Search Documents

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985

By O. L. Kowalke

THE measurement and control of temperatures have assumed positions of great importance in many industries. The manufacturers of byproduct coke and carbureted water gas find that proper temperature control helps to produce a better product and economizes in the use of raw materials. In the manufacture of glass, enameled ware, brass, and high-temperature refractories, temperature control is now regarded as being coordinate in importance with the control of materials used. To control such processes as malleablizing cast iron, and hardening, tempering, and annealing of steel in a manner to meet exacting market requirements has, within recent years, involved the installation of large and expensive pyrometer equipments. In many of these installations, it was necessary not merely to measure but also to record the temperatures over a period of time and thus obtain a record of the entire heat treatment and an effective check on the workmen in charge. In view of the importance of temperature measurement and control in such a wide variety of industries and the necessity for proper supervision of the installation and operation of the outfits, the following questions may be pertinent: What instruction is offered by the engineering colleges and what departments in the colleges are responsible therefor? The latest available catalogs of ten prominent engineering colleges east of the Mississippi River showed courses in high-temperature measurements given by the departments of physics. These courses, in general, were described as comprising classroom and laboratory instruction in the theory of high-temperature measurements, together with exercises in the calibration of the various devices used. In some cases it was stated that consideration would be given, in the courses, to the practical applications in the industries. In only one. college was the course required of all engineering students; in most colleges it was optional; in a few colleges, it was required only of certain groups. In colleges offering a course in metallurgical engineering, instruction in pyrometry was always given in connection with metallurgical laboratory work. The students in ceramic,

Jan 8, 1919

By Lawrence Adler

For openings in bedded rocks, analyzed by simple beam theory, it has been shown that roof loads can be shifted from one support to another.' This transfer is effected by controlling the relative deflection of adjacent supports. If this action is used to reduce loads in the props or bolts and increase them in the ribs or pillars, it could be productive of economies averaging 30 pct. Such savings can be realized by: 1) using smaller artifical supports such as props and bolts, and 2) increasing loads in the rib to induce eventual failure for longwall caving. Since the rib is relatively load-insensitive, it provides a natural load sink. However, caution must be used in applying such permissive deflections, for while the supports are being handled properly, the stresses in the roof itself are very sensitive to such manipulations.'

Jan 5, 1960

By William E. Schoeneck

This paper presents the problem of oil-well abandonment as a group of studies involving the compilation of physical well data, the use of special curves, maps, and interpretative Procedures, in order that operations can be analyzed and means for reducing costs can be effected. Methods for the calculation of the economic limit of production and resultant oil reserves are suggested in order that profitable production may be continued and premature abandonment prevented. INTRODUCTION Purpose Extensive studies have been made and much has been written on the procedures for prospecting, drilling, completion, production and repair of oil wells, but the writer has long felt the need for a study of the procedure that should be followed when considering the abandonment of a well. The production from numerous well bores of a fluid material (a circumstance peculiar to the oil industry) that is continually decreasing in quantity leads to an increasing ratio of operating cost to production. It is for this reason that oil fields are not abandoned as a whole and detailed consideration of each well is required before it can be determined whether more is being expended than will be returned On any well or lease in question. It is the purpose of this paper, therefore, to compile, correlate, and present all matters worthy of consideration in the problem of oil-well abandonment; to suggest interpretative procedures based on such compilations, to the end that reliable estimates of reserves and life may be obtained; to show, as a result of such interpretative procedures, the possibilities for corrective measures conducive to economical production, thereby extending both profitable reserves and length of life. Scope and Approach Compiling data and outlining a study having the complexity of the problem at hand are naturally subject to the personal experiences of one who undertakes the study; however, the chosen approach and grouping of the subject material may be helpful in the consideration of abandonment problems. Consideration has been given to wells that make gas and water incident with the production of oil; but consideration has not been given to either gas wells or condensate-producing wells, for wells of the latter type have sufficient problems to warrant separate investigation. The major subdivisions of this paper-— physical considerations and economic considerations—do not imply that either of these phases can be considered independently, but rather that the two are mutually dependent and are the component parts of an engineering study.

Jan 1, 1946

By William E. Schoeneck

This paper presents the problem of oil-well abandonment as a group of studies involving the compilation of physical well data, the use of special curves, maps, and interpretative Procedures, in order that operations can be analyzed and means for reducing costs can be effected. Methods for the calculation of the economic limit of production and resultant oil reserves are suggested in order that profitable production may be continued and premature abandonment prevented. INTRODUCTION Purpose Extensive studies have been made and much has been written on the procedures for prospecting, drilling, completion, production and repair of oil wells, but the writer has long felt the need for a study of the procedure that should be followed when considering the abandonment of a well. The production from numerous well bores of a fluid material (a circumstance peculiar to the oil industry) that is continually decreasing in quantity leads to an increasing ratio of operating cost to production. It is for this reason that oil fields are not abandoned as a whole and detailed consideration of each well is required before it can be determined whether more is being expended than will be returned On any well or lease in question. It is the purpose of this paper, therefore, to compile, correlate, and present all matters worthy of consideration in the problem of oil-well abandonment; to suggest interpretative procedures based on such compilations, to the end that reliable estimates of reserves and life may be obtained; to show, as a result of such interpretative procedures, the possibilities for corrective measures conducive to economical production, thereby extending both profitable reserves and length of life. Scope and Approach Compiling data and outlining a study having the complexity of the problem at hand are naturally subject to the personal experiences of one who undertakes the study; however, the chosen approach and grouping of the subject material may be helpful in the consideration of abandonment problems. Consideration has been given to wells that make gas and water incident with the production of oil; but consideration has not been given to either gas wells or condensate-producing wells, for wells of the latter type have sufficient problems to warrant separate investigation. The major subdivisions of this paper-— physical considerations and economic considerations—do not imply that either of these phases can be considered independently, but rather that the two are mutually dependent and are the component parts of an engineering study.

Jan 1, 1946

By H. H. Reamer, B. H. Sage

Attempts have been made to predict the volumetric and phase behavior of naturally occurring hydrocarbon mix-turesl-6 but these methods have not been extended to the higher pressures and tem-peratures that are currently encountered in some producing formations. Furthermore, the methods of prediction at present avail-able have not been tested in a sufficient number of cases to ensure their applica-bility to all naturally occurring hydrocar-bon mixtures, even at the lower pressures and temperatures. For these reasons the behavior of a number of hydrocarbon mix-tures from a field in which the subsurface pressures are above 4500 lb. per sq. in.t and the temperatures are in the neighbor-hood of 250°F. was investigated. Method The objective of this program was to determine the volumetric behavior of ma-terial as it existed in the reservoir as a function of pressure, temperature and com-position. Strictly speaking, this cannot be accomplished in any simple fashion. How- ever, the variations in composition that are encountered within a producing reservoir may be approximated roughly by means of mixtures made up of two arbitrarily chosen constituents. Experience indicates that the liquid and gas phases from a high-pressure gas trap afford a simple source of material for this purpose. Throughout this discus-sion the samples of the gas phase and liquid phase from the production trap will be called the "trap-gas sample" and the "trap-liquid sample," respectively. The volumetric behavior of both of the trap samples was determined throughout the temperature interval between 100" and 250°F. at pressures up to 5000 lb. per sq. in. In addition, the behavior of eight different mixtures containing varying proportions of the two trap samples was studied throughout the same temperature and pressure intervals. The experimental results yielded information concerning the specific volume of the material as a function of pressure, temperature and the relative quantity of the trap samples. The relative amount of each of the paraffin hydrocarbons of lower molecular weight than n-hexane was determined for each of the trap samples. In addition, the specific weight, viscosity and average molecular weight of the hexanes-and-heavier fraction of the trap-liquid sample were determined as well as similar information for each of five fractions separated from this material by distillation. From these data the weight fractions of each of the components from methane through pentane were determined for the trap samples and eight systematically chosen mixtures. Materials The gas and liquid samples were obtained from the production trap of a well in the Rio Bravo field in California during the fall of 1939. Information concerning the condi- 70

Jan 1, 1941

By H. H. Reamer, B. H. Sage

Attempts have been made to predict the volumetric and phase behavior of naturally occurring hydrocarbon mix-turesl-6 but these methods have not been extended to the higher pressures and tem-peratures that are currently encountered in some producing formations. Furthermore, the methods of prediction at present avail-able have not been tested in a sufficient number of cases to ensure their applica-bility to all naturally occurring hydrocar-bon mixtures, even at the lower pressures and temperatures. For these reasons the behavior of a number of hydrocarbon mix-tures from a field in which the subsurface pressures are above 4500 lb. per sq. in.t and the temperatures are in the neighbor-hood of 250°F. was investigated. Method The objective of this program was to determine the volumetric behavior of ma-terial as it existed in the reservoir as a function of pressure, temperature and com-position. Strictly speaking, this cannot be accomplished in any simple fashion. How- ever, the variations in composition that are encountered within a producing reservoir may be approximated roughly by means of mixtures made up of two arbitrarily chosen constituents. Experience indicates that the liquid and gas phases from a high-pressure gas trap afford a simple source of material for this purpose. Throughout this discus-sion the samples of the gas phase and liquid phase from the production trap will be called the "trap-gas sample" and the "trap-liquid sample," respectively. The volumetric behavior of both of the trap samples was determined throughout the temperature interval between 100" and 250°F. at pressures up to 5000 lb. per sq. in. In addition, the behavior of eight different mixtures containing varying proportions of the two trap samples was studied throughout the same temperature and pressure intervals. The experimental results yielded information concerning the specific volume of the material as a function of pressure, temperature and the relative quantity of the trap samples. The relative amount of each of the paraffin hydrocarbons of lower molecular weight than n-hexane was determined for each of the trap samples. In addition, the specific weight, viscosity and average molecular weight of the hexanes-and-heavier fraction of the trap-liquid sample were determined as well as similar information for each of five fractions separated from this material by distillation. From these data the weight fractions of each of the components from methane through pentane were determined for the trap samples and eight systematically chosen mixtures. Materials The gas and liquid samples were obtained from the production trap of a well in the Rio Bravo field in California during the fall of 1939. Information concerning the condi- 70

Jan 1, 1941

By Lloyd Pollish, Robert N. Breckenridge

SUCCESS in any underground mining operation is determined by accessibility of the orebody, which in turn is dependent upon maintenance of passage- ways to the mining zones and temporary support of the voids caused by extraction of ore. This is accomplished by one or a combination of the following methods: timbering, back-filling, pillaring, or, more recently, rock bolting. Timbering has usually been the principal means of maintaining these underground openings necessary for mining operations. Timber, however, does not prevent ground movement beyond the scope of localized sloughing, which is indicated by the gradual failing of the timber itself. Besides this, timbering has always been a costly process, and with the decline of available supplies of timber close to the mining areas, mining men have constantly sought other methods of controlling ground.

Jan 7, 1954

By N. A. Gokcen

THE data of Chaudron,1 Tonosaki,2 and Collins³ on the thermodynamic properties of MOO, disagree widely. These authors, by using essentially similar methods, studied the following reaction: 1/2MoO2(s) + H2(g) == i/2Mo(s) + Ph,o H2O(g),K = —----- [1] Ph2 Tonosaki used a vacuum system consisting of a furnace containing MOO, and a water saturator whose temperature was kept at 25 °C with a thermostat. After repeated evacuation, hydrogen was admitted slowly into the system. The experiments were based upon the fact that at a constant furnace temperature and constant partial pressure of water, the total pressure of gas mixture over MOO? + Mo is constant. Any attempt to vary the pressure by external forces would vary only the amounts of MoO2, and Mo, after which the pressure should return to the equilibrium value in accordance with the equilibrium constant of reaction 1. The actual value of K was determined from the total equilibrium pressure (sum of Ph2o + Ph2) at each temperature. The total pressure of gas was varied within the range of 80.2 to 125.4 mm Hg, within a temperature range of 645" to 823 °C. The results were summarized as log K = 0.9413 — 1444.6/T for reaction 1. The ratio of H2O/H2 was considered to be uniform in spite of the presence of a thermal gradient across the static gas phase. It was shown by Rosenqvist and Cox,' however, that in somewhat similar circumstances the error resulting from thermal diffusion may be large. Collins³ improved Tonosaki's method by attempting to avoid thermal diffusion errors. His equilibrium data were obtained at 700°, 800°, and 900° C, and the result for reaction 1 was expressed as log K = 1.258 — 1822/T. The purpose of this investigation was to study reaction 1, avoiding the thermal diffusion errors, and to obtain equilibrium data in a considerably wide temperature range for the reliable extrapolation of the resulting thermodynamic functions. Experimental Procedure The diagram of the apparatus is shown in Fig. 1. Tank hydrogen was passed through a tube containing platinized asbestos at 425 °C in order to convert a trace of oxygen into water vapor. The flow rate was carefully controlled with a capillary-type flow-meter B and a bubbling column D. The gas was then presaturated sufficiently at P and led into a condenser system immersed in a thermostat, controlled to within ±0.002C. The temperature of the thermostat was measured with a thermometer calibrated against a certified standard. The temperature of P was adjusted to avoid the condensation of unduly large amounts of water as judged from the rate of flow out of the capillary tube M. Argon was purified by passing it through magnesium chips kept at 630°C. After passing through the flowmeter B', it was mixed with moist hydrogen emerging from the thermostat. The resulting gas mixture was then led into the hot zone of the furnace through the heated glass tubing and the silica tube S, thus insuring the same ratio of PII2o/Ph2 from the condenser to the reaction chamber, thus avoiding thermal diffusion. The entire gas system was of all-glass construction, except at the magnesium train. The furnace comprised a glazed alumina tube over which a 15-in. platinum coil was wound. The lower end of the alumina tube was tightly closed with a brass bottom and a silicone rubber gasket, and the upper end with two glass disks, each with a hole of 1/16 in. in diameter, through which the gas mixture escaped into the atmosphere. A back-up coil of kanthal wire facilitated the temperature control of the furnace. A coil of annealed molybdenum strip of 99.99 pct purity, 0.005 in. thick and 0.050 in. wide, and weighing 17 g was hung in the furnace with a 0.010-in. platinum wire attached to one end of a sensitive analytical balance. The temperature of the furnace was measured with a Pt-Pt-10 pct Rh thermocouple checked against a standard. The experimental procedure consisted of heating the gas purification trains, adjusting the gas flow rates, attaining a constant thermostatic temperature, flushing the entire system for 2 hr while heating the furnace to well above the expected equilibrium temperature and then cooling it at a rate of 0.3°C per min during which time the change in the weight of molybdenum was observed on the balance. For a given thermostatic temperature, i.e., a constant Prr,o/Px,, molybdenum oxidized upon cooling slightly below the equilibrium temperature. The procedure was then repeated by heating the furnace and thus reaching a temperature slightly above the equilibrium value. The average of the two temperatures, differing by 2" to 3"C, was considered to be the true equilibrium temperature. In order to determine the stoichiometric composition of the oxide phase present in this investigation,

Jan 1, 1954

By Franz Wever

ACCORDING to Tammann,1 the explanation of the effect of mechanical deformation in producing changes in the properties of metals is one of the most important problems of physical metallurgy, taking rank with the study of the constitution of alloy systems; and this problem has long attracted-the attention of practitioner and scientist alike. Its solution was not advanced materially until Tammann2 set up his translation hypothesis with its crystallographic basis, while other hypotheses, such as the amorphous metal hypothesis of Beilby3 and Rosenhain,4 have been shown by more intensive studies to be less and less satisfactory. The principles of the Tammann translation hypothesis have proved to be useful even up to today and in spite of all of the recent accumulation of experimental data, while the differences of opinion which have arisen relate to the extent to which the hypothesis accounts for the observed changes in properties and to what extent further assumptions are necessary. Stimulated by the proposals of Tammann, there soon developed a lively experimental activity which aimed at the elucidation of the structural or crystallographic changes produced by the mechanical deformation of metals. Parallel movements of crystal "blocks" along definite crystal slip planes had already been observed by lowing and Rosenhain5 in 1900, in metals which had been moderately deformed but without shedding light on the crystallographic nature of the processes accompanying more severe deformation. The solution of this important problem was not advanced until a much later date, or until the methods of X-ray crystal analysis had become available. Shortly after the discovery of the diffraction of X-ray by crystals, symmetrical diffraction effects were

Jan 1, 1931

By John Wulff, H. H. Uhlig

Since its first mention in the literature in the eighteenth century12 the phenomenon of passivity in metals has stimulated much speculation and attendant controversy as to its nature and cause. No one of the numerous theories so far proposed has been generally accepted. ‡ Faraday,' in 1836, associated the passivity of iron with a protective film over the surface of the metal, which materially prevents or slows down reaction with corrosive environments. His theory was that oxidizing acids like nitric acid form an unstable oxygen or oxide layer over the iron surface, which protects the underlying metal from further attack. This concept was simple yet plausible, and without alteration has frequently been assigned in present-day discussions as explanation of the passivity of many metals. With the advent in recent times of stainless steels, it is not surprising that this oxide film theory of passivity proposed by Faraday has been used to explain the phenomenal corrosion resistance of stainless steels and other passive alloys. The passive alloys, such as the chrome-iron alloys, are supposedly covered with a protective oxide film, which forms on exposure of the alloy to air, is extremely stable and self-healing, and accounts for the remarkable resistance of these alloys to corrosion. Within the past few years, several investigators, following the theory of film protection, have attempted to gauge the resistance of the supposed film on steels. Brennert8 and Donker and Dengg9 determined the potential at which a negative ion (e.g., C1-) moving in an electric field reacted with the metal anode, as detected by increased current flow or change in potential of the steel electrode in an electrolytic cell. The potential corresponding to reaction Brennert called the film break-through potential.

Jan 1, 1939

By John Wulff, H. H. Uhlig

Since its first mention in the literature in the eighteenth century12 the phenomenon of passivity in metals has stimulated much speculation and attendant controversy as to its nature and cause. No one of the numerous theories so far proposed has been generally accepted. ‡ Faraday,' in 1836, associated the passivity of iron with a protective film over the surface of the metal, which materially prevents or slows down reaction with corrosive environments. His theory was that oxidizing acids like nitric acid form an unstable oxygen or oxide layer over the iron surface, which protects the underlying metal from further attack. This concept was simple yet plausible, and without alteration has frequently been assigned in present-day discussions as explanation of the passivity of many metals. With the advent in recent times of stainless steels, it is not surprising that this oxide film theory of passivity proposed by Faraday has been used to explain the phenomenal corrosion resistance of stainless steels and other passive alloys. The passive alloys, such as the chrome-iron alloys, are supposedly covered with a protective oxide film, which forms on exposure of the alloy to air, is extremely stable and self-healing, and accounts for the remarkable resistance of these alloys to corrosion. Within the past few years, several investigators, following the theory of film protection, have attempted to gauge the resistance of the supposed film on steels. Brennert8 and Donker and Dengg9 determined the potential at which a negative ion (e.g., C1-) moving in an electric field reacted with the metal anode, as detected by increased current flow or change in potential of the steel electrode in an electrolytic cell. The potential corresponding to reaction Brennert called the film break-through potential.

Jan 1, 1939

By C. G. Palagi, S. S. Stillar

The C. E. Weed concentrator treats 51,000 tons per day of 0.5% to 0.7% copper ore received from the Berkeley Pit, the Continental East Pit and the Butte underground mines. Improved operating techniques and conversion from semi-autogenous secondary grinding to ball milling have increased tonnage from an original design of 42,000 tpd. Separate treatment of sands and slimes, with recovery of soluble copper from the slimes, has increased total copper recovery. Concentrator tailings are pumped 600 vertical feet and 20,000 horizontal feet for disposal.

Jan 1, 1976

By William Laird

The predominent method of coal mining in the United States for years has been room-and-pillar mining. The reason for this has been the advantages of room-and- pillar method which is a relatively flexible system and its capital investment. The room-and-pillar method permits some selectivity in mining, especially where gas wells, faults and possible coal quality may be a factor. The mobility of continuous and conventional mining equipment used to develop entries may also be used for retreat mining of rooms and pillars. Longwall mining of coal takes place along a long straight face, or wall, blocked out between two butt or panel entries. The long faces or walls are normally projected in lengths of 61 to 183 m (200 to 600 ft) in this country. The longwall method of mining had its beginning in the United States during the 1800's. During that period, pack wall and wood posts were used for roof support. The longwall face was mined by miners using picks to undercut the coal. To keep the coal face from turning over, short wood posts called sprags were set in a slant position as the coal face was undercut to the depth of two to three feet. When the under-cutting cycle was completed, the sprags were removed to permit the coal to fall from the roof pressure. The longwall mining of coal did not take a firm hold during the 18009s, and room-and-pillar prevailed. In the early 19009s, steel jacks were introduced, and along with it, the modified caving theory. In March of 1950, a retreat longwall mining system, utilizing a plow, manually operated props, wood cribs and chock releases, was installed in one of Eastern Associated Coal Corp.'s mines.

Jan 1, 1981

By H. J. Levinstein, H. J. Guggenheim

RbFeF3 is a transparent ferromagnet with a large faraday rotation which permits the direct observation of magnetic domain structures in bulk crystals. If the position of dislocations within the crystal were known a study of domain wall dislocation interactions would be possible. In this paper an etch pitting solution is described which gives a one-one correspondent between the etch pits and the dislocations intersecting the (100) surfaces of RbFeF3 crystals. In addition, RbFeF3 is shown to have sufficient plasticity so that known arrays of dislocaticms can be put into the crystal. It is concluded that RbFeF, is an ideal material for the investigation of domain wall dislocation interactions. THE influence of lattice defects on the motion of domain walls in ferromagnetic materials has been studied extensively both theoretically and experimentally.4 The experimental data obtained has been qualitative in nature due to the lack either of a quantitative knowledge of the magnetic domain array in the material or of the nature of the dislocation configuration in the material. At room temperature RbFeFJ has the cubic perovskite structure. It is ferromagnetic below 86°K.5,6 It is also transparent and has a large faraday rotation in the magnetic state.7 The domain structure of this material is observable in three dimensions in crystals which are millimeters in thickness.' Since RbFeF3 satisfies the requirements of having an easily visible three-dimensional magnetic domain structure, it was of interest to determine if the dislocation structure of the material could be determined and if the material was sufficiently plastic so that dislocations could be introduced into the as grown crystals. This is a report of the results of that investigation. EXPERIMENTAL PROCEDURE The crystals of RbFeFs used in this experiment were grown by a technique described elsewhere.5 In order to obtain flat strain-free surfaces, the samples were first cut to the crystal orientation desired and the surfaces were polished by employing standard metallographic techniques. The samples were then immersed in a solution of 1 to 3 g of KOH in 100 ml of water. This solution removes the damaged surface layers uniformly leaving a film on the surface of the sample. Etch pits are obtained by immersing the sample in an approximately 50-50 solution of 30 pct peroxide and concentrated acetic acid. The film formed during the KOH treatment turns deep red in color in the etching solution and flakes off the sample. The etching time required depends upon the pit size desired and

Jan 1, 1970

By R. Schuhmann Jr., P. J. Ensio

As a first step in a study of the physical chemistry of copper-smelting slags, experimental measurements were made of the oxygen pressure of simple iron-silicate slags in equilibrium with solid iron. The experiments consisted in bubbling CO2-CO mixtures through the slags in iron crucibles and in finding the equilibrium ratios of CO2 to CO. From the data, activities and partial molal heats of solution FeO and SiO2 in the slags were calculated. THE ternary system FeO-Fe,O,-SiO, is the simplest system which can represent adequately the important chemical properties of the slags formed in matte smelting and converting. Accordingly, the experimental study of slags in this system was started as the first step in a general research program on the thermodynamics of copper smelting. A recent paper by one of the authors' outlines this general research program and shows in some detail how information on thermodynamic properties of iron-silicate slags, especially information on oxygen activities, is essential to a full understanding of the chemistry of copper smelting. The FeO-Fe,O,-SiO, system also is the basis of slags produced in other processes, such as acid steelmak-ing processes, and is important in relation to the behavior of silicious refractories. In addition, data on the physicochemical properties of iron-silicate slags should contribute to a general understanding of the nature of slags, since at present such data for all kinds of slags are relatively meager. The principal quantitative information already available on iron-silicate slags consists in Bowen and Schairer's constitution diagram for slags in equilibrium with metallic iron,' Darken and Gurry's complete and precise thermodynamic study of the Fe-0 system,",' and Darken's study of the phase equilibria in the Fe-Si-o system. From the results of this previous work, it was clear that a complete thermodynamic study of ternary iron-silicate melts was a major undertaking which would have to be broken down into parts, including the working out of the ternary equilibrium diagram as well as extensive activity measurements on slags. The experimental measurement of oxygen activity, using CO-CO, and other gas mixtures as yardsticks of oxygen activity, was the basis of Darken and Gurry's study of the Fe-0 system. From the experimental measurements of oxygen activities over a large range of temperatures and compositions, they were able to calculate the activities of other species such as Fe, FeO, Fe,O,, etc., and also the other important thermodynamic properties in the Fe-0 system. At the start of the present investigation, it appeared that the same approach would be fruitful for the study of iron-silicate melts. Also, the experimental measurement of oxygen activities seemed particularly attractive because oxygen activity itself is a quantitative measure of oxidizing or reducing power, which is an important variable in copper-smelting slags. The slag compositions in equilibrium with yFe appeared most suitable for the first investigation of this kind, for the following reasons: 1—Good constitution data2 were available. 2—An iron crucible could be used, thus affording a simple solution to the refractory problem without introducing contarnination. 3—With Fe activity fixed, at unity with respect to a standard state of solid Fe, measurements of 0 activity could be followed by simple calculations of activities of FeO and other Fe-0 complexes and of SiO,. 4—This starting point afforded several possibilities for cross-checking with previous work,

Jan 1, 1952

By Kichizo Niwa, Toshio Yokokawa, Mitsuo Shimoji, Yoshihiko Watanabe, Satoshi Kado

A LTHOUGH a systematic research on diffusion in liquid metals has not been carried out, partial studies have been developed by various workers in several systems. A few recent papers among them have shown that this line of approach is quite useful for understanding the structure of the liquid state. Furthermore, it has been found in kinetic

Jan 1, 1958

By E. M. Wise

MANY of the platinum metal alloys are hot-forged in the early stages of reduction from ingot and substantial quantities of platinum alloys are commercially employed at very high temperatures in ammonia oxidation units, orifices for forming glass rods and fibers and as cathodes in long-life thermionic amplifiers. They are used also for electrical heating resistors, safety blowout disks, thermocouples and crucibles. The tensile prop-erties at elevated temperatures are important in many of these situations but data on the subject are limited. Creep data also are important, but will not be covered at this time. SCOPE AND CONCLUSIONS Tensile tests were carried out at room temperature and elevated temperatures up to 1100° C. on previously well annealed samples of platinum, palladium and several of their important alloys with composi-tions shown in Table 1. The results are presented graphically in Figs. 1 to 4. The tensile strengths of platinum and the platinum-base alloys (with the exception of the 10 per cent rhodium-platinum alloy) at 1100° C. are from 16.6 to 18.8 per cent of the strengths of the same alloys (well annealed) at room temperature. The strength ratio of the 10 per cent rhodium-platinum alloy is 22.3 per cent, which is appreciably higher than that of the other materials tested.

Jan 1, 1938

By J. T. Eash, N. B. Pilling

As a group, the alloys of iron, nickel and carbon are, in application, one of the most versatile of the ferrous alloy family, and while many investigations have been made of their properties and structure only a few attempts have been made to show the microstructural relation over a wide range of composition. It is necessary at once to be clear about the kind of structural relation with which we are concerned. The equilibrium diagram provides quantitative data regarding structural make-up and its variation with temperature, but equilibrium structures often are far different from the technologically significant ones. This is particularly true of steels and cast irons, and some of the most important components of their structure may have no place in the diagram of equilibrium. The fugitive phases that result from transformation are dealt with in a highly detailed and descriptive manner in the S-curves originated by Bain. The present effort lies in a still different field, which is to portray the relation between sweeping changes in composition and in resultant structure, under controlled but nonequilibrium conditions of thermal treatment. The Guillet1 diagram presented in 1903 was the initial attempt at such a correlation and frequent references to this diagram can be found in the literature even though later work has shown it to require considerable modification. Kase2 published in 1925 a diagram that was based upon observations of furnace-cooled melts. At low carbon contents this diagram agreed fairly well with experience in showing pearlite to exist in alloys containing up to 6 per cent nickel, and completely austenitic steels at 24 to 28 per cent nickel. At high carbon contents, however, irons were indicated as being martensitic at around 2 per cent nickel and austenitic at 12 per cent nickel; these interpretations are open to serious question. Based upon experience with steels and cast iron, Wickenden3 suggested a diagram that agreed fairly well with Kase's in the steel range but which presented a wide departure from it in the higher-carbon, high-nickel regions. In its broad picture, the Wickenden diagram is an approach to "practical" structures. [ ] Reference may be made at this point to the efforts of Marshy to construct an iron-nickel-carbon equilibrium diagram by the coordination of scattered data, which are described at length in the monograph cited. None of these preceding attempts has appeared to meet the need for an exposition of the structural sequence that is encoun-

Jan 1, 1942

By F. C. Frischknecht

Most early development and application of electromagnetic prospecting methods took place in Scandinavia, where geological conditions favor their use. In other parts of the world these methods have aroused cycles of interest, but in Scandinavia they have been used continuously and successfully since the 1920's. Electromagnetic methods may be classified into two general groups. One group includes methods in which the source of the electromagnetic field remains stationary while the receivers are moved about to explore the area. The other includes procedures in which the energizing and receiving systems are moved together. Other classifications could be based on the size of the energizing source, the particular components of the electromagnetic field which are measured, or the mode of transporting the equipment. The difference between fixed-source and moving-source methods, however, is of such great fundamental importance that it will be emphasized in this discussion. FIXED-SOURCE METHODS Essentially, a fixed-source method consists of the measurement of electromagnetic fields about the source. The mutual coupling between the source and the earth is constant, but the mutual coupling between the receiver and the earth (unless the earth is homogeneous) and also between the source and the receiver changes at each station. The results are usually normalized by relating the field data to the calculated free space or primary field. Turam and Radio Reference Signal Methods: The turam or two-frame* (see Fig. 1A) is probably * Turam means two-coil. the most common fixed-source method. The energizing source is an insulated cable grounded at both ends or formed into a large rectangular loop. Measurements are taken along a traverse at 5 to 50-meter intervals using two small receiving coils, the lagging coil being placed at the position previously occupied by the leading coil. The complex ratio (i.e., inphase and out-of-phase ratios) of the voltages induced in the two coils is measured. Operating frequency range is about 100 to 800 cps. In a typical turam survey a straight, grounded cable several kilometers long is laid out parallel to the probable strike of the ore deposits or conducting strata being sought. An area extending 1 or 2 km on each side of the cable, and within 1 or 2 km of the ends of the cable, is surveyed. Measurements are made at stations 5 to 25 m apart along traverses perpendicular to the cable. Measurements may be made along lines parallel to the cable to serve as base lines for the traverses or for other special purposes. Commonly the receiving coils are oriented with their planes horizontal so that only the vertical component of the field is measured. If additional information is required, one of the hori- zontal components may also be measured by orienting the coils with their planes vertical. In a modified turam technique developed recently for both ground and airborne measurements (Fig. 1B) the amplitude of the complex voltage induced in a single receiving coil is measured and its phase compared with that of a reference signal transmitted from the energizing system by a radio frequency carrier. Thus the un-normalized field is obtained directly, whereas with the turam method it is obtained by calculation from the ratios. The turam method and its modifications have a greater working depth than the other electromagnetic procedures used in ore prospecting. Under favorable conditions conductors have been located at depths of 200 to 300 m. A modified turam method with one of the electrodes grounded in the upper end of a plunging orebody was used to follow the extension of this body to a depth of 200 m beneath a layer of conducting schists. Straight grounded cables are usually preferred to insulated loops because they are easier to lay out and because they often make the method more sensitive. The greater sensitivity of a grounded cable is a result of ground return currents which may flow in the orebodies in addition to the eddy currents caused by induction from the current in the cable. Anomalies in the vertical field due to eddy currents are characterized by a correspondence between high values for the inphase component and positive out-of-phase components and/or low values for the inphase component and negative out-of-phase components. Also the inphase component may approach zero, but it does not become negative. In very long continuous conductors that are parallel to a grounded cable the effect of ground return currents may far exceed the effect of eddy currents. These ground return currents cause a lack of correspondence between the inphase and out-of-phase components and may cause negative inphase or anti-phase components. It becomes difficult to carry out the measurements and often difficult to interpret the results. Such results immediately suggest the presence of graphitic strata, however, since ore deposits are rarely extensive enough to accumulate sufficient ground return current to cause these results. A cable laid out perpendicular to the strike or an insulated loop is sometimes used in areas where graphitic schists and slates are present. Anomalies are then completely or almost entirely due to eddy currents and are easier to interpret. The measured voltage ratios are normalized by either subtracting or dividing by normal field ratios calculated from free space considerations. The normalized ratios are then plotted as individual profiles. When significant anomalies occur in the ratio measurements, the actual normalized fields are calculated by beginning with a measured or an assumed value for the field at a point near the cable and successively multiplying this value by the normalized ratios. There is a similarity between this process and a numerical integration of the ratio curve. Conversely, in many respects the ratio curve is similar to the first derivative of the field curve.

Jan 1, 1960