Search Documents

F. G. SMITH.-Probably someone will ask whether I discovered why the bottoms of the large shells broke out. I did not, as a result of this investigation. An experiment was made along the lines indicated in this paper, to determine whether abnormal grains greatly affected the physical properties of brass. Two ordinary test bars were annealed for 1/2 hr. at 750° C. and physical properties determined on one. The other was covered with indentations made with a peen hammer and then reannealed. for 5 hr. at 750° C. It was found in the tensile test to be made up of large grains 1/4 to 1/2 in. in diameter. The physical properties, however, differed from those of the first bar only as much as might be expected after a 5 hr. anneal under normal conditions. It appears then that the large grains produced in this manner do not ruin the physical qualities of the brass.

Jan 12, 1919

By J. V. W. REYNDERS

IN THE remarks which I am about to make concern¬ing the safety work of the Bureau of Mines, I want first of all to disengage myself from a disposition, which is frequently in evidence, to give spectacular emphasis to the hazards of mining operations. It is of the' utmost importance to the industrial welfare of our country that the enormous annual requirement of fuel be produced and be made available in our economic activities, with a minimum of distress and hardship. The safety of coal mining is a condition with which. we are all concerned in a fundamental way. And yet we should not rush to accept hastily conceived notions that laxity among employers in respect to safety measures exists to any outstanding degree. In fact in a large number of instances, the precautionary efforts of min¬ing companies, directed to the elimination of accidents are beyond all criticism, albeit the industry suffers in reputation from the carelessness of, its less effi¬cient constituents. The Bureau of Mines has been a leading influence in disseminating the doctrines of safety, in securing the cooperation of the miners themselves, and in stirring up ' the laggards, both among the employers and the employed. It is much to the interest of well-conducted mine operations that the industry, as a whole, observe safety regulations to the utmost.

Jan 1, 1925

By R. F. Lynch, J. D. Wood

The Al-1.0 pct Mg alloy 565 7 was studied using optical microscopy and electron microprobe X-ray analysis. Constituent particles were found to exist inter-dendritically in the as-cast material in a region of precipitate free a -aluminum. Five phases besides a fine precipitate and a-Al were identified in the cast structure: Fel3, Fe2Al7, Mg2Al3, CUMgAl2, and Cu2FeAl7. Thermal treatments conducted for 100 hr at 1180°, 1130°, 1080°, 1030°, 980°, and 880° F revealed a general dissolution and spheroidization of the in-terdendritic constituent network observed in the cast structure. The principal constituents present in the thermally treated structures were FeAl3 and Fe2Al7 with the relative amount of Fe2A17 to FeAl3 increasing with a decrease in the treatment temperature. The phases Present in the wrought structure were identical to those observed after the thermal treatments, with the constituent particles strung out in the direction of rolling. ALLOY 5657 is a nonheat-treatable commercial purity Al-1.0 pct Mg alloy utilized extensively because of its bright finishing characteristics. This investigation was conducted to determine the constituents present in 5657 alloy, and to study the effect of extended thermal treatments on morphology. Numerous studies have been carried out to establish the equilibrium diagrams for various aluminum systems,1-3 with phase identification based on X-ray analysis, morphology, and the etching response of relatively large particles. Phragmen4 conducted a study of the phases in aluminum eutectic systems and compiled a "corrected" table of etching responses, drawing on his work plus that of Schrader,5 Keller and Wilcox,6 and Mondolfo.7 A review of the original work of Keller and Wilcox, and Mondolfo, which was concerned with the constituents found in commercial alloys, reveals that in numerous cases their etching responses differ from those reported by Phragmen and from each other. These inconsistencies may occur because a specific constituent will react to a given etch in a varying manner depending upon its size, the elements dissolved in the phase, the other constituents surrounding a phase, and the solute content of the matrix. Work with a commercial orientation was conducted on alloys 2024 and 3003 by Sperry8,9 and on alloy 3003 by Barker,10 where the relationship between the phase diagram and the nonequilibrium structure of an alloy was examined. Backerud11 investigated the A1-Fe binary system and found that at high cooling rates the equilibrium eutectic reaction forming a-A1 and FeA13 is replaced by another lower temperature eutectic reaction forming a-A1 and metastable FeAl6, a constituent first identified by Hollingsworth et al.12 Most of the above mentioned studies were conducted on materials having a significantly greater alloy content than 5657 alloy, where the relatively small size and sparse distribution of second phase particles hinders the process of identifying constituents. EXPERIMENTAL PROCEDURE Material with a composition as given in Table I was examined in the as-direct chill cast, hot rolled and cold rolled conditions, and after thermal treatment of the cast structure. Thermal treatments were terminated by a water quench. Microscopic examination was conducted under various lighting conditions following the application of standard etchants as specified in Table 11. A semi-quantitative electron microprobe X-ray analysis was conducted for Al, Mg, Fe, Cu, Si, Zn, and Ti. RESULTS AND DISCUSSION Microstructure of the As-Cast Material. Particles of second phase material were found to exist inter-dendritically, principally in regions of precipitate free a-Al, as illustrated in Fig. 1. Adjacent to the ingot edge was a region of inverse segregation, resulting in an increased amount of second phase material containing large sized particles which aided in phase identification. Phase Identification. Cast Structure. Five phases besides a-Al and a fine precipitate were identified using optical microscopy and electron microprobe X-ray analysis, as presented in Tables II and III, respectively. FeA13 and Fe2A17 are often found with Fe2A17 forming a sheath around the core of FeAl3, resulting from an incomplete peritectoid reaction. These phases have a nearly identical appearance under white light, although they are easily differentiated under crossed polarizers, as characteristically illustrated in Figs. 2(a) and 2(b), respectively. Microprobe analysis con-

Jan 1, 1970

By R. H. Hopkins, R. W. Kraft

X-ray and metallographic analysis reveal that the preferred cryslallograPhic relationships in direc-tionally solid~fied Pb-Sn eutectic specimens can be stated: interface growth direction, Experiments in which tin single-crystal seeds were used to nucleate the eutectic demonstrate that the normal lamellar structure observed at steady state can be forced to break down initially to a semide-generate structure when the crystallograPhic direction of the tin seed does not lie within the preferred eutectic interface plane. A normal structure eventually develops by preferred grain growth. X-ray topo-graphs and rocking curves substantiate that the perfection of eutectic samples increases as growth proceeds until steady-state conditions prevail. RECENT years have seen substantial progress made in the understanding of eutectic solidification through both intensive theoretical1'' and experimental investigations (see Ref. 7 for a review and extensive bibliography of both aspects). Several important observations concerning the nucleation and growth aspects of binary eutectic solidification have been brought to light. Briefly some of these include the nonrecipro-cal nucleation of one phase upon another,'j9 the tendency for a specific low-index direction of one or both phases of the eutectic to be aligned in the growth direction during unidirectional solidification,'0711 and the production of lamellar microstructures having a preferred interface plane between "11-13 phases. Questions quite naturally arise as to the mechanism by which preferred grain growth evolves during eutectic solidification and what relationships (if any) connect the initial nucleation of one phase upon another with the preferred growth directions and interface planes observed after a few centimeters of growth in many systems. This study was initiated in an attempt to answer these questions. An experiment was devised in which both the nucleation and growth steps in the crystallization of a binary eutectic, Pb-Sn, could be correlated with subsequently developed eutectic morphology and crystallography. This was accomplished by nucleating the eutectic upon a tin single crystal seed and then causing the eutectic to grow from the seed by directional freezing. The morphology of the structures produced in this manner was then monitored metallographically and the orientation relationships and substructural perfection determined by X-ray analysis. The information thus ob- tained was correlated to the growth history of the samples. EXPERIMENTAL DETAILS The eutectic of composition 38.1 wt pct Pb and 61.9 wt pct sn14 was prepared by accurately weighing lead and tin of 99.999+ (from ASARCO and Lytess Metals and Chemicals, respectively), melting in a clean Pyrex beaker under an argon blanket, and casting into the proper crucible for resolidification as described below. Tin seeds were grown by the method of ~halmers," saw-cut, oriented by the Laue method, and soldered to the pull rod of the Czochralski puller. All seeds were given a final electropolishing (to assure the removal of any deformed material from the cutting operation) and acetone degreasing immediately prior to the nucleation experiment in which they were to be used. Eutectic samples were unidirectionally solidified in a horizontal graphite boat1' or by pulling from the melt16 with tin (or graphite) seeds. A flowing argon atmosphere was employed in all experiments and growth rates and temperature gradients, constant for a given run, varied from 2 to 4 cm per hr and 8" to 15°C per cm over the course of all the experi-

Jan 1, 1969

By S. Fróes Abreu

The importation of liquid fuels in Brazil amounts to about 1,300,000 tons; 30 per cent of this total being gasoline for automobiles and airplanes. Statistics show an increasing consumption of gasoline notwithstanding the use, daily greater, of fuel alcohol, a domestic fuel of low cost in the producing areas. The Brazilian market for petroleum products has shown a tendency to grow as the country has steadily developed— expansion of the industries in the areas already developed, and also the recent occupation and population of new zones. The war has brought many difficulties to Brazil. It has limited the importation of petroleum products, which came mostly from the United States, Venezuela and Mexico. During the first days of the present crisis automobile and truck traffic was vastly curtailed; but the national activity in the production of more fuel alcohol, and principally in the development of producer gas, has done much to provide a solution for the transportation crisis threatened at the beginning of the gasoline shortage. Many thousands of cars and trucks in Brazil are now burning producer gas made from charcoal. Producer gas for automobiles has been improved by Brazilian engineers and many new types have appeared. - Production There is only one producing oil field in Brazil—the one in the State of Baia, near the Baia de Todos os Santos. The first producing oil well was drilled in Lobato in 1939 by the Federal Government following studies carried on in that area by Oscar Cordeiro, S. Froes Abreu, G. Paiva and J. Amarai. The field and laboratory work done by these men was published in 1936 in a paper entitled " ContribuicBes para a Geologiado Petroleo no Reconcavo (Baia)," which indicated the potentialities of the area as an oil producer. After the discovery of the first producing well, the Brazilian Government issued a decree establishing an area, 60 km. in radius, as a National Reservation. This first well was drilled in Lobato. In no other locality in Brazil is any petroleum produced. Although many wells have been drilled in the southern part of Brazil, on the northeastern coast and in the Amazon Basin, they yield nothing. Actual production is below 1000 bbl. daily. The producing area covers Itaparica Island, Candeias and Arath, Joanes Island and Lobato. Since very little geological information was available, especially about subsurface structure, it was necessary to drill several wildcats in order to collect the data essential in the choosing of good locations. The United Geophysical Co. was contracted to perform a geophysical survey to clear up the major problems concerning the oil deposits in the Reconcavo beds. The best wells in Reconcavo are on Itaparica Island, where the daily flow amounts to about zoo bbl.; in other sectors production is considerably lower and most of the wells are pumping. In the Aratfi sector, near an area of very light oil, there is an important gas field, with wells producing about I0,000,000 cu. ft. daily.

Jan 1, 1944

By S. Fróes Abreu

The importation of liquid fuels in Brazil amounts to about 1,300,000 tons; 30 per cent of this total being gasoline for automobiles and airplanes. Statistics show an increasing consumption of gasoline notwithstanding the use, daily greater, of fuel alcohol, a domestic fuel of low cost in the producing areas. The Brazilian market for petroleum products has shown a tendency to grow as the country has steadily developed— expansion of the industries in the areas already developed, and also the recent occupation and population of new zones. The war has brought many difficulties to Brazil. It has limited the importation of petroleum products, which came mostly from the United States, Venezuela and Mexico. During the first days of the present crisis automobile and truck traffic was vastly curtailed; but the national activity in the production of more fuel alcohol, and principally in the development of producer gas, has done much to provide a solution for the transportation crisis threatened at the beginning of the gasoline shortage. Many thousands of cars and trucks in Brazil are now burning producer gas made from charcoal. Producer gas for automobiles has been improved by Brazilian engineers and many new types have appeared. - Production There is only one producing oil field in Brazil—the one in the State of Baia, near the Baia de Todos os Santos. The first producing oil well was drilled in Lobato in 1939 by the Federal Government following studies carried on in that area by Oscar Cordeiro, S. Froes Abreu, G. Paiva and J. Amarai. The field and laboratory work done by these men was published in 1936 in a paper entitled " ContribuicBes para a Geologiado Petroleo no Reconcavo (Baia)," which indicated the potentialities of the area as an oil producer. After the discovery of the first producing well, the Brazilian Government issued a decree establishing an area, 60 km. in radius, as a National Reservation. This first well was drilled in Lobato. In no other locality in Brazil is any petroleum produced. Although many wells have been drilled in the southern part of Brazil, on the northeastern coast and in the Amazon Basin, they yield nothing. Actual production is below 1000 bbl. daily. The producing area covers Itaparica Island, Candeias and Arath, Joanes Island and Lobato. Since very little geological information was available, especially about subsurface structure, it was necessary to drill several wildcats in order to collect the data essential in the choosing of good locations. The United Geophysical Co. was contracted to perform a geophysical survey to clear up the major problems concerning the oil deposits in the Reconcavo beds. The best wells in Reconcavo are on Itaparica Island, where the daily flow amounts to about zoo bbl.; in other sectors production is considerably lower and most of the wells are pumping. In the Aratfi sector, near an area of very light oil, there is an important gas field, with wells producing about I0,000,000 cu. ft. daily.

Jan 1, 1944

By R. M. Rose, K. A. Jones

Resistive measurements ulere made on superconducting niobium single crystals in transverse magnetic fields. Crystals were grouln in both high and ulfrahigh vacua, doped with stnall quantities of oxygen, and annealed in ultrahigh vacua at temperatures from 900' to 1350°C. Maxima in the fluxoid pinr~ir~g force were observedfor the [100] and [210] directions. The increase of the critical current density with dissoved oxygen was seen to saturate at relatively low concentration. This behavior, and the variation of J, and residual resistivity (as a function of oxygen content and annealing) of both clean and dirty gassy) crystals, is seen as a consequence of the formation of clusters with (210)~b habit planes and (200)ffo common boundaries. These suboxide clusters are apparenlly stable at high temperatures and very low oxygen concentrations. It is generally known that dissolved oxygen at concentrations well below the solubility limit sharply increases the critical current density of superconducting niobium.' Such a result would not be expected if Nb-0 solutions were random, not even as the result of segregation on the scale usually encountered in solid solutions. According to the Kim-Anderson theory of flux creep,' the critical transport current density is determined by the pinning force Fp associated with some feature of the microstructure. As the Lorentz force. a or (J X R), of the transport current in the magnetic field approaches Fp, flux creep and then flux flow occur. The pinning force is expected to be quite small if the heterogeneity involved is significantly smaller than tte range of coherency which for niobium is circa 250~.~ Although the strain field of an individual oxygen atom in the niobium lattice is relatively large, it does not seem plausible that individual atoms could be so effective as to account for the data. Also, ~ramer~ found that straining and strain aging specimens containing small amounts of oxygen on occasion decreased the residual resistivity. A possible explanation for the above behavior may be found in the work of van Ooijen and van der Goot,= who found that annealing changed J, for niobium foils containing oxygen, and they attributed the changes to ordering of the oxygen atoms. This phenomenon has been observed by other investigators using X-ray and PROCEDURE Cylindrical 4-in.-diam niobium single crystals with axial orientations [ill], [110], [112], and [oo~] were grown from pure niobium, see Table I for analysis, in an ion-pumped ultrahigh-vacuum system using the electron beam floating zone technique. Total pressure during growth was lo-'9 torr: the oxygen partial pressure was less than lo-" torr, as determined by a mass spectrometer. These crystals will be referred to as the "clean" crystals. Similar crystals were also grown in another system at a pressure of 5 X 10"6 torr. These crystals will be referred to as the "dirty" crystals. Specimens 14 in. long were cut from the as-grown crystals and one end was polished down to no. 600 carbide paper smoothness. A back-reflection Laue photograph was then taken in order to fix the crystallo-graphic directions transverse to the crystal. The critical current density J,, the current density necessary to produce a voltage drop of 1.0 pv between voltage leads placed a in. apart, was determined as a function of the magnitude and direction of the transverse magnetic field and of the oxygen concentration. The technique and experimental arrangement was essentially similar to that of Tedmon et al.' In the remainder of this paper, the azjmuthal angle $ for the field H is referenced to the [ I101 direction in all four crystals, and oxygen was added in small equal increments by anodization and annealing.7 The resistivity ratio, RR, of the resistance at room ternperature to that at 4.2"K (H =7.00 kG) was determined as well.

Jan 1, 1970

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938

By Raymond D. Sloan

Development and exploration in Oklahoma showed a definite increase in 1941 over 1940 in production, wildcat activity and total well completions. Geological and geophysical work continued and possibly increased slightly in amount. Oklahoma retained third place in the ranking of oil-producing states of the nation, topped only by Texas and California, and followed by Illinois in fourth position. Production averaged 416,800 bbl. daily, a 1.7 per cent increase, as compared with 409,900 bbl. daily for the year 1940. Maintenance of the state's relatively stable producing rate resulted from the discovery of numerous small pools, the recombing of old areas, the establishment of new producing horizons, and the drilling of an increased number of marginal wells. The market for the Mid-Continent crude was strengthened materially to meet the increased demand. Coincident with a deeline in production in Illinois, shipment of Oklahoma-Kansas crude to the eastern points averaged 453,000 bbl. per day, an increase of 49.4 per cent as compared with 1940. The movement south amounted to an average of 42,000 bbl. per day, a loss of 41.7 per cent. Secondary-recovery programs in Oklahoma were given more consideration, operators realizing that in the future many pools would necessarily have to resort to this type of operation. Five permits for water-flooding were issued by the Corporation Commission during the year. These projects were in Rogers, Wagoner and Nowata Counties, in the shallow northeastern area, which has relatively extensive development of this type in the Bartles-ville sand at from 600 to 1000 ft. in depth. Gas repressuring of an individual lease in the 35-year old Glenn pool, Creek County, proved relatively successful, and after a year's operation was extended to cover a much larger area, with several operators participating. More of this type of work is expected in the future; however, it was given an initial setback when the legislative proposal authorizing secondary recovery in the Wilcox zone of Oklahoma's largest pool, the Oklahoma City pool, was pigeonholed by the committee. A continuation of the low discovery rates within the state would possibly lead to a revival of interest in the project. Many pools formerly classified as prorated areas were removed from this classification and transferred into the group of settled production. At the close of the year the issuance of the Federal Conservation Order M-68 and the interrelated Preference Rating Order P-98 caused a sharp decline in drilling operations, which is expected to continue until such operations are stabilized at a lower rate. The ultimate effect of these two orders on discoveries, production and reserves is a matter of speculation and conjecture. During the year, 2110 new wells were drilled, an increase of approximately 18 per cent as compared with the previous year. Of the total, 1235 were oil wells with a combined initial potential of 342,754 bbl. daily, 178 were gas wells with a total

Jan 1, 1942

By Raymond D. Sloan

Development and exploration in Oklahoma showed a definite increase in 1941 over 1940 in production, wildcat activity and total well completions. Geological and geophysical work continued and possibly increased slightly in amount. Oklahoma retained third place in the ranking of oil-producing states of the nation, topped only by Texas and California, and followed by Illinois in fourth position. Production averaged 416,800 bbl. daily, a 1.7 per cent increase, as compared with 409,900 bbl. daily for the year 1940. Maintenance of the state's relatively stable producing rate resulted from the discovery of numerous small pools, the recombing of old areas, the establishment of new producing horizons, and the drilling of an increased number of marginal wells. The market for the Mid-Continent crude was strengthened materially to meet the increased demand. Coincident with a deeline in production in Illinois, shipment of Oklahoma-Kansas crude to the eastern points averaged 453,000 bbl. per day, an increase of 49.4 per cent as compared with 1940. The movement south amounted to an average of 42,000 bbl. per day, a loss of 41.7 per cent. Secondary-recovery programs in Oklahoma were given more consideration, operators realizing that in the future many pools would necessarily have to resort to this type of operation. Five permits for water-flooding were issued by the Corporation Commission during the year. These projects were in Rogers, Wagoner and Nowata Counties, in the shallow northeastern area, which has relatively extensive development of this type in the Bartles-ville sand at from 600 to 1000 ft. in depth. Gas repressuring of an individual lease in the 35-year old Glenn pool, Creek County, proved relatively successful, and after a year's operation was extended to cover a much larger area, with several operators participating. More of this type of work is expected in the future; however, it was given an initial setback when the legislative proposal authorizing secondary recovery in the Wilcox zone of Oklahoma's largest pool, the Oklahoma City pool, was pigeonholed by the committee. A continuation of the low discovery rates within the state would possibly lead to a revival of interest in the project. Many pools formerly classified as prorated areas were removed from this classification and transferred into the group of settled production. At the close of the year the issuance of the Federal Conservation Order M-68 and the interrelated Preference Rating Order P-98 caused a sharp decline in drilling operations, which is expected to continue until such operations are stabilized at a lower rate. The ultimate effect of these two orders on discoveries, production and reserves is a matter of speculation and conjecture. During the year, 2110 new wells were drilled, an increase of approximately 18 per cent as compared with the previous year. Of the total, 1235 were oil wells with a combined initial potential of 342,754 bbl. daily, 178 were gas wells with a total

Jan 1, 1942

By J. L. Rodda, R. L. Wilcox, E. C. Truesdale

In recent years various problems in connection with research work on the preparation and properties of zinc-base alloys have required reliable information concerning the constitution of the zinc-rich portion of the iron-zinc equilibrium diagram. On numerous occasions rather positive indications were obtained that, for example, the solubility of iron in zinc was incorrectly represented on the current equilibrium diagrams. A careful study of all the available literature relating to the iron-zinc system led to the conclusion that much of the early work was unsatisfactory as measured by present standards of experimental accuracy, and as a result it was decided to redetermine the location of the liquidus curve and of adjacent portions of the diagram. Part I of this paper comprises a description of the experimental methods and a summary of the results by means of which the zinc-rich end of- the iron-zinc diagram has been revised in the following ways: 1. Measurements of the solubility of iron in liquid zinc by several different sampling methods, leading to a relocation of the liquidus curve. 2. Microscopic, conductivity, and X-ray studies of the solid solubility of iron in zinc, which, together with thermal analyses, have resulted in new values for the solid solubility and the eutectic temperature and composition. 3. Heating and cooling curves, obtained by a refined differential method, leading to new locations for the two peritectic horizontals. In Part I1 of the paper the attempt is made to review all of the published work having a bearing on the constitution of the iron-zinc system, and to correlate the present results, and some recently published data involving the use of X-ray technique, with the earlier work, much of which was done from 25 to 30 years ago.

Jan 1, 1936

By D. J. Jr. McAdam

RESULTS of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers. 1,2,3,4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The endurance limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By B. Fitch

This paper deals with the behavior of sedimenting suspensions. More particularly, it treats, in as organized a manner as possible, the body of knowledge, theoretical or empirical, by which one predicts the behavior of miscellaneous swarms of particles in suspension. Such knowledge is necessary for precise and economical design of equipment. While the behavior of a single spherical particle settling through an infinite sea of quiescent fluid is well understood, practical sedimentation processes are almost always concerned with particles of assorted sizes, densities, and shapes, in such concentration that there is profound particle interaction. Such swarms of particles are observed to settle in any of four markedly different manners. Which one they follow is governed by particle interaction. It is determined largely by the dilution of the suspension, and the relative tendency of the particles to cohere. TYPES OF SEDIMENTATION The relationship between the different modes of sedimentation is shown paragenetically in Fig. 1. The left side of the diagram represents particles having little tendency to cohere; the right side represents particles for which interparticle cohesion is large compared to the settling force. The vertical axis represents dilution. As seen in the diagram, sedimentation is divided into three broad fields or regimes. At high dilutions there exists a regime here named 'clarification.' Particles in clarification may settle either individually, or by collecting into separated floccules. Thus there are two different possible modes of settling in the clarification regime. It is characteristic c~f this regime that there will be no clear line of demarcation between settling suspension and a supernatant. Faster particles settle out ahead of slower ones. In batch tests there develops a gradation of both particle sizes and pulp density due to progressive depletion of the largest particles from any given pulp level.

Jan 1, 1962

By George J. Young

DURing the spring of 1910 1 visited a number of open-pit brown-coal mines and underground workings in the vicinity of Halle, Halberstadt, Leipsic, Cologne and Bonn. The notes which I took and the observations which I made at the time have been condensed and make up the principal part of this paper. Certain supplementary information has been taken from several sources which are given in the paper. The mining of brown coal is one of the important industries of Germany. The coal varies in color from dark brown to almost black and is soft like loam. Pieces of wood and strips of bark and even parts of tree trunks are frequently encountered in the excavation although the coal for the most part consists of a pulverulent, more or less matted mass of small particles of vegetal matter. It is a product between peat and lignitic coal. An analysis, taken from Coal Resources of the World shows the approximate composition of the material: Moisture, 53.73 per cent.; ash, 4.98; fixed carbon, 18.08; volatile carbon, 23.31 per cent. Thc principal characteristic is the amount of moisture. This seldom runs less than 48 per cent. The ash is usually low and ranges from 5 to 10 per cent. The sulphur content is usually less than 0.5 per cent. The heating effect of the fuel ranges from 2,000 to 2,500 calories. The commercial deposits are confined to the Tertiary period although

Jan 1, 1916

By L. C. Kern

This paper presents information on the use of a new propping agent (malleable aluminum particles) which has been used successfully for producing high-conductivity fractures. The conductivity of a packed fracture depends on the width of the fracture as well as the permeability of the propping material. It is significant that the flow capacity of a propped crack is often increased many fold by propping the crack with a sparse distribution of particles. However, the flow capacity of a sparsely propped crack can be limited by two phenomena: (I) crushing of the propping particles, and (2) embedment of the propping particles in the formation walls. Malleable aluminum particles exhibit interesting properties which tend to overcome these limitations. As high loads are applied to the particles they will deform slightly, rather than shattering. The deformation results in a greater bearing area against the formation wall. This reduces the stress on the particle and reduces particle penetration into the formation. The behavior of aluminum particles under load and the bearing capacities of serveral formation rocks have been measured in the laboratory. By properly using these data, as explained in this paper, the flow capacities of aluminum-propped cracks can be calculated for a variety of conditions. Aluminum particles have been used successfully in the field to prop fractures. Where high-conductivity fractures were needed, the aluminum-propped fractures have given greater well stimulation than could have been expected for conventional fracturing processes. INTRODUCTION The purpose of a hydraulic fracture treatment is to create a conductive channel from the wellbore out into the oil or gas formation. The word conductive is emphasized because we believe that the fracture conductivity (flow capacity) is one of the most important factors influencing fracturing results. Previous papers have pointed out the additional well stimulation that can sometimes be achieved by increasing fracture conductivity. Several years ago, we investigated in some detail the effect of fracture conductivity on productivity increases to be expeced from vertical fractures. Both electrical analog and theoretical studies of unsteady-state flow behavior were made. A discussion of the electrical analog equipment and some of the results of the study were given in a previous paper' by Dyes, Kemp and Caudle. Further details were given recently by McGuire and Sikora.5 Fig. 1 shows the remarkable influence of relative fracture flow capacity and length on well stimulation. Briefly, the study indicates the following. 1. High-permeability formations require high-conductivity cracks for best results. 2. The longer the crack, the higher the fracture conductivity required for best results. 3. If the conductivity of the crack is very large compared to the formation (i.e., flow is not being limited by crack conductivity), then the longer the fracture, the better will be the results. Judging from recently published articles,1,314 there is current interest in methods for obtaining high fracture conductivities. Hence, we would like to present in this paper a discussion of a new fracture propping process (use of aluminum particle) which we have used successfully to obtain highly conductive fractures. There are several factors which influence the conductivity of a propped crack. Conventional fracturing techniques frequently result in a crack completely packed with fracturing sand. For such conditions, the crack conductivity is the product of the width of the packed fracture and the permeability of the propping material. It is significant that a large increase in conductivity sometimes can be obtained by propping with particles which are distributed sparsely (less than a

By E. J. Ripling

TUBES may be produced by a large number of forming processes, the most common of which will be discussed analytically in this paper. In no case will the stress analysis for any given tube producing process be derived formally for where such analyses are available, they may be referred to readily. Rather, emphasis will be placed on the interpretation of the theory of the different processes, few of which are developed to a state that will allow rigorous mathematical analyses, in an attempt to give a rational description of the effects of the different variables involved in each method. Tube producing methods can be divided into two groups: Those used to form shells, and those used to further work these shells into a shape more suitable for their final use. Among the first group are included roll piercing, extrusion and cupping for seamless shells, and bending with welding for welded tubes. The re-forming processes include sinking, drawing with a plug, and drawing with a rod. Only the plastic forming operations will be discussed here; other forming processes such as casting shells will not be considered. PRODUCTION OF SHELLS Shells for Seamless Tubing Piercing: The extremely important process of forming an axial hole in a billet by oblique rolling never has been analyzed satisfactorily, although a certain amount of experimental work relating to this process has been conducted. There are a number of factors that make piercing difficult to analyze; one of these is the fact that piercing is not a problem in plasticity, but one in fracturing, and the laws of fracturing are even less well understood than those of plasticity. If, however, it is assumed that fracturing occurs on a surface as a result of tensile stresses acting normal to this surface, piercing can be analyzed qualitatively by examining the stresses established in the oblique rolling process. To determine the origin of the tensile stresses that are thought to effect piercing, it will be necessary to know the angular relationships between the maximum stresses that are established in piercing. These angles quite frequently can be determined in a plastic deformation process by an examination of the deformed product. For example, consider the stresses established when a tensile test is conducted on a rectangular cross-sectional specimen of pearlitic steel. When stretched, this material first flows plastically, exhibiting the well-known yield jog on a stress-strain curve. The formation of the slip areas that give rise to the yield jog can be detected during the straining, since these flowed areas cause depressions on the specimen surfaces which can be seen if the surfaces are polished highly. The plastically strained areas also can be found after the specimen has been stretched to a strain not exceeding the yield jog, by sectioning the test piece and. etching these sections with Fry's etch. With this etchant, it is possible to dis-

Jan 1, 1951

By AIME

The Taconites Are Ready, the editorial appearing on P. 933 of the September issue, has provoked comment from several informed engineers to the effect that the indicated profit margin was considerably exaggerated. The cost figures in the editorial, taken from the Congressional Record, were characterized as inaccurate by some correspondents. The theme of the story was, however, substantiated in the announcement (P. 1023, October) that Republic and Armco had joined forces in a $160 million project for taconite development. Chief among the dissenters was E. W. Davis, , Director of the Mines Experiment Station at the University of Minnesota. Mr. Davis has worked up the following set of cost figures:

Jan 1, 1950

[ ] Utilizing tendencies for low grade ores in the Sudbury District of Ontario to cave after higher grade ore has been mined, International Nickel Co., of Canada, Ltd., is recovering millions of tons of nickel-copper ore once regarded as submarginal. Inco is working lower grade ore than ever mined before from its underground operations because of the caving method and metallurgical practices. In the caving method, blocks containing as much as 1.5 million tons of ore are undercut. As ore from the undercut block is withdrawn, the block to be mined breaks away and starts to disintegrate as it moves downward. Inco is also using the blasthole method, using explosives to break slices of harder, tougher ore from solid material. Inco has built a new concentrator at one of its most recent shafts for handling the increased tonnages of low grade ore. The concentrator presently has a 10,000-ton per day capacity, and is scheduled to be increased to 12,000 tons. Hoisting from the mine is by push-button control and the ore is milled on the spot. A 7 ½ -mile pipeline carries bulk concentrate to reduction plants at Copper Cliff. Giant crushers, weighing 165 tons each, have been installed underground. Twenty-ton electric locomotives haul ore to the crushers. The expansion program is expected to lift total annual production of nickel in the free world to 375 million pounds annually, an increase of 150 million pounds. Inco is presently mining more than 1 million tons of ore per month from combined surface and underground operations.

Jan 1, 1952

By Charles E. Weaver

During the past few years there has been considerable activity in prospecting for oil and gas in several parts of western washington. From time to time seepages of oil or emanations of gas have been reported from various places. Several companies have been organized for the purpose of drilling, but only a part of these have actually begun operations. In certain localities very small seepages of oil occur, but up to the present time no oil or gas in commercial quantities has been obtained. In order to determine the conditions which may be favorable or unfavorable to the occurrence of petroleum it becomes necessary to know the character and extent of the geological formations in which such deposits might occur. In other regions where producing wells have been developed it is possible to know what formations contain the oil and what structural conditions influence its concentration in reservoirs or zones. It is usually possible to determine those strata which contained the materials from which the petroleum may have been derived and also the position and distribution of the more porous sandstone belts into which it may have collected. Detailed stratigraphic surveys may even determine the depth at which a certain known oil-bearing zone may be tapped at any particular place. It is also possible to recognize those formations which are presumably barren of oil, as well as those which are absolutely so. In new regions far distant from any of those which are now producing or have produced in the past, it becomes absolutely impossible to foretell whether oil may exist in commercial quantities or not. Assuming that such deposits do exist, it is extremely difficult to predict at what depth the produciqg zone or zones occur. However, in prospecting in a new and unexplored region, use should be made of such laws as have been found to govern the occurrence of petroleum deposits in other well-developed fields. Such deposits in their world-wide distribution are found almost exclusively associated with sedimentary rocks. Areas composed predominatingly of igneous and metamorphosed rocks are to be rcgarded as extremely unfavorable localities for the occurrence of commercial deposits of oil or gas. Assuming that such oil deposits are

Jan 1, 1916