Search Documents

By J. M. Mitchell

Kuala Lumpur, Malaysia is underlain by karstic limestone. Firm clays, mudstones and siltstoncs of the Kenny Hill Formation overlie the limestone for about two thirds of the city. The remaining third has deep deposits of very soft alluvium, or tin mining slimes, overlying the limestone. It is only recently that large buildings have been constructed in the area. Arup Jururunding have been concerned with several projects located on the limestone, although space here only permits the description of four sites in detail. The experience has allowed the development of a design approach for the foundations. The aim is to make the architectural scheme compatible with the geology. This is not always possible, and examples are given of both situations. The case histories give examples of compensated foundations, and piled foundations include steel H-piles, precast concrete piles, micropiles, bored piles with rock sockets, and barrettes up to 90m deep.

Jan 1, 2010

By James A. Mason

The State of California has instrumented numerous buildings, bridges, and dams throughout the state with earthquake recording devices. These accelerometers are strategically placed to measure the response of the structure to a specific seismic event. This comprehensive program enlightens the field of seismic engineering after each earthquake. The Office of Strong Motion Studies, California Strong Motion Instrumentation Program, a sub-branch of the Division of Mines and Geology, provides a professional service unequalled in the world. Within hours of a local earthquake, a preliminary report with the epicenter / hypocenter, structural damage, and time history records are available to all interested parties. The included partial report in the appendix, see section 5.1, is one of the reports that C.S.M.I.P. produced after the Loma Prieta Earthquake of October 17,1989. The diagram on the cover is even of interest. This is a small portion of San Francisco. The values on the diagram are the recorded maximum horizontal ground accelerations at that location in the city. For example, the acceleration at Yerba Buena Island was 0.06g. (The "g" refers to the acceleration of gravity. Thus, a 0.06g acceleration refers to the force, F=m*a, that the structure would experience. For this case, the force would be six percent, 6 % , of the mass of the structure.) Yet, directly on the other side of the Bay Bridge, at Treasure Island, the acceleration was 0.16g. Yerba Buena Island is a natural island composed of hard granular material. Whereas, Treasure Island is a man-made island of imported filled. Here one can see the absorption / transmission difference between hard material, which interact with short seismic wavelengths, and soft cohesive material, which interact with long seismic wavelengths.

Jan 1, 1993

By Fritz J. Klingler

From site demolition, to design, to construction, Detroit's new Tiger Stadium project is required to be completed within a short 2 ½ years from award of the design-build contract. Such extreme schedule requirements together with somewhat difficult ground conditions at the site, resulted in several challenges in the design and construction of the deep foundation system for the stadium. During the geotechnical investigation, an intermittent water bearing sand layer was encountered overlying the hardpan at the site. As a result, some concern developed regarding the potential for collapse of caisson bells within this layer, as well as the potential for flooding of the caissons during drilling. Although sand and/or ground water was encountered within about half of the caissons, standard drilling and belling methods were used, and adverse conditions were controlled in almost all cases through expeditious drilling, inspection and concreting of the caissons. This paper will present a summary of the ground conditions, design and specification requirements, and construction methods used to successfully install the caissons for this project.

Jan 1, 1999

By Jacques Moraille

The public is asking for more aesthetic designs if they can be proven cost-effective at providing an appealing element to new dams. Lake Lenexa was designed and built around the idea of providing for basic dam functions such as flood control, enhanced water quality, recreation but also to provide an inviting community focal point for the residents to visit and enjoy; truly interact with the dam. The architecturally unique dam and ?one of a kind? spillway were designed to symbolize the water cycle as water moves from nature into the urban environment and the back to nature. A pedestrian bridge that spans the spillway offers visitors a good view of cascading pools and a fountain. The original Lake Lenexa dam layout incorporated relatively high, cast-in-place concrete retaining walls to form the spillway structure. The Black & Veatch project team performed a Value Engineering (VE) study to determine cost-effective means for implementing architectural features within the spillway, which resulted in innovative uses of construction materials not typically used in dam and reservoir construction. The VE study concluded that mechanically stabilized earth (MSE) retaining walls that are normally used for transportation projects would be a cost-effective alternative to the originally planned cast-in-place wall systems for the main spillway and stilling basins. The Black & Veatch study added value by mixing cement-kiln dust (CKD) with on-site clay soils to produce a stabilized material for use under the spillway. The CKD stabilized material properties include low compressibility, high strength and low permeability, which reduced seepage and uplift pressures under the spillway slabs. The cost savings provided by the VE alternatives reduced total costs and enabled architectural elements. The award winning dam design also used drilled caissons, expanded polystyrene (EPS) block forms, customized steel forms and external concrete vibrators to build the pedestrian bridge and upper spillway structures.

Jan 1, 2009

By James A. Schneider

The successful installation of long piles driven into very dense sands relies on the occurrence of the reduction in local friction with increased pile embedment, a phenomenon known as ?friction fatigue?. The underlying mechanisms controlling friction fatigue are poorly understood, with some design methods including an adjustment for the influence of pile diameter while others do not. This paper back calculates the installation resistance of 0.356m to 2m (14in to 78in) diameter open ended piles driven into very dense sands using wave equation analyses. Cone penetration test data are used to link soil properties to installation resistance. The study illustrates consistent interpretation of a variety of case histories of open ended piles driven in very dense sands using newly developed analysis techniques and normalized parameters. Results provide information on methods for incorporating friction fatigue into drivability studies as well as a discussion of mechanisms related to pipe pile installation resistance in sandy soils.

Jan 1, 2010

By Naresh Koirala

The Greater Vancouver Regional District completed installation of a 2.5 Km long, 2400 mm diameter concrete sewer in Delta, British Columbia in 2000. The sewer traverses through area of peat and soft ground. The ground investigation along the sewer alignment consisted of cone penetration tests and auger drilling with standard penetration tests. The gravity sewer is supported on precast, pretensioned spun concrete piles imported from Malaysia which had never been used for a major project in North America. The capacities of the installed piles were tested using pile driving analyzer (PDA) and three static load tests. A total of 46 PDA tests were carried out during pile installation. The paper describes the pile vetting process the owner went through prior to accepting the piles for use in the project and performance of the piles. It compares the pile capacity estimated from the PDA tests with that estimated from soil mechanics methods using data from cone penetration tests and standard penetration tests. The ranges of estimated capacities calculated by different methods are discussed from design capacity selection considerations.

Jan 1, 2004

By Joel Moskowitz

A new office complex is being constructed within 25m of the Hudson River in New Jersey. The project, about 140 m by 100 m, will include 4 basements under the entire footprint. The perimeter was to be secured by a 0.8 m thick diaphragm wall, laterally supported by high capacity tieback anchors to rock. Columns were to be supported on footings or piers to rock at a nominal bearing pressure of 3.8 MPa at depths up to 17m. Although some variation in rock quality was observed in borings, a substantial vertical seam of weathered and/or decomposed rock, 1 to 2 meters wide by as much as 8 meters deep, was encountered during construction necessitating field redesign. In some locations the seam dipped below more competent rock. Footings were redesigned for support on drilled caissons, or soft rock was excavated and replaced with concrete necessitating a reduction in bearing pressure of the footings by one half.

Jan 1, 2002

By Walter G. Kutschke

Four significant soil nail wall projects in the eastern United States were recently completed with a combined area of 175,000 square feet of finished shotcrete surface. These projects required the use of innovative design and construction methods in order to address various challenges, including slide-prone back slope materials, perched water, highly erodible rock materials, curved wall alignments, very tight construction tolerances and unexpected subsurface conditions. Special focus is given to issues such as bench excavation, soil nail installation methods, shotcrete mix design, anticipated shotcrete quantities, shotcrete nozzlemen qualifications and weather conditions, in order to provide a lessons-learned database for future soil nail wall design and inspector considerations. These projects also underscore the importance of design engineer and soil nail wall contractor qualifications as well as effective communication with the owner.

Jan 1, 2007

By Özgür Bezgin

This paper presents observations on the installation of drilled shafts from two construction projects and an academic study with experimental and analytical parts. The construction projects involved the use of pressurized drilling methods. The experimental part of the academic study involved the use of the auger drilling method. The analytical part of the academic study investigated the effect of drilling methods on the soil-structure interaction and the behavior of drilled shafts under lateral loads. The concept of ?free-length? is introduced for the lateral load design of pressure-drilled shafts that are thought to be fully embedded within a soil media. The academic part of the study presented herein was conducted in Rutgers, the State University of New Jersey.

Jan 1, 2009

By Yukihiro Ishihara, Nanase Ogawa, Ming Lei

"Abstract In the Press-in Method, a static jacking force is used to install a prefabricated pile, while a reaction force is gained from previously installed piles. This piling technique has solved problems in urban piling construction such as noise and vibration associated with the piling work, restricted construction conditions due to the existing structures, and so on, since its emergence in 1975. Its applicability to hard ground conditions has been improved, with the development of press-in machines that involve augering or rotation. Besides, information such as time, penetration depth, jacking force and rotational (or augering) torque in piling work are automatically obtained. The concept of PPT, Pile Penetration Test, has been developed by the authors, to apply the obtained information to the processes of construction planning or foundation design. This paper highlights the technique to estimate SPT N value from data acquired in standard press-in (press-in without any auxiliary methods), press-in with augering and rotary press-in. The technique will be helpful in assuring the adequate embedment depth, re-selecting the adequate press-in machine or auxiliary method, and re-pricing the project objectively, particularly when a contractor encounters unexpected ground conditions.INTRODUCTIONThe Press-in Method is one of the piling techniques that use a static jacking load to install piles. It mitigates environmental problems of noise and vibration that have been associated with other conventional piling techniques.It is also featured by its spatial efficiency; since a ‘press-in’ piling machine gains a reaction force from the previously installed piles, there is no need of bulky weights that will occupy a large space. This feature is emphasized in the piling system in Figure 1, where a press-in machine and its related devices are all positioned and ‘walk’ on top of the pile wall.Its applicability to hard grounds has significantly been improved, with some newly developed piling machines that involve augering or that install tubular piles with teeth on the base by applying axial load and rotational torque at the same time."

Jan 1, 2014

By Morgan L. Race, Matthew R. Glisson

"Most driven pile projects have plumbness limits from 0.25 in/ft (21 mm/m) to 0.5 in/ft (42 mm/m) to control bending stresses. For two projects, the project teams performed static load testing to evaluate performance of piles with sweep. One project, located in Grand Forks, North Dakota, used 9.625-inch (244-mm) diameter piles with a wall thickness of 0.395 inch (10 mm) and lengths ranging from about 130 to 160 feet (40 to 49 m). Measured pile sweep (lateral offset distance of the pile toe from the pile top) was between 12 and 17 inches (305 to 432 mm). Static load testing indicated that the piles could support the design load with axial deflection of less than 1 inch (25 mm) but only provided about 80 to 90 percent of the ultimate resistance at axial deflections of about 1.9 to 1.7 inches (49 to 43 mm), respectively. The other project, located in Shakopee, Minnesota, used 9.625-inch (244-mm) diameter pile but with a wall thickness of 0.352 inch (9 mm) and lengths around 50 to 90 feet (15 to 27 m). The measured sweep varied between about 20 and 63 inches (508 and 1,600 mm) for 9 of 214 piles driven at the site. Load testing indicated that these piles could provide the required design resistance with less than 0.3 inch (8 mm) of axial deflection and support the required ultimate resistance with about 0.5 to 0.6 inch (13 to 15 mm) to of axial deflection.INTRODUCTIONAnyone who has observed a significant number of piles has seen that, inevitably, the pile is not perfectly straight after driving. In spite of the best efforts of contractors, there are a whole host of reasons for piles to end up out-of-plumb or to have a curve, sometimes referred to as pile sweep. Most project specifications set limits for plumbness typically between 0.25 in/ft (21mm/m) and 0.5 in/ft (42mm/m) (USACE, 1991; PDCA, 2007; MnDOT, 2016; MoDOT, 2016). Closed-end pipe piles, including monotube or tapertube, are the only pile type that allow actual measurement of the final alignment of the pile.As Nadeem, et al. (2015) note, buckling failure of long, slender piles is the predominant mode of pile failure in soft soils. Pile sweep is just one source of buckling failure in long, slender piles. The nonlinear buckling analysis showed that increasing slenderness ratio and/or increasing degree of curvature decreases the loadcarrying capacity of a driven pile. Nadeem, et al. (2015) considered solid, steel pile with lengths from 24 to 66 feet (7.5 to 20 m), diameters from 9.75 to 26 inches (244 to 660 mm), initial bends from 2 to 6 inches (50 to 150 mm), and half- and quarter-sine shapes."

Jan 1, 2017

By Takefumi Takuma, Masashi Nagano, Christopher DellAringa

Multiple agencies in Southern California are retrofitting and upgrading their levees to catch up with ever-advancing urbanization affecting the requirements for existing channels and levees in this seismically active zone. Pressed-in sheet piles have been specified on some of these projects to minimize noise and vibration problems associated with sheet pile installation. This paper will study three Southern California levee and sewer pipeline retrofit projects that utilized pressed-in sheet piles in hard soil conditions with N-values higher than 50. BACKGROUND Southern California is home to numerous drainage channels fortified with earthen levees. In spite of the region’s semi-arid climate with varying annual precipitation from year to year, winter storms can bring in heavy and continuous rainfall to the area which overwhelms the levees’ capacities at times. Some levees are running through densely populated areas with homes and other sensitive structures such as underground utilities and bridge piers. Conventional sheet pile driving utilizes either percussive or vibratory pile driving methods, both of which generate high levels of noise and vibration, causing nuisance and potential damage to nearby structures. On the other hand, the press-in piling method utilizes a hydraulic force to push piles into the ground, thus practically eliminating the noise and vibration issue. Although there are types of press-in piling systems mounted on tall leaders on large crawler-base machines, they are less frequently used due to its much larger size and more limited drivability than the type discussed hereunder. The other type of press-in machine sits on top of already installed piles and is anchored with its own weight and additional counter weight when starting off as shown in Figure 1. Once the first few piles are pressed in, the equipment grips on top of the installed piles and moves forward on its own as the pile installation progresses. See Figure 2. This method does not use a vibratory or percussive force to install piles.

Jan 1, 2018

By Marc Dondelinger

Interlocking H sections with deep webs and high section modulus are being used for cofferdams and shore enclosures where pressures are excessive. The H sections can be as much as a meter deep; they can be used as continuous interlocked wall. A steel saving alternate is spacing the H and driving deep for stability then filling between with shorter interlocking sheet piles. Templates provide for exact positioning.

Jan 1, 1985

By Roy M. Schnabel

The Fashion Island Boulevard Bridge over the Marina Lagoon in San Mateo, California is an eight span precast, prestressed concrete girder bridge. It is approximately 495 feet in length and 61 feet in width. It is supported on 36" diameter octagonal, hollow precast-prestressed concrete pile columns. The bridge was constructed in 1968 and suffered considerable damage during the Loma Prieta Earthquake in 1989. A damage survey report prepared by the State's Office of Emergency Services (OES) recorded that sixteen of the twenty-one pile-columns sustained heavy to moderate damage from the Loma Prieta Earthquake. The damage consisted of cracking and spalling at the tops of the pile-columns. Spalls at the most heavily damaged columns exposed the prestressing strands and confinement reinforcing which also showed signs of corrosion.

Jan 1, 1993

By John R. Wolosick

MACROPILES are defined as ultra-high-capacity micropiles, with working loads in excess of 250 tons. The piles are typically 9-5/8 to 24 inch (244 to 610 mm) outside diameter. They are drilled and grouted in place, with either large diameter steel bars and/or steel pipe reinforcement. The piles are typically tested to twice the working load. Piles with working capacities of up to 500 tons and tested to 1000 tons have been installed. The paper discusses MACROPILE design philosophy, construction techniques, and two case histories where this innovative foundation system has been installed. Macropiles are descended from micropile technology pioneered in the early 1950s by Fernando Lizzi of Italy.

Jan 1, 2006

By Darrell Wilder

When designing excavation support systems in urban environments, it is often necessary to consider the effect of vertical surcharge loads from adjacent structures. Several methods are used in practice to establish the horizontal surcharge-induce pressure on the excavation support. According to the experience of the authors, these methods often seem to overestimate the effect of the surcharge and may have significant impact on the construction costs. This paper explores several of these procedures and provides a discussion as to the reasons for the differences in surcharge effect predictions between different procedures. It also provides practical recommendations for designers dealing with excavation support design.

Jan 1, 2006

By Mohammed Sakr

A Two-Section Helical Pile (TSHP) is a steel pipe with two shaft sections of different diameters and with one or more helix plates near the bottom of each shaft section. TSHPs are used regularly in western Canada as foundation pockets for single and double circuit distribution power line poles. The results of a comprehensive lateral pile load test program and the field monitoring of TSHPs installed in organic soil (muskeg) over soft clay are presented in this paper. A total of nine full scale lateral load tests were carried out, including seven tests using TSHPs with different diameters and embedment depths, and two tests using one-section helical piles. The prime objective of the study was to evaluate the lateral resistance of TSHPs installed into very soft organic soil (muskeg) overlying soft clay soils, to compare their lateral resistance relative to one-section helical piles and to compare the measured and the estimated lateral resistances using p-y curves. In order to provide sufficient soil data for analysis, the subsurface soil stratification was evaluated using two different techniques including; Cone Penetration Tests (CPT) and Portable Soil Probe Tests (PSPT). The two testing techniques were also compared and evaluated. This paper summarizes subsurface soil conditions, pile configuration, helical pile installation procedure, testing setup and results.

Jan 1, 2009

By Ian Vaz, Takefumi Takuma

"The New Orleans area has been repeatedly flooded by major storms and hurricanes since its French colonial era. After severe flooding in May 1995, the U.S. Congress authorized a massive flood protection project called the Southeast Louisiana Urban Flood Control Program (SELA) in 1996 to improve interior drainage in Orleans, Jefferson, and St. Tammany parishes. However, the project was not fully funded before the landing of Hurricane Katrina in 2005 and Hurricane Rita, which breached many of the area’s levees and flooded 80 percent of the city. Finally, the project was fully funded in 2008 and has been worked on towards its 2017 completion. Another large project simultaneously worked on in the area is the Hurricane and Storm Damage Risk Reduction System (HSDRRS). This system was designed for a 100-year level of flood risk reduction. One particular project within the HSDRRS rendered successful due to an unconventional method of pile driving that was utilized to install sheet piles to reinforce an existing concrete I-wall. This paper will discuss how and why this non-vibratory method of sheet pile installation allowed the project to be successfully completed ahead of schedule.INTRODUCTIONSteel sheet piles were utilized on many of the SELA and HSDRRS projects for permanent cutoff walls under concrete I-walls or T-walls or for temporary earth retaining walls of drainage structures. Although the SELA Project was established in 1996 after severe flooding the year before, hardly any work was done on it until the two catastrophic storms Hurricanes known as Katrina and Rita triggered its revival. These two hurricanes also triggered the HSDRRS soon after the storms’ devastation. The SELA project authorized to improve interior drainage systems while the HSDRRS project was authorized to raise or restore levees and floodwalls mainly along Lake Pontchartrain, the Mississippi River, and Lake Borgne in addition to other areas. Figure 1 shows the SELA Projects that have been completed, are still under construction, or approved for construction. The projects fully highlighted in yellow within the map specified the press-in piling method. These improvements included drainage systems, pump stations, surge walls, and outfall canals as enhanced protection for future storms similar to Hurricane Katrina that caused so much damage by inundating the New Orleans area in August and September 2005 respectively (Facts and Figures, 2012). The completion of these projects were the responsibility of the U.S. Army Corps of Engineers, New Orleans District.Due to the fact that many of the projects were in densely populated areas, the Army Corps of Engineers specified a non-impact, non-vibratory press-in piling method for driving and extracting sheet piles for many of the projects to mitigate noise and vibration impacts. The soft soil conditions in the New Orleans area was also a contributing factor in the Army Corps of Engineers’ decision to specify this piling method due to the risk of settlement for existing historical as well as modern structures. In addition, there were other projects that elected to use the press-in method without any contractual requirements. One of these projects was the Inner Harbor Navigational Canal Reach II Emergency Interim Repair which was part of the HSDRRS project that has been under construction since its authorization in 2005 (Facts and Figures, 2012)."

Jan 1, 2017

By D. Michael Holloway

The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the structures along the realignment of Interstate 880. The project replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers well beyond local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata and quantifying the effects of installation on the long-term capacities of the piles led Caltrans to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1995

By Arpit Parikh

"Ground Water or Pore water pressure development in Sandy Soil formation is Critical situation in foundation analysis and design.Moreover it become severe while associated with higher liquefaction probability in river bank areas. It is difficult to find cost optimized solution for liquefaction mitigation under limited budget allocated for the project. Here in these research paper the attempt has been made to have clear picture of liquefaction by using various techniques and field tests. And its mitigation by suitable foundation type. In Bangladesh, On Bank of River Meghana, Power plant structures are proposed. The particular site is full of fine sand having partial silt throughout from EGL to 55 m depth. Hence in addition to Conventional Boring / Drilling operations, CPLT, SCPT, SCHT and PMT had been performed to arrive deterministic effect of liquefaction. By use of Geologismiki software and some excel based programs developed which indicates that Certainly liquefaction occurs under the event of earthquake. By Checking past records of Bangladesh we found, there are small magnitude earthquakes are inevitable and frequent. Hence fourth to overcome the bad effect of liquefaction, the deep pile foundation -Driven Pre Cast Solid Square Pile of 400 mm dia. had been suggested for various types of power plant structures. Which densify the soil and ground will improve in resisting liquefaction.1. INTRODUCTIONA Detailed Geotechnical/Foundation design Analysis had been done to arrive at optimum foundation design solution in highly probable liquefaction zone of Silty Fine Sand near Dhaka City of Bangladesh for proposed 750 MW Cyclic Power Plant. Hence about 24 no. of (Borehole) Boring and Drilling up to depth of 55 m from existing ground level has been carried out. Additionally, 09 nos. of Static Cone Penetration Test (SCPT), 02 Nos. of Dynamic Cone Penetration Test (DCPT), 02 Nos. of Pressure meter test (PMT), 02 nos. of Cyclic Plate load test (CPLT) of suitable capacity with 06 nos. of Seismic Cross Hole Test (SCHT) in boreholes had been carried out. The purpose of PMT and SCHT was to have clear idea about the Seismic behavior - knowhow of site. According to Basic principles of Soil Mechanics and foundation design, it is proved that PMT & SCHT are dynamic test. These tests stimulate field condition of occurrences of earthquake. In later stages of analysis, it is found that site have high probability of liquefaction through use of Geologismiki – Liquefaction Analysis Software. Author of these research paper also felt earthquake vibrations – strong aftershocks during site study where Epicenter of the earthquake was in Myanmar during month of august 2016."

Jan 1, 2017