Search Documents

By E. R. MARBLE

THE introduction of a new fuel, such as natural gas, necessitates careful study where it has not been used previously. At the El Paso smelter natural gas required the installation of apparatus with which no one at the plant was familiar, either as to the type of equipment needed or as to the burning of the gas in it. Observation of existing installations of a similar character and assistance from gas engineers served as a basis to determine what was advisable to use. The gas line entering the plant goes to a metering station equipped with a duplicate system of pressure regulators, a temperature recorder and the gas company and smelter orifice meters in tandem. There are three distribution lines that can be inter-connected at a later date, if necessary, to assist in equalizing the plant load. All the larger lines are of heavy

Jan 1, 1930

By Edward W. Parker

THE agreement of September, 1922, between the anthracite operators and the United Mine Workers of America, which followed the 54.5 months strike during the summer of that year, contained the following provision : The parties unite in a recommendation to Congress that legislation be forthwith enacted creating a separate anthracite coal commission with authority to investigate and report promptly on every phase of the industry and the parties hereby ask the President to request the enactment by Congress of the recommended legislation. The continuance of production after Aug. 31, 1923, shall be upon such terms as the parties may agree-upon in the light of the report of the Commission.

Jan 1, 1924

THE annual meeting of the Lake Superior Mining Institute was held on Sept. 7 and 8, Crystal Falls and Iron Mountain, Mich., being the principal centers of activity. Members of both institutes began assembling early, and by the evening of Sept. 6, some 60 had already arrived at Crystal Falls. The greater number arrived the following morning, however, and after the usual formalities of registration were attended to, the party were loaded into automobiles and set out on a tour of inspection of the mines near Iron River; some properties were passed through, and some were briefly visited to permit the inspection of any unusually interesting piece of equipment or detail of practice. The last stop of the morning was at the Caspian, Iron River, where the entire party was entertained at luncheon at the Caspian Club House. Both the food and the company were excellent, and as the weather was superlatively good (though the natives of the district modestly declared it was only ordinary autumn weather) the lunch was served on the lawn at the rear of the club, where the green turf, abundant flowers, and music by the band, added to the charm of good fellowship. The degree to which mining men have become addicted to golf was indicated by the large number of plus fours in evidence, whose wearers appeared just before lunch and disappeared immediately afterward.

Jan 1, 1928

By A. L. Blomfield

THE Golden Cycle Mining and Reduction Co. operates its custom mill at Colorado Springs on Cripple Creek ores exclusively. These ores are straight sulpho-tellurides, with practically no base metals such as Pb, Cu, Zn, As, or Sb. Upon entering the mill, the ore all passes through the sampler to storage bins, where beds of 5000 tons each are made to insure uniformity in roasting. CLASSIFICATION OF ORES For efficiency, it has been found advisable to separate the ores into two classes according to their line content. Other constituents have their effect, such as alumina and magnesia, but, speaking generally, these are roughly proportional to the line, which, as CaO, is used as the indicator. Class A contains not more than 2 per cent. CaO and comprises about 66 per cent. of the ore treated. Class B contains over 2 per cent. CaO, and comprises 34 per cent. of the ore treated. Typical analyses of both classes are as follows: Class A Class B Insol 56.70 75.90 Al203 2.30 3.40 Fe 3.26 3.48 CaO 1.57 5.12 S 1.79 1.80 Mg0 0.21 1.08 Ignition loss 3.20 6.50 99.03 97.28 The beds of each class of ore are made as large as possible with the available ore as it comes in, to avoid changing from one bed to the other any oftener than necessary. Each roaster will handle 50 percent. more of class A ore than of class B, with practically the same results. This necessitates changing the rate of feed for each new bed and tends toward a poor roast and loss of tonnage at each change.

Jan 8, 1918

By A. L. Blomfield, M. J. Trott

ThE Golden Cycle Mining and Reduction Co. operates its custom mill at Colorado Springs on Cripple Creek ores exclusively. These ores are straight sulfo-tellurides, with practically no base metals such as Pb, CU, Zn, As, or Sb. Upon entering the mill, the ore all passes through the sampler to storage bins, where beds of 5000 tons each are made to insure uniformity in roasting. Classification of ORes For efficiency, it has been found advisable to separate the ores into two classes according to their lime content. Other constituents have their effect, such as alumina and magnesia, but, speaking generally, these are roughly proportional to the lime, which, as CaO, is used as the indicator. Class A contains not more than 2 per cent. CaO and comprises about 66 per cent. of the ore treated. Class B contains over 2 per cent. CaO, and comprises 34 per cent. of the ore treated. Typical analyses of both classes are as follows: Class A a B Insol.......................... 86.70 75.90 Al2O3........................:.. 2.30 3.40 Fe.............................. 3.26 3.48 CaO............................. 1.57 5.12 S............................... 1.79 1.80 MgO........................... 0.21 1.08 Ignition loss..................... 3.20 6.50 99.03 97.28 The beds of each class of ore are made as large as possible with the available ore as it comes in, to avoid changing from one bed to the other any oftener than necessary. Each roaster will handle 50 per cent. more of class A ore than of class B, with practically the same results. This necessitates changing the rate of feed for each new bed and tends toward a poor roast and loss of tonnage at each change.

Jan 1, 1919

By Yu A. Chernegov

Building up the USSR's economic strength was the result of all the achievements and successes of our economy. The Soviet Union was the first to begin planned guidance of the economy. The mining industry of the USSR, which holds the first place in the world output of mining production, has always been considered as the main raw materials basis of the country's economy. High and stable development rates are a feature of planned economic management, based on the social ownership of the means of production. During the past ten years from 1965 to 1875 the national income used for consumption and accumulation increased practically by 1.9 times. There has been no inflation, no unemployment in the Soviet Union for about forty years already. High and stable growth rates of the production of mining industries and that of the branches, which are their direct consumers are characterized by the data in table I. The achievements and successes of the economy's development are to a great extent determined by the three planning components, which are as follows:

Jan 1, 1977

By Philip B. Bucky

WITH the exhaustion of the sections of iron ore bodies amenable to opencut mining the iron ore miners raise the question: "How can we mine the extensions of these ore bodies in depth with the same costs as obtained in opencut work?" This question brings to the fore the relationship between mineral exploration and research on mining procedures. The iron miners must either find new de? posits amenable to their known methods of mining or develop new mining methods for deep deposits. It is understood that the oil companies will spend $30,000,000 next year in the search for new oil fields. How much the metal mining companies will spend in the search for new ore bodies is unknown, but without doubt the amount will run into several millions of dollars. If the mining companies that concern themselves with metals, nonmetallics, and fuels will set aside a substantial sum for fundamental and applied research in mining methods, they can not only lower their costs but increase their reserves thereby. Any increases in mining efficiency automatically result in increased ore reserves at no cost.

Jan 1, 1947

By John V. Hamme

ONE of Tungsten Mining Corp.'s Vance County, N. C., mill near Henderson was the installation of a new crushing plant with a capacity of 45 to 50 tph. During 1953 the milling rate was jumped from 650 tons to 800 tpd simply by expanding existing facilities, eliminating bottlenecks, and making changes in the existing and new circuits. Previous expansions in 1951 and 1952 raised mill capacity from 300 tons to 650 tpd. In its latest move, Tungsten Mining decided that expansion of existing facilities would be more economical than building that normal production was uninterrupted. For the engineering and design of the new crushing plant and mill expansion the services of the Southwestern Engineering Co., Los Angeles, were obtained. The Southeastern Construction Co., Charlotte, N. C., carried out construction, alterations to existing facilities, and the installation of equipment

Jan 10, 1954

By L. E. Young

MUCH has been said and written on this subject and probably little new can be said. However, the point of view of the operating company changes from time to time, and more stress may be laid upon a subject today than was done some years ago, and it is with this changing point of view that the following observations are presented: The writer wishes to limit the discussion to views of a company mining bituminous coal, particularly to what the production department expects of the college grad¬uate. In an editorial in MINING AND METALLURGY for February, 1929, entitled "Is. Mining Engineering Passing?" it is stated that: It is not by accident that mining engineering courses have been general rather than special and form even today the only general engineering courses widely offered and followed by engineering students.'* * * even in this age of specialization, the mining engineers remain a body characterized particularly by broad knowledge.

Jan 1, 1929

By Frank L. Hess

BERYLLIUM is demanding more of the limelight, and the output of beryllium copper (containing 2% to~ 3 per cent of beryllium) seems to have grown 60 per cent above that of 1936, which was double that of 1935. There is increasing interest in beryllium-aluminum alloys and small quantities are being marketed at $50 per lb. for the contained beryllium. Other alloys also can be produced. Further price decreases for beryllium copper (now $23 per lb. for the contained beryllium) seem , possible and desirable. No difficulty has been experienced in obtaining beryl and a 'reserve stock has been built up. One supplier heretofore found reliable has offered to furnish 200 tons per month. Supplies during 1937 have come from the Black Hills in South Dakota, Colorado. India, and South America

Jan 1, 1938

By Arthur C. Spencer

(Glen Summit Meeting, June, 1911.) THREE great deposits of iron-ore, in Camaguey and Oriente Provinces, Cuba, are well known to me through careful field-examinations executed in the years 1901 and 1907. In 1901 I visited the Cubitas iron-ore district, which lies about 12 miles distant from the city of Camaguey in a northerly direction, and the Mayari district, which includes the Sierra Nipe, lying opposite Nipe bay on the north side of Oriente Province. In 1907 I again visited the Cubitas district, and also made a sojourn of several days in the Moa district, where the extensive deposits of iron-ore were observed and studied. The observations of 1901 were made under the auspices of the then Military Governor of Cuba; Gen. Leonard Wood, and my conclusions concerning the value of these deposits were incorporated in a report.1 The examination of certain denouncements of iron-ore in the Moa district in 1907 was made in behalf of iron-masters operating in the United States, to whom I reported the existence of large amounts of easily-workable limonitic iron-ore, properly designated " brown iron-ore " in the terminology now current among iron-ore producers in the United States. In 1908 I published a paper entitled Three Deposits of Iron Ore in Cuba, outlining the occurrence and origin of the surficial ores existing in the Cubitas, Mayari, and Moa districts.2 . 1 A Geological Reconnoissance of Cuba, by C. Willard Hayes, T. Wayland Vaughan and Arthur C. Spencer, printed as a part of the report of the Military Governor of Cuba for the year 1901, vol. i. 2 Bulletin No. 390, U. S. Geological Survey, pp. 318 to 329 (1908).

Mar 1, 1911

By L. Thomassen, N. Spooner, J. M. Thomas

NI-CR and some Ni-Cr-Fc alloys, when used as electrical resistance heating elements in reducing atmospheres, at times suffer rapid breakdowns due to so-called "green rot." These reducing atmospheres are most frequently used in bright annealing and heat-treating furnaces which are kept for long periods of time at 1500' to 1800°F. The green rot is a preferential oxidation of the chromium in the alloy to such an extent that the remaining metal frequently becomes ferromagnetic. The Curie point (magnetic transition point) at room temperature for a pure Ni-Cr alloy is known to be at about 7 pct Cr.¹ This represents a severe loss in chromium for one popular grade of resistance alloy, which is nominally 80 pct Ni-20 pct Cr. The formation of oxides along the grain boundaries makes the ribbon brittle and gives the fracture a green, earthy appearance—hence the name. The authors have studied this phenomenon, simulating the industrial conditions by heating resistance ribbons in various reducing atmospheres, such as moist hydrogen or the atmosphere specified in the ASTM test.² This atmosphere contains 16 pct H2, 10 pct CO, 4 pct C02, 1 pct CH1, 1.5 to 2.5 pct H2O, balance N2. Little success was had in producing severe corrosion with the commercial 80 pct Ni-20 pct Cr alloys. It had been noticed, however, that 90 pct Ni-10 pct Cr alloy wires deteriorated very rapidly when placed in the bottom of narrow thermocouple protection tubes. The bottoms of the tubes with the wires were heated in air. This took place both in porcelain tubes and in Inconel* tubes either with the cold end open or loosely stoppered with asbestos. On examination the wires showed microstructures which would be classified as green-rot corrosion. Subsequent investigations with various alloy wires confirmed the observation that corrosion occurred in some wires, including 80 pct Ni-20 pct Cr alloys, much more rapidly in such tubes than had occurred previously in test atmospheres mentioned above. When 90 pct Ni-10 pct Cr alloys are oxidized with an abundant air supply, the oxide coat consists of both nickel and chromium oxides. In this case thermodynamic equilibrium between the oxides is not established. However, when oxidized 90 pct Ni-10 pct Cr alloy specimens were heated to 1500" to 1800°F inside small diameter tubes, the oxide coat transformed to a bright metallic outer layer of nickel or nickel-rich alloy, beneath which appeared a green oxide, followed by intergranularly attacked metal. The obvious explanation is that in the narrow tubes, thermodynamic equilibrium is being established according to the equation NiO + Cr (in alloy) ? Ni + Cr2O3 This reaction is favored due to the fact that the oxygen pressure over nickel oxide is more than 10"' times the oxygen pressure over the green chromium oxide. The initial oxygen in the tubes is depleted very rapidly by oxidation of the wire and of the tube, if it is metallic. A confirmation of the occurrence of the reaction, reduction of NiO by the chromium in the alloy, was obtained by putting oxidized nickel foil into an evacuated quartz tube along with a piece of bright 90 pct Ni-10 pct Cr alloy ribbon, and heating the tube at 1820°F for a number of hours. The nickel oxide on the foil was completely reduced to pure nickel, leaving a bright foil. The 90 pct Ni-10 pct Cr alloy became strongly magnetic and showed the typical green-rot structure. Weights of the samples before and after testing showed the weight loss of the foil to approximately equal the weight gain of the ribbon. Evidently the bottom of long, narrow protection tubes, stoppered or not, may under certain conditions act just as the sealed quartz tubes in respect to being a confined space in which oxygen is not freely replenished. This condition of oxygen depletion can be prevented by introducing a small amount of air into the bottom of the tube. Many conditions becloud the green-rot phenomenon, such as carburization, sulphidization, and the presence of other corrosive agents. However, these experiments have shown that the basic reaction is a case of internal oxidation which can occur simply by adjusting the oxygen pressure to a low enough level so that the atmosphere will leave the nickel intact and oxidize the chromium. The action of the other agents in commercial atmospheres can then be taken up as individual cases. From these and numerous other tests completed to date or still in progress, it is believed that a more critical evaluation of electrical resistance alloys for their resistance to green-rot corrosion can be made. A much better understanding of the mechanism for this type of corrosion should also result. A more complete report on these experiments will be published later. In the May 1953 issue: TP 35213 Discussion: Solubility of Carbon and Oxygen in Molybdenum by W. E. Few and G. K. Manning, discussion by N. A. Gokcen: p. 747, first column, the fifth, sixth, and seventh lines should be the first, second, and third lines, followed by the present first, second, third, fourth, eighth, ninth, and tenth lines.

Jan 1, 1954

By P. D. Rao, H. B. Charmbury, D. R. Mitchell

As a result of a changing market pattern for anthracite, there is now an increasing demand for steam size and a decreasing demand for domestic sizes. To help the producer meet this new demand, the authors present the technical aspects of the problem of crushing domestic sizes to steam fineness and size. The market pattern for anthracite coal has changed considerably in recent years. The demand for domestic sizes has been gradually decreasing and the demand for the steam sizes has been increasing. The companies however aim for a maximum production of domestic sizes, since these sizes command premium prices. To meet the market demands, particularly in certain periods of the year, further size reduction of the coarse clean coal is necessary. The present practice of multistage crushing in toothed rolls leads to complicated flow arrangements and is high in cost. Data presented herein indicate that crushers with high reduction ratios could be used with a resulting simplification of crushing flows and an appreciable reduction of capital and operating costs. The different types of crushing equipment investigated included the rotary-type breaker, the jaw crusher, the impactor-type crusher, and the Aerofall mill. CURRENT PRACTICE The standard sizes of anthracite are presented in Table I and market specifications require that any given size be maintained with only a limited amount of oversize and undersize material. The 1958 prices of the various sizes also are presented, so it may be seen that size reduction is only performed when dictated by market demands. At the present time the general practice of crushing anthracite consists of removing the top size and crushing it in a toothed double roll crusher to the next largest size. Consequently, to reduce the domestic egg, stove, and nut sizes to steam sizes of pea, buck, rice, and barley, the original material must be screened to produce the three top sizes and each size must be crushed in three separate rolls to the next largest size. Each crushed product must then be rescreened to remove the oversize for re crush ing. Thus a typical operation would consist of scalping the egg size from a mixture, crushing it to stove size, and rescreening the product. This same cycle would be repeated for the stove and nut sizes requiring three screens and three crushers as well as conveying equipment to handle the crushed products. This results in an expensive series of operations to make a product which sells for a lower price. If the three top sizes are crushed in one operation to the smaller sizes then the yield of steam sizes is low and the production of Nos. 4 and 5 sizes is large. These sizes sell for lower prices than the steam sizes. A typical operation is presented in Fig. 1. From the figure it may be seen that the original cleaned anthracite contains 67.4 pet domestic sizes, 26.4 pct steam sizes, and 6.2 pct fines. After multistage crushing of the domestic to steam sizes the composition of the product is 0.6 pct domestic sizes, 89.6 pct steam sizes, and 9.8 pct fines. From a technical standpoint these results are reasonable but the handling and crushing costs are

Jan 1, 1961

By Joseph W. Richards

ALTHOUGH bad grammar, the above query is probably, at the present moment, good sense. Why was the Institute started and why does it continue to exist? The small group of men who worked out the original idea felt keenly the necessity of mining engineers and metallurgists getting together in order to discuss their professional problems. That necessity still exists but it does not strike the present generation of engineers so keenly because they have always had the Institute: they do not know what it is to be without it. The Institute is a great graduate school of mining and metallurgy. All of its members who have something to say worth saying are the teachers; all the rest may be learners or critics. No university or technical school can match the experience and information which the authors of its papers possess, no institution of learning has a body of potential listeners so extensive and so vitally interested.

Jan 1, 1921

By H. H. Alexander

In the early part of the last century textile fabric was used for the filtration of products of combustion and lampblack was obtained by passing smoke through a series of canvas bags. Natural draft was used to draw and force the smoke through the bags. About 1850 bag filtration was used for collecting zinc oxide. Around 1876 it was introduced for collecting the fume from lead-ore hearth smelting in Missouri. Shortly afterward it was used, first at Portland, Me., and later at Canon City, Colo., for the collection and production of zinc-lead pigment in treating mixed zinc-lead sulphides. In 1890 the Globe Smelting & Refining Co., at Denver, Colo., installed a bag house containing 1,458 bags for the recovery of fume from silver-lead blast furnaces. This installation was too small to handle all of the gases and was increased to approximately 2,300 bags. In 1900 the number of bags was again increased, making a total of approximately 2,800. The usual difficulties incident to new installations were encountered, but they were gradually overcome and the bag house became accepted as standard practice for this class of smelting, As all of the bag houses built since have followed the general lines of the Globe installation, a short description may be of interest. The general construction of the Globe bag house is shown in Figs. 1, 2, and 3. The building is 149 ft. 8 in. long by 67 ft. 4 in. wide and 40 ft. 2 in. high from the basement floor to the eaves of the roof, having brick walls 26 in. thick from the foundation up to the thimble floor, from there an 18-in. wall for 16 ft. and a 13-in. wall from this point to the top, a distance of 14 ft. 2 in. Additional stiffening is given to the walls above the basement by pilasters located every 16 ft. The end-wall construction is similar to that of the side walls with the exception of the spacing of the pilasters, which is somewhat greater. The roof is made of corrugated iron laid on 1-in. boards and supported by a timber frame work spaced 16 ft. apart resting on the basement partition walls. On top is a louver running the

Jan 1, 1915

By H. H. Alexander

IN the early part of the last century textile fabric was used for the filtration of products of combustion and lampblack was obtained by passing smoke through a series of canvas bags. Natural draft was, used to draw and force the smoke through the bags. About 1850 bag filtration was used for collecting zinc oxide. Around 1876 it was introduced for collecting the fume from lead-ore hearth smelting in. Missouri. Shortly afterward it was used, first at Portland, Me., and later at Canon City, Colo., for the collection and production of zinc-lead pigment in treating mixed zinc-lead sulphides. In 1890 the Globe Smelting & Refining Co., at Denver, Colo., installed a bag house containing 1,458 bags for the recovery of fume from silver-lead blast furnaces. This installation was too small to handle all of the gases and was increased to approximately 2,300 bags. . In 1900 the number of bags was again increased, making a total of approximately 2,800: The usual difficulties incident to new installations were encountered, but they were gradually overcome and the bag house became accepted as standard practice for this class of smelting. As all of the bag houses built since have followed the general lines of the Globe installation, a short description may be of interest. The general construction of the Globe bag house is shown in Figs. 1, 2, and 3. The building is 149 ft. 8 in. long by 67 ft. 4 in. wide and 40 ft. 2 in. high from the basement floor to the eaves of the roof, having brick walls 26 in. thick from the foundation up to the thimble floor, from there an 18-in. wall for 16 ft. and a 13-in. wall from this point to the top, a distance of 14 ft. 2 in. Additional stiffening is given to the walls above the basement by pilasters located every 16 ft. The end-wall construction is similar to that of the side walls with the exception of the spacing of the pilasters, which is somewhat greater. The roof is made of corrugated iron laid on 1-in. boards and supported by a timber frame work spaced 16 ft. apart resting on the basement partition walls. On top is a louver running the

Jan 8, 1914

By AIME AIME

BY COMBINING the sessions on reduction and refining of copper, lead and zinc it was possible to devote an entire day to nonferrous metallurgy. Four interesting papers were presented at the morning session and four more in the afternoon. In the discussion of papers on copper, F. R. Pyne acted as chairman, with H. M. Shepard as vice-chairman, whereas for those on lead and zinc, F. F. Colcord acted as chairman, with C. R. Hayward as vice-chairman. The paper by P. D. I. Honeyman on the smelting of raw concentrates in the reverberatory furnace was presented by Mr. Pyne and discussed by Messrs. Mazany and Hayward. The interesting paper by E. S. Bardwell, com- paring the use of various fuels in copper-refining furnaces at Great Fails, Mont., was presented by Mr. Shepard and discussed by Messrs. Boggs, Gronningsater and Hayward. That by R. G. Knickerhocker, describing the stationary basic copper converter at Messina, Transvaal, was presented by Mr. Pyne, together with a written discussion by c. R. Kuzell, of the United Verde Copper co. It was an interesting illustration of how well-known processes may sometimes be modified to fit into unusual conditions.

Jan 1, 1932

By R. D. Nelson, S. D. Dahlgren

The conditions of temperature, strain rate, and total strain favoring deformation by grain boundary sliding, slip, or deformation with concurrent recrystallization were evaluated for alpha plutonium. Grain boundary sliding and slip were studied by examining structures formed on polished surfaces with 4.5 pct compressive deformation. The conditions required for recrystallization were determined from compressive deformation us time curves. At 110" C and at a strain rate of 10&apos;per min, deformation was almost exclusively by grain boundary sliding whereas slip was the predominant deformation mode at -10°C and lo-&apos; per min. Defarmation at intermediate tenzperatures and strain rates produced structures showing mixtures of grain boundary sliding and slip. Recrystallization occurred concurrently with deformation only after a critical strain was reached. About 14, 6, and 3 pct strain was required at 105", llO°, and lZO°C, respectively, before recrystallization started, irrespective of the strain rate in the range of lo-&apos;1 to 10&apos;4 per nzin. L HE temperature and strain-rate dependency of the modes of plastic deformation were evaluated for high-purity as-cast alpha plutonium. The techniques used to study slip and grain boundary sliding were similar to those employed previously for alpha plutonium by Bronisz and Gorum,&apos; and spriet.&apos; Recrystallization was investigated using the methods reported by Nelson.3 Bronisz and Gorum&apos; found that slip occurred on more than one slip system at room temperature, and suggested that grain boundary sliding also contributed to the deformation. spriet2 found that deformation was predominantly by slip at room temperature, and observed one to three orientations of slip traces in individual grains. In addition, he deformed polished samples at 10O° C, but concluded that the deformation character of alpha plutonium at 100° C and at room temperature were not essentially different. Several investigators reported that twinning was only occasionally observed.1&apos;2&apos;4 Nelson3 recently found in creep tests that high-purity alpha plutonium would recrystallize concurrently with compressive deformation at temperatures between 25" and 115°C. EXPERIMENTAL PROCEDURE Electrorefined plutonium having less than 300 ppm total impurities was received from Los Alamos Scientific Laboratory in the form of +-in. diarn cast rods. Major impurities were americium, <I00 ppm, and tungsten, (60 ppm. Less than 25 ppm each of other impurities were present. The rods were cut into right half-cylinders 0.35 in. long and 0.25 in. in diam, and the flat faces along the cylinder axes were metal-lographically polished. To avoid loss of the metallo-graphic polish by oxidation, the polished samples were deformed in a silicone fluid heat treating medium contained in a chamber evacuated to a pressure of lo-&apos; torr. Deadweight loading was used to compress the samples between 4.5 and 20 pct at strain rates between 10"4 and lo- &apos; min-&apos;. Strain rates were determined by dividing the total deformation by the elapsed time of the test, even though the strain rate was not constant during deformation. Curves of strain vs time for samples deformed with a constant compressive stress3 show that the strain rate changes by less than a factor of four during the testing of a given sample, which is small compared to the three orders of magnitude change in strain rate investigated. Two samples were loaded into an ordinary metallographic mounting mold and impacted by striking the mold piston with one blow of a 2-lb hammer. Deformation temperatures for the two impact samples were 25" and 90°C. The samples, following deformation, were washed in carbon tetrachloride and their polished and deformed surfaces were immediately inspected metallographi-cally. Subsequently, the deformation structures were replicated with acetate replicating tape for later electron microscope examination, and the samples were then repolished and etched to reveal the microstruc-tures of the deformed metal. Second-stage carbon replicas were prepared from decontaminated acetate replicas using the procedure developed by Miller, Bierlein, and astel.&apos; Additional samples, which were 0.35 in. long by 0.25 in. in diam, were used to obtain constant load deformation vs time curves. These samples were deformed 10 to 20 pct with loads of 15 and 20,000 psi at 120°C; 30, 45, and 55,000 psi at 110°C; and 20 and 30,000 psi at 105°C. Samples were polished and etched to determine whether or not recrystallization or twinning had occurred during deformation. RESULTS AND DISCUSSION The experiments showed that alpha plutonium deforms by grain boundary sliding, slip, and deformation with concurrent recrystallization. Deformation by twinning was insignificant. Metallographic examination of polished and deformed surfaces revealed grain boundary sliding and slip. The start of recrystallization was ascertained from constant load deformation vs time curves. Deformed surface structures of samples compressed 4.5 pct under four different conditions of temperature and strain rate, Fig. 1, show how the deformation mode changes from predominantly grain boundary sliding to predominantly slip with increasing strain rate and decreasing temperature. Deformation at 110°C and 10" 4 min-&apos;, Fig. l(a), was predominantly by grain boundary sliding. Only a few slip traces can be seen in Fig. l(a).

Jan 1, 1969

By Herbert Hoover

I HAVE been greatly honored as your unanimous choice for President of this. Institute, with which I have been associated during my entire professional life. It is customary for your new President, on these occasions, to make some observation on matters of general interest from the engineer&apos;s standpoint. The profession of engineering in the United States comprises not alone scientific advisers on industry but, in great majority, is comprised of the men in administrative positions. In such positions, they stand midway between capital and labor. The character of your training and experience leads you to exact and quantitative thought. This basis of training in a great group of Americans furnished a wonderful&apos; recruiting ground for service in these last years of tribulation. Many thousands of engineers were called into the army, the navy, and civilian service for the Government. Thousands of high offices were discharged by them with credit to the profession and the nation. We have in. this country, probably, one hundred thousand professional engineers. The events of the past few years have greatly stirred their interest in national problems.&apos; This has taken practical. form in the maintenance of joint committees for discussion of these problems and support to a free advisory bureau in ,Washington. The engineers want nothing for themselves from Congress.. They want efficiency in government, and you contribute to the maintenance of this bureau out of sheer idealism. This organization for consideration of national problems has had many subjects before it, and I propose to touch on some of them this evening.

Jan 1, 1920

By C. Norman Cochran

The pllnse diagvam for the NaF-AlF3 system was used to calcutate an ionic model for the NaF-AlF3 system. Assuming an ideal solution,a series of simultaneous equations expressing equilibria be-tween solid and liquid phases at the euleclic, perilec-tic, and melting points were solved for the activities of the ionic species, the dissociation constants, and the entropies and heats of fusion. The calculations suggest the existence of A13F1415 ions in addition to the F-1+AlF6-3 , and AlF4-4 ions previously proposed by others. The calculaled valnes give better agreement with vapor pressures than the previous model without Al3Fl14-5. Additional possible vefinements of the model are proposed. CRYOSCOPIC1 investigations and density data2 for the NaF-A1F3 system have previously been used to study the dissociation mechanism of Na3A1F6 and to derive equilibrium constants for its dissociation to NaF and NaAlF,. Depending primarily on the heat of fusion assumed for cryolite, the dissociation constants ranged between 0.02 and 0.18 from cryoscopic studies, and from 0.09 at 1273°K to 0.16 at 1363°K from density data. In most cases the values were unable to reproduce satisfactorily the experimental liquidus lines very far on the A1F3 side of the Na3A1Fe composition. This suggested the existence of at least one other ionized compound in the melt besides NaA1F4 in the Na3A1F6-A1F3 side of the system. This is assumed to be liquid Na&13F14 (chiolite), which is already established as a stable solid in phase studies of this system. MODEL FOR THE MELT The melt is assumed to be an ideal solution with ion activities equal to anion fractions. The only cation in the model is sodium so that Temkin and simple anionic activities are identical. Although the compounds are completely ionized to Na&apos; and the respective anion in the melt, molecular rather than ionic notation is used throughout this work. The Na3A1Fe is assumed to dissociate to NaA1F4 and NaF as in the former model, and Na&13F14 to dissociate to Na3A1Fe and NaA1F4. Other valid dissociation equilibria can be written involving these four compounds, but all of these can be obtained by combinations of the two described dissociation reactions and, thus, are automatically considered in these calculations. The model allows for no free AlF3 so that compositions for NAIF3 > 0.5 (mole fraction A1F3 on the NaF-A1F3 basis) cannot be treated. The question of the existence of free AlF3 in the melt will be discussed again later. The constants in the model were evaluated from points along the entire known liquidus line of the NaF-A1F3 system. Previous work employed only the liquidus line or densi- ties near the Na3A1F, composition. The liquidus line compositions used in the solution of the model are from unpublished work by Mr. P. A. Foster, Jr., for compositions between the Na3A1F6 melting point and the Na&13F14-A1F3 eutectic, and from the published works of Grjotheim,1 Phillips,3 and Foster4 for the remainder of the system. The relationships used in solving for the desired dissociation constants and heats and entropies of fusion are listed in Table I, and the points along the liquidus line at which each apply are indicated to the right of the relationships. The mole fractions of each of the separate species in the melt are symbolized by N. Relationships [I] and [2] are the respective dissocia-ation constants, Kl and K2, of Na3AIF6 and Na5A13F14 for this model. For simplicity, these constants will be assumed to be independent of temperature. Relationship [3] follows from the assumption of the ideal solution. The expression relating the values of N to the experimental values of NAIf3, is given in Relationship (41. Relationships [5], [6], and [7] each state the equilibrium between a compound in the melt and its pure solid phase for the portion of the liquidus lines where it precipitates. The heats of melting, AH,, and entropies of melting, AS,, used in [5], [6], and [7] are assumed to be independent of temperature. The compositions and temperatures of all five invariant points (two melting points, two eutectics, and one peritectic) along the liquidus lines from NAIF3 = 0 to NAIF3 = 0.5 were employed in the solution. The eutectic and peritectic compositions were particularly useful because each of these is involved in one more equation than other points along the liquidus lines and thus reduces the number of points required to solve for the constants. Also, their use assures that the inflection points in the derived liquidus line will correspond exactly with those on the experimental liquidus line. The total number of equations is 5k1 — 1, where n is the number of experimental composition points used. The number of unknowns is 4n + 5 (4n- 3 values of N, 3 values each of AH, and AS,, and 2 values of K). Thus, six points must be used in the solution to obtain an equal number of equations and unknowns. The one additional required experimental composition was taken on the liquidus line between the Na3A1Fe melting point and the Na3A1F6-Na5A13F14 peritectic. Previous work indicated this was a difficult portion of the curve to fit. The temperature used for the point was 1161°K, the same as for the NaF-Na3A1Fe eutectic. This choice of temperature gave two points with identical NNa3AIF6 values which simplifies the algebraic solution. The second point at this temperature is denoted 1161°&apos;K. PROCEDURE FOR SOLUTION OF EQUATIONS Values were assumed for NNa,AIF and NNaF at the NaF-Na3A1F6 eutectic at 1161°k. By an iterative procedure, the corresponding values for NNa5A13F14 and NNaAlF4 at 1161°K were determined from 131 and 141. A value was assumed for NNaAlF4 at 1161°&apos;K and

Jan 1, 1968