Search Documents

By M. V. HANSEN, Frank PERZ, Edward Thomas, C. H. SEELING

This is the second of a series of information circulars dealing with the control of roof and the prevention of accidents from falls of rock and coal . Their purpose is to focus the attention of the coal-mining industry on the most - common source of fatalities and injuries in mining coal and to disseminate information that may be helpful in combating the roof - fall hazard . Inasmuch as approximately 85 percent of roof - fall accidents occur in the face region , the importance of analyzing the accident - producing aspects of methods of roof support at the face or lack of method overemphasized . - - cannot be This circular is not intended to be an exhaustive treatise on methods of roof support in face regions but rather is a description of several methods of support that appear to offer distinct advantages with respect to safety and efficient operation .

May 1, 1948

By N. C. Tomoeda, W. D. Bensema, J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 350 meters (1150 ft .) and 488 meters (1600 ft .) . The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broad- band, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or E layers of ionosphere as an upper plane and the earth as a lower plane. The measurement systems used are similar to those used earlier. The technique is to record broadband, analog signals, digitize the data, and use a fast- Fourier transform to obtain spectral plots. This tech- nique is novel in that it can measure simultaneously all magnetic field energy within a limited portion of the spectrum for a limited time, and, after processing, reproduce the events occurring in that time interval in great detail .

Jan 6, 1974

By Leon W. Dupuy

"INTRODUCTION Scheelite occurring in tactite at the Black Rock tungsten mine, near Benton in Mono County, Calif., was investigated by the Bureau of Mines in cooperation with the Geological Survey as part of their search for additional sources of supply of strategic minerals authorized under the Strategic Materials Act. 3/4/The work accomplished by the Bureau, and the assays of samples taken are described in this manuscript. The ore found aided materially in prolonging the operating life of the mine during the recent national emergency, supplying much-needed tungsten for war use. ACKNOWLEDGMENTSIn its program of investigations of mineral deposits, the Bureau of Mines has as its primary objective the more efficient utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual development work, and prepares the final report. The Metallurgical Division, under the direction of C. C. Ralston, chief, analyzes samples and performs beneficiatibn tests."

Mar 1, 1948

By D. E. Wolfson

This report describes the carbonizing properties of the principal coal beds of Allegheny County, Pa., which rank low in the high-volatile A bituminous classification. Seven coal samples from 3 coal beds were selected for study, as follows: 2 each from the Redstone and Pittsburgh beds and 3 from the Upper Freeport bed. Selection was based on estimated reserves. The samples of Upper Freeport and Pittsburgh coals were satisfactory chemically for producing metallurgical coke. The ash contents of the samples of Redstone coal were moderately high. One of the samples of Redstone coal was high in sulfur content, and it would be difficult to upgrade to meet present metallurgical standards.

Jan 1, 1959

By D. Bienstock

A rig was constructed to burn 100 to 125 lb of coal per hour at 4,000° F in a cyclone burner with oxygen-enriched air preheated to 1,500° F to ascertain the problems in the coal-fired MHD generation of power. Potassium carbonate was added to the coal at several concentrations up to 1.23 g-moles/kg of coal (17 lb K2C03/100 lb coal). Boiler-tube materials maintained at wall temperatures of 800° to 1,500° F were exposed to the combustion effluent of 1,800° to 2,500° F. Practically complete removal of sulfur dioxide from the stack gas was achieved with the seed addition. Nitric oxide formation followed theoretical expectations at combustion temperatures with some decomposition of the NO occurring as the gas cooled flowing through the system. Nitrates in the fly ash were less than 1.7 percent of the total fixed nitrogen. With aqueous extraction of the fly ash a maximum recovery of 75 percent of the potassium was obtained. Haynes 25 was unattacked at a wall temperature of 1,500° F in combustion gas at 2,500° F; the stainless steels 310, 316, and 446 were resist-ant at a metal temperature of 1,100° F in gas at 2,100° F.

Jan 1, 1970

By A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effect of underground mining conditions on the activation of automatic sprinkler heads. Sprinklers were exposed to liquid fuel fires in a rectangular tunnel at airflows of 0, 45, 90, 150, and 250 m/min to determine the effect of ventilation and fire size on the time to activation. As the airflows were increased, the time to activate the sprinklers for a given fire size increased. Also, as the fire size increased, the activation time decreased. Temperature profiles of the tunnel showed that the maximum temperature near the roof was shifted downstream as the airflow increased. Experiments to determine the effect of rated activation temperature and response time index (RTI) value on activation time showed that the time to activate increased with increasing activation temperature, and decreased with decreasing RTI value. Exposure to the mine environment showed little effect on the activation times in large-scale experiments, and no significant effect in laboratory experiments. The results showed that airflow can have a significant effect on the activation times of automatic sprinklers. This needs to be considered in the design of effective sprinkler suppression systems for ventilated areas.

Jan 1, 2010

By B. K. Cantrell, K. L. Rubow

"Quantifying exposure to diesel exhaust aerosol in an underground coal mine depends on the ability to measure this component of respirable mine aerosol separately from coal dust. Such measurement is complicated by the carbonaceous nature of both the diesel and coal dust particulate that make up the respirable aerosol. Hence, special sampling and analytical techniques must be used to distinguish between these two aerosol components.As part of a continuing study of diesel exhaust aerosol characteristics, the U.S. Bureau of Mines has applied size selective sampling together with gravimetric analysis to separate and measure respirable diesel exhaust and coal dust aerosol concentrations in diesel-equipped underground coal mines. This technique is based on the premise that the diesel portion of the aerosol is predominantly submicrometer and the mineral dust portion is mostly greater than 1 µm in size. In the study, chemical mass balance (CMB) modeling, based on the distribution of chemical elements in aerosol and aerosol source material samples, is used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results.Based on the results of the study, the Bureau, in cooperation with the University of Minnesota and the U.S. Mine Safety and Health Administration (MSHA), have developed a prototype personal diesel exhaust aerosol sampler for underground coal mines. The sampler has three stages: a preclassifier stage to select for respirable aerosol, an inertial impaction stage with an aerodynamic diameter(d) size cut at 0.8 µm to separate diesel aerosol from mineral dust and collect the mineral dust, and a final filtration stage to collect the diesel fraction of the sample. The sampler has been evaluated in both laboratory and field experiments conducted by the Bureau, MSHA, and the Generic Minerals Technology Center for Respirable Dust (GMTC-RD)."

Mar 1, 1992

The coal reserve base is defined for coalbeds having sufficient thickness for underground mining within a depth range compatible with economic recovery. The reserve data are compiled by the Federal Bureau of Mines by updating and reevaluating previous estimates of the U.S. Geological Survey, State geological surveys, and others. Through the application of computer techniques, the tonnages are compiled by State, county, coalbed, and rank. Coal reserve base is allotted to sulfur categories by a statistical apportionment of data from available Bureau of Mines reports and records. The coal reserve base in those States east of the Mississippi River, minable by underground methods, is estimated to be 169 billion tons in coalbeds greater than 28 inches in thickness to a maximum depth of 1,000 feet. Excluding those coals in reliability categories other than measured and indicated, the underground reserve base includes 162 billion tons of bituminous coal and 7 billion tons of anthracite. Of the total, 27 billion tons contains 1.0 percent or less sulfur. Most of this low-sulfur coal is in the southern Appalachian area. Approximately 16 percent of the underground reserve base is without available analyses. Included in this report is a glossary of terms applicable to a classification system for coal resources and reserves. The purpose of this system is to provide a common yardstick for determining coal resources and reserves.

Jan 1, 1974

By Lloyd A. Morley, Robert Stefanko

Before going directly to the analysis, it would be good to summar¬ize explosion-proof container approval methods. Both Magison (52) and Short (84) state that in general practice, the systems are certified for: 1. a rugged enclosure able to withstand an internal explosion but not allow explosively hot gases to escape, and 2. maximum surface temperature, with equipment operating inside, that will not ignite the surrounding atmosphere. Also, testing insures that any material in contact with the container surface will not be ignited by a hot spot. Associated with the first practice, the enclosures are inspected for: 1. a safe flange gap width, 2. a pressure increase during ignition, and 3. an hydrostatic pressure withstand level. The hydrostatic pressure level is almost always determined by a meas¬ured ignition-pressure test and is usually applied to prove the mechan¬ical design to some safety factor. Consequently, explosion-proof enclosure testing includes temper¬ature, permissible flame gap, and pressure. Specifications and prev¬ious research also can be similarly separated even though some interre¬lation exists between the flame gap size and internal enclosure pressure during an explosion. The Schedule 2G Sections applicable to these subjects are: 1. 18.2 Definitions; 2. 18.6 Applications;

Jan 1, 1974

By James P. Bennett

The Bureau of Mines is investigating the acid resistance of ceramic materials to identify construction materials for emerging technology in chemical and metallurgical processes. Eight commercial ceramic materials, were evaluated: two red shale, two fireclay, one silicon carbide, one silica, one carbon, and one high-alumina. Samples were exposed to 10 wt pct H2S04 at 50° C and 10, 30, 50, 70, and 90 wt pct H2S04 at 90° C for time periods of 110 days. Statistically significant changes in cold crushing strength were observed in the silicon carbide and car-bon materials. Weight changes and the leach rate of Al, Ca. Fe. K, Mg, Na. Si, and Ti were also monitored. The most severe corrosion conditions were at 90° C and 30 to 50 wt pct H2S04 for the acidproof and at 10 wt pct H2S04 for the acid-resistant materials. The silica and the high-alumina materials were the most acid-resistant, followed by the higher density red shale and fireclay.

Jan 1, 1986

By Maria I. De Rosa

The U. S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (~300° C) and later (~400° C) combustion stages of chlorinated polyester-reinforced mine ventilation ducts could be predicted by a smoke particle characteristic, for the development of a test parameter. The experiments were conducted in an approximately 20-L furnace, at 14-min durations at set furnace temperatures of 2500 and 1,000° C, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were the hydrogen chloride (HCI), carbon monoxide (CO), carbon dioxide (C02), and oxygen (02) concentrations, furnace temperatures, the sample mass weight loss, the average smoke particle diameter (dg and average number and concentration (no), and the product of the average smoke particle diameter and concentration (dgno). Results show that the inverse of the smoke particle diameter-concentration product [(l/dgn0)], correlates directly and significantly with the primary gas toxicities evolved during both early (HCI) and later (CO) stages of combustion.

Jan 1, 1989

By Carlon S. Land

The Bureau of Mines investigated the influence of a free gas saturation on oil recovery by water drive. A digital computer was used to calculate the combined oil recovery from solution-gas drive to various states of depletion. Results of these calculations are compared and optimum conditions for the maximum oil recovery are found for various fluid-rock systems. For most of the fluid-rock systems, the calculations show an optimum gas saturation other than zero. Using fluid and rock properties as parameters, graphs are plotted showing the optimum gas saturation and increase in oil recovery brought about by the gas saturation. The effects of fluid properties and relative permeability on the optimum gas saturation are seen in these graphs. The graphs can be used as guides in connection with other considerations in determining the optimum time to start a waterflood. They should also be helpful in determining the MER of a water-drive reservoir. The effects of compressibility and solubility of the trapped gas saturation are investigated for select cases using a backward difference scheme to solve the partial differential equation of three-phase flow. From these calculations, it is observed that some benefit of a gas saturation remains for injection pressures up to 1.5 times the original bubble-point pressure.

Jan 1, 1974

By Brian G. White

The Coeur d'Alene Mining District of northern Idaho is remarkable for its number of large ore bodies and for the amount of its historical production of lead, zinc and silver (Fig. 1). Since veins were first discovered in 1884, more than 127 Mt (140 million st) of ore have been produced from narrow, high-grade veins. Mining continues at the Lucky Friday, Galena and Sunshine mines (Fig. 2). All have been in production for decades. At these mines, more efficient mining and exploration techniques have reduced costs while adding significant new reserves. Even the old Bunker Hill Mine, where ore was first found in 1875, continues operation on a limited basis, partly involving production of world-class pyromorphite specimens. Until recently, the Coeur Mine was also a profitable silver producer. Other large producers have included the Star-Morning, Hecla, Page, Standard-Mammoth, Hercules and Gold Hunter mines (Fig. 2). The first deposits were discovered by prospectors who spilled over from the Murray gold mining district, 24 km (15 miles) to the north. The Bunker Hill Mine was founded the year after the first veins were discovered. Bunker Hill has now operated for more than 100 years. Production includes 2.3 Mt (2.6 million st) of lead, 1.1 Mt (1.2 million st) of zinc and 4.1 kt (132 million oz) of silver. Total district production through 1996 (Springer, 1997) amounted to 7.3 Mt (8.1 million st) of lead, 3 Mt (3.3 million st) of zinc, and 34.5 kt (1.109 billion oz) of silver. This record establishes the district as the largest recorded producer of silver in the world, while also yielding major quantities of lead and zinc. Only Potosi, Bolivia, may have produced more silver, although records are unclear. Despite the district's longevity, historic production and current activity, the published literature on the district lags behind with regard to recent concepts of district geology. The most recent comprehensive US Geological Survey (USGS) bulletins (Hobbs et al., 1965; Fryklund, 1964) are dated. Much research in the last half century has been short-lived or geographically restricted because the district is large and its geology is complex - and even this research tends to remain unpublished. Thus, it has been difficult for in- [ ]

By O. M. Schaus

The following is a description of the methods employed at the Eureka-Asteroid mine, which is situated on the Gogebic range, at Ramsey, Mich. The mime is operated by the Castile Mining Co. under the direction of Oglebay Norton & Co. This paper has been prepared in accordance with an outline furbished by the United States Bureau of Mines, and in one of a series, on mining methods and costs covering the principal minim operations throughout the United States. ACKNOWLEDGMENTS The author acknowledges the assistance of the mining organization of the Castile Mining Co. in the preparation of this paper.

Jan 1, 1930

By Andrew B. Cecala

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36 and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 2010

By L. A. Panek, A. J. Barry, John A. McCormick

"INTRODUCTION During recent years, roof bolting has become widely accepted as a systematic method of supporting both coal- and metal-mine roofs. Today, over 2 million roof bolts are installed monthly. Most of the information on bolt installation procedure reported to date (1,2,3,4,5,6) 3/ has been obtained by trial and error by individual groups or operators. To insure good roof control, experience and field tests have indicated that roof bolts should be installed immediately after the exposure of new roof, and they should be preloaded enough to minimize sag of the roof over the opening. The question of the proper initial preload for roof bolts is under study, although it is a general practice to impose an initial load on a bolt of approximately 10,000 pounds. This created a problem of measuring bolt loads at installations in underground mines, which was partly solved by using a commercial-type torque wrench; a device that permits a direct reading of the torque applied to the nut on a roof-bolt assembly from which the corresponding load can be determined by referring to specifications furnished by the manufacturers. However, considerable apprehension was expressed regarding the accuracy of this measuring procedure because of variations in the manufacture of roof-bolting materials and the degree of care exercised in making bolt installations. In the process of loading a bolt, only a small part of the effort is expended in producing strain in the bolt - the larger part of the effort is used in overcoming frictional effects in the nut-bolt-washer assembly. These frictional effects are subject to many factors, such as condition of threads, type of lubrication, if any, the finish on the nut and bearing plate, and the alinement of the bearing plate on the bolt. The object of this investigation was to determine the accuracy with which the load developed in a slotted-type roof bolt installed in a conventional manner in shale or sandstone roof rock can be determined from the torque applied to the nut.This report is the first of a series relating to basic research in roof bolting in underground mines. A future report will cover results obtained using expansion-type bolts under similar conditions. Other reports will consider the efficiency of bolt anchorages, the long period stability of bolts, and the design of safe and efficient roof-bolting systems."

May 1, 1953

By d&apos, Kathleen J. Amico

THIS SUMMARY appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operatons at or near mines.

Jan 1, 1963

By T. E. Sterner

The Bureau of Mines investigated the use of a chromatographic gas analyzer in determining the concentration of combustion products in gas produced during field and laboratory thermal oil-recovery tests. Several parameters (carrier-gas flow, cell current, sample size, and temperature) known to affect quantitative analyses were studied using a commercially available dual-column, dual-detector chromatographic gas analyzer which had been modified to provide close control of these variables. The apparatus made possible a much closer control of air-and gas-injection rates and provided adequate data for performing material-balance calculations and for determining oxygen utilization during the laboratory and field combustion tests. The chromatographic analysis also aided materially in evaluating and measuring bypassing and gas travel times and in detecting high-permeability zones that were present in the reservoir.

Jan 1, 1965

By Charles F. Weber

Premature blasts of charges of explosives have caused many deaths in anthracite mines, and the causes of many of the blasts were not determined satisfactorily. Investigators often found fairly high potential differences between such metallic objects as rails, pipes, conveyor lines, or sheet-iron chutes in the working place where an accident had occurred. At one mine where a premature blast occurred in a rock tunnel, one workman was killed and two others were injured, and several days later a potential difference large enough to explode an electric squib was detected between the compressed-air pipe and the track rail; the voltage fluctuated and appeared to change with the movement of a locomotive. At another mine, a. workman was killed when a primed cartridge that he was about to load in a blast hole exploded in his hand. During the investigation, a potential difference was found between the conveyor line and the sheet-iron chute. During a 5-year Period, 61 fatalities and 771 nonfatal injuries were caused by explosives accidents in anthracite mines, and one of the chief causes of these accidents was premature blasts.

Jan 1, 1950

By R. Stefanko

The industrial hygiene and safety aspects with internal combustion engine in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. Mathematical models of the dilution and dispersion of diesel exhaust contaminants can be useful only if these models can be validated. In this research report, experiments that were specially designed for the above purpose are described. These experiments were conducted in the U.S. Bureau of Mines, Safety Research Coal Mine, in Bruceton, Pa. On the basis of this study, the data collected, and further review of available literature, it is concluded that mathematical models of dilution and dispersion are useful tools for mine ventilation planning. Additional objectives of this study about which conclusions and recommendations are reported here include: (a) evaluation of mine atmosphere contaminant monitoring systems; (b) optimum sampling site locations; (c) model sensitivity and error analyses; (d) computer coding of mathematical models; and (e) development of a diesel bibliography. While an extensive bibliography on diesels is provided in this report, Volume II of this final report has 511 references.

Jan 1, 1977