Search Documents

By Grano S. R, Lauder D. W

Investigations on the oxidation behaviour of chalcocite and its rejuvenation by hydrogen sulphide ion have been undertaken. Chalcocite oxidation was measured using X-ray photoelectron spectroscopy (XPS), zeta-potential and by dissolution in et

Jan 1, 1997

By H Wright

Black Rock Cave (BRC) is a sublevel cave which was developed in 2018–2020 and has been in production since November 2020. BRC is part of the Mount Isa Mines complex and extracts a leached orebody comprising of high-grade chalcocite ore, situated below the historic Black Rock Open Cut workings. The mine is owned by Mount Isa Mines and operated under contract with PYBAR Mining Services. In 2021 a number of rockfalls occurred throughout the mine and were increasing in frequency. This culminated in a major rockfall on the decline in June 2021, after which the decision was made to withdraw all persons from the mine, initiate rehabilitation and conduct further investigations to deduce a safe method to provide long-term support. The rockfall investigations have shown that the corrosive nature of the highly leached rock mass can consume a split set in less than 18 months. A review of potential corrosion resistant ground support methods concluded that steel split sets have a safe lifespan of six months at BRC, and that all workings must have corrosion resistant support installed prior to exceeding the safe life of the friction bolts. The review recommended the use of 4 m cable bolts as the most suitable method of corrosion resistant support. This new support system, and the requirement to rehabilitate all mine workings within the leached orebody, had an impact to the schedule and an effect on both equipment and manning levels at BRC. Accelerated jumbo rehab allowed access to the production levels within two months of the rockfall. Cable bolting then followed the jumbo bolting in all leached areas. The direct impact has been ten months of reduced production, due to night shift closures of the decline to enable cable bolting. The impact to the mine has been minimised by the small flexible team that enabled the mine plan to change rapidly and often to accommodate the challenging conditions. In less than two months from the rockfall event, production had resumed. Within ten months of concluding that the mine required; full rehabilitation, a new support system and a full re-schedule, normal mining operations had restarted, with pre-event productions rates being achieved.

Mar 29, 2023

By K Henley

One of the greatest practical difficulties of measuring airblast occurs when a significant wind is blowing onto the microphone. Small windscreens are usually used to mitigate the wind noise on the microphone, but in some wind conditions, sound pressure levels (SPL) of over 120 decibel (linear) are frequently recorded. There are no specific procedures to mitigate the effect of wind noise when measuring airblast in any of the standards or guidelines pertaining to the measurement of airblast from blasting operations, other than the requirement to use an effective windscreen. A search for relevant literature was undertaken and measurements were taken over a period of six months at a test site using alternative microphone measurement methods. Previous researchers’ experiments with windscreens in silenced wind tunnels showed that wind noise can be reduced through the use of large diameter windscreens, and that at low frequencies, the windscreen size and the material type makes no difference to measured SPL values. Other researchers found that wind turbulence caused significant SPL measurement problems. A comparison with field data failed to explain the extremely high SPL recorded by the field microphones at wind velocities much lower than those used in wind tunnel testing. It has been concluded that turbulent airflow over and behind the microphone is a significant contributor to extraneous noise in airblast measurements in windy conditions. This turbulence can be generated by objects upwind of the microphone or by the microphone itself if the windscreen is ineffective. Reducing the wind speed over the microphone by placing it on the ground is the approach required by the international standard for the measurement of noise from wind turbine generators (IEC 61400–11). This paper presents data that illustrates the extent of the problem, reports on the trial of three different microphone mounting locations for measuring airblast from blasting and concludes that in windy conditions, microphones placed on the ground substantially avoid wind problems and do not reduce the measured SPL of the airblast.CITATION:Henley, K, 2015. Reducing the effect of wind on airblast measurement during blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 485–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Zichenko ZA, Volkov SV, Shaluhina LM, Emelyanov AF

A method of selective gold recovery from black sands has been elaborated which is based on the liquid phase low temperature chlorination of materials. A liquid agent mixture of sulphur monochloride S2C12 and sulphur dichloride SC12 is used. This method ensures the gold extraction either in the state of AuC13.SC14 complex salt solution or as metal. The kinetics and main physico-chemical parameters of the process (eg density, solid: liquid ratio, temperature) have been investigated. The materials investigated were quartz-insipid ride samples with low sulphur and high iron (up to 70 per cent Fe2O3) contents. Gold recovery is 96 - 99 per cent at temperatures not exceeding 100¦C. Most of the associated minerals remain in the cake. To obtain metallic gold, the resulting solution of the AuC13.SC14 salt after leaching is reduced by hydrazine with subsequent annealing. The elaborated method is remarkable for small energy expenditures owing to low process temperature and a high gold dissolution rate. The solution of sulphur chlorides and other reagents are used in closed cycle.

Jan 1, 1993

By M Allen

By its nature, the mining industry is energy and emissions intensive. In the future, the world will still require the outputs of mining but the industry will need to adapt to the low emissions economy. Understanding the risks of climate change to a particular site or at a company level is key to managing this transition.CITATION:Allen, M, 2018. Assessment of climate risk in the Australian mining industry, in Proceedings Life-of-Mine 2018, pp 13–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By E Bouchard March, F Lavoie, B Legare, K Bourassa

Quebec Iron Ore (QIO), a subsidiary of Champion Iron Limited (Champion), completed the restart of the Bloom Lake iron ore mine located in the heart of the Labrador Trough region of Northern Quebec, Canada in February 2018. Prior to its restart, the concentrator flow sheet underwent major upgrades which brought the iron recovery to the highest of all Labrador Trough operations. After two profitable years of production, QIO, supported by Soutex, started to look at technologies to improve its current performance and integrate into its expansion project flow sheet. From the lessons learned while optimising Phase 1, the addition of a scavenger-cleaner processing stage was identified as an improvement opportunity to increase recovery, produce a higher-grade product, and further improve the stability of concentrate quality. In 2019, the NI-43101 feasibility study for the Phase 2 expansion, aiming to double the production of high-grade iron ore concentrate, was published. Based on the metallurgical test work, the hydraulic classifier was selected to perform the scavenger-cleaning duty for its well-established performance and known behaviour at the cleaning step in the Phase 1 plant. To validate laboratory results, a pilot scavenger-cleaning hydraulic classifier was installed in Phase 1. Although the hydraulic classifier was selected for the feasibility study, metallurgical test work performed with the REFLUX® classifier showed interesting potential. It was thus decided to also install a pilot RC300 Reflux classifier at the scavenger-cleaning stage in Phase 1. Despite their apparent great similarities, the metallurgical performance was significantly different, and many dozens of sampling campaigns highlighted the different performance of both pieces of equipment considering the feed material particle size. This article presents the pilot plant results in terms of recovery, selectivity and stability for both the Reflux classifier and the hydraulic classifier operated in a scavenger-cleaner stage at the Bloom Lake iron ore concentrator.

Nov 8, 2021

The discovery since 1990 of four major orebodies in the Mt Isa Inlier - Century Zn-Pb, Osborne Cu-Au, Cannington Pb-Zn and Ernest Henry Cu-Au - only serves to enhance the already high stature of the Inlier in world mining importance. Currently the known mineral resources of the Inlier represent about 11 per cent of the world's Pb-Zn resources, five per cent of the world's Ag resources, and one per cent of the world's Cu resources. More can be expected to be added to these impressive figures given that two-thirds of the Inlier remains obscured by younger cover. Individually, projects such as Century and Cannington may ultimately achieve `world's best' status; Century's proposed production of 450 000 tpa of Zn metal would rank it close to number one with Cominco's expanded Red Dog project in Alaska. Cannington, with projected production of 660 tpa Ag, could become the world's biggest producer of silver. For comparison, Mt Isa produced 170 000 t of zinc metal and 335 t of silver in 1995. The apparent physical diversity of deposits in the Mt Isa Inlier is matched by a great diversity of opinion as to their origins. Because Ernest Henry is hosted by `porphyries', it is described by some as a porphyry copper deposit, despite mineralisation age possibly post-dating volcanic age by 200 Ma. Cannington Pb-Zn could be a Broken Hill-type (BHT) exhalitive deposit, or a late epigenetic replacement `regional skarn'. Mt Isa - Hilton Pb-Zn deposits appear to have experienced all deformational events and he syn-diagenetic in origin, or may have experienced little of the above and be epigenetic replacement deposits formed late in the major Isan orogeny, some 150 Ma after deposition.

Jan 1, 1996

By H Arvidson, A Walker, N Pollock

Following the recent tailings tragedy in Brumadinho, the Investor Mining and Tailings Safety Initiative was formed representing institutional investors in the mining industry. This Initiative, led by The Church of England (CoE), requested data from 726 mining companies on each of their Tailings Storage Facilities (TSFs). What this exercise confirmed was that there was no public database of TSFs, and that there was a clear gap in tailings management systems within the disclosing companies. We present an approach using technology to support best practice TSF management, governance and disclosure which was originally submitted as part of University of Cambridge Post-graduate studies in Sustainability Leadership in January 2020. The aim of the paper is to discuss how technology could be used to deliver a Tailings Management Solution (TMS) that is aligned with the Global Industry Standard on Tailings Management (GISTM), and supports rigorous governance leading to disclosure. Subsequently the goals of the plan are aligned with that of the co-conveners of the GISTM (the International Council on Mining and Metals (ICMM), Principles for Responsible Investment (PRI) and United Nations Environment Program (UNEP)) which is to facilitate operators’ trajectory towards zero harm to people and the environment. Most of the focus to date around tailings management post Brumadinho has been on monitoring technologies, of which there are many. It is obviously important to acknowledge the critical role of monitoring technologies; however, our approach is agnostic to monitoring technologies and assumes that all of them are relevant. Our focus is on the data management, reporting and governance leading to disclosure of the information. Critical components of developing the TMS include adapting existing software products and solutions, recognising a system thinking approach is needed, strategic partnerships to deliver an accessible solution faster and more cost effectively, and, new ways of collaborating. The TMS should also accommodate relevant regional geotechnical codes and standards. The industry need for a TMS is well established and urgent, with significant pressure from regulators and civil society for the industry to address this significant issue.

Jul 1, 2021

By N Dube, K L. Sandvik, C Mutevhe

Trojan Nickel Mine is the largest producer of Ni, Cu and Co in Zimbabwe. The mine has operated a nickel flotation concentrator and base metal refinery continuously since 1969, creating 28 million tonnes of sulfide bearing tailings, five million tonnes of permanent waste rock and about seven million tonnes of smelter slag. Exposure of the sulfide bearing minerals renders them susceptible to oxidation in the presence of water and oxygen, resulting in acidic solutions with elevated concentrations of total dissolved solids, sulfate, metals and residual flotation chemicals in various waters draining from the mine site. These pollutants pose a direct threat to the environment and human health, and understanding their deportment and behaviour in the various waste streams is essential in the mineÆs environmental objectives to prevent or minimise adverse impacts arising from its operations. A geochemical assessment of the pollutants was carried out to compute a mass balance between the major sources of pollution and the distribution and fate of pollutants in waste streams from the mine site. Waste rock, tailings, surface water, ground water and sediments were sampled, tested and analysed. Mineral composition and water chemistry data show that geochemical reactions are responsible for the release of pollutants from waste rock, tailings and plant spills. Drainage from the mine area is near neutral due to buffering by magnesium carbonates in the fine fraction of the tailings. The natural wetlands that exist downstream of the waste rock and tailings dams are effective in reducing metal loadings to water courses. However, solutes and heavy metals are occasionally released to surface and ground water, when their concentrations peak during the dry season. The results demonstrate the necessity to understand the natural chemical processes that characterise the distribution of pollutants in nature and how such knowledge can be used to develop cost effective methods to remediate pollution in the natural environment.

Jan 1, 2006

By Akerkar D. D, Dey M. L, Mathur S. B, Chowdhury S. K R

The extraction of gold and silver from chalcopyrite concentrates has been investigated. In view of the recent interest in non-cyanide leachants for gold and silver, one such alternative reagent, namely thiourea, has been employed in the present work. Precious metal leaching was attempted from received copper concentrates as well as pre-oxidised concentrates. Pre-oxidation of the concentrates was carried out by three different methods, namely roasting, pressure oxidation and biological oxidation. After pre-oxidation and leaching of the base metals, the leach residues were subjected to further leaching for precious metal extraction. The results obtained on the extraction of gold and silver from received concentrates as well as pre-oxidised concentrates are presented and the effectiveness of the three pre-oxidation routes employed is compared.

Jan 1, 1992

By Kelly D, Moore C

The Golden Mile, which has been mined continuously for the past 100 years by both underground and more recently open pit methods, occupies an area of 1.2 km by 4 km adjacent to the city of Kalgoorlie Boulder in Western Australia (Figure 1). Large-scale open pit mining at the Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston operations is currently extracting 7.8 million tonnes of oxide and sulphide ore for a total production of 522 000 oz per annum. The effectiveness of grade estimation techniques at KCGM has been examined with reference to existing 10 m bench sample data from all operating areas within the Eastern Lode System of the Main and North pits. The aim of the study was to recommend practical parameters for grade control estimation. The review included comprehensive variography and comparison of nonparametric estimation methods (Joumel, 1983) such as indicator kriging and probability kriging with ordinary kriging, leading to the development of improved grade control parameters and procedures for both daily quality control and short term mine planning. This paper reviews the geological, statistical, geostatistical, mining and modelling features studied in order to present KCGM's Mining Department with recommendations for improving grade control.

Jan 1, 1994

By P M. Cepuritis

In hard rock mining, large-scale bulk mining methods such as block or panel caving (BC/PC) and sublevel caving (SLC) typically generate significant surface deformations such as subsidence. Surface deformations need to be considered in the project evaluation and planning stages of cave mines, for example, planning and location of critical underground mine planning infrastructure such as portals, haulage and vent shafts, access roads, or potential damage to existing infrastructure, changes to surface water management, waste dump, stockpile and tailings dam stability, and environmental impacts. Assessing the impact and risks associated with subsidence is a key component in robust mine planning and operations management.

Nov 29, 2022

For too long we, as an industry, have borne the brunt of irrational claims, poor science and even worse, journalism with regards to our affect on the environment. To some of us, the overwhelming media attention on greenhouse warming, the polluting outputs of mineral processing or unthinkable depletion of natural resources has left us embarrassed and more unfortunately has turned bright young people away from a career in the minerals industry.This paper shows the hypocrisy associated with an element of the green movement and dispels some general myths on mining disseminated by radical environmentalists.The fallacy of the greenhouse warming effect will be scrutinised by common sense and the mining industryÆs use of land will be discussed and put in proper perspective.Problems associated with safety and emissions and the means to overcome such are discussed briefly.

Jan 1, 2004

By A Woodley, G Keir

The mining industry faces concurrent pressures of reducing water use, energy consumption and greenhouse gas (GHG) emissions in coming years. However, the interactions between water and energy use, as well as GHG emissions have largely been neglected in modelling studies to date. In addition, investigations tend to focus on the unit operation scale, with little consideration of whole-of-site or regional scale effects.This paper presents an application of a hierarchical systems model (HSM) developed to represent water, energy and GHG emissions fluxes at scales ranging from the unit operation, to the site level, to the regional level. The model allows for the linkages between water use, energy use and GHG emissions to be examined in a flexible and intuitive way, so that mine sites can predict energy and emissions impacts of water use reduction schemes and vice versa. This paper examines whether this approach can also be applied to the regional scale with multiple mine sites.The model is used to conduct a case study of several coal mines in the Bowen Basin, Australia, to compare the utility of centralised and decentralised mine water treatment schemes. The case study takes into account geographical factors (such as water pumping distances and elevations), economic factors (such as capital and operating cost curves for desalination treatment plants) and regional factors (such as regionally varying climates and associated variance in mine water volumes and quality).The case study results indicate that treatment of saline mine water incurs a trade-off between water and energy use in all cases. However, significant cost differences between centralised and decentralised schemes can be observed in a simple economic analysis. Further research will examine the possibility for deriving model up-scaling algorithms to reduce computational requirements.CITATION:Keir, G and Woodley, A, 2013. Regional trade-offs between mine water and energy use - a water treatment case study, in Proceedings Water in Mining 2013 , pp 21-28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

Exploring long-term future possibilities for your business and methods for achieving them are critical functions of leadership. More than ever, strategic initiatives today have to be planned and delivered in an environment of disruptive change û driven by shifting business or regulatory imperatives, new technologies and global economic change, and diverse stakeholder interests. The notion of The Future as a single inevitable outcome is obsolete. There are many possible futures. This paper explains an innovative process û known as scenario planning û to help executives in the construction and testing of longer-term strategies to deal with uncertainty.

Jan 1, 2006

By P Salmon, M Kennedy

Sun Metals Corporation Pty Ltd (SMC), a wholly owned subsidiary of Korea Zinc Co Ltd (KZC) is a company formed to develop, construct and operate a zinc refinery, 11 km south of Townsville in North Queensland. The project opportunity exists because of on-going consumption growth for refined zinc metal, technological, environmental and economic obsolescence of existing zinc processing plants, and a prolonged ædroughtÆ of new zinc processing capacity under construction. The Project will utilise proven technology developed by KZC at the Onsan refinery in Korea. The Townsville Refinery has been designed to be the most environmentally-friendly zinc refinery in the world, and in particular to resolve the issue of secure, long term treatment of the ironbearing content of the zinc raw materials.

Jan 1, 1998

By Fletcher A. E W

Ever since it made its debut in 1962, in the form of a Robbins 31R, the raiseborer has become an accepted tool in the mining and civil construction industries. The first raiseborer to be used in the Witwatersrand goldfields made its appearance in 1968. This was a Robbins 42R which could raisebore 185m deep holes to 1,22m diameter. From 1968 to 1973 capability increased with the introduction of first the 61R, then the 71R and finally the 83R, which could raisebore 610m deep holes to 3,66m diameter. This created a demand for larger holes but the cost of bigger, more powerful machines requiring larger, stronger drill pipe, cutters and other accessories was prohibitive. To avoid replacing existing models such as the 71R, and in order to increase their capability, the concept of reaming in two stages sequentially was developed jointly by a German drilling equipment manufacturer, Wirth, their South African subsidiary, Transbor, and a local contractor, Rocbor Raiseboring and Mining Contractors. The result, the Sequential Reaming Head, proved most successful and existing machines, normally limited to 2,44m diameter holes, could now ream to 3,66m diameter. This created a demand for even larger holes. In order to maximise the use of the sequential reaming head to meet this demand the HG330, and subsequently the HG330SP raiseborer were developed. Using a 4,26m/6,02m cutting head, these machines have raisebored holes 1000m deep in hard rock. The raise- boring of the first major hole to be excavated by this combination, the 484m deep x 6,02m diameter surface shaft at Premier Mine is described. Reference is also made to six other shafts which have been completed or are under construction.

Jan 1, 1987

By G R. Hancock, M J. Saynor, J B. C Lowry, K G. Evans, M Narayan

Tools such as landform evolution models (LEMs) provide a means of predicting how a landform may evolve over extended periods of time. Here, we utilise the CAESAR-Lisflood LEM to assess a proposed rehabilitated landform of the Ranger Uranium Mine in the Northern Territory of Australia (Figure 1). The environmental requirements for the closure of the mine state that the final landform must be able to physically isolate tailings material from the environment for a period of at least 10,000 years (Australian Government, 1999). However, uncertainty exists as to the reliability of model predictions representing thousands of years.In this study, we use model predictions from an undisturbed pre-mine landform to calibrate the parameters used in model simulations of a post-mining rehabilitated landform over a simulated period of 1,000 years. Specifically, we vary environmental conditions such as rainfall, presence/absence of vegetation and surface particle size characteristics in a series of model simulations to determine their impact on the respective landforms, to revise model input parameters as required. A simulated period of 1,000 years was used as it represents a period in which long term landform evolution patterns and trends may be established and identified. CITATION:Lowry, J B C, Narayan, M, Evans, K G, Saynor, M J and Hancock, G R, 2018. Using an undisturbed landform to calibrate long-term predictions of the evolution of a rehabilitated landform, in Proceedings Life-of-Mine 2018, pp 133–137 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By B Abbasi

It is well known that most roof falls in coal mines typically occur at and around intersections. Room-and-pillar and longwall coal mining systems typically develop 3-way and 4-way intersections. This research develops an improved scientific understanding of stress distribution and associated instability behaviour around 3-way and 4-way coal mine intersections through 3-D numerical modelling and limited field observations. Numerical analyses were performed for an Illinois longwall coal mine to identify factors that influence intersection stability. The stability of immediate roof, floor strata, and coal ribs at and around intersections are considered with pre-mining regional horizontal stress. Non-linear failure analyses used the Hoek-Brown failure criterion for rock mass. Progressive failure zones in and around intersections were developed. For a typical 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of the immediate roof and floor layers. The mechanism of failure is similar for a 3-way intersection but the shape and extension of failed zones differ. For the 3-way intersection, the effect of off-set distance was analysed. It was found that minimum off-set distance of about 10 m (centre to centre distance between two 3-way intersections) was required to minimize interaction between two intersections. A simple instrumentation program monitor ground movements around intersections. These data were used to design the intersection geometry that is now being practiced by the mine. CITATION:Abbasi, B and Chugh, Y P, 2018. Instability analysis in three-way and four-way coal mine intersections, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 345–359 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Just as geophysics, in the form of 3D seismic and wireline logging, plays a key role in petroleum reservoir management, so too will geophysics play an important role in mining of coal, metals, and minerals in the 21 st century. The commercial and social imperatives driving greater use of geophysics are reduced costs, increased revenues, and enhanced safety. In short, superior utilisation of capital and management of risks. In relatively undeformed sedimentary environments it is possible to adapt petroleum-style 3D reflection seismic to image mines. This has been demonstrated most impressively in the Witwatersrand. Anglo-American, for example, completed a $1 million 3D seismic survey at Western Deeps in order to site a new $300 million shaft with confidence. Likewise, 3D seismic has gained rapid acceptance at Australian coal mines in recent years. Encouraged by these successes, metalliferous mining companies are supporting research in Canada and Australia, as well as South Africa, to adapt 3D seismic for more highly structured, metamorphic terranes. Because the mining industry is far more diverse than the petroleum industry in terms of commodities and geological environments, 3D seismic is not always cost-effective. A plethora of other geophysical techniques can be applied, many of which are employed in mineral exploration. Mine applications of geophysics differ from traditional exploration applications in two main ways: time scales and length scales are shorter, and boreholes are more plentiful. Borehole geophysical techniques therefore play a more significant role, both for logging and imaging. Logging systems detail the variations of in situ physical properties down the borehole at scales measured in centimetres, while geophysical imaging techniques can map features located tens or even hundreds of metres from the sensors. While geologists tend to think of boreholes in terms of chips and core, geophysicists perceive them first and foremost as access paths for instruments. Borehole logging has been employed at iron and coal mines for decades, mainly to accurately define ore boundaries in delineation holes. In base metal mines, Outokumpu implemented logging widely for orebody delineation in percussion holes in the 1980s. The benefit was a direct cost-saving, arising from substitution of core drilling with percussion drilling plus borehole logging. The practice has since spread to other companies. INCO, for example, defines nickel boundaries in blast holes at Sudbury using conductivity logs. The benefits are in the form of reduced dilution and enhanced ore recovery, flowing from a more accurate mine model. Density, natural gamma radiation, magnetic susceptibility, and conductivity are the principal metalliferous mine logging parameters because they can be recorded in both dry and water-filled holes. Sonic velocity is the premier geotechnical logging parameter, given its sensitivity to rock strength, stress, porosity, and degree of fracturing. Sonic is recorded routinely in exploration and geotechnical holes at coal mines. With the advent of slimline dipmeter, full waveform sonic, and optical and acoustic scanner tools, the role of borehole logging in geotechnical evaluations is expanding. Monitoring of strain and micro-seismic activity enhances safety during mine production. While qualitative interpretation of logs is adequate for stratigraphic identification or definition of boundaries, a wealth of quantitative information, eg density, can be derived from properly calibrated, repeatable geophysical logs. Moreover, geophysical logs can sometimes serve as surrogates for geochemical assays, and not only for magnetite and uranium. At OutokumpuÆs Kemi chromite mine, for example, gamma-gamma logging provides the basis for grade control. By reducing reliance on assaying, three benefits can be realised: reduced reliance on core drilling; lower core handling and assaying costs; and shorter turn-around times. Conventional downhole EM and borehole magnetics are used for near-mine exploration, and for ground sterilisation. Inco has enjoyed considerable success with borehole UTEM in the Sudbury Basin, for example, and Geopeko has applied three-component borehole magnetics successfully in the Tennant Creek area. Electrical techniques such as applied potential and magnetometric resistivity (MMR) are also finding application at mines. For higher resolution, borehole seismic, radio imaging, and radar have been invoked, with varying degrees of success, to delineate orebodies and map structures, or to geotechnically characterise the rock mass and identify hazards. Success mapping nickel sulphide shoots with borehole radar has been reported by WMC at Kambalda. There are no universal geophysical panaceas, and each mine imposes different geological, logistical, and economic constraints. Geophysics will not always be cost-effective. However, the greatest single impediment to expanded use of geophysics at mines has been the low level of awareness of geophysics on the part of most mine geologists, engineers, and managers and, equally, the limited understanding of mine geology and engineering exhibited by the majority of geophysicists. This myopia will be remembered as a 20th century affliction! Blue Sky areas for mine geophysics in the next ten years include integration of geophysical data acquisition with drilling, enhanced grade estimation and rock mass characterisation, and the incorporation of geophysical information into mine models using geostatistical techniques. All these advances will be predicated on an expansion of petrophysical knowledge.

Jan 1, 2000