Search Documents

By D Fergusson, J D. St George

Highwall stability is a major consideration in optimising opencast mine geometry. It involves assessing the risk of those slope failures that are large enough to have significant cost, safety and/or operational implications. These risks are then balanced against the value of the resource to arrive at an acceptable slope design. Load-deformation models (commonly referred to as ænumericalÆ models) of slopes provide a powerful tool in this decision-making process since they can be verified well before slope failure occurs. This gives the slope designer increased confidence in reviewing designs during excavation, potentially allowing early revision of pit geometry to either increase or decrease safety margins as appropriate. However, these models are not always adopted as they depend heavily on an appropriate choice of constitutive model and material parameters.   A preliminary load-deformation model of a 170m highwall in Solid Energy North (SEN) OperationsÆ Awaroa 4 opencast coal mine in the Rotowaro Coalfield has been prepared. This uses a strain-dependent constitutive model based on laboratory test results, strength parameters developed by SEN and excavation monitoring data. The laboratory testing has included triaxial compression tests on large-diameter fractured samples to characterise the stress-strain response of the closely-jointed soft rock masses that exist in many parts of the mine. Data from the monitoring of a 25m cut made during excavation of a haul road has been used to refine and verify the constitutive model. The resulting highwall model has predicted highwall crest movements corresponding to the excavation of each bench, for comparison with monitored values. Key model outputs are total horizontal movements of about 0.5m near the highwall crest and shear strains of 0.5-0.7% at the locations of potential bedding-parallel shear planes underlying the highwall. Most of the movement is expected to occur as creep rather than as an immediate response to excavation.

Jan 1, 2006

A variety of cement raw materials occur within the Cenozoic sequence in Northland. These form the basis of Golden Bay Cement's cement manufacturing operation at Portland, Whangarei. High grade limestone is taken from the Whangarei Limestone formation, which has been shown to have been sub-aerially weathered and developed mature karst features prior to deposition of the overlying allochthon sediments. In this instance, remobilisation of allochthon sediments following uplift and erosion is inferred. At Portland Quarry, argillaceous limestone is extracted from deformed thrust sheets in the allochthon sequence. Quarry operations have been designed to handle the steep asymmetric folds, thrust faults and fracture zones that affect the resource.

Jan 1, 1999

By B Murphy

Traditionally comminution optimisation has been focused on energy minimisation, whereas flotation optimisation has been focused on recovery improvement. One of the largest, if not the largest, operating cost over the life of a flotation circuit is electrical energy. With increasing pressure on operators to lower production costs and the cost of energy increasing, reducing the energy consumption of the flotation circuit can be beneficial to site economics. This paper reviews the use of energy by mechanically agitated flotation machines and discusses the measurement and benchmarking of energy consumption in modern flotation concentrators. Opportunities for improving flotation energy efficiency are also identified.CITATION:Murphy, B, 2013. Flotation energy consumption and opportunities for improvement, in Proceedings MetPlant 2013 , pp 399-412 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

The physical setting and background to mining operations on Misima Island and the overall plant lay-out are outlined. Developments and changes made to each section of the plant are described as they were encountered during commissioning and initial operation.

Jan 1, 1991

Determination of Porosity and its Influence on Specific Surface

Sep 13, 2010

By M R. Stevens

An approach of geological mapping and descriptive criteria has been used to identify hydrothermal eruption breccias, named the Onemana Breccia. These in part mantle a gold bearing fossil hydrothermal system located on the eastern side of the Coromandel Peninsula, New Zealand. Whilst eruption breccias are documented from active and recent geothermal centres within the Taupo Volcanic Zone and in Northland their recognition at Onemana is the first confirmed discovery for this lithotype within ancient hydrothermal systems of the Coromandel Volcanic Zone. At Onemana the widespread occurrence of silicification, sinters, volcanic lake sediments, eruption breccias and advanced argillic alteration allows classic hot spring epithermal modelling. The geological setting, distribution, lithological characteristics, hydrothermal alteration and trace element geochemistry of the Onemana eruption breccias are described. These breccias are closely comparable with hydrothermal eruption deposits elsewhere, particularly those in active ore forming hydrothermal systems. Consideration is given specifically to the role of the Onemana Breccia in an exploration strategy for discovering epithermal gold-silver deposits.

Jan 1, 1991

By J J. Culberson

The past 10 years has seen use of computers become widespread in the mining/exploration industry (including coal, precious and base metals, oil/gas and industrial minerals). This paper will concentrate on the use of computers as a tool to provide technical solutions (including data management, mine planning and operational support) to this industry rather than the use of computers to aid accounting, maintenance and inventory (æcommercialÆ) applications. This paper will review the processes and benefits of the use of computers in mining. We then review the use of technical computing locally here in New Zealand and see what business benefits local users have found from using computers in mining. We have, in research for this paper, spoken with mining software vendors from around the world to find out what is currently the æbest practiceÆ in the industry. The paper will then list what those vendors see as the ultimate improvement on the cards for the future of mining software.

Jan 1, 2000

By D Preedy, J K. Claflin, S R. La Brooy

A gold mine in north-eastern Africa has expanded throughput from 5 to 10 Mt/y in recent years. The original carbon regeneration kiln was incapable of achieving required throughput or meeting process conditions to reactivate the carbon due to heavy fouling by high molecular weight frothers and collectors. A new high temperature kiln was required.The design criteria for the carbon reactivation kiln and associated equipment were revised, then implemented in close cooperation with a kiln vender who had previously supplied kilns operating successfully on highly fouled carbon. The result is a whole facility, holistically designed to achieve the technical criteria.The new carbon reactivation facility has been operating since 1 July 2014. What have we learned? What has performed to expectations? What could be done better?This paper presents lessons learnt regarding the design, implementation, operation and maintenance of the Ausenco Carbon Reactivation Kiln. ‘Lessons’ are associated with threats and opportunities (risks) that have that have been realised. The importance of identifying and managing risks for even small straightforward projects is demonstrated.CITATION:Claflin, J K, La Brooy, S R and Preedy, D, 2015. Lessons learnt and performance – installing and commissioning an Ausenco carbon reactivation kiln in Africa, in Proceedings MetPlant 2015, pp 163–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Pressing-Drill Method - A Representative Method for Taking Analysis Samples from Recycled Materials

Sep 13, 2010

The Winton Basin is one of three Southland sub-basins. The oldest known sediments are Early Oligocene terrestrial shales, sands and lignites deposited in half grabens formed as a result of oblique extension. A marine transgression in the Oligocene deposited mid-outer shelf to upper bathyal mudstones. Shallowing of the basin and tectonic quiessence lead to limestone deposition in the Early Miocene. Regional tilting led to uplift in the north and east and deposition of terrestrial lignites and gravels across the basin and the basement high to the south.

Jan 1, 1992

As part or a programme to raise lead smelter capacity from 65.000 to 140.000 tons bullion per annum. one new 1000 sq. ft. updraught area sintering machine replaced eight small downdraught machines.The metallurgical specifications were based on and laboratory tests at Mount Isa. Existing practice filtering concentrate as part of the charge preparation system and discharging wet filter cake to mixing was retained. This dictated a hot return fines circuit to maintain the required feed moisture content at low return sinter ratios.The engineering specifications provided for cenlralized control of plant and process, minimum operating labour, high plant availabi;lity and highest standardsof hygeine. Crushing and conveying capacity was set to cater for the most optimistic level of sintering capacity.On start-up a number of major engineering and hygiene problems became apparent, in addition to normal teething troubles. These problems have largely been overcome and reliable operation. at less than optimum production rate is now being achieved.

Jan 1, 1968

Copper Extraction from Scrap Cables by Biotechnological Means

Sep 13, 2010

Australia's iron ore industry is entering a challenging period with the development of new orebodies, the introduction of new products and the push for further downstream processing. In addition, the recent price reductions for iron ore exports have intensified the focus on reducing capital and operating costs. To assist in these areas, CSIRO is expanding its research capabilities, including the incorporation into CSIRO of the Mineral Processing Laboratories in Perth, which were previously managed by the WA Department of Minerals and Energy. In addition, a large part of the $24.4 million expansion of CSIRO's Pinjarra Hills laboratories in Brisbane will be devoted to enhancing iron ore processing research, providing purpose built laboratories and large process bays.

Jan 1, 1999

A key driver to the success of a tunnelling project (the project) is the management of hydrogeological risk. The hydrogeological risk, if not managed, may cause significant impacts on the overall performance of the project. Impacts may include groundwater quality impairment due to contaminant transport and acid drainage from disturbed geology to groundwater, and groundwater lowering. The groundwater lowering and quality impairment may cause tunnel failure, with consequences such as injury to humans, as well as reduced property and environmental values, potentially costing millions of dollars to sponsors of the project. Depending on the nature of the contaminants and level of hydraulic connection of bedrock fracture along the length of tunnel, the contaminant transport may reduce structural strength of the tunnel due to corrosive action of contaminants such as acid drainage. The groundwater lowering can lead to varying degrees of ground settlement, posing threat of tunnel collapse. The management of hydrogeological risk includes:detection of potential pathways for contaminants into and around the tunnel,identification of factors responsible for the lowering of groundwater, and development of strategic measures to control groundwater lowering and contaminant transport. The paper presents an in-house hydrogeological risk management model named Vedanta-THRM (tunnel hydrogeological risk management). The model uses Risk Management Standard AS/NZS 4360:2004 (Standards Australia, 2004), Pressure State Response framework developed by Organisation of Economic Cooperation and Development, and Interaction Matrices. The Vedanta-THRM identifies important characteristics, processes and events of potential hydrogeological risk and develops control measures for managing hydrogeological risk throughout the life cycle of the project. The Vedanta-THRM was applied for a project in the early stages of planning and found to be useful in assessing, evaluating and reducing the hydrogeological risk in a managed approach that potentially increased the performance of the project. The application results also provided management options for use by project sponsors and insurance industry, which included tunnel risk financing options and options for equity investors to choose among various returns under different tunnel credit ratings.

Jan 1, 2008

By A Kurniawan, A Sjadat and M Akhasyah

PT Freeport Indonesia’s Deep Ore Zone (DOZ) is a block cave mining operation that has been in production for 15 years. DOZ is located approximately 900 m below surface and has an average production rate of more than 5000 t/d. The footprint of the extraction level will ultimately be 900 m long and average more than 200 m wide. The undercut level is located 20 m above the extraction level.While developing Panel 1K on the northern portion of the extraction level, a major geotechnical problem was encountered when there was a change in lithology and an associated fault intersection. A large collapse of the hanging wall of the extraction level drifts occurred in the area of the fault intersection between February and March 2011. This was followed by a collapse of one of the undercut level drifts directly above the extraction level in May 2011.It was suggested that the best approach to mitigate risk during rehabilitation was to systematically open up the failed area under the protection of a steel set support system. To achieve this, approximately 60 t of grout was injected from the undercut level to fill the voids created when the rock mass between the two levels failed. A ground penetrating radar system was used to survey the condition of the rock mass between the two levels before and after the injection of grout. After the grout injection phase was completed to a satisfactory level of confidence, rehabilitation activities started on the extraction level by taking out the now consolidated material from inside the drift in 2 m advances from under steel sets initially constructed in secured ground.Controlled blasting was the key aspect to the success of the initiative to open up just enough of the drift to systematically support the rock mass before the next set was installed. The systematic support consisted of in-cycle shotcrete sprayed over mesh pinned to the exposed rock, as effectively as possible, with splitsets before spiling the next advance’s protection canopy with rebar. Once secure, a combination of steel set and pumped concrete was installed as the final support. This final support provided a safe platform to repeat the process until the failed zone was safely traversed.CITATION:Kurniawan, A, Sjadat, A and Akhasyah, M, 2016. Rehabilitation of the collapsed panel 1K north in the Deep Ore Zone block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 763–768 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R Crookes

Mine to Mill optimisation is not a recently developed concept. It is one which is finally gaining greater acceptance in the Australian Mining Industry, possibly as a consequence of the downturn in markets and certainly made possible by the development of tools and techniques to measure and predict performance of mining equipment and milling plants. Fragment size after blasting has a major bearing on the performance of all aspects of mining and a major influence on the economics of the mine and mill. The process to optimise fragmentation consists of identifying the key factors, measuring their sensitivity through a modelling and trialing program and conducting economic evaluations on the changes on both the mine and mill. Management of the Ernest Henry copper-gold mine in NorthernQueensland, Australia, has espoused the Mine-to-Mill concept and isactively pursuing excellence in blasting to drive down the total cost of mining. Ernest Henry has extremely hard, wet and heavily jointed geological conditions, and had high powder factors and a large percentage of oversize material reporting to the crusher or ROMstockpile. A blasting improvement program was undertaken betweenErnest Henry Mining, Thiess Contractors and Orica Explosives tooptimise the ore size distribution, particularly the oversize component, as a step to reducing production costs. Measures of success included bringing the rock breaker back from double shifts to part-time operation and increasing direct dumping into the crusher from 70 per cent to 92 per cent. Tools and technologies to predict and measure the performance ofindividual blasts are needed before it is possible to optimisefragmentation or the downstream processes. These include suchspecialised Orica Explosives tools as SABREX, POWERSIEVE, andPOWERLINE and commercially available drill monitors. As importantare the more common still and video camera, borehole loggers,measuring tapes, surveying equipment such as face profilers, and ahigh-speed camera if possible. There are many tools which can be applied however it is rarely necessary or possible to use all of them due to time constraints and a point of diminishing returns. The critical point is knowing what the true parameters of the blast were compared to design - only then can the predictive tools be effectively utilised. Stage one of the program has seen gradual improvement as theunderstanding grew and practices have been implemented resulting inreduced bridging in the crusher, geological mapping with respective blast designs and the oversize component under control. This paper is about a process approach which links tools and technology to understand the fragmentation drivers and then to optimising the size distribution.The continuous improvement program continues...

Jan 1, 2000

Some design and feasibility studies have been made into possible methods of economic recovery of sulphur from smelter gases emitted at Western Mining Corporation's Nickel smelter at KalgoorIie in Western Australia. The smelter discharges some 330 000 tonne/yr of sulphur dioxide in a stream of approximately 6 per cent by volume of S02.Three possible recovery methods have been considered:1. The manufacture of sulphuric acid using the contact process.2. The concentration of sulphur dioxide to a pure form using dimethyl aniline as an absorbing medium.3. The reduction to elemental sulphur using natural gas as the reducing agent.Design studies were carried out by final year chemical engineering undergraduate students at Royal Melbourne Institute of Technology (RMIT) in 1981 under the supervision of the author and other teaching staff of the chemical engineering department. These studies indicate that sulphuric acid manufacture is the economically preferred recovery route.Markets for sulphuric acid include several potential mineral processing applications and the established fertiliser industry.Sulphuric acid is currently manufactured in a number of plants located at coastal regions of Western Australia using imported sulphur. The sulphuric acid is then used for superphosphate or titanium dioxide pigment manufacture at adjacent plants.The possibility is considered of manufacturing superphosphate at Kalgoorlie from locally produced acid obtained from the smelter gases and from phosphate rock railed to the site from the coast. The advantages of such a scheme include improved scale and technology of operation compared with some existing coastal operations, use of a waste material to replace imported sulphur, and avoidance of costs and hazards associated with railing large quantities of sulphuric acid.

Jan 1, 1983

The Greymouth Coal field is situated on the West Coast of New Zealand's South Island and has been mined for coal for more than 120 years. The area covered in this paper is within the Rapahoe Sector of this field and contains >200 million tonnes of low ash, low sulphur, bituminous rank coal. Paper No 6, presented to the 19th Annual Conference of the New Zealand Branch of The Australasian Institute of Mining and Metallurgy in Christchurch in August 1985 by R G Bowman, explained 'A Geologist's View' of the 'Economic Potential of the Greymouth Coalfield', and describes previous geological assessments of the Rapahoe Sector.

Jan 1, 1989

OneSteel and BlueScope Steel have been working with the CSIRO to develop sustainable carbon fuels and reductants which are suitable for use in the iron and steel industry. One of the initial focuses of this work has been a process called steel recarburisation which is the addition of carbon to liquid steel to produce particular steel grades. This paper reports on the preliminary work and the recent full scale recarburisation plant trials conducted at the OneSteel Sydney Steel Mill.   Preliminary experimental work involved kilogram scale recarburisation of liquid steel with a range of commercial and prepared charcoal products. This work showed that charcoal dissolves into liquid steel very quickly and that carbon recovery to steel was inversely related to the charcoal volatile content. Initial larger scale work focused on the collection of wood, and preparation of low volatile charcoal which is required for steel recarburisation. Approximately three tonnes of charcoal was prepared at the Corrimal coke ovens of the Illawarra Coke Company. This charcoal was dried, crushed, sized and packaged in a form suitable for addition to 80 tonne liquid steel ladles.   The recarburisation trial was conducted over 30 ladle heats during June 2009. The charcoal was manually added to the liquid steel in 5 kg bags using normal plant practice. Conventional commercial recarburiser was also added to the liquid steel in alternate ladle heats. The performance of the charcoal was compared with the conventional recarburiser based on the carbon recovery to steel, hydrogen pick-up by steel and the rate of carbon dissolution into steel.   An analysis of the trial results showed that the charcoal performed at least as well as commercial recarburiser in carbon recovery and rate of dissolution but may have resulted in a slightly higher hydrogen content of steel. This is probably due to the higher moisture content of charcoal. The main challenges in the future include: increasing the charcoal density to improve transport and handling economics, securing a sustainable supply of biomass for the steel industry and developing a charcoal production industry so materials of suitable quality for both production and trials on other applications can be conducted.

Jun 1, 2010

By C E. J de Ronde

Most of the world's economically significant volcanogenic massive sulphide (VSM) deposits are considered to have formed in submarine arc and backarc settings. While the Kermadec-Tonga arc is an excellent example of an intra-oceanic arc setting, it remains largely unexplored in terms of submarine mineral resources. More than half of this arc (~1400 km of the >2500-km-long feature) lies within the EEZ of New Zealand, where it is defined by at least one sub-aerial and 33 submarine volcanoes. The NZAPLUME (New Zealand American PLUme Mapping Expedition) cruise of March 1999 provided a systematic assessment ofhydrothermal activity on the southernmost 13 submarine volcanoes along the southern Kermadec arc. Using prospecting techniques based on the physical and chemical detection of hydrothermal plumes, we discovered that more than half (7 of 13) of the southern Kermadec volcanoes host one or more active hydrothermal systems at depths ranging between <200 to 1800 m. Chemical results show that the fluids discharged are compositionally diverse among volcanoes and between sites at a single volcano. Plumes over more than half of the volcanoes are gas-rich (He, CO2, H2S) relative to mid-ocean-ridge (MOR) plumes. In addition, most sites are highly enriched in Fe, yielding Fe/Mn values that far exceed those for MORs. One interpretation consistent with these observations is compositional overprinting by addition of magmatic fluids, which are typically highly enriched in gaseous and ionic components. Regardless of the source, it is clear that the ligands (HS-, Cl-) required to efficiently transport base (e.g. Cu, Zn, Pb) and precious (e.g. Au, Ag) metals to the seafloor are abundant in Kermadec arc fluids. We conclude that modem analogs of VMS deposits are likely forming at multiple sites along the Kermadec arc and within the EEZ of New Zealand.

Jan 1, 2000