Search Documents

By Yong Jingrong

Based on the results of several test socketed piles in Sichuan, the mechanism of the deformation for a loaded socketed piles is investigated, and the concept of the socketed effect is proposed. The bearing capacity and settlement of socketed pile are controlled directly by socketed effect, that is an important mark different from the other types of cast-in-situ piles. According to the analysis of this effect and factors interferring it, their roles are discussed with the results of test piles. In order to increase the bearing capacity of piles, the ways and methods enhancing socketed effect are recommended.

Jan 1, 1991

By Kam Ng

For bridges or buildings that may be subjected to large vertical and lateral loads, drilled shafts offer an economic foundation solution. While the current drilled shaft design practice is considered adequate, introducing a performance-based approach to designing the drilled shafts will make their design more cost-effective and produce more dependable response. This concept was examined using analysis of 41 drilled shaft load test data from several states. This process identified the challenge with the lack of information from the Osterberg (O-cell) load test method to characterize the full top load-displacement response. When a typical single O-cell is utilized in a drilled shaft test, depending on the location of the O-cell and the geomaterials present along and beneath the shaft, the load test result typically quantifies either the side resistance or end bearing reaching the ultimate load-displacement curve but not both components. This limitation hinders the determination of a suitable shaft resistance as a function of a target top displacement. To overcome this challenge, an improved procedure is proposed for establishing the full load-displacement curve based on data gathered from one O-cell. The method will be presented in the paper for three different cases (i.e., side resistance reaches the ultimate during the test, end bearing reaches the ultimate during the test, and neither components reach the ultimate values). Because it allows the characterization of the full load-displacement curve, the proposed procedure will allow performance-based design of drilled shafts with due consideration to settlement while satisfying the Load and Resistance Factor Design.

Jan 1, 2013

By John A. Egan, Nathaniel Wagner, Micaela Largent, Jonathan P. Stewart, Debra Murphy, Jeremy Butkovich

The Millennium Tower is a 58-story reinforced concrete building that was constructed in San Francisco, California between 2005 and 2009. The Tower is founded on an embedded pile supported mat with pile tips bearing in dense marine deposits that overlie an over-consolidated marine clay layer known locally as Old Bay Clay. This clay layer experienced stress increases from Tower self-weight and from multiple episodes of de-watering between 2006 and 2018 at the Tower site and neighboring sites. Settlements of the Tower foundation have been measured since 2006 and lateral deflections of the Tower have been inferred and measured since 2009. Available information on this case history include geotechnical site conditions and data from a monitoring program that tracked foundation settlements, Tower tilt, groundwater levels at the Tower site, and ground inclinations over time. This presentation will discuss the ground deformation mechanisms that caused the observed movements, the degree to which the movements can be predicted, and lessons from this case history for the design of deep foundations for tall buildings in San Francisco and geologically similar regions.

Sep 8, 2021

By Michal Topolnicki

Deep Mixing Series: This article is the second keynote highlighted from DFI's virtual Deep Mixing Conference in 2021, for which Topolnicki served as a committeee co-chair Polish applications of deep soil mixing (DSM) technology occupy a leading position in Europe. That includes use for road and railway embankments, bridges, residential and industrial build- ings, silos, commercial centers, slabs, car parks and storage yards, excavation supports and cut-off walls. In fact, more than 350 road and railway viaducts and 200 wind turbines have been founded nationally on DSM columns, which are firsts on an international scale. This represents more than 1,200 imple- mentations by the Polish geotechnical industry. Considering the need to update DSM design recommendations, this article will attempt to summarize the best practices of wet DSM design and implementation, in particular. It draws on 20 years of experience and will high- light the properties and principles of the design of stabilized soil and lessons learned. Case studies are included to fur- ther understanding of the careful con- siderations needed with this technology.

Apr 1, 2022

By Georgette Hlepas

How often phrases like these have been made by project managers and project teams trying to explain why there has been cost growth, project delays and differing site conditions claims. But does it really take x-ray vision? Do we really approach geotechnical construction projects unprepared for the subsurface that may be encountered because we can't get the answer? Too often our industry seems to think the answer is, "yes." However, this is not because we can't understand the subsurface. All too frequently it is because a choice is made to save money or time by foregoing or shortchanging upfront subsurface investigations. This is accepting a risk at the beginning of the process and realizing it during construction. Case histories have proven time and time again that upfront investment in site exploration and constructing a ground model mitigates risk in design and construction. But how much do we prepare? What level of investigation (or investment) is appropriate? The answer of course, is it depends; how much risk are you willing to take for your project and what are the potential consequences?

May 1, 2022

By RAP Bement

Installation by vibrodrivers of sheet and bearing piles generates periodic vibrations in the surrounding ground, which have been widely measured and reported. One of the possible consequential effects of these vibrations is ground settlement caused by the compaction of loose granular soils. Vibratory compaction settlement of a range of granular soils has been studied in the laboratory using a 150mm diameter Rowe cell, which allows sample preparation and control during vibrations equivalent to conditions in the field during vibrodriving. The cell containing the soil sample was mounted on an electromagnetic shaker and vibrated at amplitudes and frequencies appropriate for soils adjacent to vibrodrivers. The changes in sample height were recorded.

Jan 1, 1996

By V. T. Ganpule

The effect of Sulphate and Chloride is well understood by the engineers. Most of the codes stipulate permissible limits for sulphate and chloride content in groundwater. Relatively few reference are available about the effect of organic acids on pile concrete. While executing a pile foundation work around Bombay, the authors came across the peculiar phenomenon. The routine testing of water has indicated that water is non-aggressive; however, on exposing the piles, the piles were found to be highly detonated. The testing of water on the guidelines followed by engineers associated with flow through pipes revealed that water is corrosive as per the Ryznar index concept. The present papers discussess the significance of Ryznar index in under water concreting.

Jan 1, 1996

By Carl Ealy

Static and STATNAMIC (STN) rapid load test (RLT) was performed on 3-drilled shafts. The purpose of the RLT part of the study was to obtain data in support of FHWA research on innovative load testing methods. The research site is located at the National Experimentation Research Site (NGES) in Amherst Massachusetts and is underlain by Connecticut valley varved clay. Two of the tested shafts were constructed without planned defects and the third with manufactured defects to evaluate current non-destructive integrity testing (NDE) methods. Quick Load Test (QLT) and Constant Rate of Penetration (CRP) static axial load tests were performed on two shafts to plunging failure. Good agreement between static and RLT derived static failure loads was attained for a 5% failure criterion (load at a movement equal to 5% of shaft diameter).

Jan 1, 2002

By Andrew Pontecorvo, Steven Lowe, David Sposito

Buildings with large height-to-width ratios require foundations with significant uplift resistance. This paper presents a case study of the permanent rock tiedowns installed for One Manhattan West, a sixty-seven-story office building in midtown Manhattan. Site access and schedule dictated the size of the equipment for installing the tiedowns would be limited to drilling a 16 inch (406 mm) diameter hole. A three bar configuration of 3 inch (76 mm) diameter high strength threaded bars was chosen to develop an allowable capacity of 923 tons (4060 kN) per tiedown. Although the quality of the rock at the site was generally high, a challenging geologic condition emerged during the installation of one of the tiedowns requiring a creative installation procedure. Although the three bar configuration performed relatively well there are challenges with loading and testing this bar arrangement. Unlike single bar tiedowns that are typically tested with a high success rate, testing of a multiple bar system can result in some unsatisfactory results. This may be attributed to the installation challenges, difficulty loading each bar uniformly and/or the method of monitoring the test. Understanding the complexities is necessary to improve the testing results and achieve similar reliabilities of single bar systems.

By Alan J. Lutenegger

A series of tension tests were performed on prototype scale steel pipe piles at two sites to evaluate the influence of scale and pile plugging on the unit skin friction developed in axial tension. The first site consisted of a clean medium dense fine sand above the water table. The second site consisted of a loose silty sand with the water table within about 0.5 m of the ground surface. Pile load tests performed at each of the sites included piles with diameters ranging from 73 mm to 114.3 mm, which may be considered driven "micropiles". At the first site, pile lengths of 6.1 m were used; at the second site, pile lengths of 9.1 m were used. Some of the piles were driven open-ended while others were fitted with a conical tip to form a closed end. During installation, pile plugging measurements were taken on the open-ended piles after each 0.30 m of penetration. The piles were allowed to rest for a period of about 30 days after driving prior to performing the axial uplift load tests to failure. The results indicate that in the medium dense fine sand the unit skin friction developed in tension is dependent on both the amount of plugging that occurs and on the size of the pile, which was not the case for the loose silty sand.

Jan 1, 2000

By Marcus Daubner

This paper explains how BAUER Spezialtiefbau GmbH uses digital methods on projects - starting from work preparation to completion of works. More precisely, the advantages of BIM-based planning during work preparation and the automated and structured data management - both machine production data and the manually recorded quality-relevant reports - during execution phase are displayed. In this context, the benefit of the digital twin to optimize processes, to reduce defect costs, for a more effective reporting sys-tem, and the further usage of as-built information in the BIM or GIS process is described.

Sep 1, 2022

By Hajialilue Bonab M.

The soil-pile interaction under lateral impact loads is not yet completely well known. Many tests on single piles under static lateral loads in centrifuge have been performed and P-y curves have been determined at different levels of the pile in soil. Following these static tests on piles, a large program is undertaken with the same piles submitted to impact loads. The pile equipped with various pile caps has been impacted under variable amplitudes of shock. The behavior of the pile under different impacts was studied and dynamic parameters of the soil-pile system have been determined. Many cases of loading constituting various load histories have been analyzed. They are resulting from parametric centrifuge tests run out, on the one hand with constant and cumulative impacts and on the other hand, variable and cumulative ones. The Influence of each type of loading was studied. Using a finite element method, a non-linear pile-soil system was conceived and a transient dynamic analysis have been performed. The results of the non-linear analysis and experimental data were compared giving a good agreement.

Jan 1, 2002

By G. G. Meyerhof

The paper reviews the state of the art of estimating the bearing capacity and settlement of pile foundations in sand and clay soils, including the effects of pile installation, scale effects of pile size and embedment and non-uniform soil conditions. The lateral resistance of pile foundations and effects of eccentricity and inclination of the load on the bearing capacity and movements of pile foundations in sand and clay are considered on the basis of some recent investigations.

Jan 1, 2010

By Rob van Dorp

Most traditional foundation designs are based on soil investigations using Standard Penetration Testing (SPT), sometimes combined with static load testing on sacrificial trial piles. However, this design approach has two major shortcomings. First, SPT data do not provide direct and continuous informa- tion about soil resistance as a function of depth. Second and more important, because of the relatively wide spacing between borehole locations, SPT soil investigations do not provide adequate information about variability of soil profile and/or soil resistance over the project area. Preliminary pile load testing on an SPT location can compen- sate for the first disadvantage but cannot address the second disadvantage. A design approach based on an adequate soil investigation campaign with Cone

May 1, 2022

By W. G. K. Fleming

The codification of foundation design and construction is a subject of extensive discussion in Europe and all current code proposals are based on limit state partial factoring. For simplicity, it is claimed, simplified forms of Partial Factor use are presently being advocated but, if this is the direction which codes are to follow, then it is preferable in this age of computer technology that a true system should be adopted rather than a simplification. A philosophically satisfactory method can readily be found which can fulfilcurrent requirements and it is better that such a method should be adopted from the beginning rather than later to find it necessary to make important alterations and amendments.

Jan 1, 1996

By S. L. Karunakaran

There are cases where it is found that a raft foundation would have adequate factor of safety against ultimate bearing capacity failure but the settlements would be excessive. Piles may be introduced in order to limit settlements to an acceptable level. The actual number of piles required to reduce the settlements to an acceptable level may be very small compared to the number of piles required to transmit the whole structure load. The paper focuses on the difficulties encountered in evaluating the load sharing between raft and piles. An elaborate analysis taking into account the interaction between raft, piles and soil is very complex and time consuming. Few approximate methods for arriving at a satisfactory solution to piled raft system are discussed in the present paper.

Jan 1, 1996

By R. L. Wei

The disturbing influences of pile driving on the surrounding soil mass, including the induced vibration, pore pressure and displacement of soil, were observed during the construction of pile foundations. It is shown that the effects of pile driving in saturated soft clay are tremendous and ought to be concerned attentively.

Jan 1, 2010

By Raffaella Granta

Mosul Dam is an earth fill dam located on the Tigris River, approximately 40 km (25 mi) northwest of Mosul, Iraq. The construction of the dam was completed in 1984. It is one of the largest multipurpose dams in the Middle East, and the largest dam in Iraq. The dam provides flood control, irrigation, power generation and water supply. At 113 m (371 ft) high and 3.65 km (2.3 mi) long, the reservoir has a storage capacity of 11.1 billion m3 (392 billion ft3) of water. The main hydroelectric power station has four turbines for an installed capacity of 750 MW. The discharge system includes two bottom-outlet tunnels of 10 m (33 ft) diameter, a five-gate service spillway and an emergency fuse plug spillway.

Oct 1, 2022

By L. Z. Xie

The results of the experimental study on the static behavior of single piles subjected to repeated and reciprocating axial loadings are recommended in this paper. Tests of four full-scale single piles of two different lengths under repeated loading and those under reciprocating loading have been conducted using the slow maintained load test method. All the eight piles were instrumented with strain gages located along the shafts. The study showed that for repeated loads below a certain critical value the total displacement of the pile top approached gradually a constant value. However, any repeated load greater than the critical value resulted a residual displacement per cycle, and that the reciprocating load capacity of a pile was dependent on the ultimate bearing capacity of the pile in tension and both were in the direct ratio.

Jan 1, 2010

By Ashley Shirer

Have you heard a geotechnical engineer rail against using the word "dirt"? The typical maxim is: "It's not dirt, it's soil!" This axiom is so prevalent that it is joked about on the construction site. How did we get to the point in our profession that soil is too technical to understand, while dirt is not viewed as important? Take a moment and think about the images that come to mind by the word soil. Responses range from the sand at a playground to the mud that sticks to the bottom of your shoe, the dark loam found in gardens to the firm earth under your feet. But do you know where the term soil originated? Or how it was intended to be used? This article looks at how word choice can lead to very different motivations for owners, designers and constructors.

May 1, 2023