Search Documents

By S. P. Das

Tumbling mill is an important unit operation in a mineral processing industry whose operation needs to be understood to make it an energy efficient unit. One of the important mill parameters is the impact spectra generated by collision of the moving charge mass on the mill shell. This process also generates mechanical vibration on the mill shell and propagates to the plumber block of the mill. In this work, we tried to understand the impact spectra by using different minerals such as Banded Hematite Quartzite (BHQ), Hematite and Quartz as mill feed of a semi-autogenous (SAG) mill. The said mill is of 1000 mm diameter and fitted with a force sensor on the mill shell and a vibration sensor on the plumber block. The analysis of the impact spectra was done by taking into consideration the peak impact force above a certain threshold value. It clearly shows that the impact force decreases as the particle size become finer irrespective of the mill feed material. This can be used as an effective tool by the mill operators to have an understanding of the mill product size reduction. The mechanical vibration tapped by a tri-axial accelerometer was analyzed by power spectral density analysis. The vibration signal analysis shows the variation in the power spectrum magnitude both at lower and higher frequency. It also shows inconsistency in case of BHQ where it shows a significant decrease in vibration at lower frequency and increase in vibration at higher frequency. Therefore, the impact spectra analysis is a better method compared to vibration analysis in understanding the mill product size reduction.

Sep 1, 2012

By Shuji Owada, Mayumi Ito, Takehiko Nishimura, Toru Yamashita, Sadayuki Shinozaki, Takashi Ando, Tomoe Ota

Electrical disintegration (ED) was applied to Nantun coal (China) in order to improve liberation of coal substance for the pretreatment of producing “Hyper Coal” of which the combustion gas was planning to inject directly to turbine for power generation. It has been found that many cracks generated in the ED were existent at phase boundaries with mineral matters and liberation of coal substance became much higher than that in mechanical comminution methods such as roll crusher. Since the ED occurred more easily (with lower voltage applied) for the coals of higher mineral content, it is considered that this method could make a better contribution especially to comminute middling coals. We also found that the ED technique could apply not only single particles but also to coal particles assemblage, keeping almost the same or higher disintegration efficiency. In the mineral matters, Si and Al components were preferentially well liberated by the ED.

Jan 1, 2003

By Tasuma Suzuki

Electrokinetic/permeable reactive barrier system is a promising in situ soil and ground water remediation technique to reduce toxic NO3- into less toxic NH4+. Using granular zero-valent iron (Fe0) as a reductant, the first objective of this study was to investigate the influence of the solid-liquid ratio and aqueouspHon NO3- reduction. The results obtained from a series of batch experiments showed that NO3- reduction was enhanced by either increasing solid-liquid ratio or decreasing aqueous pH. Based on insights obtained from batch experiments, the second objective of this study was set to design the remediation conditions of the electrokinetic/Fe0permeable reactive barrier system to maximize the NO3- reduction efficiency. Experimental results showed that the effectiveness of the system strongly depended on the Fe0 percentage in the reactive barrier, the pH in the anode reservoir, and the applied voltage, which were consistent with the results obtained from batch experiments. Under optimized treatment conditions, nearly 100 % NO3-was reduced into NH4+ in the permeable reactive barrier and collected in the cathode reservoir. Insights obtained from this study provided fundamental information on roles each of remediation design parameters plays, and will be useful to optimize the remediation conditions. Keywords: electrokinetic remediation, permeable reactive barrier, zero-valent iron, nitrate

Sep 1, 2012

By K. Hori

In this study, the determination of optimal conditions for jig separation has been investigated with a TACUB jig separator. The TACUB jig, from which a Batac jig originated, is a useful gravity separator that is effective to separate crushed solid wastes as well as coarse ores. A mixture of crushed polyethylene (specific gravity 1.3) and polyvinyl chloride (specific gravity 1.5) was separated by a batch TACUB jig by varying the frequency (wavelength) and the amplitude (pulse stroke length). It was found that the sample particle layer in the separation chamber was fluidized without turbulence by the rising water pulse resulting in the separation. However, a too strong water pulse reduced the efficiency of the separation of the particles. The results indicate that the specific velocity of the rising water is necessary to fluidize the particle layer without turbulence to separate the particles. The expansion ratios of the thickness of the particle layer in rising flows were measured in a cylindrical column. The pressure losses by the particle layer were calculated from the expansion ratios and the velocity of the rising flows by Ergun?s equation. The curve of the pressure loss vs. the velocity of rising flow showed a maximum point corresponded to the point of fluidization. The velocity of a rising flow on the point of fluidization provided the optimal separation condition.

Jan 1, 2014

By Alexey P. Tatarinov

Under modern economic conditions in Russia, gold heap leaching is the most effective way of investing into gold-mining industry. Gold is recoverable from small-size deposits, low-grade ores from oxidation zone, cut-off grades, and overburden rocks using heap leaching. This technology is cost-effective and allows a saleable metal to be obtained within the first year of operation. The investments for heap leaching are lower than those of for a traditional plant technology. Production cost per one gram of Au is 5-7 times lower than that of during a plant flow sheet. A seasonal development of mines can be possible. With reference to this, heap leaching resembles the technology of placer deposits development. One of the major advantages of heap leaching is the form of the product. Gold can be obtained as dissolved in a clarified PLS, which allows the further quick treatment. The amenability of ores to heap leaching depends on their mineralogical composition. Oxidized porous ores with a good access of a lixiviant to valuable particles can be treated without pre-crushing. Clayish minerals are often found in oxidized ores with free gold. In order to build ground for heap, several major methods combined with various pad materials are used. These methods have been used at many plants and are reliable. The development of heap leaching technology for gold ores for the deposits from Yakutia, Zabaikalsky region, Primorye region, Uzbekistan, Tadjikistan, and Kazakhstan began in the 70s. However, it has been commercially used only since 1990. The first heap leach plants were built and commissioned in the USSR in 1991 at Vassilkovsloye deposit (Kazakhstan) and at Maiskoye deposit in Russia in 1994. Pilot plant testing was conducted in 1996 using ores from Kuranakh ore field, deposits Phiskulturnaya-Kholodnaya and Lopukhovskoye from the Aldan region. After the first successful commissioning of heap leaching plant in Russia, this technology has been commercially applied for deposits. Every year 1-2 heap-leaching plants were commissioned. More than 30 heap-leaching plants have been commissioned both in Russia and in the former Soviet Union using technologies developed by IRGIREDMET. Keywords: cyanide leaching, heap leaching, ore, percolation, solutions, lime technology

Sep 1, 2012

By Leon Lorenzen, Nursen Guresin, Harald Muller

The development of mining projects from discovery, exploration to actual production is a complex and time consuming process. Often poor process plant performance can be attributed to the use of non-representative samples and inadequate and/or unsuitable metallurgical test work when designing flow sheets during project feasibility study stages and specifying process equipment. Samples not representing the ore deposit and inadequate test work may lead to increased project development costs, since expensive test work and engineering may have to be repeated. It should be noted that for higher level engineering studies, larger scale test work is recommended and is a requirement for feasibility level studies. This would apply even if the technology is considered mature and well proven, as each ore body may have its own unique characteristics that, if untested at a larger scale, could result in significant design shortcomings, which will have to be rectified at later stages of the project, usually at significant additional costs

Jan 1, 2014

By Jan Cilliers

The demand for minerals has never been higher. Moreover, the rate at which this demand is growing is unprecedented, and expansions and new mines will be required to fulfill these growing needs. This, in turn requires a skilled engineering workforce that can develop and operate minerals extraction processes to utilise effectively more complex ores. The International Mineral Processing Council (IMPC) has established a Commission on Mineral Processing Education to consider the global challenge of ensuring an adequate supply of well-trained mineral processing engineers. The Commission has, for the past four years, been collecting international information of the recent mineral process engineering supply position and with a view into the near future. The data collected by the international Commission members are as follows: ? Undergraduate student numbers in minerals engineering ? A breakdown of their male/female ratio ? The fraction of the students from each course that enter the minerals industry ? Teaching staff numbers and age profile This data has been collated and analysed, and the findings are presented. It is clear from the analysis that the supply situation is very different in different regions of the world, and that great opportunities exist for targeted recruitment into the industry to meet the future talent demand. Further, an attempt at correlate the supply of minerals engineers based on the local mineral production rate is shown, which shows that there are clear outliers.

Sep 1, 2012

By I. A. Makalin, V. N. Yakovlev, S. V. Imangulov, I. V. Zyryanov

"The presented studies aimed at solving the problem of recovery of low-luminescent diamonds, which are not recovered using X-ray luminescence method of processing of diamond-bearing ore. The purpose of the studies is the determination of possibility and feasibility of recovery of such crystals using dual-energy X-ray transmission separation technology. In preparation for studies methods were developed for testing technical and process parameters of XRT-400 Aliud GmbH (Germany) sorter, manufactured according to design specifications of Yakutniproalmaz Institute, and XRT/D TOMRA Sorting Solutions GmbH (Germany) sorter, designed for processing of -50+5 mm ore, as well as RGS-1M, RGS-2 X-ray sorters, developed by JSC NPP Bourevestnik (St. Petersburg) in cooperation with Yakutniproalmaz Institute, for material size of -6+3 mm. In 2018, in-process tests of RGS-OD-3 X-ray sorter prototype on material size of -3+1 mm are scheduled. Studies to determine the content of low-luminescent diamonds and feasibility of their recovery using XRT-400 and XRT/D sorters at the Processing Plant #3 of Mirny Mining and Processing Division (MPD) were carried out. The results of the studies confirmed presence of such diamonds and possibility of their recovery using the dual-energy X-ray transmission method. In-process tests of RGS-2 X-ray graphic sorter were carried out at the Processing Plant #16 of Nyurba MPD. According to the results of sampling of RGS-2 sorter separation products, the recovery of -6+3 mm sized diamonds from tailings of X-ray luminescence sorters was achieved at the level of 96%, while the diamonds recovery was 98.5% in value terms, the concentrate yield was 0.1%. In-process tests of RGS-1M sorters at final recovery of the grease separation concentrate at the Processing Plant #3 of Mirny Division were carried out. Recovery of low-luminescent -6+2 mm sized diamonds by RGS-1M sorter amounted to 92.4% for single operation, and with the double control operation reached 99%. As a result, -6+2 mm sized base product recovery increased by 0.2%."

Jan 1, 2018

By Y. M. Zhu, G. C. Gong

"The influences of citric acid (CA) on the flotation behavior of cassiterite using styrene phosphonic acid (SPA) as the collector were studied via single mineral flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations in this paper. The results of single mineral flotation tests revealed under the conditions that pH=4 and the dosage of SPA 100 mg/L, the recovery of cassiterite reached 76.78%. The addition of 20 mg/L AC decreased the recovery by 12.42% at pH=4. Contact angle measurements demonstrated the adsorption of CA prior to SPA made the cassiterite more hydrophilic. The results of zeta potential determinations and solution chemistry calculations indicated the chemisorption of C6H7O7- and C6H6O72- filled parts of the Sn site on cassiterite surface and prevented the SPA from getting adsorbed. The hydrophilic effect of AC was stronger than the hydrophobic effect of SPA and the flotation of cassiterite was crippled. INTRODUCTION Tin is an important metal which is widely used in medical instruments, marine engineering materials, electronic and electrical devices, welding, weapon manufacturing and organotin compounds industries (Angadi et al., 2015). Cassiterite is the only mineral from which the tin can be extracted, thus it is of great importance to efficiently exploit the cassiterite mineral. Flotation is an indispensable method for the recovery of cassiterite (Li et al., 2015). However, cassiterite is usually in association with many other gangue minerals which are of similar floatability, such as quartz, calcite, fluorite, iron oxide, wolframite, scheelite and tourmaline (Sreevinas, 1997). So some modifiers are necessary in the cassiterite flotation process. The amounts of the modifiers used in the flotation must be judicious and the overmuch modifiers may cripple the recovery of cassiterite (Parsonage et al., 1987). Nevertheless, the research about the effects of the modifiers on the flotation behavior of cassiterite has been rarely reported. In this paper, the influences of citric acid (CA) on the flotation of cassiterite using styrene phosphonic acid (SPA) as the collector were investigated by flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations."

Jan 1, 2018

By Arkady Senchenko

The paper deals with the problem of refractory gold-containing material processing. It is observed that all traditional methods for liberation of fine gold from this type of products are characterized by a number of essential disadvantages, where the main ones are ? considerable expenses for ore processing and big environmental impact. As an alternative to the existing methods there is considered a gold liberation method, which is based on the combination of ultra fine grinding process with the consequent atmospheric oxidation. The theoretical justification of atmospheric oxidation was carried out, in the result of this the mechanism and the degree of sulphide minerals? oxidation was found out, the dependence of gold dissolution speed on the slurry content in liquid phase produced by grinding and oxidation was identified. The experimental data and results of pilot-plant testing are given and the most effective grinding and atmospheric oxidation mode is selected on this basis. The performed complex of research works allowed us to use the provided technology at the gold processing plant having capacity of 8 mln. tons of ore per year. The questions, problems, advantages and disadvantages of atmospheric oxidation technology for refractory gold-containing concentrates are considered in this paper. Keywords: refractory gold-containing material processing, gold liberation method, cyanidation

Sep 1, 2012

By Brochot. Stephane, Manuel Gonzalez Fernandez

"HPGR (High-Pressure Grinding Rolls) is widely used today for grinding of various kinds of ores such as iron ore or base and precious metal ores. It can be used as first stage of grinding replacing tertiary crusher and SAG mill, but also as regrinding stage to enhance mineral liberation. In addition to better energy efficiency, the advantage of HPGR is to produce much more internal particle fractures allowing faster leaching as it has been demonstrated for some gold ores. This grinding mode of compression and fracture generation also promotes mineral liberation without overgrinding. Mineral processing modelling and simulation associated to detailed ore characterization constitute a powerful tool for plant design and optimization. The mathematical models of the units of operations (grinding and separation) have to reproduce the mineral deportment for which the mineral liberation plays a central role. The present paper is focused on the HPGR modelling with the objective of plant optimization or advanced design from pilot plant tests. The traditional approach of the population balance linked to the energy dissipation and the residence time distribution is generalized in association with a mineral liberation model. The effect of the specific HPGR breakage matrix and grinding function on the mineral liberation rate is discussed and compared to the tumbling mill. The implementation of this mathematical model into a plant simulation tool is illustrated by the example of the optimization of an iron ore concentrator."

Jan 1, 2014

By A. A. Novoselov, U. Kelm

"Large volumes of mine tailings accumulated in surroundings of porphyry copper deposits represent a growing threat to environment. They contain significant concentrations of toxic metal and metalloids which can contaminate river runoff, ground waters or can be transported by wind. Both extreme pH of fluids in tailings impoundments and high surface areas of processed mineral grains provide their increased reactivity. As a result, during only a few decades, As, Cu, and Mo can be mobilized, redistributed through the tailing column and accumulated through post-deposition leaching, evaporation and contamination with natural fluids. Those processes are reflected in the forming of secondary minerals. Gypsum, Fe oxides/hydroxides, efflorescent salts and clay minerals are typical alteration products in tailings. Here we present the results of reactive transport simulations implemented on the base of PHREEQC and SUTRA codes. The one-dimension model emulates the mass balance between rainfall, evaporation and subsurface runoff, the kinetically- and thermodynamically-driven dissolution of tailing minerals, advective and diffusive transport of tailing fluids, and precipitation of secondary phases. A typical tailing column is composed of four unequal layers with predominance of (i) evaporation, (ii) secondary mineralization above, (iii) below water table, and (iv) near the bottom of dump. Those horizons are characterized by contrasting pH, chemical composition and bulk mineralization of pore fluids, distinct accessibility of atmospheric oxygen and, as a consequence, distinct intensity of sulfide oxidation. The modeling and its verification on Chilean tailings impoundments reveal the complexity and high rates of secondary mineralization. The accumulation of toxic alteration products is controlled by fluid transport through the tailing column induced by both rainfall/evaporation and exchange with subsurface runoff. The geochemical modeling is a powerful approach which allows comparing the processes in tailing deposits produced by distinct flotation regimes and providing the long-term predictions of their environmental impact as well as identifying sectors of tailings for possible re-processing."

Jan 1, 2018

By Herman Mendoza, Luisa Ciriaco

An investigation of the seeding mechanism using heterocoagulation and the Derjaguin - Landau - Verwey - Overbeek (DLVO) theory of two pure minerals is the objective of this study. The seed was silica with modal diameters of 4.529 µm (fine particles) and 5.216 µm (coarse particles) and the test powder was hematite with a modal diameter of 0.883 µm. Parameters included variations in the concentration and particle size of silica. Both particles were first subjected to size determination and settling tests via Stoke’s Law. The silica-hematite system was then suspended in 0.001 M KNO3 electrolyte solutions where pH was adjusted. Afterward, the suspension was agitated and was allowed to settle at different time intervals while obtaining turbidity readings. Results through settling time and turbidity vs. pH graphs indicate that maximum heterocoagulation occurs from pH 2 to 5 while minimum heterocoagulation occurs from pH 6 to 7. At these pH levels the zeta potentials of silica and hematite are negative and positive, respectively. On the contrary, repulsive forces dominate the system from pH 8 to 11 due to the particles’ negative zeta potentials. Furthermore, the attachment of hematite to silica increases when the parameters become larger thereby increasing the effectivity of heterocoagulation at acidic to neutral pH levels.

Jan 1, 2014

By Robert Dunne

A review of the current ?state of the art? of refractory gold treatment will be provided. This will include a global perspective of the refractory processes that are being practiced, where they are and some discussion on why the processes were selected. Some discussion on the challenges that face the refractory gold industry will also be provided.

Sep 1, 2012

By I. N. Babich

"Complex technological problems associated with the processing of mineral raw materials require the search and development of new means and ways of thinking. At present, computer cognitive graphics (CCG) are one of the most actively developing areas of new information technologies. The aim of the study was to optimize the cycle of technological evaluation of ores at all stages of geological exploration of deposits on the basis of analysis of geological sampling data using CCG. A new approach has been developed that facilitates optimization of the whole cycle of subsoil exploration. At the gold ore deposit, the results of the geological sampling data were processed by the method of constructing the CCG in the form of a histogram showing the frequency of gold extraction and the average amount of its content. Significant peaks of the metal content in the ore, exceeding the level of the average content in the ore by tens of times, have been revealed. Graphical interpretation of the parameters of mineralization reflects the uneven nature of its variability, which indicates the presence of large, rarely occurs of gold in the ore and the need to conduct studies on a sample of ore of greater mass than for ores with tiny gold. On a sample of 50 kg gold-quartz ore studies were carried out on gravity enrichment. The maximum size found in the gold concentrate was 0.07 mm. In the course of integrated tests in a gravity concentrate, gold particles up to 3 mm in size were found, which predetermined the need to include the operation of gravity before flotation. A new approach to subsoil research is protected by a patent (RU 2620823).The technological problems that arise before the researcher associated with the processing of resistant ores require the exploration and development of new means and ways of thinking. New problematic situations on complex mineral and raw materials objects are practically not amenable to resolution by existing methods. Integration of industrial and information technologies is necessary. At present, computer graphics (CG) is one of the most rapidly developing areas of new information technologies. For example, in scientific research, including in fundamental research, the accent from the illustrative function of CG (the visualization of what is already known) is increasingly shifting towards the use of computer cognitive graphics (CCG) tools (Bashlykov, 2016). The function of the CCG is to obtain a new knowledge with the help of a graphic representation - a cognitive image or at least to promote the intellectual process of the logical acquisition of this knowledge. In this study, cognitive images are used to graphically represent the distribution of valuable components in the bowels of the deposit, characterizing the state of mineral-raw materials."

Jan 1, 2018

By H. Araneda

Throughout Chile?s history, mining has consistently been a leading industry in the country. The 1990s marked the beginning of a boom in Chile?s mining industry, especially in copper mining, due to both foreign and local direct investment in the sector. Mining?s contribution to the GDP was 15.6% at current prices in 2009, and it accounts for 56% of the country?s exports. Chile?s copper market share reached 35% in 2009. The investment portfolio in mining in Chile for the coming decade has been estimated at 90 billion US dollars. The acute scarcity of human resources currently experienced by the mining sector in Chile will be accentuated in the coming decade as a result of this scenario of investments. The situation is, additionally, similar to the one confronted by other countries involved in the mining industry such as Australia, South Africa, Canada, and in Latin America includes, Peru, Colombia and Brazil. A study carried out by Fundacion Chile, ¨Labor Force in the Chile Mining Industry, Diagnostic and Recommendations, 2011-2020? shows the projected labor shortage for the operation of projects in the development stage, considering only the requirements of the process of extraction, processing, and maintenance. The demand, accumulated incrementally, will be around 115,000 technically skilled workers, professionals, and qualified workers. This figure refers to the operational work force, and does not include the human resources that will be required for the prior stage of the engineering and construction of the projects (brownfield and greenfield). The demand for technically skilled workers and professions for the stages of engineering and construction of the projects that have already received investments is estimated to be 190,000 people for the period 2012-2020. The peak of the demand for engineering is 2012, with a figure that surpasses the 12,000 professionals for all of the engineering specialties. The analysis of the formation of human resources at the tertiary level (where tertiary includes technical/vocational and academic degrees at the undergraduate level) for mining and related majors demonstrates that the programs are scarce with a bias toward theoretical contents and that they are excessively long (40% longer than comparable programs in Australia, Canada, and in OECD countries). The completion rates are low, especially in the technical-vocational programs, which have a completion rate of only around 30%. Finally, the rates of attraction of technically skilled labor and professionals towards careers in mining are insufficient to reduce the identified skill gaps. In the case of university professionals such as geologists, mining engineers and engineers in metallurgy, 80-90% will work in mining. In the case of graduates of relevant majors, that cover skills also utilized by other industries, not only mining?such as maintenance workers, operators of fixed and mobile equipment, etc.?the mining sector appears to be unattractive for reasons such as shift schedules, geographical location of work sites, and other factors. On the basis of the available diagnosis a strategy for the sector has been developed (Workforce Development and Skills Strategy) whose objective is (i) to define a Mining Qualifications Framework to identify the critical roles to be filled (ii) to start, with public resources, a ¨fast-track? training program to assure the availability of at least 28,000 operators (machinery operators, truck drivers, etc.) and maintenance specialists in 2015 (iii) to promote the development of training hubs for mining with learning technologies to train technical labor and professionals on the basis of world class standards (iv) to design and implement a campaign oriented toward the perception of mining as an attractive field of employment opportunity (v) to develop curricular innovations for tertiary education programs, on the basis of international benchmarks. Keynotes: Chile, mining, copper mining, skilled human resources

Sep 1, 2012

By Alan Bax, John D. Lewins

"Platinum Australia Limited (“PLA”) is currently undertaking a Feasibility Study into the development of the Panton Platinum Palladium Project located in the Kimberley region of Western Australia. The Panton Intrusive is a layered, differentiated mafic to ultramafic structurally complex body that has undergone numerous folding and faulting events. This has resulted in a southwesterly plunging synclinal structure some 10 kilometres in length and 3 kilometres wide.High grade PGM mineralisation is hosted within a number of stratiform chromitite reefs within the ultramafic sequence. The focus of the Feasibility Study is on the Top Reef which is situated approximately 150 metres below the mafic/ultramafic interface. The average true width of this reef is approximately 1.2 metres and the reef has a defined resource is 10.1 million tonnes at an average grade of 6.1 g/t PGM + Au.The Palladium to Platinum ratio of the Top Reef is approximately 1.15:1 and the reef also contains an average of 0.4 g/t Au and 0.3 g/t other PGM’s. The Panton ore is considered refractory in nature and standard flotation techniques achieve a PGM + Au recovery of less than 65% with a concentrate grade of less than 100 g/t PGM + Au. As part of the Feasibility Study Platinum Australia in conjunction with their major shareholder Lonmin Plc developed a new metallurgical process which has achieved an overall PGM + Au recovery of approximately 80% into a high grade PGM concentrate which is suitable for feeding direct to a PGM refinery.THE PANTON PROCESSThe Panton Process incorporates a two-stage Milling and Flotation circuit with no cleaning stages to produce a low grade, high recovery flotation concentrate. Typically the concentrate mass constitutes 25% of the feed and has a PGM + Au grade of 25 g/t.This low-grade concentrate is subjected to calcination in a rotary kiln or fluid bed at a temperature of approximately 400 0C for a period of 60 minutes. This step is designed to render the platinum minerals soluble in cyanide and both the temperature and the duration of calcination are critical to the efficiency of the leaching process."

Jan 1, 2003

By C. Stollberg

The recovery of valuable materials from electronic waste is of growing importance for the re-source management not only in the industrialized nations. Being a significant step in an innovative automated process for recycling of metals and plastics from used electric and electronic equipment, the results of the work introduced below, prove the applicability of microbial leaching of metals from printed circuit boards (PCBs) at industrial scale. Within the first project step, which started in March 2005, experiments in shaking flasks with a mixed culture of chemolitotrophic bacteria (mainly Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans) were carried out to study the solubilization of non-ferrous metals present in the electronic waste. It was found that the best results were achieved by means of a two-stage process in which leaching of these metals was carried out by acidified ferric sulphate solutions generated as a result of the prior bacterial oxidation of ferrous ions to the ferric state. Special reactor systems for bacterial generation of such solutions and for the subsequent leaching of non-ferrous metals from the waste were developed, constructed and tested under laboratory and pilot scale conditions. The optimum technological parameters such as concentration of iron ions, pH-value, temperature and presence of nutrients were established for both reactor systems. Parameters such as particle size, pulp density and flow rate of the suspensions being leached were established for the leaching process carried out under continuous-flow conditions. The complex flow sheet reflects a highly efficient technology on the basis of metal recovery, environmental effect and economical acceptance. The process was successfully implemented into an industrial demonstration unit.

Jan 1, 2014

By Yagmur Sirinyurt, Ayhan Ali Sirkeci, Gülay Bulut, Mustafa Özer, Tuncer Acar

"The basic requirement of glass industry for the silica sand is at least 99% SiO2 content. On the other hand, coloring impurities such as Fe and Ti, must be removed. Flotation is the most widely used method for the purification of silica sands from impurities. In this study experimental studies were carried out to reduce Fe content of Mersin (Turkey) district silica sands by flotation. Silica sand sample with a d80 particle size of 1.85 mm was reduced below 0.5 mm in size. Then the size fraction -0.5 +0.106 mm was subjected to flotation tests. In flotation tests, sulfonate-type R801-R825, fatty acid based DER NA 7 (Produced by a Turkish company) and HA110-HA150 a blend of various chemicals produced by Mersin Cam-Is Mining Company (producer of glass raw materials) were used as collectors. Flotation tests showed that sulfonate type R801-R825 collectors provided much better results in acidic medium (pH: 3). The optimum pH value for DER NA, HA150 and HA110 collectors was found to be 7. It was observed that the addition of collector at once caused an increase in the amount of floated product that resulted in a loss of silica to the tailings. In the case of multistage addition of the collector much better selectivity was achieved. As a result of flotation tests conducted under best conditions, a concentrate assaying 0.046% Fe was obtained with a weight percentage of 93.4 when DER NA 7 was used as a collector. In the case of R801-R825 a concentrate was produced with 0.058% Fe content with a yield of 98.4%. On the use of HA150-HA110 the concentrate was produced with 96% weight recovery and 0.052% Fe content."

Jan 1, 2014

By John A. Herbst, Ming Song, Xiangjun Qiu

"It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation (HFS) tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. An illustration of this analysis is shown in Figure 1 below.Here we see that after a new lining is installed (Region I) the wearing process reduces the liner thickness resulting in a larger power draw and an associated higher throughput until Region II is reached. By this point the lifter height is reduced significantly changing charge motion (less cataracting) the power begins to decline, but the comminution efficiency increases with this type of “calmer” breakage environment therefore the throughput continues to increase. In Region III the lifter is no longer providing the minimum required charge lifting action, the power and the throughput both drop off significantly. In the last two stages the behavior is especially complex because throughput is not linearly related to power since grinding efficiency is changing.The study described here shows that these new HFS tools allow the design of wear part profiles which will maximize mill productivity over the entire life of liner/lifter systems. A simple example of such a design procedure is shown involving the selection of a sinusoidal profile for a 34 ft diameter SAG mill.The paper discusses how the principles exposed in this simple example can be applied to search for an optimal profile in which non-standard modifications are allowed to compensate for throughput or wear shortcomings of standard profiles."

Jan 1, 2003