Search Documents

A sample of fifty fractured low chromium-molybdenum alloy drill steel rods was investigated. Each rod was of the forged collar integral tungsten carbide type in common use in Australia.Examination of a new rod of the same type showed that a zone of spheroidized carbide about 0·25 in. wide was present about 12 in. from the shank end.Examination of the fractured rods revealed that 78 per cent. of failures occurred within 0·25 in. of the spheroidized zone at the shank end but in the main stem of the rod rather than actually in this softened zone where it might be expected to occur.This predominant type of failure at the shank end in the steel rods is caused by a highly anodic region corresponding to the first stages of spheroidization of carbides present in the steel. Accelerated corrosion in the narrow band havil\g this structure induces the formation of stress-concentrating corrosion pits, 78 per cent. of failures in this region being due to corrosion fatigue.The remaining 22 per cent. of failures, occurring in the as-rolled stem, were due to either corrosion fatiglie if failure were initiated at the water-hole surface of the drill rod, or to a decarburized outer surface if failure originated at this surface.Temperatures producing spheroidization were determined as 6007600C.Evidence suggests that approximately 75 per cent, of shank-end failures in all forged collar drill rods can be attributed to corrosion fatigue occurring preferentially in that section showing partial spheroidization of carbides· produced by the forging and hardeningoperations.Methods are suggested for reducing the frequency of fatigue failures in drill rods.INTRODUCTIONAn integral part of all tunnelling operations through rock is the drilling of suitably placed holes i:n.to which explosive is subsequently rammed and exploded.The drilling operation, whether for metalliferous mining or for general civil engineering constructional work; is...

Jan 1, 1955

By H Arvidson, V Chamberlain, R Marinho, B Parsons, T Rowl, M Noppé, M Mattera

With the introduction of CRIRSCO (2019) based mineral asset disclosure, Regulation S-K part 1300, 2019 (S-K1300) by the United States (US) Securities and Exchange Commission (SEC), applicable to companies listed on the New York Stock Exchange from 2021, Mineral Resource is now required to be reported Exclusive of Mineral Reserve, referred to here as ‘Exclusive Mineral Resource’ (EMR). EMR is equivalent to reporting Mineral Resource additional to Mineral Reserve, which has been permitted in jurisdictions outside the US for many years. Despite this, there are no practical guidelines in the literature or relevant reporting codes and rules for Competent/Qualified Persons to refer to, which creates a risk that disclosure of EMR estimates across the industry will be inconsistent and potentially ambiguous for analysts, investors, potential investors, and other stakeholders.With the introduction of CRIRSCO (2019) based mineral asset disclosure, Regulation S-K part 1300, 2019 (S-K1300) by the United States (US) Securities and Exchange Commission (SEC), applicable to companies listed on the New York Stock Exchange from 2021, Mineral Resource is now required to be reported Exclusive of Mineral Reserve, referred to here as ‘Exclusive Mineral Resource’ (EMR). EMR is equivalent to reporting Mineral Resource additional to Mineral Reserve, which has been permitted in jurisdictions outside the US for many years. Despite this, there are no practical guidelines in the literature or relevant reporting codes and rules for Competent/Qualified Persons to refer to, which creates a risk that disclosure of EMR estimates across the industry will be inconsistent and potentially ambiguous for analysts, investors, potential investors, and other stakeholders.

May 24, 2023

By G Simpson, S Dressler, A E. Levett

Tailings storage facilities often represent a mining operation’s most significant liability, posing serious environmental, social and safety risks. Almost all mining operations dispose of wet tailings (Valenta et al, 2023), which represents a risk of failure due to the potential for a rapid strength reduction of the unconsolidated materials leading to static liquefaction and subsequent dam wall failure. As a waste stream, tailings disposal, decommissioning and relinquishment aim to be inexpensive processes, ruling out many highly engineered solutions. Advantageously, tailings consolidation does not need to be immediate, opening the door for relatively passive, inexpensive consolidation methods that aim to gradually increase the strength of tailings over extended periods (ie years). In this paper, we present the prospect of novel in situ tailings stabilisation, learning from studies that have investigated the most erosion-resistant landforms on Earth.

Aug 2, 2023

By M Player, R Klug, N Schwarz

There are several technologies available for thickening and dewatering of mining process slurries. The most commonly used are thickeners and filters, but technological developments have made solid bowl decanter centrifuges a viable option and their use, as a modern and alternative technology, is being considered more and more. In terms of tailings, the main goal for all mine operations is to minimize operating costs and the environmental impact of the disposed material. The high potential risk of wet tailings storage in tailings dams is causing this technology to become unpopular, and there is a strong drive in many parts of the world, by governments, communities and environmental agencies to limit any further construction and use of such facilities. For the alternative disposal method of dry disposal of tailings, two aspects of the process have to be evaluated, namely the maximum dryness of the separated solids and the maximum liquid recovery. For most mining operations dry disposal is a new concept. Presenting these companies with examples of operations where this processing option has been successfully applied and proven, will help them to adapt to the changing requirements in the future. Focus has been placed on adapting decanter centrifuges to the mining environment. Modern decanters stand out in terms of their small footprint, low water demand, high availability and their high degree of automation, combined with the excellent cost / performance ratio. Decanter centrifuges have started to play a key role in applications such as tailing dewatering, drilling and tunnelling muds processing, hydrometallurgical processes of gold, nickel or zinc and separating crud in solvent extraction plants. This paper will present advantages of decanter centrifuges compared to the traditional technology and corroborate these advantages by case studies.

Jul 1, 2021

By Corbett GJ

The Bulolo Graben represents an intra-arc rift formed by activa- tion of transfer structures in an extensional setting formed be- tween the eastern and western sectors of the New Guinea Origin. Crustal thinning has facilitated the emplacement of dacitic Edie porphyry intrusions, locally as flow dome complexes, phreatomagmatic (diatreme) breccias and the Bulolo ignimbrite/ agglomerate as an extrusive equivalent of the Edie Porphyry. Gold mineralization is localized along intra-graben structures, com- monly at the intersection with cross structures and occurs in sub- sidiary dilational fractures and not the localizing major structures. Gradations are apparent in the styles of mineralization according to the degree of erosion of the hydrothermal system. Hamata occurs as the deepest mineralization of the quartz-sul- phide style Wau, Hidden Valley, and Edie Creek are dominated by carbonate-base metal styles. Kerimenge grades from quartz sulphide through carbonate-base metal to epithermal mineraliza- tion, the latter style also being present in the periphery of Edie Creek. Here, pre-existing fractures of the Edie Creek Structural Corridor have been reactivated by movement on NS structures to form the ore-hosting dilatant lodes. Fluid flow may have been from the vicinity of the Nauti diatreme margin and along the vein System.

Jan 1, 1997

By R Jacobs, J Yeates

"The Stockman base metals project is situated in State Forest in the alpine area of East Gippsland, Victoria, adjacent to a National Park and within the headwaters of a major Ramsar-listed wetland catchment and the Murray-Darling River system. Site topography is steep, and elevated (650 m – 1200 m above sea level), and subject to circa 1 m annual rainfall, with occasional winter snowfall. The project consists of two volcanogenic massive sulfide (VMS) deposits to be mined by underground methods and treated in a 1.0 Mt/a central concentrator to produce copper and zinc concentrates for export over a ten year operational life. New resource projects are rare in Victoria. Recognising the sensitive setting, planning for the Stockman Project, which is now in the advanced permitting stage, has focused on balancing economic, environmental and social outcomes to ensure social licence to operate is secured and can be maintained. This has involved close attention to triple bottom line (TBL) risks and outcomes. Stockman has successfully gained State and Federal approvals via the Environmental Effects Statement process. The process of obtaining these approvals has required close attention to effective stakeholder involvement, and management of a lengthy and difficult approvals process, which is still to be finally concluded. This paper is a case study of the process of that permitting and the issues encountered to date. Key learnings from the experience have included: successful approvals require close attention to much more than just the project and its technical aspects and physical setting – effective stakeholder involvement and endorsement is critical the differing consultation requirements for local, regional and government stakeholders, to design and plan implementation of a project to meet TBL objectives, and to gain social licence to operate within the Victorian approvals process, the need for an effective lead government agency with policy authority dealing with material policy change requiring post-closure financial sureties estimating realistic permitting time and cost during the project evaluation phase. CITATION: Jacobs, R and Yeates, J, 2016. Stockman base metals project – sustainability, social licence to operate and permitting lessons learnt, in Proceedings Project Evaluation 2016, pp 98–110 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By M English, M Yumlu

At times of high metal prices, mining projects that have previously been put into the ætoo hard basketÆ are now being more closely examined. Typically these projects include the potential recovery of small mineable tonnes with high contained metal values and often with poor ground conditions. For many underground mining projects, the drift and fill method is viewed as a high-cost method and a æmethod of last resortÆ. As a result the method is not well known in Australia and it is the authorsÆ view that the method is under utilised. The drift and fill method can be applied to a variety of underground mining situations and is a preferred method for some orebody geometries and where ore recovery is viewed as a key to project success. This paper examines some of the critical mine planning and backfill issues involved with the drift and fill mining method.

Jan 1, 2008

By A Harris, L Balzan

Accurate measurements of the moisture content of iron ore have increasing importance in modern mining operations. Knowledge of the moisture content allows process control actions to be carried out to ensure that the moisture is within prescribed limits, whether this is ensuring sufficient moisture to be above the dust extinction limit or that the moisture level is below the transportable moisture limit for sea shipments. Additionally, controlling moisture within desired limits can allow for greater throughput of iron ore by limiting the amount of water transported. There are a range of options available for operators wishing to obtain moisture data, though there are few demonstrated and proven devices that are able to provide real-time analysis of the full bed-depth of material. Scantech’s through-belt moisture systems are able to accurately analyse the full bed-depth of conveyed iron ore in real time using its unique microwave transmission technology, providing valuable data for operators. Recent advances in these systems have overcome errors associated with the highly attenuating nature of iron ore, particularly for large conveyor belts and deep ore. Furthermore, analysis of different ore mineralogy and its effect on the accuracy of moisture analysis has been examined and quantified. This paper discusses some of these recent results, demonstrating achievable accuracies in spite of changing ore mineralogy. Scope for future work is also briefly discussed, concluding the paper.CITATION:Balzan, L and Harris, A, 2015. Real-time through-belt moisture analysis for iron ore, in Proceedings Iron Ore 2015, pp 539–542 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By G Brooks

The control of phosphorus in steelmaking is one of the famous challenges of pyrometallurgy. It is well established that highly basic slags, the presence of FeO in the slag and lower temperatures (less than 1650°C) are favourable for phosphorous removal. The thermodynamics of this reaction have been extensively studied under laboratory conditions and the general trends confirmed through industrial trials. However, in general, phosphorus slag/metal distributions measured in industry are far from equilibrium and quite specific to the oxygen steelmaking technology being used. This variability was quantified by Urban, Weinberg and Cappel (2015), who found that the phosphorus partition ratio measured in plants varied with blowing practice, stirring intensity and even converter life. Some recent kinetic studies by Gu, Dogan and Coley (2017) have shown how the kinetics of these reactions vary with FeO content and dissolved sulfur at the droplet scale. A global kinetic model by Rout et al (2018) provides meaningful predictions of where dephosphorisation occurs in an industrial basic oxygen furnace (BOF) and some recent heat transfer modelling by Madhavan et al (2021, 2022) implies that temperature difference between droplets and slag has a role to play in explaining why equilibrium is not achieved. This paper will review the current state of knowledge and provide suggestions on predicting phosphorous removal for industrial operations and how greater removal could be achieved.

Jun 19, 2024

ABSTRACT' The first references to gold in New Guinea were by the Portuguese in 1525. The first significant discovery and gold rush was on Sudest Island in 1888 and was a natural extension of the rush that surged up Australia's eastern coast and ended at cook- town. Prospectors made a series of minor discoveries in coastal regions before the first large discovery at Wau/Edie Creek/Bulolo in 1925. Major post war gold discoveries were made at Bougainville, Frieda River, Porgera and Ok Tedi. On Misima Island a large bulk low grade deposit has been recognised surrounding old gold workings. Gold exploration has increased drama- tically since the lifting of a 3 year moritorium on new exploration areas in Noverrber 1982. A new bulk low grade gold discovery has been made on Lihir Island, north of Bougainville and a number of other promising areas are being drilled. Gold production is also expanding dramatically from current levels of 600,000 ounces to an anticipated 1.3 million ounces in 1985 with the opening of Ok Tedi. Other potential developments are likely to increase output above 2 million ounces by 1990. Papua New Guinea's world ranking as a producer is likely to move from 9th to 7th in 1985 reflecting the favourable geological potential, stable political environment and attractive development terms offered by the Government.

Jan 1, 1984

By M Monaghan, B S. Gregory

The Geita Gold Mine is located 80 km southwest of the town of Mwanza in the north-west of Tanzania and is 100 per cent owned by AngloGold Ashanti Limited. Open pit mining commenced at Geita in 2000. In 2011, the operation produced 494 000 oz at a cash cost of US$536/oz. This is a significant improvement from 2008, when 264 000 oz were produced at a cash cost of US$742/oz.A period of relatively poor operating performance at Geita was recorded over the period from 2006 to 2009. A period known at Geita as æthe turnaroundÆ commenced in 2009, and has been remarkable to say the least. Over the last couple of years the mine has embarked on a journey, which saw various interventions and initiatives. Among the key initiatives were Project ONE (which focuses on business process framework, systems for people and safety transformation), asset integrity, fatigue management and contract mining of satellite pits.Since the commencement of the turnaround at Geita, gold production has matched market guidance. The mine has returned to positive cash flow on the basis of strong performance on cash management, improved production and increased gold price.This paper explains some of the details of the mine operationsÆ improvements, how they were implemented, their relative contributions to improved mining performance and the path ahead to best practice. Observations will be made about some improvement rules that can be applied generally in open pit mining.CITATION:Gregory, B S and Monaghan, M, 2012. The path to best practice at Geita Gold Mine, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 41-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

Gold deposits in Eastern China have characteristic of belted distribution. The concentrating belts of gold mineralization are about parallel to the island are belt in Western Pacific Ocean. Gold deposits are mainly concentrated in the aged metamorphic rock series on the upwarping zones and upwarping fault zones, and obviously controlled by the deep fractures and their deriva-tive secondary faults. Gold mineralization had genetic relation to the Mesozoic (especially Yanshan period) magmatic activity. The distribution and genesis of gold deposits can be explained by the assumption of wavy structure. The formation of wavy structure is related to the process of Pacific plate and India plate.

Jan 1, 1990

By Lunarzewski L

Gas problems, largely instantaneous outbursts of coal and gas, arose in the early days of coal mining in Australia, leading to attempts at predrainage often including destressing. With deeper mining and new gassy areas being mined, gas problems have increased. This has led to more research, such as into coal-gas relationships, and more practical trials into seam gas drainage in both the Sydney and Bowen basins. Predrainage techniques have been devised to suit the special Australian geological conditions and to take into account the erratic occurrence of CO, (nearly 100 per cent in some cases) in the seam gas. Better mining methods and other improvements are continuing. The introduction of post-drainage has been simplified by the adaptation of long established overseas techniques and equipment.Utilisation of seam gases in Australia is complicated by the presence of CO, but even with pure CH. little has been done.Seam gas drainage has some disadvantages such as the need for, and the dangers of, complex and rigorously controlled plant. Also drained coal becomes harder and dustier.

Jan 1, 1985

As mining and extraction processes improve and lower grade ores become economic, mining for most ores have extended to depths beneath the zone of weathering oxidation created over geological history. These deeper openings expose sulphidic formations and reduced mineral species as either primary ore or simply as accessory or gangue minerals in the country rock. This is not new, underground mining for primary base metal and gold have long been familiar with these problems, as have coal and uranium miners. The change is simply that the number of mines exposing sulphidic waste rocks, tailings to the atmosphere and/or leaving behind dewatered sulphidic rock surrounding the mine void has increased the number of sites from where acid mine drainage (AMD) may emanate with consequential problems for the hydrological environment including downstream catchments (Miller et al, 1996). The principles of ecologically sustainable development (Brundtland, 1987) have been more or less ratified by all the developed nations of the world and this has led, amongst other things, to an expansion unprecedented in the research and documentation of means for achieving long-term environmentally acceptable stabilisation of solid wastes of all sorts. These have revealed that AMD problems can be minimised and even reversed in many cases by the integration or co-disposal of biodegradable organic wastes with oxidising sulphidic wastes (Elliott et al, 1996). This paper considers how this might be achieved at mine sites in Australia and the results encountered at some relevant sites.

Jan 1, 1997

The Melanesian Outer Arc, extending from. Papua New Guinea to Fiji, developed as a result of interaction between the Australian and Pacific plates throughout the Tertiary, and the following stages are recognized. ,a, Formation of island arc tholeites above a west facing subduction zone in the Lower Tertiary. fit Emplacement of mainly calcalkaline volcanics above an east facing subduction zone in the Upper Miocene and Pliocene. ontinued east facing subduction coupled with fragmentation of the arc from the Pliocene onward. Alkaline and Mg-rich volcanism occurred in addition to continued calcalkaline activity. Tre Upper Miocene and younger volcanism is into five arc segments on the basis of geographic position and nature of the magmatism. The calcalkaline Bismarck arc extending along northern New Britain and including small islands to the west. The alkaline Tabar to Feni arc, north of New Ireland. The Solomons arc, including Bougainville and the western part of the Solomon slands. Volcanism is largely _.alcalkaline, but Mg-rich varieties occur the Solomon Islands. roe New Hebrides arc, extending from the -astern Outer Islands of the Solomons through Vanuatu. Both calcalkaline and :alkaline volcanics are representeo. alkaline and calcalkaline Fiji arc.

Jan 1, 1987

By Y Li, D J. Williams, E Topal

A mine waste rock dump does not have any intrinsic value, yet is an inevitable structure in surface mining operations. Since the purpose of mining is to maximise profit, possible expenditure reduction in hauling waste rock to the dump, which can represent up to 50 per cent of the total operating cost, is highly desirable. Apart from cost, potential acid mine drainage (AMD), due to seepage from surface waste rock dumps containing reactive waste rock, could threaten the ecological balance, drinking water supplies and irrigation systems downstream from a mine site. In order to minimise these potential risks, selective placement of benign and reactive waste rock, and the encapsulation of reactive waste rock by benign waste rock, need to be carried out during the construction of the rock dump.In this paper, a new methodology, based on mixed integer programming (MIP) is developed to manage waste rock dumping. The model aims to minimise waste rock haulage costs by locating the optimum destination(s) for each waste rock block, while at the same time controlling the placement of reactive waste rock to minimise the potential for AMD. Tests on small-scale virtual data demonstrated that the model is capable of dealing with selective placement of different waste rock types, encapsulating reactive, potentially acid forming (PAF) waste rock, and stockpiling benign waste rock for encapsulation and rehabilitation purposes. The solution time for the MIP model is far less than the traditional manual approach, and the resulting schedule is up to 46 per cent more cost effective.CITATION:Li, Y, Topal, E and Williams, D J, 2012. Mathematical approach for better mine waste rock dumping management, in Proceedings Life-of-Mine 2012 , pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By L E. Howard

Micro-computed tomography (Micro-CT) is an X-ray imaging technique that produces high-resolution 3D computerised ‘virtual’ models of geological specimens based on the X-ray attenuation of different materials in the specimen. The ‘virtual’ specimens are made up of voxels, the 3D equivalent of pixels, each assigned a gray value based on X-ray absorption. Micro-CT has enormous potential for allowing non-destructive, digital analysis of structure and composition when the mineralogical phases can be digitally separated. However, variation in X-ray flux between scans results in highly variable grayscale values for identical materials. Consequently, materials usually have to be segmented manually, which is subjective, inaccurate, labour-intensive and time consuming. Here we present a protocol and imaging software package that can be used to accurately and precisely extract quantifiable information in a repeatable and objective fashion. The software will allow the separation, visualisation, measurement and analysis of spatial and volumetric distribution of different mineral phases without damaging the specimen. This paper explains the potential use of this protocol and software package to ultimately allow automatic segmentation and quantification of gold in drill core samples, removing subjectivity and inaccuracies from data processing.

Sep 5, 2011

By Box JC

A comprehensive computer simulation has been developed for heap and dump leaching processes. It deals with complex chemical interactions, involving several minerals and reagents, which vary with time and location in the dump. The simulation is generally applic- able to ores of various metals extracted by different reagents. It requires only mineral- ogical data obtainable from drill cores and chemical data obtainable from the literature; there is no curve-fitting with adjustable parameters. Applications in designing testwork programmes, evaluating operating options, transferring experience to new situations and reducing uncertainty in long-term forecasts are described. Specific examples are included illustrating the potential of the simulation.

Jan 1, 1983

By J Rock, K Bambrook

"Hanwha Mining Services was approached by Glencore Coal to provide a series of (trial) demonstration blasts at its Clermont coalmine. The intent of the project was to trial a bulk explosive product that would be able to provide sufficient energy for the ground type encountered without production of post-blast fume. Three blasts were loaded using the patented XLOAD bulk explosives with a density of 1.00 g/cc. XLOAD bulk products are water resistant explosives that can be loaded at densities much lower than traditional (generic) water resistant heavy ammonium nitrate – fuel oil (ANFO) or pumped blends with significantly reduced risk of fume. In addition, these products have detonation characteristics that generally deliver a higher heave partition than conventional bulk products and hence improve muck pile looseness and digability.The priority key performance measures included the absence of fume from blasting, being at least cost neutral and providing similar if not improved shovel dig rates. The design for the initial blast took a conservative approach to ensure the key blast outcomes of fume control and fragmentation were achieved.The second blast used the same pattern dimensions as the benchmark bulk product used in this area to provide a cost neutral comparison with the benchmark products that had been used over the prior six months. This resulted in a 20 per cent lower powder factor than would have otherwise been used. To test the suitability of XLOAD, this shot was slept for over two weeks between loading and firing in geology where the sleep time is typically kept to a few days to minimise the fume risk.The third blast utilised a slightly larger drill pattern to push the capabilities of XLOAD and provide a cost neutral comparison between the trial product and the traditional benchmark products. All three blasts were fired with no fume observed, no recordable incidents and good fragmentation. Shovel productivity from all three of the trial blasts was excellent with higher average instantaneous dig rates being recorded (average six per cent improvement against the instantaneous dig rates recorded for the benchmark blasts).Citation:Rock, J and Bambrook, K, 2016. Controlling Blast Related Fumes with Unconventional Explosives, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By S Henderson

The Otago Goldfield has produced approximately 8 million ounces of alluvial gold and over 2.5 million ounces of hard rock gold and is currently home to New ZealandÆs largest producing gold mine. In the eyes of explorers this production history makes the goldfield a good place to explore.   Modern exploration in the Otago Goldfield commenced in the late 1970s with the exploration for tungsten. However, a rapid rise of the gold price in the early 1980s saw the focus shift to the exploration for gold which lead to the discovery of the Macraes Gold Project in 1984, which since it came into production in 1990 has been New ZealandÆs largest producing gold mine. With the exception of the Macraes Gold Project, exploration continued in the Otago Goldfield for a further 20 years without further success.   In 2006, Glass Earth (NZ) Limited (Glass Earth) reviewed all the exploration technologies applied to the Otago region and available geological data, including the 1996 OceanaGold Helicopter Electro-Magnetic (HEM) data, and concluded that combined magnetics and HEM were able to delineate the Hyde Macraes Shear Zone (HMSZ) which hosts the Macraes Gold Project. Unlike previous explorers who explored the Otago region in a piecemeal manner, Glass Earth opted to collect a new, region-wide dataset which could be integrated with all previous collected geological information to come up with new exploration concepts and targets. As part of this process, Glass Earth applied in mid 2006 for New ZealandÆs largest on-shore gold Prospecting Permit, PP39-322 which was subsequently granted in November 2006. In mid January 2007, Glass Earth commenced acquisition of approximately 50 000 line kilometres of HEM data, making the Otago regional aerial geophysical survey (survey) the largest aerial geophysical survey ever undertaken in New Zealand.   This paper will report on the progress of the Otago Regional aerial geophysical survey and outline some of the preliminary findings from what is still a work in progress.

Jan 1, 2007