development Programme by having al the mine and plant buildings purchased and converted into a community development centre. This shortene4 the time available for the clean-up, and several of the buildings remained intact. However, the foundations and sub-soils had been sampled extensively, and it is considered that no recoverable gold was left behind.

Jan 1, 1996

By S. L. Crouch

This paper describes a numerical procedure for the computation of the displacements and stresses induced by the mining of a tabular ore deposit in faulted ground. The numerical procedure is based on the displacement discontinuity method, which can be regarded as an application of Salamon's 'face element principle' to cases in which the reef plane is faulted into several sections, or even folded in an arbitrary way. An element of a fault is modelled in the same manner as an element of the reef, except that a fault element is allowed to undergo permanent inelastic deformation (i.e., slip) if the stresses transmitted through the fault-filling material satisfy a Mohr-Coulomb yield condition. An iterative technique for the incorporation of a Mohr-Coulomb yield condition in the general displacement discontinuity method is explained. This technique is illustrated by means of a simple example involving the mining of a flat-lying reef intersected by a fault. The displacements and stresses at selected locations along the fault are examined as the reef is mined, element by element. A consideration of the energy changes reveals that the occurrence of slip along a fault leads to a sudden increase in the energy release rate due to mining as the excavation intersects the fault. The energy release rate then falls off abruptly to a value less than that which would occur in the absence of any slip, and gradually builds up to re-establish the conditions that would exist in unfaulted ground.

Jan 1, 1979

By N. A. Barcza

An investigation was conducted into the reactions between the slag system MnO-CaO-MgO-SiO2(AI2O3) and the alloy system Mn-Fe-Si-(C). Synthetic slags representative of plant melts and a plant alloy were reacted in alumina crucibles at temperatures of 1400°C, 1450°C, 1550°C, and 1600°C. In similar experiments, slags were used that comprised a South African manganese ore with various amounts of lime and several synthetic alloys with various silicon contents and manganese-to-iron ratios. These experiments were conducted in a vertical molybdenum-wound resistance furnace with full temperature control. Slag-to-alloy ratios were also varied during the tests. The rate of reduction of Mn.O3 and the MnO from the slag by the silicon in the alloy was extremely rapid, most of the reaction being completed within five minutes. The strongly exothermic nature of the reaction resulted in considerable generation of heat at the slag-alloy interface, causing convectional stirring of the contents of the crucible and promoting the rate of reaction. Equilibrium was usually attained after fifteen minutes. The major limitation governing the recovery of manganese is the need for the silicon content of the alloy to meet a maximum specification of 2 per cent. Higher concentrations of silicon in the final alloy of between 8 and 12 per cent favour good recoveries of manganese from the slag, but, since such an alloy is not salable, lower recoveries must apparently be tolerated. In alloys of 2 per cent silicon, low activities of the silicon are responsible for poor recoveries of manganese. The activity of MnO in the slag can be increased by moderate additions of CaO and small amounts of MgO, i.e., by an increase in the basicity of the slag.

Jan 1, 1979

DISCUSSION: The value of incentive payments in the mining industry by K; SMITH Published in the Journal, May 1974 H. P. CARLISLE* The author has drawn attention to one of the most important of mining problems, viz productivity, and in so doing has highlighted, perhaps inadvertently, the difficulty of assessing productivity. Competition for Students Each year the Institute offers a prize (or prizes should the entries warrant it) of up to R100 for the best paper or dissertation on a topic appropriate to the interests of the Institute. Corrigendum The Journal, May 1974, p. 377 We regret that the last portion of A. A. Hazell's contribution to the paper 'The value of incentive payments in the mining industry' by K. Smith was printed in the wrong sequence.

Jan 10, 1974

By J. T. Davies

Note: Melting techniques in the iron foundry by J. T. DAVIES* INTRODUCTION The selection of melting equipment for use in an iron foundry has for several years been the subject of numerous discussions, papers, and conferences. The controversy that has raged throughout the world has been brought about by the following factors: IF AC Symposium The 2nd IF AC Symposium on Automation in Mining, Mineral and Metal Processing will be held from 13th to 17th September, 1976, at the Carlton Hotel, Johannesburg. Advance registration takes place on 12th September, 1976. World phosphates The Minerals Bureau of the Department of Mines has released the second publication in its series of reports on the economic aspects of minerals that are of particular importance to South Africa.

Jan 7, 1976

By N. T. Halgreen

The use of coal for combustion, carbonization, and the production of synthetic fuel is discussed briefly, highlighting the effect of certain physical and chemical properties of coal on these processes. The effect of consumer specifications of properties such as calorific value, ash content, moisture content, and size consist on the planning and operation of a mine are discussed, including the influence of coal degradation through time or mechanical means. The effects of various mining methods on these parameters and on the utilization of coal reserves are discussed.

Jan 1, 1984

By P. F. S. Jackson, A. Strasheim

In the survey "Analysis of South African raw bullion" the distribution of trace elements within the bullion have been shown to be distinctively dependent on the extraction process. In general the amalgamation process produces the more impure bullion with respect to trace elements. Some chemical and physical explanations are given for the differences that have been observed in the raw bullion as received at the Rand Refinery. The value of the spark source mass spectrographic technique in the study of the elemental impurities in bullion is demonstrated.

By F. W. Petersen

For the past thirteen years, the Universities of Cape Town and Stellenbosch have hosted an annual symposium to discuss topics relevant to mineral processing. Since 1987, this Symposium has been held under the auspices of the Western Cape Branch of the South African Institute of Mining and Metallurgy, and has become one of the main events on the national conference calendar. In 1989 and 1993, the symposia took the shape of international conferences. This year the 13th Annual Mineral Processing Symposium was organized by the two universities, the Cape Technikon, and the local branch of the South African Institute of Mining and Metallurgy, and was held at the Van Riebeeck Hotel in Gordon's Bay.

Jan 1, 1994

By R. C. Urquhart, W. P. Channon, D. D. Howat

Discussion: The mode of current transfer between electrode and slag in the submBerged-arc furnace by w. P. CHANNON, R. C. URQUHART, and D. D. HOWAT J. MEINTJES I have read the paper with much interest, and I should like to make a few observations. (I) The experimental work deals with resistance heating by an electrode immersed in a slag... AUTHORS' REPLY We thank Mr Meintjes for his critical analysis and helpful comments arising out of his study of our paper. Possibly we should emphasize at the outset that our experiments all related to the conditions in which the lower portion of the electrode was immersed in molten slag. We believe, however,

Jan 12, 1974

By M. C. van Blerck

This paper reviews the current mining taxes in South Africa, discussing the recommendations of the Mantis Technical Committee, the measures already implemented, and the future outlook. It is concluded that the tax burden imposed on individuals and on the corporate sector should be reduced, and that the taxation of al economic sectors should be neutral. The reforms implemented in 1989 and 1990 are expected to continue, and it is thought that, if the State commits itself to tax neutrality and reduces the ordinary rate of company tax to 40 per cent, the rate of mining taxes will also be lower. Ring-fencing is expected to be reduced further and the rules for capital safe-havens to be refined.

Jan 1, 1990

By M. J. Nicol

An electrochemical investigation of the dissolution of copper, nickel, and copper-nickel alloys in ammonium carbonate solutions by M. J. NICOL, Ph.D., B.Sc. (Hons.) (Wits.) (Visitor) The dissolution of copper and nickel in ammonium carbonate solution was studied by techniques involving electrohemical anodic dissolution and ring-disc electrodes. The rate of oxidation of both copper and nickel by copper (11) was shown to be controlled mainly by diffusion to the surface. Variations in rate with changes in copper (11) concentration, agitation, pH, ammonia concentration, temperature, and copper (I) concentration were investigated and rationalized in terms of their effects on the electrochemical half-reactions involved. Evidence was found for the passivation of nickel and nickel-copper alloys of more than 50 per cent nickel.

Jan 6, 1975

By K. M. Banks

Multiple-pass hot-strip-rolling schedules of carbon steels and niobium-microalloyed ferrite-pearlite steels were simulated on a Gleeble 1500 thermomechanical test apparatus. The effects of finishing temperature, coiling temperature, and chemical composition on the as-deformed ferrite grain size and hardness of the steels were determined. Low finishing temperatures and low coiling temperatures both contributed to ferrite grain refinement. Good agreement was found for the microstructure and hardness of the steels between the as-ruled condition and the results obtained from rolling simulations. The progress of recrystalization and precipitation was followed from examinations of the flow-stress curves during the hot-rolling simulations. The flow-stress behaviour during the finishing passes was consistent with the resulting changes in final ferrite grain size. It was found that the no-recrystalization temperature, TNR, is raised by increased additions of niobium.

Jan 1, 1993

By J. H. Bulloch

The paper gives an assessment of the available data on the linear elastic fracture mechanics involved in stress corrosion cracking and in the behaviour of reactor pressure-vessel materials exposed to a simulated pressurized water-reactor environment. As a result of the different experimental techniques used in the various studies mentioned, only a few detailed conclusions can be drawn. The data from constant-displacement wedge-opening loading (WOL) tests, with the exception of one study, exhibited very limited or no crack extension during exposure periods of up to 14000 hours. The data from constant-load tests indicated evidence of crack extension, but the nature and extent of the crack extension are still unclear. When crack extension did occur, it was exclusively transgranular in nature. Certain differences in the available test data are tentatively explained in terms of the experimental procedures used, and the need for a consistent code of experimental techniques is highlighted.

Jan 1, 1987

By V. E. Ross

A computer program was developed that incorporates a novel analysis of the behaviour of the froth in full-scale cells to predict the performance of the froth over a wide range of operating conditions. The program has the distinct advantage that it can be easily implemented on a microcomputer, which allows rapid computation and processing of the results. The program utilizes experimental data obtained in flotation-plant and laboratory testwork to provide parameters for the froth model under an initial set of operating conditions. These parameters can then be used in conjunction with a model describing the transfer of material from the pulp to the froth to predict the performance of the cell when its dimensions and operating variables are changed during scale-up.

Jan 1, 1987

By H. M. Friede

Notes on the composition of pre- European copper and copper-alloy artefacts from the Transvaal by H. M. Friede. Ph.D. (Visitor) Seven copper artefacts (five ingots and two ornaments) found at prehistoric sites in the Transvaal were submitted to analysis. All the artefacts showed a high copper content and a relatively Iow level of impurities. A little-known ingot type from the Limpopo Valley ('nail' ingot) is described, and its analysis is given. The analysis of two copper ornaments that come from sites dated to the 5th Century AD. and the 11th Century AD. showed the constancy of the composition of copper articles over long periods. The well-known 'Blaauwberg Ingot' was re-analysed, and the results showed that this ingot cannot be regarded as a true bronze. Analytical values for the composition of three brass artefacts from Bambandyanalo (Mapungubwe), Northern Transvaal, are given. Some aspects of pre-European bronze manufacture and brass smelting, and of early metal trade from the East Coast into the interior of South Africa, are discussed.

Jan 2, 1975

Scrap printed circuit boards were selectively smelted at 1 200°C to produce a metallic alloy having three phases. These phases were identified as a lead-rich phase, a low tin content alpha bronze phase, and a high tin delta phase. Electrochemical leaching studies on this alloy were done in 1 mol/dm3 sulfuric acid or in 2 mol/dm3 hydrochloric acid (adjusted to an ionic strength of 3 mol/dm3). The lead rich phase was more strongly passivated in sulfate media, and in this medium the high tin content delta bronze was more resistant to corrosion than the lower tin alpha bronze phase. In chloride medium the lead phase and both bronze phases corroded readily, but with current densities about an order of magnitude lower than in sulfate medium (static conditions) for the bronze phases. The high tin delta bronze phase was found to form a passivating layer in sulfate media. A similar layer was not seen in chloride medium. The leaching studies in sulfate medium also showed the existence of an alpha bronze phase of lower tin content in the centres of the alpha phase grains. This phase was quite resistant to leaching in sulfate medium.

Jan 1, 2009

By Z. Hou

ABSTRACT: Short-term strength, damage and healing boundaries for rock salt are experimentally determined and integrated into the Hou/Lux-MDS damage-healing model. This model can be used to describe the mechanical behaviour of rock salt during a damaging process (under high stress to strength ratios) as well as during a healing process (under very low stress to strength ratios with high confining pressure). The development of the damage and the stress to strength ratio in the excavation damaged zone (EDZ) of a storage cavern under a minimum internal pressure as well as the development of the healing of damage and the stress to strength ratio under a subsequent maximum internal pressure are investigated project-related. The results of the investigation make it possible to shift the permissible minimum pressure boundary down, allowing the optimisation of decisive economic characteristics of storage caverns. RÉSUMÉ: Le comportement court terme, l’endommagement et les conditions de colmatage pour le sel gemme ont été étudiés expérimentalement et intégrés dans le model endommagement-colmatage Hou/Lux-MDS. Ce modèle permet de décrire le comportement mécanique de sel gemme pendant le processus d’endommagement (sous fort rapport contrainte-résistance) et le comportement du processus de colmatage sous très faible rapport contrainte-résistance avec forte pression de confinement. Le développement d’endommagement et le rapport de contrainte-résistance dans une zone d’endommagée (EDZ) d’une cavité de stockage avec un maximum de pression de soutènement ont été étudiés. Les résultats de cette étude permettent de conclure qu’il est possible de baisser la pression de soutènement, et par conséquent d’optimiser les caractéristiques économiques décisives des cavité de stockage. ZUSAMENFASSUNG: Für Steinsalz werden Festigkeits-, Schädigungs- und Verheilungsgrenze experimentell ermittelt und in das Schädigungs-Verheilungs-Modell Hou/Lux-MDS integriert. Damit kann das mechanische Verhalten von Steinsalz sowohl bei einem Schädigungsprozess (mit hohen Ausnutzungsgraden) wie auch bei einem Verheilungsprozess (mit niedrigen Ausnutzungsgraden) beschrieben werden. Projektbezogen werden die Schädigungs- und Ausnutzungsgradentwicklung in der Auflockerungszone einer Speicherkaverne unter einem minimalen Innendruck sowie die Verheilungs- und Ausnutzungsgradentwicklung unter einem anschließenden maximalen Innendruck untersucht. Die Untersuchungsergebnisse erlauben, die zulässige Minimaldruckgrenze nach unten zu verschieben, so dass entscheidende wirtschaftliche Kenngrößen von Speicherkavernen optimiert werden können.

Jan 1, 2003