Search Documents

By Alim Gül, Güven Önal

"Recently, there have been some attemps on the treatment of low grade ores and old plant tailings due to the decrease in high grade ores and the increase in the metal consumption with increasing world population. Cost of mining and beneficiation of low grade ores become prohibitive since the costs of grinding before flotation make the process unfeasable. Therefore, preconcentration of these ores prior to flotation becomes more important. The concentration of ores preconcentrated in coarse sizes provides a decrease in investment costs as well as grinding and flotation costs. Additionally, the requirements of less space for tailing disposal and less reagent consumption are also important from the viewpoint of environmental considerations.In this study, ore sample containing 0.6 % Cu and taken from Küre-Asiköy ore body was used. Ores contained chalcopyrite and pyrite as main minerals and diabaz, quartz, chlorite and sericite as gang minerals.Samples were all crushed under 9 mm by considering the preliminary studies and float and sink experiments were carried out with the sample in the size range of –9+1 mm using different densities of heavy liquids. As a result of these tests, it was shown that 60 % of the material should be discarded as tailings with 0.1 % Cu content. By considering float and sink test results, the following experiments were performed by using heavy medium cyclone and jigs.As a result of heavy medium cyclone tests, which are conducted on the sample in size range of –9+1 mm, 57 % of the feed material was discarded as tailing with 0.08 % Cu content and 7 % Cu loss, while a concentrate containing 1.43 % Cu was produced with 93 % efficiency (Table 1). Jig tests were done with the samples in the size range. As a result of jig tests with –9+1 mm size group sample, approximately 46 % of feed material was discarded as tailings with 0.13 % Cu content and 10.6 % Cu loss, while a concentrate with 0.94 % Cu content was obtained (Table 2)."

Jan 1, 2003

By Buks Kruger

"After the milling and flotation of the platinum bearing ore, the flotation concentrate is electrically smelted in 6-in-line electric arc furnaces and the resulting furnace matte treated in Peirce Smith converters to remove the iron sulphide. The iron free (less than 1% Fe) converter matte is then granulated and sent to the Base Metals- and Precious Metals Refineries for further processing.During the smelting and converting processes two distinct gas streams are produced.The Peirce Smith converter off gas contains 4% - 9% SO2 which is treated in a conventional Sulphuric Acid Plant to produce sulphuric acid (H2SO4).The electric furnace off gas contains 0.9% SO2 and was (until September 2002) vented through a 91 meter high stack to atmosphere.Off gasses which contain less than 3% SO2 is difficult to handle and quite a few processes had been developed over the years to cope with this gas. A broad spectrum of process suppliers and technology approaches is available and the different technologies can be divided into a few main approaches i.e.Scrubbing of the off gas with an alkaline solution to produce an environmentally friendly and stable waste product which can be discharged onto a tailings dam or permanent landfill site.Physical absorption of the SO2 into a chemical solution to produce high quality chemically pure process chemicals.Catalytic reaction of SO2 with O2 to produce SO3 which is absorbed in water to produce sulphuric acid of less than 90% strength.In October 2002 Impala Platinum commissioned a Sulfacid Plant at its Smelter in Rustenburg which recovers the SO2 from the electric furnace off gasses into a weak sulphuric acid solution.The Sulfacid Plant technology is widely used in the paint pigment industry. This is, however, the first application of the technology on electric furnace off gas.The furnace off gasses contains flue dust which is removed in electrostatic precipitators. The gas exiting the precipitators normally still contains between 40 mg/Nm3 and 60 mg/Nm3 dust and passes through a quench-scrubber before entering the reactors. The quench-scrubber cools the electric furnace offgas down from ± 200 °C to 60 °C and act as a final dust removal stage."

Jan 1, 2003

By F. L. Mentg

The utilization of acid leaching tailings was studied. It is obvious that the Fe in acid leaching tailings can be leached into solutions as Fe2+. In this paper, the influence of conditions, including the concentration of ferrous sulfate, pH, temperature and velocity of air flow was investigated. The optimum conditions for preparing seed crystal are as follows: the concentration of ferrous sulfate is 20 g/L; pH is 9.5~10; reaction temperature is 10~20?; velocity of air flow is 0.4m3/h. The optimum conditions for preparing iron oxide red are as follows: the concentration of ferrous sulfate is 5 g/L; reaction temperature is 80~85?; velocity of air flow is 0.13m3/h. At last, the product of iron oxide red could be prepared by ammonia method.

Jan 1, 2014

By Anatoly N. Vinogradov, Vyacheslav A. Tsukerman

The North-West Russia for 70 years is one the main producers of Cu, Ni, Co, Al, P, REE, Zr, Ti, Ta, Nb, Fe ores and other minerals in the Europe. The largest mining companies locates in the Murmansk region, and they extracts about 100 mln. tons of ores and damps up to 250 mln. tons of waste annually. Nevertheless an environmental situation in the region is stable due to rational management and treatment of wastes on a base of the Noosphere Concept for Nature-using suggested by Vladimir Vernadsky. The Concept was performed practically in the Fersman’ scheme of “non-waste mining and metallurgical complex”, published in the monograph “Minerals of the Kola Peninsula: current status – analyses – prognoses” (1941) and served till now as a sort of “Bible” for industry managers lightening a strategy for an industrial “trophic chain”. The recent status of this scheme is shown on the picture below, and one can see that our concept is coincide with modern ideology known as the “Industrial Ecology”. Moving along this mainstream in the Kola Peninsula since 1929, when the first mining company “Apatit” was established, we provided the water close circuit in mineral dressing plants, hydrometallurgical treatment of slag and tailings, productions of building materials and adsorbents of wastes. The innovation set of technologies designed by the Kola Science Centre allow recently to involve tailing damps in re-exploitation as the technogenic deposits of valuable raw materials for fertilizers, tanning and cleaning agents, pigments, concretes and etc.

Jan 1, 2003

By Marina Nicolova, Irena Spasova, Plamen Georgiev, Stoyan Groudev

Different strains of "silicate" bacteria were used to improve the quality of kaolin by different ways of treatment. All strains formed large slimy capsules consisting of exopolysaccharides and were related to different species of the genus Bacillus, mainly to B. circulans and B. mucilaginosus. It was found that even a short contact of some hours of well developed cultures of these bacteria resulted in improvement of the bending strength and the other ceramic properties of the kaolin. The improvement was connected with the action of some secreted microbial metabolites such as soluble heteropolysccharides, monosugars and organic acids. The best results were achieved by continuous cultivation of bacteria in the presence of kaolin with a high relative humidity and subjected to periodic stirring.

Jan 1, 2014

By Stefan Mutz, Thomas Pretz, Jörg Julius, Frank Hilbk-Kortenbruck, Aachen, Hartmut Harbeck

"The annual global production of primary aluminium was about 22 million tons in the year 2000. This represents the second largest production rate in the world market after steel. Experts are predicting that the global demand for aluminium will rise in the near future.In contrast to other metals such as copper, the recycling of aluminium is considered relatively difficult. There are two main alloying groups, namely cast and wrought. In the case of aluminium it is important that the constituents within the scrap aluminium to be smelted are clearly identified. Within the secondary remelting process alloying does take place, but a removal of unwanted metal constituents is problematic. Therefore mixed aluminium scrap (not genuine in-house collected material) can only be used to produce cast aluminium. Thus, in other words a down-cycling of wrought (extrusions and rolled) products occurs. However, in spite of these difficulties there is an increasing trend to produce aluminium from secondary scrap (approx. 35% in Germany). Similar trends have been identified in the USA and other industrialised countries. This development is mainly caused by the high energy consumption for the production of aluminium from bauxite. Producing aluminium from scrap is saving about 95 % of the energy in comparison to the processing of primary raw materials.An improvement in sorting technology is necessary to separate wrought and cast alloys of aluminium as the absolute amount of recovery from old scrap is higher than the demand for cast.This contribution presents some alternative methods, utilizing automatic picking technologies, which will be used to separate secondary aluminium in the future. During the recent years, some major progresses have been made in automatic picking technologies for different applications in the processing of primary and secondary materials.For the sorting of aluminium scrap a special additional sensor will be necessary. The best detection will ultimately be based on online elemental analysis of single particles. First investigations in the field of laser based systems for these applications have already been performed several years ago. One of the laser based techniques is the laserinduced breakdown spectrometry (LIBS)."

Jan 1, 2003

By M. H. Moys, M. M. Bwalya

The use of the Discrete Element Method (DEM) to simulate the interaction of particles in dynamic environments is growing rapidly. This technique is also being applied in the study of milling extensively. However, to date more focus has been on the validation of the model. In spite of the advantages of the detailed information that is available from the simulator, appropriate application of this information remains a daunting task. In this paper a technique that combines particle breakage probability data with the energy spectra generated from the DEM is discussed.

Jan 1, 2003

By Stuart Simpson

The biggest environmental challenge in mining is the management of mine tailings. Deep----sea tailings placement (DTSP) is practiced where the environmental impacts are predicted to be less than the impacts of tailings storage facilities on land. However, DSTP is often highly controversial owing to the challenges in assessing the impacts in deep water environments and potential long----term impacts beyond the proposed tailings footprint. It is well recognized that total contaminant concentrations are often poor predictors of the risk posed by contaminants in sediments. Metals within tailings are mostly present in highly mineralised forms that are typically much less bioavailable to organisms when compared to other common anthropogenic metals. Thus while metal concentrations in tailings can often appear alarmingly high, when compared to sediment quality guidelines (SQGs) used for assessing common urban and industrial impacts, the bioavailability is typically low. Although now well----embedded within risk----based sediment quality assessment frameworks, contaminant bioavailability is still often overlooked in the management of contaminated sediments. In this presentation, we assess and demonstrate the low bioavailability and chronic ecotoxicology of mineral----rich tailings to two benthic invertebrates, recognized for their sensitivity to metals: impairment of reproduction of the amphipod, Melita plumulosa, and the harpacticoid copepod, Nitocra spinipes. We demonstrate that the metal exposure from mine tailings is low when total concentrations are considered, and that the dose to the organism and toxic response observed is highly dependent on contaminant bioavailability. We discuss a range of approaches for the effective incorporation of metal bioavailability when applying SQGs or setting site-specific management limits for mine tailings in marine environments. While proposed DSTP operations require a high level of environmental scrutiny and monitoring during operation and post-closure, environmentally sustainable operations may be achieved when the bioavailable forms of metals within tailings remain below suitable management limits.

Jan 1, 2014

By Willis Forsling, Prabhakar Swarna, Hanumantha Rao Kota

"The solubility of wollastonite and its Hallimond flotation behavior as a function of dodecylamine concentration and pH are examined. The flotation response is characterized by adsorption and surface energy in the presence of amine. The methods of UV-Visible and FT-IR spectroscopy for adsorption and sessile-drop contact angle for surface energy estimation are employed.The results of wollastonite dissolution clearly showed its non uniform dissolution. The surfaces are depleted with calcium ions and became rich in silicon within 10 min of flotation time. Maximum flotation of wollastonite corresponds to a half monolayer coverage of amine, which is substantiated by the surface energy parameters as shown in figure 1."

Jan 1, 2003

By Ashton M. Swartbooi, Robert van Hille, Alison E. Lewis

"Nickel production by precipitation using hydrogen reduction generates an ammonium sulphate solution containing approximately 2g/L of nickel, and 1g/L of cobalt as an impurity of the process. Sulphide precipitation is an effective method for heavy metal removal, especially when compared to hydroxide processes: metals can be removed from solution at relatively low pH levels, small quantities of sludge are formed, and due to the high reactivity of sulphides the reactor retention time is reduced. However, the low solubility of sulphide species can lead to spontaneous nucleation of fines (due to higher supersaturation levels which are difficult to separate from solution, leading to reduced process efficiency. Using a fluidised bed reactor, fines formation can be minimised as the pellets provide a large surface area and promote heterogeneous nucleation.A synthetic nickel-cobalt ammonium sulphate solution was reacted with two forms of sulphide reagent: (a) a liquid sulphide solution and (b) gaseous hydrogen sulphide. A range of factors (including pH, reagent concentrations, metal to sulphide molar ratio, flow rates and recirculation rates) influencing the efficiency of the precipitation reaction have been studied. The efficiency of the precipitation reaction was measured using both metal recovery and fines formation as indicators.Figure 1 shows the effect of decreasing the metal:sulphide ratio (at constant SS = 2.725e+17), on the metal removal for liquid sulphide. By decreasing the metal:sulphide ratio, up to 99% removal of both nickel and cobalt could be achieved.These results also indicate that the precipitates that formed were polysulphides, since no sulphide was present in solution after the experiment. This would also indicate that a lower metal:sulphide ratio would be more favourable. However, decreasing this ratio (at constant metal concentrations) would lead to an increase in the fines concentration, because of increased supersaturation levels induced by the higher sulphide concentrations. To decrease the supersaturation, dilute solutions of either reagent would be employed."

Jan 1, 2003

By Cheng Gan, Gui Xiahui, Li Shulei, Cao Yijun, Liu Jiongtian, Wu Lun

Flotation rate constant is an essential parameter in the flotation process. The fine coal sample utilized in this investigation is anthracite from the Shenhuo mine in eastern China. Fine coal flotation rate tests were conducted to compare the flotation rate constant at constant power input with that at gradually increasing power input. Results indicate that the flotation rate constant decreases with the flotation process and increases as the flotation energy is increased. In addition, the flotation rate constant is close to the maximum value. The increasing trend of the flotation rate constant gradually slows down as the flotation energy input increases.

Jan 1, 2014

By Wu Tao, Lu Shijie, Xia Xiaoou, Zhang Ming

The impeller and stator are the most important components that can significantly influence the performance of flotation cells directly. The performance of the impeller and stator of KYF flotation cell is revealed by CFD (Computational Fluid Dynamic) simulation in this paper. A method of obtaining the circulation volume is proposed. The circulation volume is proportional to third power of impeller diameter. And the circulation volume increases linearly with the increasing of the speed. CFD simulation can draw the conclusions that there is a proportional relationship between power consumption, third power of speed and fifth power of impeller diameter. CFD prediction results agree with the theoretical formula. The difference between the forward and backward impeller is analysed in the paper. The circulation volume of the backward impeller is obviously larger than that of the forward impeller under the same condition, but power consumption of the backward impeller is lower. It is demonstrated that the impeller and stator system of KYF flotation cell is an efficient and reasonable stirring mechanism. CFD simulation could be reliably used in flotation cell design and optimization.

Jan 1, 2014

By Nóra Schreithofer, Kari Heiskanen

"INTRODUCTIONThe knowledge of the adhesion forces between particles and bubbles is of key importance in the improvement of flotation models. The development of the Colloidal Interaction Force Measurement Apparatus (CIFMA) opened the possibility to quantify the adhesion forces between particles and bubbles. The aim of this study was to examine the effect of three main variables: the approach velocity, the loading force and the loading time on the adhesion force between an air bubble and a hydrophobized silica particle."

Jan 1, 2003

By Williams Calderon, César Arredondo, Gonzalo Montes-Atenas

The quality of final concentrate in froth flotation circuits is largely dictated by the correct implementation of the froth washing operation in flotation cleaning stages, which are commonly installed in column flotation cells. In flotation plants, this aspect has been largely overlooked and the froth washing is restricted to the use of perforated piping through which process water flows producing a similar effect to that observed in "fountains": jet created with low energy crosses the froth phase washing out entrained particles as well as particles weakly attached to bubbles. The aim of this research study is to assess the efficiency of traditional froth washing systems theoretically and experimentally. A theoretical model was implemented using Fluent® software where a jet of variable speed was introduced in a continuous soft matter phase with physical properties similar to those observed in a froth phase in wet and dry conditions. In addition, a simple experimental protocol was designed to validate the model. It was found that the water process jet-like flow influences the behavior of 2 to 3 times the equivalent volume in the froth phase. Such influence zone is dramatically reduced as the froth phase becomes drier. These results were confirmed by the experimental findings indicating that a better froth washing technologies must be assessed and implemented. Some aspects of the ideal froth washing system are derived and discussed in details.

Jan 1, 2014

By G. S. Hansford, G. E. Searby

The rate of bioleaching of pyrite at 70ºC by a thermophilic archaeal culture was measured as a function of the solution redox potential by the staged addition of pyrite to a batch system. The results were compared to the rate of ferrous iron oxidation over the same potential range to determine the applicability of the multi-sub-process leaching mechanism developed for mesophilic bioleach systems.

Jan 1, 2003

By K. A. Natarajan

"Interaction with microorganisms results in significant surface chemical changes on minerals. For example, chemolithotrophs such as Thiobacillus ferrooxidans and Thiobacillus thiooxidans significantly alter the surface chemistry of several sulfide minerals such as pyrite, chalcopyrite, sphalerite and galena. Heterotrophic bacteria such as Bacillus sp. could alter the electrokinetic properties of oxide minerals such as hematite, alumina, silica, kaolinite and calcite. Microbe-mineral interactions could thus be beneficially utilised in mineral beneficiation as different from bioleaching. Microbially induced mineral beneficiation unlike bioleaching deals with interfacial phenomena at mineral-solution-bacteria interfaces and surface chemical changes are brought about at very rapid rates amounting to a few minutes resulting in mineral separations in an aqueous medium.In this paper, the role of acidophilic chemolithotrophs such as Thiobacillus thiooxidans and neutrophilic heterotrophs such as Bacillus polymyxa in the beneficiation of sulfide and oxide minerals is illustrated. Mechanisms of bacterial attachment on various sulfide and oxide minerals are outlined with respect to the influence of bacterial interaction in bringing about mineral surface hydrophobicity or hydrophilicity. The role of bacterial cells as well as metabolic products such as bioproteins and exopolysaccharides in significantly altering the surface chemistry of sulfide minerals such as sphalerite and galena and oxides such as hematite, alumina, silica and calcite is discussed with probable mechanisms. Possibilities of generating mineralspecific bioreagents are outlined with respect to bacterial adaptation to mineral substrates."

Jan 1, 2003

By P. Somasundaran, Tarun Bhambhani, D. R. Nagaraj, P. Patra

"Certain non-sulfide gangue minerals are known to have a detrimental impact on flotation performance. When present in large amounts, they can negatively affect recoveries, grades and throughput at current operations, and dictate the viability and economics of a greenfield project. While the problem has been investigated for a long period of time, a scientific understanding of the mechanisms by which these minerals affect performance has not been obtained, and no acceptable solutions have been developed. This study focused on the role of physical aspects (e.g. shape, size and morphology) of these minerals as the underlying factors for poor performance. Flotation tests were conducted using model mineral systems to understand the impact of one phyllosilicate mineral (muscovite) on flotation kinetics, recoveries and grades. The study reveals that there is minimal impact on flotation kinetics, no impact on recoveries, but a very strong detrimental impact on concentrate grade. The traditional mechanisms of transport such as true flotation and entrainment are not sufficient in describing the extent of transport. The transport is attributed to the unique platy morphology of muscovite, which allows for action of buoyancy forces. Data also shows that the muscovite transport to the froth phase depends on particle size; coarser sized muscovite (100-150@) report to the froth phase in much larger amounts than medium sized muscovite (50-100@). At finer size fractions (<50@) the transport is also increased, and this is likely due to entrainment."

Jan 1, 2014

By G. Merazchiev

In the selection of copper ? molybdenum concentrates with the use of reagents containing sulfide ion ? sodium sulfide, sodium hydrosulfide etc for depression of copper minerals and pyrites, big part of depressor is oxidized by oxygen, which is dissolving in pulp during aeration with air in flotation machines and it is expended unproductively. This is the main reason for the big expenditures of depressor, reaching up 15~20 kg/t collective concentrate and the high exploitation expenditures for the copper ? molybdenum selection. Effective direction for lowering expenditure of depressor and increasing of the technical ? economical effectiveness of moly production is the conducting of the selection in nitrogen medium. In the paper are shown the results, obtained by applying of this direction in selection of collective copper ? molybdenum concentrate from the porphyry copper deposit ?Ellatzite? ? Bulgaria, in which the ratio Mo:Cu is over 1:120. In laboratory conditions, through comparative experiments in medium of air and nitrogen are defined: expenditure and initial concentration of NaHS in pulp for effective depression of copper minerals and pyrites; kinetics of flotation process of molybdenite; influence of pulp density; emf (negative milivolts) of pulp and the expenditure of nitrogen on tech-nological indexes of molybdenum flotation. When working in nitrogen medium decrease of NaHS in rougher molybdenum flotation from 40% to 45% is settled. When nitrogen is also fed in cleaner stages, the total expenditure of depressor is lowered by 64%. The quality of end molybdenum con-centrate is raised with over 5%. On the ground of the results of laboratory studies and of world practice data, an industrial installation for selection of copper ? molybdenum concentrate in nitrogen medium in Wemco inert ? gas machines.

Jan 1, 2014

By D. Pienaar, B. McFadzean, T. Jordaan

"Dithiophosphate (DTP) collectors have the lowest affinity for sulfide mineral surfaces compared to other common sulfide mineral collectors, such as xanthates and dithiocarbamates. In some cases it has been found that DTP does not adsorb onto the mineral surface at all and yet increases in recoveries and grades are noticed with the addition of DTP. Many studies have investigated the interactive effects of collector mixtures. However, there have been relatively few studies on the interactive effects between frother molecules and collectors. This study investigates the interactions between different types of frothers and sodium diethyl dithiophosphate.The study found that there were large increases in pyrite and galena microflotation recoveries at both pH4 and pH9 when DTP was mixed with small amounts of frother at a constant bubble size, showing that these increases were neither mineral-specific nor pH-specific. The same effect was not present when xanthate was used as a collector. The increases in recovery when using the DTP-frother mixture were similar irrespective of the type of alcohol or polypropylene glycol frother that was used. In an attempt to distinguish the mechanism of enhanced flotation recovery, various supplementary experiments were performed. It was found through adsorption experiments that no DTP was adsorbing on to the mineral surface. Therefore, interactions at the air-water interface were performed. Surface tension and critical coalescence concentration tests showed that, while DTP is a weak surfactant at the air-water interface, it does not have a synergistic effect in the presence of frother. DTP-frother mixtures do, however, show interactions in the froth phase, indicating an interaction in the thin films. It is proposed that there is a DTP-frother interaction on the bubble surface that enhances the rate of film thinning at the 3-phase bubble-particle contact."

Jan 1, 2018

By Choi Sang-Ken, Chung Hun-Saeng, Kim Byoung-Gon, Park Chong-Lyuck

Fine grinding of crystalline graphite was conducted using a dry attrition mill with a vacuum system to investigate the characteristics of size reduction. Low pressure and high temperature conditions in the grinding mill were found to greatly improve the efficiency of the size reduction of graphite. Natural flaky graphite of .100 mesh was ground into sub-micron sizes, then over 90% of the product were able to be reduced below 1?without disrupting their crystallinity in a short period of time. Reducing the atmospheric pressure in the grinding environment promotes the removal of chemical species such as oxygen and water molecules adsorbed on the graphite particle, resulting in effective size reduction while maintaining the crystallinity of graphite.

Jan 1, 2003