Search Documents

By D. J. Shields

The U.S. Bureau of Mines has developed a microcomputer-based mineral modelling system that enhances analytical capabilities of the agency. It draws upon the extensive data base previously developed for the Bureau's Availability studies. The model is first formulated as a generalized network flow optimization problem, the optimal flows from which are fed into a transportation algorithm. The goal of the modelling system is first to fulfill prespecified demand at the minimum opportunity cost and second to identify feasible, optimal trade patterns. The system facilitates the analysis of policy issues on a real-time basis and supports the Bureau's mission to assess mineral resources.

Jan 1, 1987

By L. Shoke

The aim of this study was to develop an in-house tensile testing procedure that would yield accurate and reproducible parameters as input material properties into computational models for numerical simulations of the mechanical behaviour of TM380 mild steel. To achieve this objective, we reviewed the ISO 6892:2009 tensile testing standard along with reported good practice guidelines. Tensile tests were conducted on a dog-bone shaped TM380 mild steel specimen with strain gauges attached on either side, to monitor alignment and measure strain, using three different types of tensile testing machines. Parameters quantified included yield stress, ultimate tensile strength, and modulus of elasticity. The values of these parameters were found to be in agreement with the values supplied by the manufacturer's specification and showed minimal variations between laboratories. Thus it can be concluded that the tensile test procedure used resulted in accurate and reproducible results. The strain values calculated as per standard were in disagreement with those determined from extensometer and strain gauges and resulted in lower elastic modulus values. This confirms that the current testing procedures require the use of long-range strain gauges or extensometer to determine the strain. A chemical analysis was conducted to verify the specification by the manufacturer. The specimen was found to be fairly homogeneous with minor sulphide inclusions. The micrographs reveal a pearlite and ferrite structure typical of mild steel, and the fractographs show a dimpled surface typical of ductile fracture, which is an attribute of mild steel.

Jan 1, 2013

By E. Marè, D. R. Groot, R. Engelbrecht, T. Coetsee

Hydrogen peroxide is often used as an oxidising agent in experimental waste electronic equipment (WEE) leaching work. However, the high cost of peroxide is a negative factor in its consideration in further process development. A few studies have reported on the efficient application of peroxide addition schedules to ensure optimum reagent consumption. Large quantities of unleached substrate material contained in WEE feed material result in a large dead volume of material in the leaching reactor. This factor necessitates fast reaction rates to enable the use of a high feed material throughput reactor to enhance overall project viability via hydrometallurgical processing. In this study the effects of hydrogen peroxide addition schedules on base metal leaching efficiency and solution temperatures were tested at laboratory scale. The results showed that overall peroxide consumption can be optimised to lower levels by matching peroxide additions to the particular feed material’s leaching behaviour. A simplified integrated model for peroxide decomposition is used to explain its effect on solution temperatures and leaching rates. Keywords: Peroxide consumption, waste electronic equipment, copper leaching, integrated model

Jan 1, 2020

By Ernst-Ulrich Reuther, Alexander Donmen

Mine ventilation in the German coal mining industry is concerned mainly with problems of thermal environment arising from greater depths and with increasing emission of methane gas. The development of computer techniques over the past ten years for solving these and ancillary problems is reviewed. The emphasis from a planning and control point of view falls mainly on ventilation network calculations, temperature predictions and advance estimates of methane emission.

Jan 1, 2014

By M. Bryson, G. Marap, M. Ntlhane, M. D. Hlahane

This study investigated flotation of phosphate from a low-medium grade 8-12% P2O5, 65-73% SiO2 sedimentary phosphate ore from Kropz Elandsfontein (herein referred to as Elandsfontein) in South Africa. Quantitative evaluation of minerals by scanning electron microscopy (QEMSCAN) was used to determine apatite grain size distribution, liberation and mineral association in the F2 horizon sample. The mineralogy indicated that apatite was liberated and for the Elandsfontein plant to operate at the design throughput, the flotation feed has to be milled to a coarse grind ranging between 300 μm and 425 μm. Reverse flotation process routes using varying reagent dosages, and flotation feed top sizes that could possibly yield a final product of 31% P2O5,10% SiO2 at a reasonable +70% P2O5 recovery were investigated. Based on the results, a split circuit of coarse (-300+212μm) flotation and fine (-212+20μm) flotation, was mostly preferred as compared to treating the whole ore. A final combined concentrate of 31% P2O5 and 10% SiO2 with P2O5 recovery of 84% could be produced from the reverse split circuit. The robustness of reverse flotation for both coarse and fine fractions was further investigated. Reverse flotation of the fines fraction was found to be robust and produced a final product of 31% P2O5. It was however more challenging to achieve the required product grade and recoveries on the coarser fraction (-425+212μm), suggesting that reverse circuit was not adequately robust at fractions coarser than 300μm. Keywords: Phosphate, sedimentary, reverse flotation, particle size

Jan 1, 2020

By A. D. Pienaar

The aqueous chemistry of niobium and tantalum compounds with hydrofluoric acid is a mature field of investigation. In contrast, very little attention has been paid to reactions of these compounds in non-aqueous environments. Similarly, reactions of elemental fluorine with niobium and tantalum compounds have received little more than cursory attention in literature. This work discusses the isothermal reaction kinetics derived from thermogravimetry, using a less redundant approach than is currently the standard. We also discuss the most likely kinetic models for this reaction.

Jan 1, 2012

By D. H. Batchelor

Efficient modern-day mining operations are turning increasingly to technology to combat rising operating costs in an adverse economic climate for the industry. Computerised truck dispatching is one such technological advance that has enhanced the efficiency of the mining operation at Palabora. The economic incentives, basic operation and general system benefits of Palabora's computerised truck dispatching system are considered.

Jan 1, 1987

By D. H. Diering

Definition of mineral resources and reserves forms the basis for effective mine planning and reliable public reporting of mineral assets. Historically, the mineral resource and reserves declaration process has been the domain of the geology and surveying disciplines, with the declaration of the reserves by the surveyor being based on the application of modifying factors to the declared resources available for mining. As part of an ongoing process to improve efficiency, reliability, and reproducibility of results, this approach has been revised and enhanced through the introduction of a revised process and reconciliation tools. The revised approach to reserve definition is based on the definition of scheduled resources, at an appropriate confidence estimate in the context of an approved business plan, over the anticipated life of the mineral asset being applied to define reserves. This planning and scheduling is developed, during the annual business planning process, by the mine planning department using tools such as CADSMine?. The scheduled area together with the application of revised modifying factors is tabulated in the BME (basic mine equation) and reflects the mine production plan over time. Simplification of the modifying factors to dilution and losses underpins the simple yet robust approach to improved definition of reserves in this process and in the basic resource to reserve equation (BR2RE). Dilution intrinsically affects grade but not metal content, whereas the losses reflect both the efficiency of mining and planning and are reflected in metal losses, area losses, or both. Reconciliation of the derived 'resource converted to reserve' area (which is based on the business plan from CADSMine?) versus the 'resource available for mining' (which is derived from Datamine?) underpins the robustness and auditability of the reserves declaration. This R&R accounting and reconciliation approach is transparent and facilitates interrogation of the logic and rationale of long-term business planning and project strategy. These numbers are processed and reported in the logic of the basic resource equation (BRE), which also addresses aspects such as white areas (future and historic), tail management, and partial extraction (non-scheduled pillars, etc.) in compliance with SAMREC definitions. Areas that do not have the necessary confidence and data support to be declared as resources find their space as pre-resource (outside the domain of public reporting), outlining existing potential for future extraction and reporting. Use of the BRE leads ultimately to a complete, refined accounting and reconciliation-oriented approach for all production entities. The revised resource and reserve process includes the discipline of mine planning as intrinsic to the definition and declaration of resources and reserves. Subsequent to the change in process, the resources and reserves have truly become the domain of the mineral resource management discipline. This paper defines the logic of the basic resource equations and outlines their application in the definition and reconciliation of mineral resources and reserves at Anglo American Platinum Limited.

Jan 1, 2013

By A. V. Z. Brink

This paper describes the development of a monitoring architecture that allows for continuous monitoring of the process of mining, the underground environment, the state of the rockmass and its response to mining. The system is based on an open standard and is non-propriety. It allows for dense sensor arrays in the workplace, wire less communication to the closest power line, and TCP/IP communication to a central server. Continuous monitoring and quantification of the appropriate parameters allows a mine to optimise its mine process; to dynamically access the safety and health risk to people and equipment; and to quantify exposure to potential heath hazards such as dust, gas or noise. Current application examples of continuous monitoring include an application to optimise drilling and blasting thought fragmentation monitoring; an application of wireless sensor network-based monitoring in to provide early detection of potential rockfalls; and a trail to continuously assess the gold grade at the shaft through correlation with radioactivity. It is unlikely that a single monitored parameter will provide adequate knowledge of the assessed risk or even an optimisation approach. Multiple parameters are being combined using cognitive science tools such as Bayesian theory and other statistical methods to improve the accuracy and relevance of, for example, risk quantification. The decision maker is not confronted with massive amounts of raw data but rather with a single knowledge statement such a probability of failure, a human physiological strain index or an optimisation index.

Jan 1, 2008

By I. Ince, S. Kahraman, M. Rostami, B. Dibavar

The density, porosity, and strength of rocks are fundamental in the design of geo-engineering projects. Determining these properties requires the preparation of smooth core samples, which is usually impossible for soft rocks. Besides, only fragmented samples may be available in some projects. A method for predicting rock properties from rock particles such as drilling debris would therefore be useful. This study was undertaken to develop prediction equations for compressive strength (UCS), tensile strength (BTS), density, and porosity values from the crushability index (CI) obtained from rock fragments. The results showed that UCS, BTS, density, and porosity were strongly correlated with the CI. The physical characteristics and strength of rocks may be predicted with the help of the derived equations. The CI test is a valuable tool for estimating rock properties in drilling projects and in situations where core specimens are not available.

Mar 14, 2024

By F. Smit

Mining and plant practices can benefit from preconcentration of UG2 platinum ores in a dense medium separation (DMS) plant. The main benefit of DMS is the selective discard of waste from the feed stream, thus improving project economics while reducing the power and water requirements for processing. On the mining side, with the correct combination of variables, implementing DMS as a pre-concentration step can reduce cut-off grades and, as a result, increase ore reserves. In addition, the use of DMS technology gives the mine team the opportunity to consider alternative mining methods for an operation. The challenges of balancing the mining tonnage, methods, and resulting grades with the process plant size, recoveries, and DMS discard volumes have resulted in the development of a model to optimize value on new projects or existing operations. This paper will focus on these benefits from a mining and plant perspective, quantifying the water and power savings, and look at the economic benefits of preconcentration and the effect of metal prices, plant feed grade, and DMS efficiency in different mining environments.

Jan 1, 2013

By I. James, R. J. Durrheim, M. S. D. Manzi, O. Valeshin, J. Lepine, L. V. Socco, C. Colombero, A. Malehmir, M. K. Rapetsoa, M. Sihoyiya

The FUTURE project aims to enhance seismic surveying in South African mining by integrating advanced acquisition technologies. In this paper, we detail surface and underground seismic surveys at the South Deep gold mine as part of the project. Surface seismic acquisition used co-located broadband micro-electromechanical sensors, one and three component recorders connected to geophones, distributed acoustic sensing using a straight fibre optic cable, along with a 6 ton broadband seismic vibrator operating with 4–180 Hz linear sweeps. In addition, underground surveys employed a combination of straight, and helically wound fibre optic cables, cabled-based and nodal sensors, along with a 500 kg drophammer mounted on a skid steer bobcat. The surface and underground seismic arrays were time synchronised using a GPS-time transmitter to allow for accurate seismic data recording in a GPS-denied environment. Results show the efficacy of these techniques in acquiring high-resolution seismic data, revealing detailed subsurface geological structures and mineralisation down to 3500 m below ground surface. Surface data revealed clear seismic reflections corresponding to the Black Reef and Ventersdorp Contact Reef. An underground P-wave velocity model exhibits low velocity anomalies that are associated with fracturing, while a P-wave reflection stack section shows significant reflections and a degree of faulting below the tunnel floor that was not observed on the surface reflection seismic data. We highlight the potential of these technologies to enhance safety, efficiency, and sustainability in mining. This study sets a benchmark for future reflection seismic surveys, paving the way for safer, more efficient, deep mineral exploration and extraction practices.

Jan 12, 2025

The 96th Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room of the Transvaal Automobile Club in Johannesburg on Wednesday, 11th August, 1993. OBITUARIES The President announced the deaths of the following members of the Institute during the past year. Life Fellow E.F. Laschinger. Other Members R.K. Boright, J.S. Jacobi, R.D. Power, J.H. Cannon, C.J. du Plooy, L.B. Mcrae, C.P. Rossouw, A.L. Sillars, A.W. Heugh, R.K. Briggs, P.J. Stark, and C.S. Stott. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, all rose and observed a moment of silence.

Jan 1, 1993

By I. J. Kotzé, R. T. Jones

Conventional PGM matte smelting requires the presence of a certain quantity of base metal sulphides in order to collect the platinum group metals in a molten sulphidic matte phase in the furnace. Furthermore, the quantity of chromium oxide in the feed materials is controlled in order to avoid the build-up of high-melting chromite spinels in the furnace. Mintek has developed a process for smelting difficult PGM-containing feed materials that contain low amounts of sulphur and/or high amounts of chromium oxide. A DC arc furnace is used to provide the appropriate conditions to generate an iron alloy that collects PGMs very effectively, leaving extremely low residual quantities of PGMs in the slag. Various feed materials have been treated successfully in furnace campaigns running at power levels up to 1.5 MW. The longest of these campaigns was run continuously for more than four months, treating more than two thousand tons of materials such as low-grade concentrates, revert tailings, and converter slag. The campaigns demonstrated the robustness and versatility of the process, and proved that it is possible to sustainably produce a PGM-containing alloy and discardable slags containing an average of less than 1.4 g/t of PGMs over the entire campaign. Keywords: DC arc, smelting, furnace, platinum, PGM, revert tailings, converter slag, ConRoast

Jan 1, 2004

By J. W. Wilson, J. G. Taylor

The mechanization of haulage drilling in the gold mines of Anglo American Corporation by J. w. WILSON, Ph. D., C.Eng., M.AIME, F.!.Min.E., F.I.M.M. (Fellow), and J. G. TAYLOR, A.C.S.M., C.Eng., M.!.M.M. (Visitor) Some one-thousand kilometres of tunnels are mined annually in the gold mines of South Africa. Until two years ago, mechanized drilling on South African gold mines was not an economic proposition because of the availability of inexpensive labour and the fact that mechanized equipment developed for other mining markets could not perform satisfactorily in the tough, abrasive quartzites of theWitwatersrand System. A project team from the Technical Development Services Organisation of the Anglo American Corporation, in collaboration with various manufac turers of drill rigs and drill steel, has been concerned with the development of suitable equipment for mechanized main-haulage drilling. After two-and-a-half years of extensive testing and development of drifters, drill steels, and bits, many of the problems encountered have been sotved, and gradually jumbos mounting pneumatically and hydraulically powered drifters are being phased into production on various gold mines of the Group. A description of the development work is given, and actual operating results are recorded, together with details of the drilling and blasting techniques used.

Jan 1, 1975

By P. Linzer, L. M. Linzer

The gravity method is often applied in mining-related scenarios such as geological and mineral exploration, detecting subsurface cavities and voids (“receptacles”) that may become sinkholes, siting of surface structures, fault-mapping, and more. It is also widely applied in geotechnical engineering to map subsurface karst profiles and to detect subsurface cavities, such as can occur in open pit mines. While it is widely acknowledged that, compared with other available geophysical methods, this method is the most applicable to the karst profiling problem, survey geometries applied in the field are often far from optimal. The gravity surveying specifications prescribed in SANS 1936 omit some key requirements for optimal survey outcomes, and this paper is intended to fill those gaps. The authors have seen scopes of work that require only a few measurements over the footprint of a proposed structure, indicating a lack of understanding of the nature of the gravitational field. A single gravity measurement is subject to the camouflaging effects of several influences, many of which can be larger than the anomaly caused by the subsurface density variation itself. Papers in the body of literature show an awareness of the need to map the regional field so that it can be subtracted to unmask the residual gravity anomaly, but rarely do they examine how instrument sensitivity governs the size of detectable anomalies or discuss how a detailed terrain correction can be instrumental for isolating faint targets. This paper aims to explain how to apply the gravity method correctly to mining and geotechnical problems, specifically in the detection of subsurface cavities. It discusses various factors to assist with optimising the acquisition of gravity data and its processing so as to maximise the practical value of gravity surveys.

Sep 1, 2025

By N. J. Alderman, R. Haldenwang

Flumes are ubiquitous throughout the mining and minerals processing industries as well as being used in the polymer processing and pulp and paper industries. With the increased demand for the transport of highly concentrated slurries in rectangular open channels, there is an impetus for a better understanding of the role of rheology in flow hydraulics. Until recently, design of such channels has been based on either the Chézy or Manning equations used for modelling open channel flow of Newtonian fluids. This has been done for modelling turbulent flow of low concentrated slurries with some success. However, this is not the case for highly concentrated slurries where the flow in the channel is no longer turbulent. Unlike Newtonian fluids, work carried out on flow of pseudo-homogeneous, non-Newtonian fluids in open channels is somewhat limited. Moreover, these results have been published in a variety of sources. This paper attempts to give a critical review of the work carried out on Newtonian and non-Newtonian flow of pseudo-homogeneous non-settling slurries in rectangular open channels. A comparison is also made of the models based on power law, Bingham plastic and Herschel-Bulkley fluids for laminar and turbulent flow in rectangular open channels.

Jan 1, 2007

By J. Labuschagne

The primary factor contributing to the profitability of a platinum mine and its associated concentrator is the time taken from the first hoist of material from underground to the first batch of concentrate shipped. To minimize the time it would take to produce concentrate without stopping because of a lack of feed material a project was undertaken to integrate the mining model with a concentrator production schedule () in the most capital-effective manner. A secondary goal was to ensure detailed stockpiling requirements, as the concentrator is in an area where ?visual pollution? is to be avoided. To achieve this a dynamic stockpile model was created utilizing the mine production schedule resolved into a daily production figure. Four different concentrator development models were then proposed. The difference between the mine production and concentrator consumption was integrated over the life of the mine to provide the accumulated stockpile tonnages for both Merensky and UG2 ores. The stockpile levels were never allowed to fall below zero to prevent a situation where the concentrator was operational without feed material,. When a development option was selected, the standard metallurgical performance calculations were used to derive a concentrate production schedule, that was then used as a basis for commercial concentrate sale negotiations.

Jan 1, 2012

By J. Autio, H. Malmlund

The excavation damage zone (EDZ) caused by drill and blast excavation consists of intense damage adjacent to the remaining half barrel of the blast hole, new fracturing induced by the blast and reactivation of pre-existing fractures. The properties of intense microfracturing adjacent to the half barrels of remaining blast holes are based on study of rock samples from ZEDEX-tunnel and it’s extension at Äspö and the Research tunnel at Olkiluoto in Finland. The new and reactivated fracturing is based on results of mapping of slots cut in the rock in ZEDEX-project. The zone of increased porosity adjacent to half barrels, which penetrates to a depth of some centimeters was studied by using novel 14C-PMMA method. The penetration of the radial fractures, which is an order of magnitude deeper, was studied by mapping using color penetrant. Results of EDZ studies carried out at Äspö HRL in Sweden and in Research Tunnel at Olkiluoto show that the properties of EDZ can be affected significantly by engineering design. The result imply that the additional pore volume caused by distinct fracturing around the blast holes caused by state-of-the-art smooth blasting technique could be of the same order as that of the damaged zone adjacent to the surface of the half barrels. Durch Bohr- und Sprengarbeiten entstandene Eigenschaften der Auflockerungszone: Die durch Bohr- und Sprengarbeiten entstandene Auflockerungszone besteht aus einem großen, an das Resthalbrohr des Bohrloches angrenzenden Schaden, neuer Rissbildung und einer Reaktivierung der bereits existierenden Risse. Die Eigenschaften einer immensen, an die Halbrohre der Restbohrlöcher angrenzenden Mikrorissbildung beruhen auf einer Studie über die aus dem ZEDEX-Tunnel gewonnenen Gesteinsproben und deren Fortsetzung im Untertage-Labor Äspö (Hard Rock Laboratory, HRL) in Schweden und im Forschungstunnel bei Olkiluoto in Finnland. Die neue und reaktivierte Rissbildung basiert auf den Auswertungsergebnissen der Schlitze, die bei dem ZEDEX-Projekt ins Gestein geschnitten wurden. Die Zone der vermehrten, an die Halbrohre angrenzenden Porösität, die in ein paar Zentimeter Tiefe eindringt, wurde anhand der neuen 14C-PMMA-Methode untersucht. Das Eindringen der etwas tiefer gelegenen radialen Risse wurde anhand eines farbigen Eindringungsmittels untersucht. Die in Äspö und Olkiluoto durchgeführten EDZ-Studien zeigen, dass die EDZ-Eigenschaften wesentlich durch Engineering Design beeinflusst werden können. Das durch Bohrarbeiten verursachte Hohlraumvolumen der Rissbildung um den Tunnel herum ist ähnlich wie das Hohlraumvolumen der Bruchzone um die Bohrlöcher herum. Caractéristiques d’une zone endommagée par le creusement résultant d’un creusement par forage et dynamitage: La zone endommagée par le creusement résultant d’un creusement par forage et dynamitage présente un endommagement intense adjacent au demi-cylindre restant du trou de mine, une nouvelle fracturation et la réactivation des fractures préexistantes. Les caractéristiques de la microfracturation intense adjacente aux demi-cylindres des trous de mine restants reposent sur l’étude des échantillons de roche en provenance du tunnel ZEDEX et de son extension au laboratoire souterrain d’Äspö (« Hard Rock Laboratory » ou HRL) en Suède et du tunnel de recherche d’Olkiluoto en Finlande. La fracturation nouvelle et réactivée repose sur les résultats du placement des rainures sur la roche dans le projet ZEDEX. La zone de porosité accrue adjacente aux demi-cylindres et pénétrant à une profondeur de quelques centimètres à fait l’objet d’études recourant à la nouvelle méthode 14C-PMMA. La pénétration des fractures radiales, considérablement plus profondes, a été étudiée par placement en utilisant un agent pénétrant coloré. Les résultats des études EDZ effectuées à Äspö et à Olkiluoto montrent que les caractéristiques de l’EDZ sont susceptibles d’être affectées de manière significative par la conception technique. Le volume vide de fracturation résultant du dynamitage autour du tunnel est du même ordre que celui de la zone concassée autour des trous de mine.service.

Jan 1, 2003

By S. C. Maji, U. S. Chattopadyay, S. Chaudhuri, T. Gouri Charan

India is devoid of coking coal resources, which is a vital raw material for coke making. As a result it has to import about 80% coking coal for steel making. Indian National Steel Policy, 2017 has envisaged crude steel production around 300 million tonnes Mt) by the year 2030-31 and forecasts coking coal demand of 161 Mtpa (million tonnes per annum). One way of improving the indigenous resources is to study the performance of existing washeries and to improve the clean coal recovery by adopting suitable technology. A study was carried out, mainly to focus on the fine coal circuit of an existing coking coal washery, to generate the desired quality of clean coal. The operating coking coal washery being studied is presently feeding coal from nine different sources with varying feed ash contents. The coal fines varied in ash content ranging from 19.5% - 43.6%. For treating the coal fines, the washery has operated a spiral for the past few years. Performance studies were carried out, and it was found that the spiral is not efficient in recovering the cleans. Detailed investigations were carried out on the coal fines using flotation techniques, and it was found that to achieve a low ash clean coal, the froth flotation is a much better beneficiation option than a spiral, The studies showed that the recovery of clean coal through a spiral is 67.7% at ash content of 27.0%, while flotation tests showed a recovery of 68.1% at 16.5% ash content. Keywords: Coking coal washery, near gravity material, spiral washer, froth flotation

Jan 1, 2020