Search Documents

By Michael Tenenbaum, T. L. Joseph

Recent researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any substantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed. In some recent work, Diepschlagl found that, all other factors remaining constant, the degree of reduction of iron ores was much greater when carried out under pressure. Pressures as high as seven atmospheres were used. The degree of reduction was determined from the ferrous and ferric iron in the sponge iron. Results were obtained using both carbon monoxide and hydrogen at temperatures of 400°, 600° and

Jan 1, 1939

A. L. FIELD, Cleveland, Ohio (written discussion*.-)In equation 2, B is used to denote the ratio of bases (lime plus magnesia ) to acids (alumina plus silica) it being stated that this ratio gives more concordant results than the ratio either of bases to silica, or of lime to silica. I find, however, that, by making use of the ratio between true CaO (CaO by analysis minus sulfur calculated to CaS) to acids, equation 2 may he modified to agree with the observed facts within an average error of 0.0041 per cent. sulfur instead of 0.0045 per cent. The revised equation is s = 0.072 + 0.01835 - 0.00061 (t - 1400) - 0.0403B where B is the ratio of true CaO to Al2O3 Plus Si02, and the other symbols have the same significance as before. I would not appear to stress too much this slightly better agreement of the revised equation with the observed sulfur. Yet I believe that the use of this ratio of true CaO to acids is to be preferred, if for no other reason than the fact that it is more in harmony with the previous findings of the Bureau of Mines with regard to the effect of magnesia and other impurities on slag viscosity.1

Jan 12, 1919

By P. L. Menaul, P. P. Spafford

This paper discusses the most dangerous form of corrosion encountered in condensate-well oil production, the discovery of the agent causing this corrosion and the remedial chemical treatment proved effective by field use. The injection of ammonium hydroxide, even as little as one quart per day, has proved effective in preventing gas-condensate well corrosion. The injection of "Bone oil" is applied to wells producing brines containing calcium and magnesium salts. Introduction The severe corrosion of equipment in high pressure gas condensate wells has been a problem for several years and numerous papers have been presented on the subject. The term "gas condensate" or "distillate well" is applied to a distinct variety of hydrocarbon producing well, the characteristics of these wells being high bottom-hole (formation) pressures and temperatures and high gas production. These wells usually produce about 40 gal of water per million cubic feet of gas and the gas contains from 0.1 pct to 2 pct carbon dioxide. In the operation of this type of well, the operators soon noted severe internal corrosion of the pipe carrying the production. In some instances the dl tubing has been found to be corroded to perforation in eight months. The high well head pressures of 2500 to 8000 psi makes any weakening of the well equipment by corrosion extremely hazardous. Bursting of the well equipment results in very expensive repair operations and may result in the loss of valuable production, loss of the costly well, or even loss of life. In November 1944, a gas-condensate well in a Gulf Coast field producing from 9500 ft showed a tubing leak. The well was "killed" by filling it with mud through the tubing, and then the tubing was pulled. Corrosion was found to have caused several perforations in the tubing, Fig I. While the mud was being circulated to kill the well, a high pressure jet from the corroded hole in the tubing perforated the casing and damaged the well to the extent that the cost of repairs amounted to $75,000. In November 1944, another gas-con-densate well in a Gulf Coast field producing from 11,400 ft showed tubing failure. This well had been producing an average of 2,500,000 cu ft of gas daily for two years. In the workover of this well, it was found that a hole one inch in diameter had corroded through the tubing and that corrosion had reduced the wall of the tubing to less than half the standard thickness over large areas of the interior of the tubing. It was found that corrosion had also caused two leaks in the casing. After four months spent in an attempted workover failed to make the well safe for further production, the well was plugged and abandoned at a total loss of $300,000,00.

Jan 1, 1948

By P. L. Menaul, P. P. Spafford

This paper discusses the most dangerous form of corrosion encountered in condensate-well oil production, the discovery of the agent causing this corrosion and the remedial chemical treatment proved effective by field use. The injection of ammonium hydroxide, even as little as one quart per day, has proved effective in preventing gas-condensate well corrosion. The injection of "Bone oil" is applied to wells producing brines containing calcium and magnesium salts. Introduction The severe corrosion of equipment in high pressure gas condensate wells has been a problem for several years and numerous papers have been presented on the subject. The term "gas condensate" or "distillate well" is applied to a distinct variety of hydrocarbon producing well, the characteristics of these wells being high bottom-hole (formation) pressures and temperatures and high gas production. These wells usually produce about 40 gal of water per million cubic feet of gas and the gas contains from 0.1 pct to 2 pct carbon dioxide. In the operation of this type of well, the operators soon noted severe internal corrosion of the pipe carrying the production. In some instances the dl tubing has been found to be corroded to perforation in eight months. The high well head pressures of 2500 to 8000 psi makes any weakening of the well equipment by corrosion extremely hazardous. Bursting of the well equipment results in very expensive repair operations and may result in the loss of valuable production, loss of the costly well, or even loss of life. In November 1944, a gas-condensate well in a Gulf Coast field producing from 9500 ft showed a tubing leak. The well was "killed" by filling it with mud through the tubing, and then the tubing was pulled. Corrosion was found to have caused several perforations in the tubing, Fig I. While the mud was being circulated to kill the well, a high pressure jet from the corroded hole in the tubing perforated the casing and damaged the well to the extent that the cost of repairs amounted to $75,000. In November 1944, another gas-con-densate well in a Gulf Coast field producing from 11,400 ft showed tubing failure. This well had been producing an average of 2,500,000 cu ft of gas daily for two years. In the workover of this well, it was found that a hole one inch in diameter had corroded through the tubing and that corrosion had reduced the wall of the tubing to less than half the standard thickness over large areas of the interior of the tubing. It was found that corrosion had also caused two leaks in the casing. After four months spent in an attempted workover failed to make the well safe for further production, the well was plugged and abandoned at a total loss of $300,000,00.

Jan 1, 1948

By Welton J. Crook

Unless present, in considerable praportion, metals of the precious-metal group—other than gold and silver—are not readily detected by the methods of fire assaying usually applied to ores and metallurgical products. Platinum, when present in small quantity, will ordinarily be reported as silver unless special methods of parting are used. Other elements occurring in the gold itself are all fluxed and slagged in the assay operation and if analyses are made on bullions the melting and slagging operations to which the bullion has been subjected may eliminate most of the associated elements. On the other hand, the analysis of precipitate from the cyanide treatment of gold ores may reveal the presence of many unexpected elements, such as tungsten and molybdenum. It is uncertain, however, whether many of the elements present in the precipitate are derived from the ore gangue or from the gold itself. No very general survey of the distribution of metallic elements in gold seems to have been made. Rose and Newman,l in connection with the composition of native gold, say in part as follows: Gold is occasionally found alloyed with copper and sometimes also with iron, bismuth, lead, mercury, tin, antimony, palladium or rhodium. Rhodium gold from Mexico was found to be of the specific gravity 15.5 to 16.8 and contained 34 to 43 per cent of rhodium. The native alloy of palladium, gold, and silver from Porpez contains 85.98 per cent of gold, 9.85 per cent palladium and 4.17 per cent silver. Mal-donitk, from Victoria, contains gold 64.5 per cent, bismuth 35.5 per cent (Louis). Dana2 says that native gold is usually alloyed with silver in varying amounts, and that sometimes it also contains traces of copper and iron. Rare varieties contain palladium, rhodium and bismuth. Other authors, for instance Zeigler3 and Clark,4 give similar information. Most references on the subject agree that ordinary native golds contain, in common, the elements silver, copper and iron. After completion of the work of which this paper is a record, the conclusion is reached that all ordinary native gold probably does contain these elements and, although in certain cases other elements may be found to be present, that it is difficult to

Jan 1, 1943

By Welton J. Crook

Unless present, in considerable praportion, metals of the precious-metal group—other than gold and silver—are not readily detected by the methods of fire assaying usually applied to ores and metallurgical products. Platinum, when present in small quantity, will ordinarily be reported as silver unless special methods of parting are used. Other elements occurring in the gold itself are all fluxed and slagged in the assay operation and if analyses are made on bullions the melting and slagging operations to which the bullion has been subjected may eliminate most of the associated elements. On the other hand, the analysis of precipitate from the cyanide treatment of gold ores may reveal the presence of many unexpected elements, such as tungsten and molybdenum. It is uncertain, however, whether many of the elements present in the precipitate are derived from the ore gangue or from the gold itself. No very general survey of the distribution of metallic elements in gold seems to have been made. Rose and Newman,l in connection with the composition of native gold, say in part as follows: Gold is occasionally found alloyed with copper and sometimes also with iron, bismuth, lead, mercury, tin, antimony, palladium or rhodium. Rhodium gold from Mexico was found to be of the specific gravity 15.5 to 16.8 and contained 34 to 43 per cent of rhodium. The native alloy of palladium, gold, and silver from Porpez contains 85.98 per cent of gold, 9.85 per cent palladium and 4.17 per cent silver. Mal-donitk, from Victoria, contains gold 64.5 per cent, bismuth 35.5 per cent (Louis). Dana2 says that native gold is usually alloyed with silver in varying amounts, and that sometimes it also contains traces of copper and iron. Rare varieties contain palladium, rhodium and bismuth. Other authors, for instance Zeigler3 and Clark,4 give similar information. Most references on the subject agree that ordinary native golds contain, in common, the elements silver, copper and iron. After completion of the work of which this paper is a record, the conclusion is reached that all ordinary native gold probably does contain these elements and, although in certain cases other elements may be found to be present, that it is difficult to

Jan 1, 1943

By Daryl R. Tweeton, Jerry R. Riding, Grant Buma, Frank J. Rosswog

In situ solution mining of uranium has environmental advantages over conventional mining. The leaching of uranium, however, alters the ground-water quality in the aquifer where the mining occurs. Currently, regulations require that the ground water be restored to approximately its original condition. This paper, a summary of a study funded by the Bureau of Mines, reviews the state of the art in restoring ground-water quality after in situ uranium leaching. Current restoration practices discussed include disposal of liquid wastes in deep disposal wells and evaporation ponds, producing from all wells during restoration, and recirculating water purified in surface plants. Methods for predicting the effectiveness and cost of current techniques are presented. Possible alternative techniques are also described. Two restoration operations are discussed.

Jan 1, 1979

By D. E. Menzie, D. L. Dauben

This paper discusses the physical parameters involved in the slow flow of high molecular weight polymer solutions in porous media. The interacting effects of polymer properties and porous media properties on flow performance are considered. Experiments were conducted with the polyethylene oxides, with molecular weights ranging from 200,000 to over 5,000,000. Frontal advance velocities ranged from I to 30 ft/day. The porous matrix consisted of a flow cell packed with glass beads. Polymer solutions were characterized by viscosity and normal stress measurements. Under certain conditions, unexpectedly high flow resistance was observed. This behavior was observed to be a function of flow rate, pore size, polymer molecular weight and concentration. The polymer solutions exhibit "dilatant" flow behavior in porour media in contrast with the pseudo-plastic behavior in simple flow systems. A theoretical ex-planation of such behavior is presented. INTRODUCTION The use of polymers in the injected water of a waterflood increases oil displacement efficiency by reducing the mobility (k,/pu) of the driving phase. A reduced driving phase mobility results in improvements in the areal sweep efficiency and in the vertical coverage in stratified reservoirs. This mobility reduction may be achieved by a permeability reduction, a viscosity increase or by a combination of the two. Early attempts at increasing the injected water viscosity were not successful because of the poor economics involved. The use of such materials as glycerin, sugar or glycols to increase water viscosity was not economically feasible. Attempts in using certain naturally occurring polymers were not too successful because of the high polymer losses to the rock. A high molecular weight, partially hydrolyzed polyacry-lamide was introduced 3 years ago as a waterflood additive.',' Initial work by Pye' indicated that the presence of these polymers in dilute concentrations decreases the water mobility 5 to 20 times more than would be expected from measurements of the solution viscosity. Such an effect would be of obvious economic value since only a small polymer concentration would be required to accomplish a large reduction in water mobility. This research was designed to study the basic flow mech anisms of polymer solutions in porous media. The interacting effects of polymer properties and porous media properties on flow performance are considered. This study indicates some of the conditions under which these interactions can lead to significant mobility effects. is valid only for Newtonian fluids. For polymer solutions and other non-Newtonian fluids the equation must be modified to consider that viscosity is a variable quantity. Modification of the Darcy equation to include non-Newtonian effects has been the subject of several recent investigations."" The modifications generally adopt a rheological model. such as an Ellis or Dower law model. to Dorous media by defining some characteristic channel radius. Most of these studies showed the porous media flow behavior to be predictable from viscometric data. Investigations involving the flow of high molecular weight polyacrylamide solutions through cores have generally encountered the high flow resistances reported previously by Pye. This high flow resistance has generally been attributed to an in-depth permeability reduction, as evidenced by a reduced permeability to water which has displaced polymer solution from the porous media. Marshall and Metzner" report high flow resistances, which they attribute to viscoelastic effects. In this paper, the effects of polymer molecular weight, pore size, flow rate and concentration are considered. The polymers used are the polyethylene oxides known as Poly-ox. This class of polymers was used because of its availability in a wide range of molecular weights and because of its known ability to propagate well through porous media. THEORY PHYSICAL PROPERTIES OF POLYMER SOLUTIONS The polymer molecule dissolves in water by means of hydrogen bonding, but retains some of its own structural identity while in solution. Nonionic polymers, such as polyethylene oxide, are generally considered to have a random coiling configration. This type of molecule has the ability to "sequester" or hold a large volume of solvent within its coils in a manner similar to that of a sponge. The random coil is easily deformed and under an applied stress

By E. H. Roberts, L. G. Swenson, F. C. Nix, R. A. Morgen

THE binary system lead-antimony has been the subject of comprehensive investigations in these laboratories by Dean' and his associates. The effect of a third constituent on this system, particularly on the lead-rich alloys in which dispersion hardening was found, has a commercial value as well as an academic interest. This paper covers the effect of the addition of copper, bismuth and tin, all of which are likely to be found in commercial lead-antimony alloys, and is divided into three parts, as follows: I. The System Lead-Antimony-Copper II. The System Lead-Antimony-Bismuth III. The Lead Corner of the System Lead-Antimony-Tin These three systems are of three different types, and hence may be considered as covering three general kinds of additions. Bismuth forms no compounds with either lead or antimony and forms solid solutions with both. Copper forms several compounds with antimony as well as solid solutions but with lead it forms a two liquid layer system and no appreciable solid solution. Tin is soluble in both lead and antimony in the solid state and also forms a compound with antimony. The effect of small amounts of bismuth on the lead-antimony alloys is small, having no appreciable effect on the solubility of antimony. The temperature of the solidus floor is lowered appreciably by the presence of bismuth, cutting down the range of heat treatment. Copper, on the other hand, due to compound formation, increases the apparent solubility of antimony. The excess antimony is tied up with the copper finally and so is not available for dispersion hardening. The net result of addition of small amounts of copper is to shift the dispersion hardening peak of the

Jan 1, 1928

By A. B. Cox, L. W. Wark

An attempt has been made to compare the influences of the two most widely used depressants—alkalis and sodium cyanide—and the most widely used activator—copper sulfate—on the air-mineral contact induced by five sulfur-bearing compounds: (1) sodium di-ethyl dithio-phosphate (sodium Aerofloat); (2) potassium ethyl xanthate; (3) sodium di-ethyl dithiocarbamate; (4) potassium iso-amyl xanthate; (5) potassium di-n-amyl dithiocarbamate. Three different organic types are included in lhis group and for two of these types a higher and a lower homologue have been tested. The study of potassium ethyl xanthate, the preliminary results of which have been described,' was continued until there had been obtained a comprehensive account of the influence of variations in pH value and in the concentrations of xanthate, sodium cyanide and copper sulfate on the adsorption of this xanthate by galena, sphalerite, pyrite and chalcopyrite. With concentrations of copper sulfate and collector that the work with ethyl xanthate indicated would give the most illuminating. results, the other four collectors were tested, in a less exhaustive way. The same general principles determine the influence of alkalis, cyanide and copper sulfate, no matter to which type the collector belongs, but there is a gradation in the quantitative measure of such influence. In the list above, the five collectors are cited in the order of their capacity to withstand the depressants, sodium Aerofloat being the least resistant, potassium di-n-amyl dithiocarbamate the most resistant. This order coincides substantially with that of the solubilities of the heavy metal salts formed by double decomposition with the collectors, those formed from sodium Aerofloat being most soluble. There is little difference between the third and fourth members of the series, and under certain conditions their positions are reversed. In general, then, of the three types of collectors investigated, the dithiophosphate type is most easily influenced by depressants, and the

Jan 1, 1935

By Richard D. Call

Predicting the performance of a waste embankment requires an estimate of the properties of the waste and foundation materials. The performance characteristics and the associated material properties are: [ ] Methods for obtaining estimates of the material properties include: laboratory and field testing, back analysis, and indirect estimates from other material properties. The most critical technical need is the development of indirect methods for use in feasibility studies and mine planning, prior to production when actual samples of waste material are not available. Material properties are not unique, single values; they are probability distributions. There are two components to these distributions: the uncertainties in testing and the inherent variability of the material. The objectives of a material properties evaluation should be to obtain an unbiased estimate of the property distributions rather than the average or the minimum value. Whether the current trend to a probability design analysis is followed or a simple sensitivity analysis is conducted, the unbiased probability distribution is preferable to single values.

Jan 1, 1985

By Clark B. Risler, Walter E. Thomas

MILL planning must include electrical drives and a system to supply them. These should be considered at the time metallurgical and mechanical plans are being made. Because it is convenient, flexible, reliable, and economical, electricity is the accepted source for powering mill concentrating equipment. Ore-treating mills have grown to the point where a single mill has been built using 360 motors ranging from 1 to 1000 hp and totaling 50,000 hp. Such a system of electrical drives can be scattered over a square mile and employ 4000 to 220 v. Drive Motor Characteristics: Since ore processing is predominantly a continuous operation, very few of its drives require wide speed variation after initial adjustment. Consequently squirrel cage, wound rotor, and synchronous alternating current motors are most often used.

Jan 5, 1957

By Milton E. Wadsworth, John N. Ong, W. Martin Fassell

The temperature and oxygen concentration dependence on the reaction of sphalerite in oxygen at pressures from 6 to 640 mm Hg have been investigated in the temperature range 700° to 870°C. Sphalerite has been found to oxidize linearly over this entire temperature and pressure range. At higher rates, considerable self-heating was observed. The dependence of the oxidation rate on the oxygen concentration may be expressed by: Rate = k' where k' is the specific rate constant and 0 = K1[O2]/(1 + KI[O2]), where K1 is the equilibrium rate constant for the adsorption of oxygen on sphalerite. Values of the activation energy and the enthalpy of adsorption were found to be 60.3 and —59.6 kcal per mol, respectively. Data have been presented that indicate conditions under which either a sulphatizing or an oxidizing roast may be obtained. ROASTING processes have been employed in the metallurgy of a great number of basic metals in use today. Until recently, however, little attempt has been made to deduce the fundamental mechanism by which oxidation takes place. Structural changes upon oxidation have been investigated1 = and thorough work has been performed with regard to the reaction products and the thermodynamics of the oxidation reactions. The objective of this investigation was to determine the rate of oxidation of sphalerite and to apply the absolute reaction rate theory in the theoretilcal interpretation of the experimental results." "O Description of Apparatus The apparatus contains the following features: 1—a furnace with gas system, 2—an autographic weighing system, and 3—a temperature control system. Furnace With Gas System—The furnace was mounted by a yoke on each end and was free to travel up and down on steel guide rods, permitting the introduction and removal of samples from the apparatus with minimum difficulty. The furnace was heated by three sections of Kanthal wire wound externally on a zirconia tube and insulated with Fiber-frax. Pure gases or mixtures of gases were introduced into the lower end of the furnace through two flowmeters, a mixing chamber, and a gas-tight sparger, Fig. 1. The gaseous products of the reaction and the unused gases were prevented from escaping to the atmosphere by maintaining a small negative pressure on the system. This procedure permitted air from the outside to enter through the small an-nulus around the quartz suspension fiber and prevented the escape of the internal gases. Autographic Weighing System—The autographic weighing system consisted of an adapted gold balance, a photoelectric circuit, and a weight recorder, Fig. 2. The sample was suspended from one end of the balance beam by means of a platinum chain outside the furnace and a long thin quartz fiber on the inside of the furnace. On the other end of the balance beam, the necessary weights were added to counterbalance the sample. In addition, a calibrated chain was added to the balance which was linked directly to the weight recording unit. Control was effected by means of a photoelectric circuit." A parallel beam of light from a strong source was directed onto a small front-surfaced aluminum mirror mounted in the middle of the balance beam and then to a front-surfaced mirror mounted on the ceiling of the room. The beam was then reflected onto a front-surfaced right prism at a distance of 9 ft from the balance

Jan 1, 1957

By J. A. Jr. Church

I. EARLY FURNACES. COPPER blast-furnace construction in America has long recognized a general standard in the rectangular mater jacketed shaft with separate forehearth. The details, however, and especially those relating to shaft dimensions, have had to meet a great variety of conditions, and show no uniformity whatever. Selecting a few of the present day Western plants, we find furnace lengths varying from 12.5 to 87 ft., widths at tuyere level from 42 to 84 in., and heights above tuyeres from 5 ft. 4 in. to 22 ft. 4 in. ; and comparing present designs with those of the past, we meet contrasts no less striking. Unlike its transverse section, the length of a furnace has come to depend rather on the size of unit desired than on the requirements of smelting ; and if the question of length be ignored, several of the various existing designs can be grouped together on the basis of a common transverse section. This section, having a width at tuyere level of 56 in. and a height above tuyeres of 18 ft., was developed at Great Falls, and the story of its development contains some interesting features. Ground was broken for the Great Falls works in the spring of 1891. About a year later, the concentrator was able to begin operation, followed within the next few mouths by the Brueckner, reverberatory, and converter departments, and in April, 1893, by the first blast fur-

Jan 7, 1913

By E. S. Leaver

THE presence of soluble base metals in precious-metal ores usually precludes cyanidation as the best method of treatment. The laboratory experiments described in this paper show the possibility of cyanidation of gold-silver ores containing less than 0.5 per cent, of cyanide-soluble copper and the effect of zinc in the cyanide solution. PART I.-COPPER IN CYANIDATION The proposed process of cyanidation of precious-metal ores containing copper is based on the regeneration of about 80 per cent., of the cyanide used in the dissolution of the copper. The method of regeneration involves a combination of the sulfide and the acid precipitation of the copper and silver. The resultant solution is made alkaline with lime, and the gold is precipitated with zinc dust. Solubility of Copper Minerals in Cyanide Solution In order to determine the solubility of copper minerals, including metallic copper, under the usual conditions for cyanidation, experiments were conducted with synthetic ores. Each ore sample was prepared by mixing the particular pure copper mineral with barren sea sand. Both the mineral and sand were ground to pass 100 mesh before they were thoroughly mixed. The percentage of copper in each head sample was determined by direct assay, excepting the metallic copper sample, which was computed on weights before mixing. Table 1 gives the results.

Jan 1, 1929

By Clarence Zener

IT is customary to regard the stress-strain relation as consisting of two parts, the elastic region and the plastic region. The essential attribute of the plastic region is the presence of a permanent set, which remains upon removal of all stresses. The essential attribute of the elastic region is the absence of such a permanent set. Absence of a permanent set does not imply a linear relation between stress and strain, nor even a single valued relation. In fact, in no real metal is stress a single valued function of strain in the elastic region. The property of a solid in virtue of which stress and strain are not uniquely related in the elastic range will be called "anelasticity." The purpose of the present article is to review and correlate the past work upon the anelasticity of metals. The following paper by W. A. West124 describes investigations upon anelastic properties of iron. Many manifestations of anelasticity have been observed, the first as early as 1835 by Weber.1,2 In his experiments Weber subjected a specimen to a constant load (or deformation) for a given time, and then suddenly removed the load. He observed that most of the deformation suddenly disappeared, but that there remained a residual deformation, which disappeared only gradually with time, as is illustrated in Fig. I. The occurrence of a residual deformation which only gradually disappeared, Weber called the elastic after-effect (Elastische Nackwirkung). An extensive review of the early work upon elastic after-effects has been given by Auerbach.3 Another manifestation of anelasticity is the dependence of the elastic constants-e.g., Young's modulus upon the method of measurement. Thus, if dynamic methods are used, the measured value will depend upon the frequency of oscillation. Still another manifestation is dissipation of energy attending vibration, called damping or internal friction. One objective of metallurgical science is the understanding of the plastic and fracture properties of metals in terms of their microstructure. Through such an understanding will come the ability to design microstructure to give the desired mechanical properties. A study of an elasticity will furnish an invaluable aid in the attainment of this objective. Such studies, when properly guided, yield information regarding the relation between stress and strain in the individual components of the microstructure. In order, however, that this type of information may be obtained, it is necessary that the experimental studies of anelasticity be interpreted by the appropriate mathematical analysis. This article, therefore, starts with the mathematical formulation of anelasticity.

Jan 1, 1946

By J. Van Steveninck, A. C. Pols, R. Feenstra

In the course of time, an increasing number of investigations on jet cutting all kinds of material, such as rock,1,2,3 metal,4,5 and wood6 have been reported to serve various applications. A number of papers have been published on these subject, 7,8,9 some of which refer to jets purposely containing abrasives, termed 'jetted particle drilling'.7 Since such abrasives complicate fluid handling considerably and do not appear to be absolutely necessary for making holes, only conventional drilling fluids have been considered. A large part of our investigation has been performed with the aid of three laboratory-type drilling machines, which permit tests on both micro-bits (1 ½ in. ) and full-scale bits (6 ½ -9 5/8 in. ) . In view of the application of jets in deep holes, care has been taken to simulate hydrostatic pressures as they exist in the field on the hole bottom. These have been found to have a major effect on the bit-penetration rate for various drilling fluids.

Jan 6, 1974

By Prakash C. Kapur

Many balling and gradation system6 generate self- similar size distributions of the agglomerates. Inspection of the experimental data shows that this is also true of the steady state distributions resulting from the granulation of coarse, partially wet powders, for example, the fertilizer feeds. This result is exploited in the derivations of a number of simple and useful relationships that are pertinent to the analysis of these agglomeration systems. The bonding liquid demand of the granulating charge is a third order polynomial function of the dimensionless ratio of feed particle size to median granule diameter in the weight-fraction distribution. The median size, in turn, is the scale factor or characteristic size parameter in the similarity distribution. The granule size distribution, therefore, is completely specified by the liquid content and the similarity function, and so are the process efficiency and the ungranulated component In the product at steady state.

Jan 1, 1977

By Howard Willey

Mining operations of the Charcas unit at present are limited to the Tiro General mine at Charcas, in the State of san Luis Potosi, Mexico. The Tiro General mine was first operated during the Spanish occupation of Mexico for rich silver ores in an oxidized zone along the outcrop of the principal vein. In depth the ore is a complex sulfide with widely varying proportions of sphalerite, argentiferous galena and chalcopyrite ; and until recent years, it was economically impossible to carry on mining otherwise than irregularly in sections of the veins richest in galena and chalcopyrite. The advent of selective flotation brought the orebody as a whole within the field of economic interest, and a flotation mill of 650 metric tons daily capacity was constructed in the year 1925. The mining of partly worked-out sections of the mine, as well as the very heavy ground in most of the stopes opened in virgin ore, presented an unusually difficult problem. This paper describes the so-called "filled top slice" stoping method finally adopted as the standard system. Physical and Geological Conditions The principal orebody of the mine is an oreshoot about 1400 ft ng in a fissure vein striking about east and west and with an average lip of 70" to the north. The footwall of the orebody is fairly cleancu and regular both longitudinally and vertically and generally shows a dell-marked post-mineral slip. The footwall rock varies from a fairly strong limestone to a broken, metamorphosed limestone which requires heavy timbering. In some sections it is an altered, crumbly porphyry, which swells badly and necessitates frequent renewal of drift and raise tirnber. The hanging wall is irregular and frequently an assay wall. The stopina width ranges from a few feet up to more than 90 ft.; it averages about 30 ft. For the most part the hanging-wall rock is a shattered and altered monzonite porphyry, nearly aways requiring heavy timbering. The orebody is greatly fractured by post-mineral movement, which usually followed the footwall and left it as a smooth surface frequently covered with a slippery clay gouge. Two well marked transverse faults

Jan 1, 1931

By M. E. Wadsworth, R. D. Groves, B. W. Madsen

Experimental results obtained from large-scale (7 ton), long-term (500 days) leaching of low-tenor copper sulfide ores were interpreted by a geometric model involving the movement of a reaction zone through the ore fragments. The postulated leaching mechanism involved mixed kinetics and included diffusion of the reacting species through the host rock and a chemical reaction at the surface of the mineral particles. Ore properties which were considered were Ore particle size and shape, grade of ore, and mineral content. Excellent agreement between the mixed kinetic model and the laboratory leaching results was obtained when -1/2-in. ore particles were not included in the leach. Also, a satisfactory prediction of copper recovery from +1/2-in. ore with a different particle size distribution was made; however, it was necessary to modify the shape factor in the model. Prediction of copper recovery from an ore sample which included the -1/2-in. fine fraction and leaching for 460 days was 56.5%, and the recovery from leaching was 47.0%. The presence of fines caused solution channeling and a deficiency of oxygen which inhibited the leaching rate. Also, compaction of fines around coarser particles interfered with circulation around the ore particles, and bulk solution transport probably was a rate controlling factor.

Jan 1, 1976