Search Documents

By James Warner

Investigations of the sinkhole indicated that the loose, disturbed ground was completely encircled by dense competent core. This confinement substantially increased the effectiveness of the compaction grouting compared to what might have been expected at a "greenfield" site. However, the 8 ft diameter circle shown in the plan view was only the surface expression of the sinkhole proper and the deep, loosened ground actually extended to a larger diameter of about 20 ft. The planned spacing of the grout holes was based on the finite element simulations using a target void ratio of less than 0.3 throughout the compacted ground within a 5 ft radius of the grout injection point. Because of the strong confinement effect, the layout of grout holes included one central primary hole surrounded by six secondary holes at a triangular spacing of about 5 ft. Since the disturbed ground was considered a confined cylinder, it was anticipated that the primary hole would perform the majority of work and the secondary holes would act as check holes, with progressively lesser grout takes as the loose ground densified.

Feb 10, 2003

By Bernhard Bruggaier

Outside the oil and gas industry there is an increasing demand to install big piles for the foundation of ports, bridges, and wind-energy plants. This article introduces the design and techniques in using large MENCK pile driving hammers to install big foundation piles. Piles with a length up to 120 m, an outside diameter of 1.0 m to 3.15 m and weighing between 25t and 400t are being driven for these types of foundations. The required energy lies between 200 and 1700 kNm. Pile driving hammers that bring this amount of energy weigh from 38 to 300t and have a length between 10 and 20 m. Handling these big pile driving hammers requires a crawler crane on land or cranes on floating pontoons or jack-ups when working in water. Possible are either vertical or inclined piles, using a leader for inclinations up to 1:1.7 or up to 1:3 in a free riding version. Project descriptions demonstrate the versatility and practical use of the equipment under diverse operating conditions.

Jan 1, 2002

By Andreu J. Ferrero

Polyurethane and acrylate resins are routinely injected into soils to gain strength and control water flow. However, most published data regarding strength gain is derived from laboratory samples created under ideal conditions. This study endeavored to inject resins into full scale mock-ups that could then be excavated and tested to yield results comparable to actual field conditions. To achieve this goal, a large container was filled with a silty SAND (SM), as defined by the Unified Soil Classification System (USCS). The soil was moisture treated and compacted in lifts of 0.3m. PVC pipes installed in a diamond grid into the soil were used to inject polyurethane and acrylate resins. Dynamic cone penetrometer (DCP) tests were conducted on the polyurethane treated soils, the acrylate treated soils, and the baseline untreated soils in the container. Testing results will be correlated to SPTn and CBR values to evaluate increases in the soil strength parameters in the treated soils. Cored samples of polyurethane and acrylate treated soils will be tested in compression, shear, and triaxial. These laboratory test results will focus on material property gains for the treated soils, in comparison to standard values for similar soil types. Complete documentation of the soil type, compaction methods, injection methods, and testing performed have been documented and will be presented in the final paper.

By Haijian Fan

Currently, deep foundation designs for the service limit state are deterministic in nature. The settlements and lateral deflections of deep foundations are calculated by means of numerical techniques whereby the foundation-soil interactions are characterized by discrete load transfer curves such as t-z or p-y curves. The noted deficiency of the deterministic approach is that the uncertainties arising from various sources, such as soil properties and model errors are not considered. To address this deficiency, a performance-based reliability design methodology is developed using Monte Carlo statistical methods. The performance based design criteria are defined in terms of the specified allowable displacement. The input to the numerical solution techniques, including the soil strength parameters, unit weight of the soil are relevant to the generation of the load transfer curves are treated as random field. The well established random field generator algorithm, local averaging subdivision, is used to generate random samples of input, where the mean values, variances, the probability distribution, and correlation structures are required statistical parameters for these random variables. The objective of the performance based reliability design is to determine the optimized foundation dimensions so that the probability of failure is less than the target probability of failure. The probability of failure by the Monte Carlo approach is simply the ratio of the number of unsatisfactory performance to the sample size. A numerical example for laterally loaded drilled shaft is given to illustrate the application of the methodology. The incorporation of the correlation length is shown to be critical for properly accounting for the site soil spatial variability.

By I. K. Ozaydin

Analysis of piles groups loaded with large bending moments and both vertical and batter piles can be best performed by matrix analysis. In this paper, a case history about a tall marine control tower is presented. The soil conditions at the site and the results of the computer analysis of the piled foundation are summarized. It is shown that the pile loads are indeed less than the allowable load for a single pile. Pile head loads and moments are used in the analysis of the raft foundation.

Jan 1, 2010

By Armin W. Stuedlein, Seth C. Reddy

In this study, factors affecting the reliability of augered cast-in-place (ACIP) piles under axial compression at the serviceability limit state are addressed using a simple probabilistic hyperbolic model and a database of load tests on ACIP piles in cohesion less soils. The aleatory and model uncertainty in a selected load-displacement model is statistically characterized, and is used to simulate representative random samples from the bivariate random vector of model parameters. A first-order reliability method (FORM) was used to determine the effect of sample size on the stability and uncertainty of the reliability index. Sample sizes greater than about 40 provided relatively consistent estimates of the reliability index; however, its uncertainty continued to decrease with increasing sample sizes. Additionally, the effect of slenderness ratio on the reliability of the serviceability limit state design was characterized and found to exhibit a significant effect on the probability of exceeding a specified displacement.

Jan 1, 2013

By Meeok Kim, Thornton Tomasetti, Seth Knihtila, Michael Oakland, Shawn Leary

The transformation of Seattle's historic KeyArena into the state-of-the-art Climate Pledge Arena, home to the NHL's Seattle Kraken, was no small feat. The $930-million renovation and expansion required the near-total demolition of the old structure and construction of an 800,000 sqf (74,000 m2), below grade venue while keeping its landmarked façade and roof intact. To do that, the project team had to come up with solutions for excavating 680,000 cu yd (520,000 m3) of soil to make way for the new 17,000-seat arena while working around the massive temporary shoring supporting the 44 million lb (20 million kg) roof all in time for the NHL's 2021-22 season.

Sep 1, 2023

By James S. Graham

Marine design and construction methods are presented on the caisson foundations for the tower piers at the Brooklyn, Ben Franklin, Delaware Memorial 1st, Tappan Zee, Walt Whitman, Throgs Neck, Verrazano Narrows, Delaware Memorial 2nd, and Newport Bridges. All of the bridges are founded on caissons, bearing on bedrock, soil, or piling. Caissons at the Tappan Zee Bridge are partially supported by piling and partially by buoyant forces. General subsurface conditions for each are provided. The purpose of this paper is inform engineers how bridge foundations using caissons were built over major waterways in the Northeastern USA in the past, anticipating a surge of new bridge construction in the near future.

Jan 1, 2005

By Mamdouh Hamza

The construction of 1200 m length new quay wall located 1,300 m East of the existing Suez Canal bypass and about 1,000 m south of the Mediterranean shoreline is one of the main projects currently under development in Egypt. Due to very weak foundation soil, mainly soft clay, a particular effort, both in terms of design approach and construction feasibility, has been required. The execution of "barrettes" and T-shaped" diaphragm wall panels down to a depth of 65 m and under extremely severe soil condition has been required in order to pass through the upper soft soil and to reach a competent base layer. Very critical and variable hydrological conditions have been also encountered due to the contemporary nearby channel dredging activity, thus increasing the difficulty for maintaining the stability of the slurry trenches opened in soft material. This paper gives a general overview of the project with some emphasis to the most significant design aspects and to the construction of the deep foundation elements.

Jan 1, 2002

"This model specification includes sample text shown in normal font with commentary in italics. The commentary is intended to highlight project-specific items the specification writer should consider during development of the specification. In some sections, typical values are presented to indicate common practice, and these values may be changed to reflect project-specific requirements. The commentary should be removed before using the specification for a project. 1. SCOPE The work consists of designing, furnishing, installing, and testing helical piles used to support foundation loads (compression, tension and lateral), and any ancillary materials (e.g., load transfer devices, etc.) according to the project plans provided and these specifications. Unless otherwise noted, the installing contractor shall provide all labor, tools, equipment and materials necessary to install the required piles. The parties referred to in this specification are as follows: • The Owner is the property owner. • The Owner’s representative is the individual or firm hired by the Owner to design and oversee the overall project. • The pile designer is the individual or firm generally hired by the installing contractor to design the helical piles. • Installing contractor installs and tests (if necessary) the helical piles, and possibly tasks associated with the project. It is important to clearly define the roles and responsibilities of every party on each project to promote good communication and reduce potential for contractual misunderstandings. Different types of contractual vehicles (design-build, value engineering, etc.) require different roles and responsibilities for the various parties, which should be considered in specification development. The Owner will provide suitable access to the construction site for the installing contractor’s personnel and equipment. Unless specifically noted otherwise in the contract documents, the Owner will remove and replace any structures, utilities, pavements, landscaping or other surficial improvements in the work area as necessary to facilitate the work. The Owner will be responsible for overall construction oversight to minimize potential for developing unsafe conditions. The work may include post-construction monitoring of pile performance if required by the Owner or the pile designer to confirm performance of the piles subsequent to their installation. The work may also include installation of additional piles if the initial installation does not meet specified capacity or performance requirements. Responsibility for providing subsurface investigation shall be addressed in the bid documents. The Owner is responsible for providing to the installing contractor all available subsurface soils, rock and groundwater information and geotechnical testing data."

Jan 1, 2015

By Zhang Wengang, L. John Endicott

The properties of many geological materials are variable. This is especially true for variations in elevation of the top of rock profile, strength of weathered rock, and conductivity of rock masses. Often the site investigation stage is completed by site specific ground investigation utilizing boring, sampling, and testing. Statistically this is a sampling procedure, but the borings are often widely spaced, and ground conditions between borings are deduced by interpolation. Often budgets are a limiting restraint and the information that is obtained may be less than desired. Sampling and testing is often biased. If claims for unforeseen ground conditions are to be avoided, the properties of the ground should be adequately identified. This paper describes how data can be used to evaluate the subsurface top of rock profiles, and can give insight into representative, maximum, and minimum strengths, and variation in conductivity relating to inflow of water into excavations, that can assist in planning the works and also in resolution, or avoidance, of disputes about unforeseen ground conditions. INTRODUCTION The mechanical properties of the ground are naturally variable. The work of Geologists, Engineering Geologists and Geotechnical Engineers is fundamentally investigative. Frequently, budgets for ground investigation are squeezed, resulting in widely spaced boreholes, with conditions between them determined by interpolation. Profiling can be adopted but the measurement, such as seismic velocity, is used as an indirect means of computing in-situ profiles and mass properties. Often a lot of test data are generated on large projects or by many projects in the same vicinity. Published data enlarge the database for a given project, and databases can be interrogated to gain insight into different categories of ground. Integration with geological studies can then lead to more reliable characterization of the ground in terms of identifying the materials present, their extent and their range of properties. This paper focuses on properties of rocks that are generally required for ground engineering, namely the top of rock profile, the unconfined strength of rock materials, and the mass conductivity. Data are obtained from Granodiorite and Granite in Hong Kong, and from Granite and the Jurong Series of weakly metamorphosed sedimentary rocks in Singapore. All four rock types have been tropically weathered, resulting in widely varying top of rock profiles, material strengths and mass conductivity. With a wide range in values for these parameters, project specific ground investigation conducted within a limited budget may run the risk of falling short of obtaining sufficiently reliable data sets, resulting in risk that unforeseen ground conditions may be encountered.

Jan 1, 2019

By Arturo Ressi di Cervia

"The Construction of the Thrust Pits for Jacking of the I-90 Tunnel for the Central Artery/Tunnel Project (Part of Contract No. C09A4) in Boston MA was nominated for DFI’s 2002 Outstanding Project Award. In the judging, the project and the specialty subcontractor, Treviicos Corporation, was chosen for a Special Recognition Award. INTRODUCTIONBoston’s Big Dig, as the construction of the underground artery became known, is undoubtedly the largest urban construction project of this century.The Central Artery/Tunnel Project, or CA/T, to call it by its proper name, runs approximately eight miles through the heart of Boston, five miles of which are built underground while maintaining traffic on the elevated existing structure, while at its southern end I-90 is extended to Logan airport under active rail lines, Fort Point Channel and Boston Inner Harbor.Since the alignment of the road closely parallels the shoreline as it existed in colonial times, the cut and cover construction had to contend with substantial portions of filled ground, not to mention existing subway lines, live utilities, building foundations and, last but not least, the irritable Boston drivers and litigious adjacent property and business owners.Consequently, while it is impossible to single out the most difficult or challenging contract, the jacking of the tunnels of I-90 under the live rails of Amtrak certainly will rank high on the list.Never before, anywhere in the world, was an attempt made to jack tunnels of this size: the South Bay Interchange consists of three 78 feet (24 m) wide by 38 feet (11.6 m) high tunnels, the shortest of which is 167 feet (51 m) long. TECHNOLOGYIn order to achieve this engineering feat it was necessary to consolidate the soil under the track to prevent it from moving or settling during the jacking process. After a detailed analysis of the geological profile to be traversed it was decided that freezing was the most suitable method, since it could be applied to the full range of soils present on the proposed alignment."

Jan 3, 2003

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Edward C. Clukey

"Between 2008 and 2009, more than 6,000, 23-m long deep mixing method (DMM) elements were constructed to support 124 concrete mats comprising the foundations for the process trains for an LNG facility. The Owner requested first-of-its-kind analyses and assessments to confirm the quality and reliability of the DMM foundation. This paper provides information on these assessments and the procedures used to ultimately conclude that a fit-for-purpose foundation system was constructed.During early phases of construction, several DMM test cores revealed nodules of unmixed clay in upper core samples. A comprehensive review of available DMM core information was undertaken. It was concluded that the amount of coring being conducted as part of the contractor’s QA/QC program should be increased to achieve a foundation system with the required level of reliability.Three-dimensional finite element analyses were completed considering various distributions of defects in the DMM elements and the effects of potential downdrag on DMM elements. Calculated mat settlements and mat stresses were compared to cases without defects in the DMM elements. Various distributions of loaded and unloaded mat areas and number and position (both in the subsurface and laterally) of defects were considered. Four (of the 124) mats were identified as potentially “at-risk”. The settlement performance of these mats is currently being monitored and, to date, performance has been acceptable.IntroductionThe foundation support system for the process train at a major LNG facility comprises more than 6,000, 23-m long DMM elements. The general subsurface stratigraphy at the project site comprises (from the ground surface): (i) up to 8 m of fill sand initially placed underwater building to a stable construction platform; (ii) up to 12 m of soft organic clay (Unit II clay); and (iii) clayey sand and sand layers becoming progressively denser with depth (Unit III sands). Each DMM element comprised two secant 1.5-m diameter DMM columns. DMM elements were typically arranged as cells enclosing one, two, or three DMM elements."

Jan 1, 2017

By F. Keith Jacobson

To be involved in the construction of a deep dredged caisson for a major bridge pier is one of the most rewarding and professionally challenging experiences one can have in the bridge construction business. That experience was doubled in the construction of the two deep dredged caissons for the Highway 82 Bridge over the Mississippi River near Greenville, Mississippi. The challenges and the construction risks associated with constructing these two dredged caisson pier foundations highlight the construction engineering innovation associated with major bridge pier construction. The 1,378-foot Main Span of the Highway 82 Bridge makes it the longest cable stayed bridge span over the inland rivers of the United States. The main piers for this bridge are supported on two dredged caissons measuring 80-feet by 122-feet in plan, founding 200-feet and 170-feet below the river surface. The challenges of constructing these caisson structures, sinking them through 70-feet of water to the river bottom and then excavating and further sinking them to the founding grade without exceeding the design tolerances, were enormous. The construction engineering opportunities for innovation included major breakwater structures to create a friendly environment in 11 ft/sec currents, the first time use of Articulated Concrete Mattresses for river bottom scour control, unique air dome design to maximize the buoyancy of the caisson structure while floating, a caisson guide system to assure positive control and positioning of the caisson during the initial sinking phases, and a comprehensive sinking plan to assure maximum control and minimum risk. Many of the innovative solutions to the construction challenges on this bridge will be incorporated into future caisson construction projects on the lower Mississippi River.

Jan 1, 2013

By Eric Brandner

Expansive soil formations can be found throughout the United States. When subjected to wetting, many of these formations have the potential to swell and exert large uplift forces which can significantly damage lightly-loaded structures. Designing an economical foundation that can resist uplift forces is critical to prevent damage to these structures. The current solutions to control uplift due to swelling soils, such as over-excavation and replacement of the expansive material, or drilled shafts, can be costly and problematic. Piles made from recycled polymer materials may provide a solution. Due to a lower coefficient of friction along the interface than piles made from traditional materials, solid recycled plastic piles can allow expansive soils to move nearly independently from the pile when wetted. This results in a much smaller magnitude of uplift force being transferred to the structure which minimizes the risk of significant structural damage. This paper presents the preliminary results of research conducted on the use of recycled plastic piles in an expansive shale environment. The preliminary phase of the project involved the installation of six 13 in. (330 mm) diameter recycled plastic piles at a test site on the South Dakota School of Mines and Technology campus. The piles varied in length from 15 ft. to 25 ft. (4.6m to 7.6 m). Two of the piles were subjected to a full-scale compression load test in order to determine ultimate capacity, while the additional four piles are being subjected to long-term monitoring of uplift movement. A cast-in-place concrete pile, with a diameter of 6 in. (152 mm) and length of 15 ft. (4.6 m), was also installed at the test site for monitoring. The preliminary results indicate that the use of solid recycled plastic piles is a viable alternative for support of lightly-loaded structures in expansive soil environments.

Jan 1, 2009

By H. S. Radhakrishna

Foundations supporting power transmission and communications towers are subjected to both compression and uplift loads, often of a cyclic nature. Some novel foundations, combining the beneficial features of grouted and helix anchors with that of compression piles and grillages, were developed by Ontario Hydro during the construction of high voltage transmission lines in Ontario, Canada. In addition to meeting the load requirements, the foundations permit easy installation in swampy areas and also minimize impact on environmentally sensitive terrain. This paper describes the features of these composite foundations and outlines the performance criteria used for their design and installation on the basis of load test results.

Jan 1, 2010

By T. Matsui

Many existing bridge abutments on the soft ground laterally move and their many damage examples have been reported. An essential cause for the troubles of the lateral movements may be the lack of examinations for the lateral earth pressure acting on its foundation piles. In the present paper, actual movement condition of existing bridge abutments is first summarized, and then the author establishes a practical and systematical design method for bridge abutment foundation piles, including the examination for the passive pile.

Jan 1, 2010

By Anand J. Puppala

This paper provides information on various evaluation studies conducted to assess the CPT based interpretation methods. Salient findings from these evaluations are summarized. Additionally, a comprehensive evaluation study on both LCPC and European methods was performed on twenty-four driven piles selected from four different states. This evaluation showed that the LCPC method predictions are close to measured pile capacities. The European method provided good predictions for driven steel piles. Overall, both methods' predictions show high values of coefficients of variations, which are in agreement with other studies. Overestimation of driven concrete pile capacities is attributed to large estimations of unit point resistance. Suggestions to consider appropriate CPT based pile capacity interpretation methods are presented.

Jan 1, 2002

By Gordon Chen

As part of a value engineering envisioned by East Coast Slurry, Weidlinger Associates, Inc. designed a unique elliptical slurry wall cofferdam for construction of the 65 ft. deep MWRA North Dorchester Pump Station. A conventional rectangle cofferdam with multiple levels of bracing would have been time consuming and costly and imposed a significant obstruction to the pump station construction. A circular slurry wall, while eliminating the bracings, conflicted with adjacent structures and required excessive backfilling around the final pump station structure. The ellipse shaped cofferdam fit the needs of the project well; however, it created a significant design challenge without the use of bracings. Unlike a circular cofferdam which primarily only has hoop stresses, the ellipse still has to be designed for horizontal bending moments in each panel because of the non-axial symmetric conditions. The more eccentric the cofferdam shape; the higher the horizontal bending. The challenge was to develop a three dimensional finite element model that could analyze both the hoop stresses and horizontal bending stresses above and below the bottom of excavation induced by soil and water pressure and unbalanced construction surcharge loads. This paper discusses the techniques used to model the soils and structure interactions and results of stresses on this challenging unbraced configuration.

Jan 1, 2010

By Brett K. Mainer

In the summer and fall of 2007, Drill Tech Drilling and Shoring, Inc. designed and built three 24-foot inside diameter shafts in Northern California using soil mix panels for support. The soil mixing was performed using the Bauer Cutter Soil Mix (CSM) method, by which rectangular soil mix panels up to 71 feet deep were arranged in an overlapping manner to form a 24-foot inside diameter circle. The shafts were then excavated to depths up to 51 feet. One of the shafts was a test shaft and used only the soil mix panels for support. The other two shafts were located immediately adjacent to the Mokelumne River and were used as access pits for a microtunnel drive under the river. These two shafts had wide flange beams embedded in the panels and were supported with several levels of ring steel placed during excavation. This project was the first use of the Bauer CSM method in the United States. The CSM method has been used extensively in Europe and Asia, but never for this application and never with this high a loading criteria due to water head and microtunnel reaction forces. Soil conditions at the river crossing shafts consisted of sands, gravels, and cobbles over top of sandstone and conglomerate bedrock ranging in strength up to 5,000 psi. Groundwater was within several feet of the surface. The shafts were successfully completed between October 2007 and January 2008, and the microtunnel was successfully completed in February 2008. This paper provides discussion regarding selection of the shoring type, structural design, the soil mixing method, and the mix designs. Shaft construction, shaft performance, and the capabilities of the CSM equipment are presented.

Jan 1, 2008