Search Documents

Institute of Metals Division Ferrous and Nonferrous Physical Metallurgy Established as a Division April 26, 1918 (Bylaws published In the 1944 TRANSACTIONS Volume of the Division) A A SMITH, JR, Chairman E A ANDERSON, Past-Chairman F N RHINES, Senior Vice-Chairman W A DEAN, Vice-Chairman H A MALONEY, Treasurer ERNEST KIRKENDALL, Secretary 29 West 39th Street, New York 18, N Y Executive Committee R M BRICK 2 W A JOHNSON 1 H I DIXON 2 E W PALMER 1 M GENSAMER 2 J H SCAFF 3 J D HANAWALT 1 J D SULLIVAN 3

Jan 1, 1952

By E. Pribonic

Failure of a mine material hoist can cause injuries, fatalities and significant infrastructure damage, along with an associated loss of production. Principal causes of hoist accidents are overwind and underwind. Past and present means of arresting hoisting equipment are marginally effective and utilize destructive systems that are not reusable following an arrest. The use of permanent magnet eddy current arrestor technology is proposed; the history and fundamental science of the technology are presented, followed by real world examples and calculations of performance for failsafe, friction-free, instantly reusable eddy current arrestors as applied to stopping a 30-ton ore skip traveling at 16 metres per second. A comparison of existing arrestor types with the eddy current arrestor is included and limitations of the ECA are also discussed.

Jan 1, 2008

By Svato Prochazka

Content: ? commonly used drive systems ? drive system efficiency ? introduction to SR technology ? SR drive system advantages Commonly Used Feeder Drives Technologies ? VFD + induction motor ? hydraulic drive + hydraulic motor SR drive + SR motor

May 1, 2010

By R. Dahlke, J. A. Finch

"A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick Mine Concentrator to investigate the role of gas (air) superficial rate distribution (Jg profile) to the cells in the final Zn cleaning stage (bank of seven cells). Three profiles were tested: Balanced (each cell with same Jg), Increasing (from cell 1 to 7), and Decreasing, along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The Increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was traced to the response of the first few cells. The Increasing profile gave the highest selectivity of sphalerite against non-sulphide gangue (NSG) in these cells with relatively even recovery per cell down the bank (10-15% based on feed to each cell). The other profiles gave lower selectivity and higher zinc recovery in the first cells (up to 25% in cell 1), which combined to reduce overall bank performance. The increased selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG gangue. The Increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.INTRODUCTIONThe performance of a flotation circuit is largely the result of the operator’s response to visual clues. This includes manipulation of the gas (air) input and how it is distributed to cells in a bank. A lack of sensors prescribes this approach. Over the past ten years the Mineral Processing Group at McGill University have developed a set of gas dispersion sensors including one to measure gas superficial rate (or simply “gas rate”), i.e., volumetric gas rate per unit cell crosssectional area, Jg (Gomez and Finch, 2002). The device collects bubbles in a tube immersed in the pulp and infers Jg from the pressure-time curve generated after a valve is closed and air starts to accumulate. The usual units are cm/s. It is robust, reliable and suited for plant use.A version of the Jg sensor was tested extensively during 2000 at Noranda’s Brunswick Mine Concentrator (Dahlke et al., 2001). The results were sufficiently encouraging that a sensor was fabricated to suit local requirements (Insta-Jg). The sensor detected malfunctioning field instruments and flotation mechanisms, and demonstrated that gas distribution to cells in a bank “as found” had no particular pattern, or profile. Preliminary testing suggested that a balanced profile (i.e., all cells with the same gas rate) gave superior metallurgy (grade / recovery down the bank) than the “as found” profile. This observation prompted a focused campaign to explore the impact of the gas rate (Jg) profile, introducing the notion of “gas distribution management”."

Jan 1, 2004

By B. Mishra, A. Staley, D. Kirkpatrick

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90-wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct resulting in attempts for magnetic separation. These separations are desirable in the notion that there is no waste product generated from this type of processing and consequently an opportunity for complete utilization of the waste material. Conversely, the pre-separated material could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by established acid-leach process. This paper describes the results of alumina recovery and the plans for titanium oxide recovery from red-mud. In addition, the situation of ongoing efforts in iron extraction, particularly, the method of magnetic separation of the reduced material. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Critical assessment of the recovery sequence chosen for the products has been described based on economics.

Jan 1, 2001

By R. J. McLeod

"CONTROL STRATEGYThe Lake Dufault Division of Falconbridge Copper Limited has been concentrating a complex copper zinc ore since late 1964. An ARL X-ray on stream analyzer was installed in 1966 for process control. A Digital Equip-ment Corporation PDP8 was added in 1968 for more complete control. To improve the system the computer was exchanged for a Moded PDP-81 in 1971.The new computer is time sharing with 8K core memory and 32K disc storage. A new interface was installed to accommodate 14 X-ray streams and additional analog signals for process control. The system gave us additional capacity and flexibility to make changes in operating programs and control strategy while on line. As the computer is used for process control a modified focal language was chosen as the operating language for ease of operation. This language is more suitable for process control than for statistical work.The main components of the control system are(a) Computer(b) Interface(c) Production Control X-ray Quantometer(d) Teletype terminals(e)Reagent feeders(f) Sample SystemThe operation of the system consists in the computer selecting the various streams to be analyzed by a PCXQ Quantometer. When the flowing sample is presented to the X-ray the intensities of the various elements are read by the computer from analog to digital converter, the assays are then computed. From the tonnage and assays the computer is programmed to determine the amount of reagent added to various parts of the circuit. The computer drives the feeders via the interface for the required amount of reagent. After following a certain sequence the computer prints out the performance and control data on an ASR35 Teletype. The data is printed out approximately every seven minutes. Any des¬ired changes in the program or strategy can be made during operation via an ASR33 Teletype connected to the computer."

Jan 1, 1973

By J. Pei

The studies of dynamic measurements using stress wave theory has commenced in China. This paper introduces some practical experiences using "CASE method" in Shanghai showing applications of dynamic measurement to determine ultimate bearing capacity of pile, the change of capacity due to set up, determining the optimum bearing layer during pile driving, the efficiency of hammer system and integrity of pile and discussions of method concered.

Jan 1, 2010

Triboelectric Separation - Beneficiation of Coal The performance of triboelectric separators is highly sensitive to the selectivity of the particle charging process. This paper presents a quantitative study on triboelectric coal beneficiation. The performance of different charging media was studied. Stainless steel was identified as having a work function between that of coal and silicate gangue and found to be the optimum charging medium for coal beneficiation. Recent results from separation tests were performed where silicate gangue was separated from crude coal using a parallel plate free-fall separator are illustrated.

Sep 13, 2010

By Michael M. Hamilton

In 1984 and 1985 the U.S. Bureau of Mines performed a mineral survey of the South Jackson Mountains Wilderness Study Area covering 60,211 acres of mountainous terrain of Humboldt County in northwestern Nevada. Approximately 550 lode claims have been located within or adjacent to the study area from 1900 to the present. Total recorded production for the area is 28.19 ounces gold, 1,105 ounces silver, 959 pounds copper, 6,016 pounds lead, and 12,446 pounds zinc; an additional two carloads from one mine contained an unknown amount of metal. In early 1986, there were eight active properties with a total of 126 claims. Wescord Resources and Long Lac Exploration (Texas) Inc. are involved in a joint exploration of the Jackson Mountains for volcanogenic massive sulfide deposits. Development at the Claudia mine continues in 1986. Results of the survey indicate that there are no identified mineral resources or reserves within or adjacent to the study area. Twenty-two properties have mineral occurrences containing gold, silver, copper, lead, zinc, iron, antimony, vanadium, and cobalt, with silver, copper, and iron being the most abundant.

Jan 1, 1987

Mine wide, underground wireless communications are possible with the use of Ultra Low Frequency (ULF) technology. Due to the propagation through rock of ULF radio signals a relatively small antenna can provide communications coverage over a complete mining operation. Starting as a Personal Emergency Device (PED) for emergency messaging to miners under all circumstances, the ULF communications system has grown to include capabilities of remote control of underground equipment such as pumps and fans and centralised blasting initiation. This technology is now in use on 5 continents having lately made it onto the African mining scene. The paper and presentation will provide the audience with the benefit from international mining know-how in this technology as well as local African experiences. A recent commissioning exercise for example, is expected to pay for itself in electricity savings within a few months. These and other results from practical demonstrations and usage will be covered. This novel technology becomes an integral part of the daily operating infrastructure of a mine with immediate safety and business benefits. It is able to reduce capital expenditure and is designed for ease of routine operational use. The paper will conclude with insights into current R&D for further development of this technology.

Jan 1, 2007

By Thys B. Johnson

The mine system analysis and evaluation study presented in this report was part of the U. S. Bureau of Nines' Tertiary channel project conducted under the Heavy Metals program. The Badger Hill pit, located on the west end of the San Juan Ridge area, near Nevada City, California, was the site of the Bureau's field work. The objectives of this study were: (1) Determine potential alternative mining systems for some of the large tertiary channel gold-bearing gravel deposits, and (2) Identify areas of technology where further investigation would be merited because of their potential inclusion in a mining system for such deposits, The study involved the development of a mineralized block inventory, an economic block inventory, determination of optimum ultimate mining limits and a preliminary economic mining system evaluation. Computer programs were developed and utilized for each of the study phases stated above. The sampling program conducted at Badger Hill by the Bureau Delineation Group together with confidential drill hole data provided by the San Juan Gold Co. formed the basic gold values and distribution information from which a deposit model was developed. The deposit was divided into minable block units and net economic values were assigned to each block for various configurations of both open-pit and underground mining methods based on cost and performance data provided by the various Bureau of Mines Research Centers. A number of controllable variables such as: (1) Mining method (open-pit and underground), (2) depth of mining cut, (3) production rate and (4) equipment type and capacity were evaluated. The prime measures of effectiveness on which the mining systems where judged were discounted cash flow rate of return and maximum utilization of natural resources. The analysis showed that underground mining of the Six-Mile Tertiary channel gold-bearing gravel deposit under consideration was uneconomical and did not permit maximum recovery of the resources within the channel. It was also apparent that mining the Six-Mile Deposit for gold alone is uneconomical or at best marginal at a gold price less than $80 per ounce. The analysis showed that the potential for an economic mining operation within the Six-Mile Deposit exists when the gravel resources of the channel are considered together with the gold. It was determined that the highest rate of return would be realized with a 20-year open-pit mining operation yielding 745,000 ounces of -gold and 55 million cubic yards of usable gravel.

Jan 1, 2012

By Roger M. Turpening

This study was performed to examine the feasibility of using seismic shear waves to detect the presence of abandoned coal mines. !he Antiquity Coal Mine near Antiquity, Ohio was used as a region of known voids. No attempt was made here to accurately locate the mine tunnels if detection was obtained. The results of this study were positive. Sharp changes in the amplitude of the received shear waves were clear indications of the presence of a fluid (gas or liquid) filled region between the source and receivers. When moving the source showed no change in the received signals it was concluded that the voids existed beneath the sensors. Prior to these tests drilling (SM-3) had determined that a void did exist in this area. This void was confirmed by this shear wave test and two additional voids were found.

Jan 1, 2012

By E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has been conducting re-search to determine the influence of mining machine mounted water sprays on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery. Airflow speeds and directions were measured at several locations near the face with ultrasonic anemometers. Methane was released from the face and concentrations were measured in the entry at locations above the mining machine using fixed point methanometers. Changes in airflow speed, direction, and methane concentrations were correlated with water spray operations. The test results using different spray arrangements and water pressures showed that operation of the machine-mounted sprayers can improve face ventilation effectiveness by increasing the velocity of airflow moving toward and away from the face. The improved ventilation resulted in reduced methane levels near the face.

The following report summarizes the results of engineering feasibility studies whose purpose was to assess the probable efficiency, reliability, safety and cost of a number of possible methods for removal of radon gas from the ambient air in underground mines. Fourteen candidate techniques were evaluated. Seven of these were based on specific individual principles, and seven were based on combinations of these principles. The individual principles were as follows: 1. Activated charcoal 2. Organic fluids 3. Semipermeable membranes 4. Molecular sieves 4. Cryogenics 6. Chemical reaction 7. Centrifuge The combinations were: 8. Cryogenics and activated charcoal 9. Cryogenics and molecular sieves 10. Cryogenics and chemical reactions 11. Membrane filters and organic fluids 12. Membrane filters, cryogenics and activated charcoal 13. Membrane filters and chemical reactions 14. Silica and an Organic Fluid

Jan 1, 1975

By C. L. Reichardt

Mining companies are increasingly looking to the developing world for the next generation of mining projects, often in countries that have little or no previous history of large-scale mining. One of the major challenges for such projects is hiring?and retaining?personnel that have technical skills and experience in mining-related disciplines. Staffing a mine with an expatriate workforce is neither cost-effective nor sustainable, and many countries now insist that mining companies ?transform? the profile of their workforce to more closely mirror the demographic profile of the host population. The need to nurture mining-related skills in emerging mining nations is not solely limited to the workforce: there are also pressing economic and sustainability imperatives to develop capacity within local service providers such as consultants and contractors, as well as to facilitate informed engagement between mining companies, government and civil society. However, few educational institutions in emerging mining nations currently have the ability to offer practical training in mining-related disciplines. Local employees who are sponsored by companies to develop their skills through international study maybe impeded by language and cultural barriers, and may also be taught using course content that is of limited relevance to the specific challenges of their future working environment. This paper addresses the challenge of skills development and retention in emerging mining nations and uses examples from sub-Saharan Africa and the Asia Pacific region to explore practical means of developing capacity in mining-related disciplines. It examines the need for companies to implement strategies to develop local technical capacity in countries where they envisage a long-term operational future and also highlights the need to foster partnerships between academia, developmental institutions, mining companies, governments and civil society to establish the critical mass of mining-related skills required to nurture the development of a sustainable mining industry.

Jan 1, 2009

By Moorrees C, Everson P

A detailed examination of carbonic acid leaching of crude iron-containing magnesia derived from Savage River magnesite shows that the rate and extent of magnesium and iron dissolution are affected by the slake time, leaching temperature, carbon dioxide pressure, pulp density and rate of agitation. In order to produce high-purity magnesia from the leachate by precipitation and calcination, the optimum leaching conditions, which are those that yield maximum magnesium and minimum iron dissolution, have to be a compromise in terms of the above parameters. For example, iron dissolution can be limited by leaching at an elevated temperature (-45°C), but because the maximum concentration of magnesium biearbonate decreases rapidly with an increase in temperature, it is necessary to use a low pulp density (-2 per cent solids) in order to achieve an acceptable degree of magnesium dissolution.Evidence is obtained that iron dissolution involves the formation of a soluble ferric bicarbonate complex that decomposes at elevated temperatures. The extent of iron dissolution is much higher than might be expected and it is probably because the original magnesite contains siderite in solid solution with the magnesite; on calcination, the hematite whieh is formed is in a very finely divided condition and hence more reactive.

Jan 1, 1983

By Dennis L. Paisley, Thomas P. Turner

Laser slapper detonators are the next generation detonator under development at the Detonations Systems Group at Los Alamos National Laboratory and function very similarly to an electrical slapper. A fiber optic transmits a laser pulse to ablate a thin metal film. This film, or flyer as it is commonly called, is launched through a short barrel to km/s speeds. The flyer shock loads or slaps a high density pressing of secondary explosive, setting off a detonation therein. Laser slapper detonators afford a number of safety advantages over other conventional detonators. Most important they require very high peak laser powers to operate, orders of magnitude larger than possible sources of natural or man-made accidental stimulus. Because light is transported over fiber optics, laser slappers avoid many of the electrical hazards associated with detonators. Use of insensitive, secondary explosives makes these detonators safer to handle, manufacture, transport, and deploy.

Jan 1, 1994

By S. Gallagher, A. G. Mayton

Back injuries account for a high proportion of lost workdays in the mining industry and are a leading cause of disability in mine workers. Two risk factors for low back injuries are manual lifting and whole-body vibration exposure when operating mobile equipment. Recent research has shed light on possible mechanisms through which low back injuries may occur, and the results of these studies can be used to improve the design of lifting tasks and seats to decrease injury risk. This article discusses recent research results and how this knowledge can be leveraged to reduce the risk of low back pain.

The spatial and temporal evolution from the porphyry to high-sulphidation epithermal environment can be assessed by integrating new results on such deposits (Arribas et al, 1995; Hedenquist et al, 1998) with past studies of plutonic and porphyry systems (Dilles and Proffett, 1995; Cline, 1995; Shinohara and Hedenquist, 1997; Hedenquist and Richards, 1998). Some time ago, Sillitoe (1973) argued for the nature of the tops and bottoms of porphyry deposits. He concluded that epithermal deposits may form over the tops of some porphyry systems. We can now conclude more confidently what the tops and bottoms of many high-sulphidation ore deposits appeared like while active (Arribas, 1995; Hedenquist, 1995). In addition, we better understand the nature of the zonation of high-sulphidation epithermal systems from the intrusive to surficial environment (Sillitoe, 1999), and how these two styles of ore deposit are related. Geological and geochemical evidence clearly indicates a continuum between these two ore environments. This improved understanding of genesis allows more efficient exploration for these deposits. There are many examples of spatially associated porphyry and epithermal ore deposits. A genetic connection has been suggested by some, and argued against by others. Nowhere is this spatial association better seen than in northern Luzon, Philippines, where the Lepanto high-sulphidation epithermal Cu-Au deposit overlies the Far Southeast (FSE) porphyry Cu-Au resource (Figure 1). Together these mineralised bodies contain a resource of >3.8 M tonnes Cu and >550 tonnes Au. Lepanto was largely mined out in early-1997. Post-war production until 1995 was 0.73 Mt Cu, 115 t Au and 393 t Ag at an average grade of 2.2 per cent Cu, 3.5 g/t Au and 11 g/t Ag. The recent discovery of the adjacent Victoria low-sulphidation quartz-Au-base metal vein deposit, with a resource of >68 tonnes Au (Cuison et al, 1998), illustrates the variety and abundance of mineralisation in the Mankayan district. This district also hosts the Guinaoang porphyry Cu-Au deposit (Sillitoe and Angeles, 1985) and other epithermal vein occurrences (Figure 1). This brief summary reviews the results recently published on the Lepanto-FSE deposits (Arribas et al, 1995; Mancano and Campbell, 1995; Claveria, 1998; Hedenquist et al, 1998), and stresses the evidence for coupling of mineralisation between the porphyry and high-sulphidation epithermal environments.

Jan 1, 1999

By P. A. Selvadurai

This paper presents the results of a research investigation leading to the development of a technique for the measurement of the surface permeability of Indiana Limestone. The tests are conducted on a cuboidal block of the limestone with a flat surface that can be sealed to create a circular aperture through which water influx can take place. Computational results for Darcy flow are used to interpret the results of the experiments. The water entry area can be moved over the surface area of the block to investigate, quite conveniently, the distribution of permeability across the surface of the limestone block sample.

May 1, 2009