Search Documents

By Walter D. Holland

This study was undertaken to determine miners' breathing zone concentrations of diesel exhaust components, to investigate any relationships between these concentrations and vehicle type, the presence of emission controls, vehicle usage, and ventilation conditions, and to make recommendations for monitoring and ventilation requirements. Twenty-four mines including two con l mines were surveyed. Sampling was done for CON, NON, SOx, PNA, aldehydes, and particulates. hi most mines, concentrations of at least one contaminant exceeded one half the standard or TLV. The concentrations of gases arc probably sufficiently reduced by a minimum air velocity of 50 fpm. A sufficient reduction of particulate concentrations may require as high as 400 fpm air velocity. Vehicle age, type, or usage appear to have little or no effect on contaminant concentrations. PNA levels were below detection limits in all but a very few samples. Minimum requirements for routine monitoring should include formaldehyde, COx, NO2. It is further recommended that better definition of the minimum ventilation requirement be obtained.

Jan 1, 1978

By Michael Ostrowski

While the words “explosives” and “blasting” cause insurers to become apprehensive, skilled contractors using modern techniques under controlled conditions rarely cause serious damage or injury. However, blasting operations frequently result in complaints and, consequently, insurance claims. The purpose of this bulletin is to inform construction project participants of some of the measures which may be taken to reduce losses arising from blasting operations.

Jan 1, 2003

By R. M. Kuralt

CONCESSION from the Chilean government granting the company use of the Rio Salado water stipulates that a minimum of 35,000 metric tons of such salty water must be diverted from the Salado daily, and be disposed of in a manner not to contaminate the Rio Loa to the east of its confluence with the Rio San Salvador at Chacance, Fig. 1. Consequently, the selection of a suitable site for the sulphide plant tailing disposal had the additional problem of the disposal of excess brackish waters. Studies of the terrain in the area directly to the south of the plant indicated that construction of tailing ponds would be costly, and generally unsatisfactory due to excessive slope of the ground, lack of flanking hills, danger of raising the groundwater level thus causing springs along the Antofagasta-Bolivia railroad; and the possibility of creating a dust nuisance at the plant site or at Calama due to blowing sands. Further to the southwest the San Salvador river canyon offered some possibilities and surveys were made at sites A to D, inclusive, Fig. 1. Here again costly dams would have been necessary to impound the tremendous quantity of tailing produced by the new plant, and provision would have to be made to handle a considerable flow of water through the disposal area to the west of the Rio Opache. Additional surveys were made in the area to the southeast of the plant which brought to light the existence of a natural basin of about 14 1/2 square miles, flanked by low-lying hills, and requiring only the most rudimentary dams to close the outlets at the western end. It has been estimated that the Salar de Talabre, as this basin is called, has the ultimate storage capacity of 1 billion tons of tailing with dam heights of only 60 ft. Pipe Line Layout After the decision had been reached to use the Salar de Talabre for the main disposal area various methods were considered for transporting the tailing from the 300 ft diam thickeners to the disposal site, 17.7 miles away. The first plan was to construct a. concrete launder on a 11 pct grade but a survey of this grade line indicated it would not lead directly into the Salar but would terminate somewhat to the north, and from that point on the slope would be considerably less than 1 pct along a natural watercourse. A slope of 2 pct or even 2 ¼ pct in such a rough watercourse or ditch is the ideal, judging from the success of operations at Cananea. Since a simple ditch is the most economical vehicle for the transportation of tailing, it was decided to use one with a 2 ¼ pct grade for as much of the distance as was possible with the existing terrain and to construct a concrete headbox, or forebay, at the terminus of the ditch to supply a steel pipe line leading the rest of the way into the Salar. Referring to the maps of the Chuquicamata area outlining the tailing disposal system, Figs. 1 and 2, one can trace the flow of the tailing from the thickeners to the Salar as follows: The 8-in. spigot pipes from the thickeners (1) discharge into a concrete sump feeding a concrete launder with a 2 pct slope. The launder carries the tailing into a concrete junction box (2) located south of the sulphide plant. The purpose of the junction box is to provide emergency facilities for diverting the tailing flow from the main disposal area to the emergency area. It also provides a junction point for the launder from the sulphide plant's future east extension. The box is fitted with a pair of radial gates controlling flow into the main tailing ditch (6) or the emergency ditch (3) which terminates on the pampa. All ditches are of the same cross section, namely 4 ft wide at the bottom with 1 : 1 side slopes and with a minimum depth of 21/2 ft. Where the nature of the ground demands it, the ditches are lined with stone rubble. The overflow from the plant's 10 million gal reservoir (4) is led into the main tailing ditch by way of a spillway ditch (5). The main ditch terminates in a trashscreen fitted, concrete forebay (7) which serves as a headbox for a 24 in. O.D. x 3/8 in. wall, Dresser coupled, steel pipe (10) and a 12 in. x 8-gage spiral welded, wedge-lock coupled, steel pipe (8). The forebay is fitted with two compartments, one for each pipe, and flow into each is controlled by radial gates. Each compartment is fitted with a 6-in. drain pipe controlled by a rubber pinch valve. To protect the forebay from the abrasive effects of the tailing, the sides of the compartments will be lined with old

Jan 1, 1952

By Robert G. Gibson, Joel D. Gibbons

Measurements and analyses were conducted of whole-body vibration aboard seven commercially available passenger and/or recreational vehicles: sedan; sport-utility vehicle (SUV); pickup truck; moving truck; motorcycle; all-terrain vehicle (ATV); and boat. The purpose of the testing was to measure and assess whole-body vibration exposure in a range of typical vehicle environments in order to gain understanding of typical exposure levels characteristic of activities of daily living. Vehicle models tested (and model year) were: Ford Taurus (1995); Jeep Cherokee Sport (2000); Toyota Tundra SR5 (2002); Ford F-350 (1997); Harley-Davidson Electra Glide Classic (2004); Yamaha Kodiak 400 4x4; and Steiger Craft Model 21 Montauk. All vehicles were tested with their standard factory-installed seats and were operated under a range of normal operating conditions and speeds typical of intended vehicle use. Methods The measurement, processing, analysis, and exposure assessment methods follow the guidance of generally accepted, national and international consensus standards relevant to the evaluation of whole-body vibration, including ISO 2631-1 [1] and ANSI S3.18 [2]. Seats were instrumented with low-mass triaxial accelerometers mounted in seat pads. Accelerometers used in the test are specified to have flat frequency response over the frequency range of 0.5 to 80 Hz, and all accelerometers were recently calibrated traceable to the National Institute of Standards and Technology (NIST). Seat pads were installed following guidance in the relevant standards [1, 2], with sensitive axes of the accelerometers following the standard coordinate system with respect to the seated occupant. (The x-axis represents fore-aft motion; the y-axis represents side-to-side motion; and the z-axis represents vertical motion with respect to the occupant.) Vibration data processing and analysis, including filtering, sampling, frequency-weighting, averaging, summation, and determination of basic and additional metrics followed procedures in the relevant standards [1, 2]. Digitized time series data were acquired and stored using a PC-based data acquisition system. Whole-body vibration exposure analyses were conducted via post-processing. During data processing, recorded periods of seat acceleration that were identified and verified as resulting from occupant-induced motion rather than vehicle motion were excluded prior to exposure analysis. The basic evaluation metric for whole-body vibration is the frequency-weighted root-mean-square (r.m.s.) acceleration, aw. The primary additional evaluation metric is the fourth-power

Jan 6, 2006

By Donald O. Capstick

A mineral resource evaluation of the Coyote-Southeast RARE II area (No. 5033) was performed jointly by the U.S. Bureau of Mines and the U.S. Geological Survey in 1981 for the U.S. Forest Service RARE II program. Bureau of Mines personnel conducted a mineral resource inventory of the study area's mines, prospects, claims, and mineralized outcrops. The study area's boundaries encompass 51,700 acres on the east flank of the Sierra Nevada and are within Inyo National Forest southeast of the city of Bishop in east-central California. Cretaceous granite underlies most of the area; the remainder of the rocks are metasedimentary. At the contact of the two, tactites formed at many places where carbonate rocks were present; replacement processes produced local scheelite (calcium tungstate) occurrences.

Jan 1, 1983

By C. Patrick

Longwall face-to-face transfers can cost over $100 per minute in lost production potential and $100,000 for personnel and supplies. Such high cost makes extensive planning and control of the transfer process a critical necessity for the economic feasibility of longwall operations. This paper reports operations research techniques used for the analysis and modeling of longwall face-to-face transfers. Transfer data has been collected from companies who operate over 30% of the total U.S. longwall faces. Comprehensive sequence networks of existing longwall transfers were developed; simulation models of transfers under varying conditions were generated; and, the economics of general transfers and time-cost tradeoffs in the transfer procedure were investigated.

Jan 1, 1993

By K. H. McDaniel, D. M. Loring

The underground ventilation system at the Waste Isolation Pilot Plant provides unparalleled ability to ensure safety of the workers, public and environment. Although small spatially, it can vary the airflow from 66,000 acfm to 460,000 acfm. It can automatically incorporate HEPA filtration in the event of radioactive contamination. Remote-capable regulators individually control the four main splits, and can be adjusted from the surface if necessary. A ventilation remote monitoring and control system provides real-time information. Future areas of concern include DPM compliance, system psychrometry, logic-based-real-time mine ventilation simulation and automation using PLC technology. This paper discusses the evolution of this system.

Jan 1, 2002

The Ngakuru zeolites are located about 20 km south of Rotorua and comprise a number of deposits dispersed along several fault lines. Relatively recent volcanic activity (250,000 years ago) resulted in ash depositions that vary in depth and mineralogy. Subsequent variable thermal alteration intensities generated predominantly clinoptilolite and mordenite zeolites with a range of physical characteristics. Typically the zeolites have low density (650 kg/m3), have high liquid (60% of dry weight) and odour absorption characteristics, and a high affinity for soluble cations (CEC =: 100 meq/100 g). Traditional kitty litter and oil absorbency markets are being expanded. New opportunities in waste and potable water treatment, organic and synthetic slow release fertilisers, use as a light weight aggregate for speciality concretes, and pozzalome activity are currently being researched.

Jan 1, 2000

By Frank P. Frandina

The Heartland Corridor Clearance Improvement Project is part of a regional Public-Private initiative to allow double stack container trains a direct route from the Port of Norfolk through Virginia, West Virginia, Eastern Kentucky and into Central Ohio. The project involves clearance improvements to twenty-eight tunnels, twenty-one of which require structural modification. With construction of the first Package of tunnels just underway at press time, this paper summarizes the program implementation from design through the initial stages of construction.

Jan 1, 2008

Ceremonies for the induction of four mining industry pioneers into the National Mining Hall of Fame will be held Saturday, Sept. 22, 2007 at the Charles F. Barber Pavilion (Museum Convention Center) in Leadville, CO. The four inductees are James Harold Courtright (1908-1986), Dr. Howard L. Hartman (1924-2002), Charles Washington Merrill (1869-1956) and Kenyon E. Richard (1915-1993). The inductions will bring to 197 the number of mining “greats” whose engraved photographs and biographical sketches are installed in the National Mining Hall of Fame.

Jan 1, 2007

By M. Didyk

The final objective of a mine ventilation project is to find a way of supplying the working faces with the necessary quantity of air to dilute all the possible air contaminants to safe limits and to maintain the temperature, humidity and oxygen content within desirable limits. To accomplish the aforesaid, decisions have to be made at early stages of planning and design of a mining operation. That is, ventilation and mine planning are closely related and interdependent, and experience has proved that improvisation as related to mine environment is rarely optimal in ventilation engineering. Mine management should be concerned with two general aspects of ventilation problems. The first is related to the statuatory requirements which are usually the minimum standards that have to be maintained. During the last two decades, mining laws have become increasingly stringent and management of operating mines had to face the effects of these externalities. In some cases these required either a production rate reduction or additional mine development. The second aspect that management should not overlook is the technical and economical importance of mine ventilation on the overall mining cost. In coal mining it is necessary to move, on an average, five tons of air through the mine for each ton of coal produced. The power cost incurred is perhaps the single most important direct cost assigned to ventilation but it is not the only one. Other costs that should be considered include the supervisory labor cost, fan depreciation and maintenance, doors, stoppings and regulators construction cost and maintenance, the additional mine airways development and maintenance because of ventilation requirements. That is,

Jan 1, 1977

By G B. Arehart, J L. Mauk

Quartz veins from the Martha Hill epithermal gold-silver deposit, Waihi, commonly exhibit crustiform banded textures. Visual differences observed between bands are primarily the result of a 1 to 1500 ¦m variation in quartz grain size. Quartz band textures are dominated by anhedral interlocking quartz mosaics, commonly associated with minor adularia and sulphide phases; these textures are interpreted to be products of amorphous silica crystallisation. The occurrence of rhombic adularia suggests that prolonged boiling influenced parent fluids. In contrast, the presence of coarsely crystalline bands, made up of subhedral to euhedral quartz grains, infers primary crystal growth from solution; evidenced by the occurrence of growth-zoned quartz within these bands. There is a narrow range of 3.3ë in d18Oquartz between maximum and minimum isotopic values for the deposit. Significant overlap in d18Oquartz values are observed between the Martha and Welcome lodes. However, statistically significant and commonly systematic differences do occur between individual bands analysed in most samples. Temperature fluctuations may be the dominant factor responsible for observed inter-band variation.

Jan 1, 1995

By T. Yegulalp, R. Farrauto, A. Belova, M. Castaldi

Calcium oxide, with its ability to capture and store carbon dioxide, is emerging to become an important tool in carbon management. Calcium oxide can be used reversibly to capture carbon dioxide in situ and then be regenerated to produce a pure stream of carbon dioxide ready for sequestration; the Zero Emission Coal Alliance technology utilizes this property of calcium oxide to generate emissions-free electric power from coal. The reaction of calcium oxide with carbon dioxide resulting in thermodynamically stable carbonate is well understood; however, the efficiency of this reaction is limited by the diffusion of gases through bulk calcium oxide and through a layer of carbonate formed on the surface. In addition, the regeneration of calcium oxide is an endothermic reaction and is favored at high temperatures. The purpose of this paper is twofold: first, to address the diffusion limitation, a thin layer of calcium oxide, supported on a high surface area material, is studied thermogravimetrically to demonstrate the physical adsorption of carbon dioxide on calcium oxide. The adsorption is to take place at temperatures lower than required to form calcium carbonate.

Jan 1, 2007

By S. M. Marshall

The investigations recorded in this bulletin were conducted by the Pacific Coke & Coal Co. in cooperation with the United States Bureau of Mines and the University of Washington. They cover one phase of a comprehensive investigation to determine whether coals from an extensive, undeveloped area of Pierce County, Wash., can be used in the manufacture of coke for the iron blast furnace. The completed investigation had three parts: (1) A geological survey of the coal property, (2) washing and crushing tests of the coals, and (3) coking and by-product tests. The geological survey, which was not conducted in cooperation with the Bureau of Mines and the University of Washington, included systematic tracing of the coal beds by test holes throughout the property, except some portions covered by an impenetrable layer of glacial drift. By this means all of the beds were correlated, their thickness and general character were determined, and tonnage estimates were made. Only such parts of the survey results as are necessary to a full explanation of the investigations described herein are included in this bulletin.

Jan 1, 1931

By R J. In, C Moore, P J. Moffitt, T Hansen

Telfer Gold Mine combines a world-class gold and copper resource and longevity of operation as a major gold and copper producer. Telfer Gold Mine has undergone a series of transformations since mining commenced as a high-grade narrow-vein oxide open pit operation in 1977. In 1986, the open pit operation converted from a narrow-vein, high-grade operation, to a low-grade high-volume oxide mining operation utilising dump leach processing technology. Mechanised underground mining of the high-grade narrow-veins commenced in 1990. Total recovered gold production between 1977 to 1999 has totalled 5.7 million ounces. The Telfer Extension Project consists of two pre-feasibility studies, the Surface Extension Project (SEP) and the I-Series Project (ISP). The combined studies represent one of the more significant resource evaluations undertaken in the gold industry in recent times. Geological activities for the SEP pre-feasibility study have included the drill definition of a large low-grade resource within an area of 25 km2 . The surface drilling program has completed 15 000 metres of HQ3 diamond drilling and over 30 000 metres of RC between last quarter of 1998 and late-1999. The ISP pre-feasibility study is currently evaluating the resource potential of both a high-grade low-volume and a lower grade bulk mining scenario, 800 m to 1200 m below the surface of Main Dome. 15 000 metres of underground diamond drilling have been completed between last quarter of 1998 and August 1999 as part of this study. Systems and cultures have been developed to maximise safety, monitor the quality assurance/quality control (QA/QC) on all aspects of the operation, and minimise impact on the environment. All data are stored in database systems, specifically designed for Telfer operations. 3D geostatistical resource estimation using ordinary kriging has been carried out for over 220 geological domains within the 25 km3 of mineralised system. Non-linear geostatistical techniques are being investigated as part of the pre-feasibility study.

Jan 1, 2000

By G. W. Jones, R. E. Kennedy

"INTRODUCTION In the manufacture, storage, transportation, and use of combustible gases and vapors, explosion hazards, which at times may be present when air becomes mixed with the gases and vapors, become of primary importance. Such conditions are especially dangerous where large volumes of gaseous atmosphere are involved, because an explosion under such circumstances is capable of doing tremendous damage to both property and personnel.Because of its interest in safety in the mining and allied industries, the Federal Bureau of Mines has investigated, and published results dealing with, the explosibility of various types of combutible atmospheres. The explosion hazards of natural gases have received attention, and results giving the limits of inflammability and ignition temperatures in air have been determined and published. 4/ Other investigations have shown how explosions of natural gas-air mixtures may be prevented by the addition of nitrogen and carbon dioxide. 5/Because of the increased demand for crude oil for war purposes, the application of secondary-recovery methods of stimulating oil production have received considerable attention during the last few years. The process consists in the injection of natural gas into partly depleted oil wells to cause the oil in the sands to flow into producing wells and so increase the amount of recoverable oil. 6/"

Feb 1, 1945

To the members of The South African Institute of Mining and Metallurgy We have audited the annual financial statements of The South African Institute of Mining and Metallurgy set out on pages 357 to 366 for the year ended 30 June 2002. These financial statements are the responsibility of the Institute?s Council. Our responsibility is to express an opinion on these financial statements based on our audit. Scope We have conducted our audit in accordance with statements of South African Auditing Standards. Those standards require that we plan and perform the audit to obtain reasonable assurance that the financial statements are free of material misstatement. An audit includes: ?examining, on a test basis, evidence supporting the amounts and disclosures in the financial statements, ?assessing the accounting principles used and significant estimates made by management, and ?evaluating the overall financial statement presentation. Audit opinion In our opinion, the financial statements fairly present, in all material respects, the financial position of the Institute at 30 June 2002 and the results of its operations and cash flows for the year then ended in accordance with South African Statements of Generally Accepted Accounting Practice. Auditors 26 July 2002 Council?s approval of the annual financial statements The annual financial statements for the year ended 30 June 2002 set out on page 357 to 366 wereapproved by the Council on 26 July 2002 and are signed on its behalf by:

Jan 1, 2002

By Timothy Stark

Blasters are usually strictly liable for injury or damage caused by flyrock (trespassory invasion) and blast-induced vibrations (non-trespassory invasion). The application of strict liability to non-trespassory invasions has resulted in significant litigation that has hampered the use of blasting and the blasting industry. Stark (2002) proposes that blasters should not be held strictly liable for non-trespassory invasions but should be liable only if their conduct is proven to be negligent. This change in legal standard was proposed because improvements in blasting technology over the last thirty years allow blasting to be conducted without substantial risk of harm to property and thus the amount of harm imposed by a blast can be related to the level of care exercised by the blaster. It is anticipated that a negligence standard will reduce the amount of litigation because a plaintiff will have a greater burden to overcome. To facilitate the acceptance of a negligence standard by a court of law, this paper summarizes the standard of care using the 1977 Surface Mining Control and Reclamation Act, extensive U.S. Bureau of Mines research, and current blasting techniques, such as blasting mats. It is important for the blasting industry to promulgate a standard of care so a judge can feel confident that blasting can be routinely and systematically controlled and if the legal standard is changed from strict liability to negligence a subsequent judge or jury will be able to evaluate the level of care exercised by the blaster. This paper also suggests that the industry and/or ISEE develop and disseminate a comprehensive standard of care that courts can use to further justify a change from strict liability to negligence and evaluate the standard of care.

Jan 1, 2003

By Juan Lucero

Como consecuencia de los factores externos e internos, las empresas mineras necesitan ser más eficaces a través de la implementación de nuevas tecnologías e informática. En este sentido, la compañía minera Milpo disminuye los costos de hardware para así generar un control de operaciones más minucioso, automatizado y oportuno. Los principales logros obtenidos son el control detallado de las operaciones, los sistemas operativos son la base para obtener los costos operativos, una mejor formulación y control presupuestal, control de servicios de terceros y el de los sistemas integrados.

Sep 13, 2001

By Joseph Haid, om, Rio Yang, Kelly Fleetwood

Some coal mining operations in the Powder River Basin are currently observing a number of blast holes detonating sympathetically within their cast blasts. Sympathetic detonation can cause poor cast results, high blast vibration levels, excessive back break and fly rock, along with a number of other undesirable blast results. The reduction or the total elimination of blast hole sympathetic detonation is of paramount importance to the coal mining companies operating in the Powder River Basin. This paper describes a systematic approach to prevent cast blast holes from detonating sympathetically through the use of the electronic initiation and expanded blast patterns. In-situ measurements outlined in this paper were recorded from pressure probes, velocity of detonation probes and near field accelerometers, along with digital images generated from a high speed CCD camera. Large diameter angled drill holes were also checked for any measurable amount of deviation by a cable type borehole measurement tool. The field measurements provided the scientific evidence, statistical data, and documentation necessary to develop a sound method or a “road map” that would minimize and in some situations prevent the occurrence of blast hole sympathetic detonation.

Jan 1, 2005