Search Documents

By Chaz Weaver, James Sheahan, Michael Mo

"The Virginia Department of Transportation (VDOT) undertook a program to replace four bridges along approximately 4 mi (6.4 km) of US 340 in Northwest Virginia. Two of these bridges, which span Compton Creek and the Norfolk Southern Railroad respectively, are the subject of this article. HDR provided roadway and structural design as well as geotechnical engineering services for the Norfolk Southern Railroad Bridge while their subconsultant, Saeed Associates, provided structural engineering services in support of the HDR roadway and geotechnical team for the Compton Creek Bridge.The project is located in the Valley and Ridge Geologic Province of Virginia, on an alignment that is adjacent to the Shenandoah River. The project lies within the Beekmantown Group consisting of limestone and dolostone that are prevalent and prone to karstic activity in a band that passes through the project area and north into Central and Eastern Pennsylvania. This area has been impacted by karst limestone conditions where caves and sinkhole activity is common. Caves at Luray and Front Royal, located to the south and north of the project, respectively, are popular public attractions.Since the potential for variability of subsurface conditions can be, and often is, greater in karst terrain, the need to develop a design that provides as much flexibility as possible during construction, and then to be prepared to efficiently review and respond to construction questions is heightened. Coordination and communication among the design staff, VDOT’s design and construction staff, and the contractor was a key factor in completion of this project.Compton Creek BridgeThe alignment for the new Compton Creek Bridge is located about 125 ft (38 m) west of the existing bridge, placing it between that bridge and the existing Norfolk Southern Railroad Bridge. No information about the foundations was available for the existing bridges. Borings in the Compton Creek valley encountered extensive voids (some clay filled and some open) with numerous boulders, rock ledges and pinnacles, particularly on the north side of the creek. Geophysical and geotechnical investigations indicated that below a poor and variable upper zone of rock was a layer of more competent and consistent limestone, which appeared to contain little or no voids."

Jan 1, 2017

By Parameswaran V. S, Anshuman Singh

This is a case study on ground improvement using Stone columns at Kokrajhar in Assam which comes under seismic Zone V as per IS: 1893. The strata at site comprised of mostly fine sands with low SPTN values, fine content less than 10% and ground water table (GWT) at shallow depth. As ground water table subjected to seasonal variation, water table is considered at ground level for designing purpose. The geotechnical profile of the boreholes was analysed on the guidelines of IS 1893 (Part 1) -2016 and it was observed that the liquefaction potential of the soil layers is prominent and ground improvement is inevitable up to a depth of 9.5 m below existing ground level. In order to mitigate the liquefaction of soil layer, Stone columns were proposed. The in-situ soil is densified using wet top feed vibroreplacement method with an area replacement ratio of 16%, so that the relative density of the soil can be enhanced to prevent liquefaction risk. Correlation between relative density, fines content and increment of SPT N –value given by Tokimatsu and Yoshimi (1983) was used for designing purpose. Field tests such as SPTs were carried out at site to validate the extent of SPT (N) improvement. Detail comparison of pre and post density, SPT N values and CRR values were discussed in this paper.

Nov 1, 2022

By Patrick J. Hannigan, Alex Ryberg, Rozbeh B. Moghaddam

Driven piles are widely used for foundation support. In the vast majority of cases, an increase in pile capacity occurs with time which is referred to as “set-up.” However, in a very limited number of cases, a decrease in capacity with time can occur. This phenomenon is referred to as “relaxation.” This paper will provide a brief review of the relaxation phenomenon, as well as pile driving information and dynamic test data on cases where relaxation has occurred. The pile types in the presented relaxation cases include H-piles, open-end and closed-end pipe piles, prestressed concrete piles, and prestressed concrete piles with H-pile stingers. The soil conditions where relaxation occurred includes dense to very dense fine sands, heavily over consolidated clays, and weak laminated rocks. Relaxation information from 36 piles at 26 sites is assessed. The collected data will assist foundation designers by identifying the subsurface conditions where relaxation has occurred, as well as by documenting the corresponding relaxation magnitude. One method of addressing relaxation when it is encountered is to drive the foundation piles to a greater end of initial driving capacity than required long-term. Hence, the identification and quantification of the relaxation magnitude will be beneficial to foundation designers installing similar pile types in similar subsurface conditions. The paper will also present pertinent observations and recommendations on mitigating relaxation when encountered. INTRODUCTION One of the earliest observations of a decrease in redriving resistance following initial driving was reported by Miller (1937). He reported that piles driven into a saturated, coarse grained soil could lose 40 to 50% of their resistance when redriven 24 hours after initial driving. Yang (1956) similarly reported that after a break in driving, a decrease in driving resistance could be encountered for piles driven in dense fine sand, inorganic silt, or stiff fissured clay. Parsons (1966) in his paper that described piling difficulties in the New York City metropolitan area termed this phenomenon “relaxation”. In this time period, pile capacity was most often evaluated from a pile driving formula frequently checked by a static load test. Hence, the true magnitude of the capacity decrease on a given pile was often poorly quantified. Furthermore, dynamic measurements that could determine what influence driving system performance variation had on the observed redriving resistance were not yet readily available.

Jan 1, 2019

By C. Vipulanandan

Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.

By Monique Nykamp

"INTRODUCTIONTerminal 46 is located just south of downtown Seattle, and is one of the Port of Seattle’s busiest container terminals. The Terminal 46 Redevelopment Project was undertaken to replace the existing 15-m-wide (50 ft) cranes along the apron with 30-m-wide (100 ft) cranes, which can unload larger, post- Panamax ships. The project included upgrading the existing waterside crane rail with new piles and constructing a new land-side rail behind the sheetpile bulkhead. The new piles had to be installed adjacent to the existing apron without causing damage, which was a signifi cant geotechnical challenge due to the soft soil conditions at the site. An instrumentation program performed during the test pile program evaluated this challenge and allowed for the development of specifi c production pile installation procedures that had the least possible effect on construction costs and schedule. SITE HISTORYThe site lies along the west side of Elliott Bay, north of the mouth of the Duwamish Waterway. Prior to development, this area was part of the tide fl ats where the Duwamish River drained into Elliott Bay. Prior to 1970, there were several existing timber piers and structures in the area. In the 1970s, the Port of Seattle constructed a 900-m-long (3,000 ft), 30- m-wide (100 ft) apron to support fi ve, 15-m-wide (50 ft) container cranes. The contained backland area was then fi lled with dredged spoils (sand and silt with organics) and the upper 5 to 20 m (16 to 65 ft) backfi lled with sand and gravel.The existing apron was constructed using 0.4 m (16 in) octagonal prestressed concrete piles to support the precast concrete deck and crane rails. The pile-supported bents were spaced at 6.1 m (20 ft), center-to-center, along the longitudinal direction. Pile lengths typically varied from about 20 to 40 m (65 to 130 ft) with 15 to 26 m penetration below mudline (50 to 85 ft penetration). The slope below the apron was constructed at about 1.75 horizontal to 1 vertical to allow for suffi cient water depth for cargo ships. In most areas, a riprap buttress was placed at the toe of the slope. A typical cross section of the apron is shown on Figure 2.Several stability, settlement and pile driving issues arose during the original construction of T-46 (Pita, 1983). Reportedly, movement of the submarine slope occurred during pile driving, resulting in settlement behind the bulkhead. Pile driving reportedly caused settlement of adjacent piles. In addition, some piles were “running” (dropping quickly under one hammer blow) during installation."

Jan 1, 2007

By Monique Nykamp

"INTRODUCTIONTerminal 46 is located just south of downtown Seattle, and is one of the Port of Seattle’s busiest container terminals. The Terminal 46 Redevelopment Project was undertaken to replace the existing 15-m-wide (50 ft) cranes along the apron with 30-m-wide (100 ft) cranes, which can unload larger, post- Panamax ships. The project included upgrading the existing waterside crane rail with new piles and constructing a new land-side rail behind the sheetpile bulkhead. The new piles had to be installed adjacent to the existing apron without causing damage, which was a signifi cant geotechnical challenge due to the soft soil conditions at the site. An instrumentation program performed during the test pile program evaluated this challenge and allowed for the development of specifi c production pile installation procedures that had the least possible effect on construction costs and schedule.SITE HISTORYThe site lies along the west side of Elliott Bay, north of the mouth of the Duwamish Waterway. Prior to development, this area was part of the tide fl ats where the Duwamish River drained into Elliott Bay. Prior to 1970, there were several existing timber piers and structures in the area. In the 1970s, the Port of Seattle constructed a 900-m-long (3,000 ft), 30- m-wide (100 ft) apron to support fi ve, 15-m-wide (50 ft) container cranes. The contained backland area was then fi lled with dredged spoils (sand and silt with organics) and the upper 5 to 20 m (16 to 65 ft) backfi lled with sand and gravel.The existing apron was constructed using 0.4 m (16 in) octagonal prestressed concrete piles to support the precast concrete deck and crane rails. The pile-supported bents were spaced at 6.1 m (20 ft), center-to-center, along the longitudinal direction. Pile lengths typically varied from about 20 to 40 m (65 to 130 ft) with 15 to 26 m penetration below mudline (50 to 85 ft penetration). The slope below the apron was constructed at about 1.75 horizontal to 1 vertical to allow for suffi cient water depth for cargo ships. In most areas, a riprap buttress was placed at the toe of the slope. A typical cross section of the apron is shown on Figure 2.Several stability, settlement and pile driving issues arose during the original construction of T-46 (Pita, 1983). Reportedly, movement of the submarine slope occurred during pile driving, resulting in settlement behind the bulkhead. Pile driving reportedly caused settlement of adjacent piles. In addition, some piles were “running” (dropping quickly under one hammer blow) during installation."

Jan 1, 2007

By Stefan Larsson, Sadek Baker, Razvan Ignat

"This paper describes the execution of two full-scale field tests where a braced steel sheet pile wall interacting with rows of overlapping dry deep mixing columns was first excavated and then loaded to failure. The aim of the tests is to provide insight of the performance of dry deep mixing column rows located in passive zone and interacting with a retaining structure. The column rows were installed perpendicular to the sheet pile walls with two different area ratios, i.e. different distanced between the column rows. Both tests were extensively instrumented with inclinometers, pore pressure transducers, bellow-hoses, earth pressure gauges and strain gauges mounted on the struts. Results of the performedtests will serve as development of design methods for excavation support with columns.INTRODUCTIONDry deep mixing has been used with good results to strengthen the soil when excavations are to be performed in locations with thick soft clay deposits. An application that has increased in recent years is to install columns on the passive side of the retaining structure. Columns can be installed in different patterns but rows, grids or blocks are the most common arrangement. The use of column type ground improvement installed on the passive side of a retaining structure has been documented for a few field cases, Tanaka (1993), O’Rourke et al. (1997b), O’Rourke and McGinn (2006), Ou et al. (2008). By improving the soil on the passive zone, the passive earth pressure in front of the retaining structure is increased. This has proven to reduce the excavation induced deflections behind the retaining structure, reduce the structural forces (bending moment in the retaining structure, strut and anchor forces) and improve the safety against basal heave failure. The main focus of the conducted measurements within these cases has been on recording deflections and structural forces on the retaining structure and there is very little documentation available of the stress-strain behavior of the improved soil acting on the passive side of the retaining structure.Two full-scale tests of braced steel sheet pile walls interacting with rows of overlapping dry deep mixing columns were first excavated and then loaded to failure was conducted during the spring-summer of 2014. This paper briefly describes the test set up, instrumentation, test procedure and some selected results from one of the conducted tests."

Jan 1, 2015

By John S. Civetta, Seth Martin, Marc J. Gallagher, Arthur J. Alzamora, Ronald Peralta

The Crown Building, built circa 1921, is a 26-story iconic building located at West 57th Street and Fifth Avenue in the heart of Manhattan. The paper highlights collaboration between the geotechnical engineer and foundation contractor to develop economical and practical solutions to foundation design and construction challenges associated with this complex redevelopment project. The project includes both below-grade and above-grade expansion of the occupied building, and required undermining the existing foundations, and essentially doubling the foundation loads. The below-grade expansion required surgical foundation work including drilling minicaissons, shoring columns, underpinning, and excavating 20 feet of rock.

By D. Cantali

This paper will be presented in two parts. The first part will present the latest advancements in pile installation techniques using state-of-the-art press-in piling technology by Giken. By pressing in sheet piles and large modulus contiguous steel tube pile walls – as opposed to the more traditional installation methods using percussive hammers or vibrators – retaining structures can be constructed effectively noise and vibration free. For over water and coastal projects with limited access, this provides significant environmental benefits in the form of minimising the construction foot print and the impact to surrounding communities and the marine natural habitat. Typical noise and vibration data will also be presented. The second part of this paper will review the current manufacturing techniques for sheet piles and introduce innovative new materials used in the current piling market for embedded sheet pile walls. Materials include long service life non – ferrous materials such as new age plastics and fibre reinforced polymer piles. Their excellent long term performance and durability make them an effective solution in the marine environment. For steel piles, a number of steel grades with reduced corrosion characteristics will also be discussed including a newly developed steel to combat corrossion in the low water zone, an area often exhibiting the highest moments in a retaining wall. A number of project case studies will also be presented to reinforce their relevance in today’s changing construction landscape.

Nov 1, 2022

By Rudolph P. Frizzi

The current trend of increasing augered cast-in-place (ACIP) pile diameter, length, and load carrying capacities demonstrates improvements in installation equipment, increased acceptance, and that quality control is being successfully implemented by the parties involved in the ACIP pile construction process. Quality control is essential for ACEP piles since 24- to 36-in-dia (610-to 915-mm-dia) piles are currently being constructed to sustain design compressive loads of 800 to 900 kips (3555 to 4000 kN). This paper presents a summary of ACIP pile quality control procedures and methods beginning in the design and bid process, through ACIP pile installation, to post-construction. The results of a recent survey of contractors, engineers, equipment suppliers, and researchers routinely involved with ACIP piles in the United States, Europe, and the Middle East are included to address current trends in ACIP piles and quality control.

Jan 1, 2001

By James R. Gingery, Byron Foster, Bret Lingwall

While microzonation and setbacks are the typical mitigation for structures exposed to surface fault rupture hazards, lifelines and lifeline facilities are not easily relocated to avoid faulting. In these cases, other remedial measures including ground improvement may be warranted. Deep soil mixing ground improvement was used in this case to mitigate surface fault rupture and liquefaction hazards for a pump station at a wastewater treatment plant with wet wells up to 36-feet (11-m) deep. Paleoseismic field investigations were performed to characterize the site, then deterministic and probabilistic fault rupture displacement estimates were made and used to develop design scenarios. The fault rupture mitigation design consisted of a solid block of DSM encompassing and protecting the pump station and its wet wells. Three dimensional soil-structure interaction numerical modeling of the fault rupture scenarios was performed as part of the design. The analyses showed the fault rupture displacements could be diverted by the DSM and that satisfactory structure performance could be achieved. The design required construction of a large 100 percent replacement ratio block of DSM with a compressive strength of 500 psi. Aspects of construction of this DSM block are discussed.

Sep 8, 2021

By Hee-suk Yun, Dae-jin Hwang, Jeong-woo Seok, Myoung-mo Kim

"In this paper, the accuracy of the data measured by a newly developed displacement measuring system, DPRMs (Digital Pile Penetration and Rebound Monitoring system) and its applicability as a quality control tool were verified by field measurements of pile penetration and rebound for pile driving performed at 3 construction sites and 1 test site. The DPRMs data were found to be much better than handwork data. A new dynamic formula for pile capacities is proposed uses the results of a pilot dynamic load test and the final pile penetration. The ratios of pile capacities obtained by the new formula to those by the dynamic load test were 94%±7.4% in the contrast with 123±28.3% by the 5S formula and 68±24.0% by Hiley's formula. This result shows the superiority of the new formula. The ratios of the maximum compressive stresses calculated by using DPRMs to those calculated by using PDA (Pile Driving Analyzer) were about 90-110±10%. This result confirms the applicability of DPRMs as an overdriving monitoring tool. Two sets of DPRMs were used to measure the 3-D displacement behavior of a pile head at the test site. The more the pile head moves laterally, the less the final set values were expected because of the loss of driving energy, but this trend was not obvious within the limited data obtained at the test site.INTRODUCTIONPile construction monitoring consists of two parts. In the first part, enough capacity of the pile is secured to stand the design load. In the other part, pile damage during driving is prevented. Although several methods can be applied to achieve the first part, PDA is nearly the only tool for measuring pile stress.Several methods such as a static load test, a dynamic load test, an Osterberg cell, and numerous driving equations can determine the pile capacity. Among them, the static load test and the dynamic load test are most widely used. The static load test is advantageous because it has the highest reliability. The disadvantages are as follows: it is costly and time-consuming. Also, the capacity of the pile under construction cannot be evaluated. The dynamic load test has lower reliability than the static load test, but it is cheaper than the static load test, is reliable enough to determine the pile capacity, can evaluate the capacity of a pile during construction, and can offer information about construction conditions such as the pile integrity and the pi le stress during driving. The dynamic load test takes a relatively short time and is low cost compared with the static load test. However, it is still costly, time-consuming, and unnecessary to apply to all piles in the field as a construction measurement tool. Therefore, driving resistance (blowcounts) is commonly measured to confirm the pile capacity at construction sites."

Jan 1, 2005

By Lucian Bogdan

On many occasions during construction and service life of the structure, it is crucial to know the load in post tensioning tendons and anchors. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive and the accuracy differs depending on the method used Dyna Force sensor uses the Elasto-magnetic technology (EM) and non destructive testing (NDT) to direct measure stress level in prestressed strands or bars installed on ground anchors or post tensioning tendons. Dyna Force sensor can be used to rapidly read the change in load during proof and performance tests and compare with the pressure gauge and during the life on the anchor to monitor existing lock-off load. It can be used also to determine the load along the bonded length of the anchor allowing the contractor to increase or decrease this length. The paper presents Dyna Force operating principle and some applications. In conclusion, the Elasto magnetic technology applied through Dyna Force is a new and easy to use approach to monitor anchor load during proof test and service life of the structure.

Jan 1, 2009

By Shahid Islam, Lucian Bogdan

"The maintenance of infrastructures has been of particular concern to the engineering community. As the world’s infrastructure expands and existing infrastructure ages, monitoring and evaluation of the structures have become more critical than ever. A large number of retaining walls, tie backs, slope stabilizations and piles are designed using pre-stressing steel. Many piles and drilled shafts are designed using reinforcing steel. There are few testing methods available to assess these tension and compressive forces. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYWIDAG-Systems International (DSI) has been involved in the development, testing and utilization of DYNA Force® sensors to measure the force in the anchors during construction and at any time during the lifetime of the structure. They can be used for bare, epoxy-coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the anchor. The sensor is robust and requires no maintenance. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. This paper describes its application in tie-back and anchor force monitoring of retaining walls and bridge abutment and compression forces in drilled shaft reinforcing steel where the data were collected manually, automated and remotely.INTRODUCTIONOur infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.The elasto-magnetic (EM) technology is a novel approach to monitor forces in steel elements. The DYNA Force sensor is built based on EM technology (See Fig. 1). It is composed of a primary coil and a secondary coil (sensing coil). By passing current through the primary coil, ferromagnetic material is magnetized. The sensing coil picks up induced electromotive force that is proportional to change rate of applied magnetic flux (Faraday's law) and relative permeability. As permeability of core changes, output voltage changes. The output voltage is calibrated to measure the force. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. The sensor has an embedded thermistor which allows for temperature compensation. Due to the diversity of the magnetic property of steel, calibration is done for each type of steel allowing the sensors to perform at their highest accuracy."

Jan 1, 2017

By Sushant Upadhyaya, Deniz Karadeniz, Ahmed Mohamed

Soil setup analysis provides opportunities for efficiencies in pile foundation design and installation. Soil setup gain with time was evaluated as part of the foundation design and installation for twelve bridges along the Interstate 64 corridor between York County and Newport News in Virginia. The substructure elements of the bridges consist of driven precast prestressed concrete piles or H-piles. This case study describes lessons learned to understand the soil setup phenomenon during the installation of the piles in coastal plain. We were able to make expedited decisions during construction by analyzing previously performed pile dynamic analyzer (PDA) test results within the project alignment. Data evaluation included analyses of PDA data obtained from initial driving and restrike after a few hours to 5 weeks. The test data showed pile resistance increase up to twice in most cases and as high as four times in some cases. Foundation design and acceptance based on soil setup can provide opportunities for cost savings and advanced scheduling during construction.

By Federico Pagliacci

"Many existing dams are subject to underwater seepage due to subsoil conditions, like deep alluvial deposits or pervious rocks or karst. Remedial works are necessary in order to install new cut-off walls to stop the water flow. In some cases the cut-off walls have to be executed at depths never reached so far, and difficult to reach with traditional foundation techniques. In many cases the Hydromill technology proved to be the best system to overpass rocky layers and ensure the required verticality. The maximum depth reached by the industry was in the range of 120-150 meters. This article describes the test performed to excavate and cast in place a 3.2x1.5 m panel to a depth of 250 m. The article will also describe the stratigraphy of the site down to 250 meters, as well as the technique adopted to achieve the said depth with deviations from verticality of 30 cm along the longitudinal axis (0.12%) and 20 cm along the transverse axis (0.10%), measured at the bottom of the excavation. The concreting of the panel, for about 1,100 m³, with plastic concrete in the lower portion and conventional concrete in the upper portion will be illustrated. Finally, the tests performed during the excavation and after concrete casting will be also described, with special attention to the continuous directional core drilling that was performed along the whole length of the panel to verify the results of the deviation from verticality, through the onboard instruments, and to control the quality of concrete at a depth never reached before. IntroductionMany existing dams are subject to underwater seepage due to subsoil conditions, like deep alluvial deposits or caves and cavities or acid solutions in the bedrock formations.Conventional remedial works generally consist in the construction of an additional cut-off wall throughout the dam body and the subsoil, in most cases being deeper than the original one. Today, many examples of successful remedial cut-off walls allow the engineers to design the most suitable solution according to the dam and subsoil characteristics and nature.The real difficulty stems from the depth at which the new cut-off wall has to be socketed in competent rock or soil, so as to eliminate underwater seepage. The maximum depth ever achieved with a cut-off wall is 122.5 m for the remedial work of Mud Mountain Dam, Washington, USA, in 1988-1990. This 0.85-1.0 m thick cut-off wall was realized by means of a Hydromill, by excavating single 2.8 m-wide secant panels."

Jan 1, 2017

By Yazn Khasawneh Ph. D. P. E., Will Tjaden, Spencer E. Ness P. E., Mohammed Nasim Ph. D. P. E.

Wind turbine components undergo many loading cycles during their operational life. Additionally, wind turbines may undergo extreme loading conditions from natural hazards, mechanical failures, or emergency stops. Current design practice for the foundations of wind turbines accounts for these complex loading conditions through a simplified pseudo-static approach based structural loading combinations. A rotational stiffness for the foundation is estimated from the pseudo-static analysis and then compared to an acceptable minimum rotational stiffness provided by the turbine manufacturer. These minimum rotational stiffnesses are based on dynamic analysis of the tower and nacelle system with the foundation represented as linear springs. This approach provides a reasonable approach to the foundation design but does not accurately capture the true dynamic performance of the entire soil-foundation-tower-nacelle system. This becomes especially important for pier-type foundations, which are being more commonly used to support modern and future generations of larger turbines. Additionally, the dynamic performance of the foundation will vary as the adjacent soil undergoes a large number of loading cycles of varying strain magnitudes. In this study, the full turbine-tower-foundation-soil system was modeled using finite element methods. An advanced non-linear soil constitutive model and dynamic loading time histories were used to investigate changes in stiffness of the soil, and the possible impact on the dynamic response of the system. Results were compared to conventional design methodologies with the goal of reducing foundation capital costs while avoiding increases in O&M costs and which can lower the LCOE of wind energy.

Oct 1, 2022

By Filippo Maria Leoni, Wesley Schmutzler, Matteo Bertoni

"Deep Mixing Method (DMM) for the Rio Puerto Nuevo Project (Project) in San Juan was chosen by the Corps of Engineers to improve the soils adjacent to a 92 inch ID forced sewer main relocation and to improve the soils for the base of a new drainage channel. The soils to be improved consisted of sandy fill, soft clays, organics and stiff, plastic clays. A pre-construction soil investigation campaign, followed by a Bench Scale Mixing Programme and a Full Scale Field Test were performed during the pre-construction stage to assess soil properties, select binder type and dosage, and disclose the most suitable combination of injection parameters to improve the different soil layers. Production started at the end of August 2012 and was completed in October 2013; over 3,000 DMM elements were installed to a maximum depth of 57 ft below ground for a total gross volume of approximately 125,000 cubic yard. Each element consisted of two 5.5 ft diameter overlapping columns installed simultaneously, and their layout was such to meet the 100% Area Replacement Ratio required by the design. The ground improvement was successfully completed despite some difficulties due to a considerable amount of obstructions. Wet grab sampling and UCS testing of the retrieved specimens were designed as the main QC/QA method for the verification of the quality of the ground improvement. Upon completion of production, approximately 3,000 specimens were cast. The contract also required continuous coring of at least 12 randomly selected DMM elements and the testing of 8 cored specimens per bore for strength assessment. This paper will illustrate means and methods used in the field to construct the designed ground improvement and the results of the QC/QA program, with a focus on the differences between wet grab and coring sampling methods.INTRODUCTIONThe Rio Puerto Nuevo project involved the stabilization of a major drainage channel using the Deep Mixing Method (DMM), and the relocation of a 92 inch ID forced main sanitary sewer outfall. Previously, in 2004, a 40 x 16 x 2,000 ft. box culvert was installed under a different contract to convey runoff waters to the ocean.However, the connection between this culvert and the upstream network of channels was not constructed due to the presence of the forced main sewer pipe. In order for the drainage system to be completed and function properly, the 92 inch ID forced main needed to be lowered about 20 ft to allow for proper drainage.DMM was chosen by the US Army Corps of Engineers to stabilize the drainage channel as well as improve the soil under the relocated sewer main. The DMM was arranged in different zones (A through E) with variable top and bottom design elevations as can be seen in the typical cross section for Zone A (deeper and with a higher strength requirement) and Zone B as an example (Figure 1)."

Jan 1, 2015

By James S. Graham

Research at the University of Colorado on southern pine and Douglas-fir piling has determined that the existing building code design stress values of 1200 psi and 1250 psi, as determined by ASTM D-2899, are substantiated; but testing procedures should be revised. All full size piling tests should be standardized at 1/d ratios of 2:1, or confined tests performed. Also, it has been determined that theoretical design values for timber piling should not be based on the lumber criteria of D-245 and D-2555, but instead should follow the pattern set by engineers in the utility industry for timber poles, in accordance with ANSI 05.1.

Jan 1, 1986

By Jim Rix, Ken Been, Nihal Bohra, Anthony Rice, Juan Lopez

"A temporary bridge, supported on steel pipe piles, was built to expedite the construction of a breakwater structure off the western coast of Peru. The bridge provided access for dump trucks to the breakwater across a 342 m (1122 ft.) wide navigation channel from a liquefied natural gas (LNG) loading facility, at the end of a 1.3 km (0.82 miles) long permanent trestle, in 15 m (50 ft.) water depth. After the completion of the breakwater, the temporary bridge was removed, and the piles were extracted approximately one year after the initial driving. The bridge deck was typically supported on pairs of 914.4 mm (3 ft.) diameter, 18 mm (0.708 inch) wall steel pipe piles spaced at 7.5 m (24.6 ft.) across the bridge width and 18 m (60 ft.) along the bridge length. In an attempt to reduce the driven pile embedment, an inner closure plate was installed at 2.7 to 7 m (9 to 23 ft.) from the pile toe to force closed-end behavior. The piles were designed to carry 3400 kN (383 tons) axial compression load, and a minimum of 8 m (26 ft.) embedment was specified to provide sufficient resistance to the lateral loads.The subsurface conditions consisted of cemented conglomerate of sand, gravel, pebbles and some boulders, locally known as the Cañete Formation. The driven pile embedment varied widely, between 8 to 24 m (26 to 79 ft.). A significant portion of each pile was above the seabed, passing through seawater and up to the bridge deck, and was therefore unsupported. The extraction of the piles was challenging due to the subsurface conditions, presence of significant water column, pile weight, and the inner closure plate. Several different approaches were attempted before the piles could be successfully extracted. This paper summarizes the difficulties encountered and observations made during the driving and extraction of these piles."

Jan 1, 2017