Search Documents

By P. N. Mohan Das, K. Harikrishna Bhat

"The major ilmenite reserves are located in India at Chavara (CH), Manavalakurichi ( MK) and Chatrapur, Orissa (OR). India stands first in terms of ilmenite reserves, which are estimated to be 278 million tonnes out of which, 142 million tonnes are processable. Mineralo-chemical analysis showed that Chavara ilmenite is the most weathered one with about 60% TiO2 while Chatrapur is the least weathered with about 50% TiO2. XRD and SEM studies of different magnetic fractions of these three mineral deposits established the co-existence of ilmenite with pseudorutile, rutile and haematite phases in substantially varying amounts. It is observed that the tropical weathering rather than the source rock difference has apparently played an important role in imparting major compositional and structural dissimilarities among the ilmenites in different places. Further, the chemical analysis, XRD and SEM characterisation of differently weathered samples of MK ilmenite separated by the magnetic fractionation showed that the degree of alteration was invariably associated with the decrease in magnetism, increase in the rutile phase and the change in Fe2+/Fe3+ ratio of ilmenite grains. Magnetically separated fractions when subjected to metallisation with carbonaceous reductant such as coke showed that the degree of reduction increases with the degree of alteration and with the decrease in the Fe2+/Fe3+ ratio.In the processing of ilmenite through the Becher process, aeration rusting of pre - reduced ilmenite is found to be the rate-limiting step thus, affecting the productivity and economy of the process. Investigations have proved that the addition of some organic compounds such as glyoxal, sucrose etc., to the system accelerates the reaction to such an extent that the rusting time has been reduced to less than half. The formation of acids by the these organic compounds during the rusting reaction was proved responsible for maintaining the pH of the solution in the range 3-4 at which iron hydroxide do not precipitate and block the pores in the reacting surface of the grain."

Jan 1, 2003

By A. Kazemi, M. A. Ahmadi

Pressure tunnels are constructed nurously in related with powerhouse. In some cases, according to high internal water pressure, rock mass around tunnel can seldom suffer this pressure. So installation of concrete lining which interacts with rock mass and suffers parts of this pressure and transfers the rest of the pressure to the rock. In this paper hydromechanical interaction between rock and lining is investigated. With using empirical and numerical methods concrete lining for Symareh waterway is designed. Initial support of 10 cm reinforced shotcret with wire mesh and rock bolts pattern of 2.5*2.5 m with length of 4 m is suggested. By using FLAC package final lining with paying attention to axial force and momentum in reinforced concrete was designed. Reinforced concrete with 60 cm thickness and two rows of bars, 18 mm diameter and 20 cm spacing are designed. Also for preventing cracks in concrete which caused by the change of temperature and shrinkage, bars with 10 mm diameter and 25 cm spacing, and also bars with 8 mm diameter and 10 cm as minimum shear bars are suggested. Plusieurs galeries en pression se construisent en liaison avec les centrales électriques. Dans certaines galeries, suite à une haute pression interne de l'eau, le massif rocheux autour de la galerie ne peut pas supporter cette pression. L'installation d'une couche de béton a l'intérieur de la galerie donc réagit avec les roches et support d'une partie de cette pression et transfère le reste de la pression aux roches. Dans ce papier, l'interaction hydromécanique entre la roche et la couche en béton a été étudiée. En se basant sur les méthodes empiriques et numériques le système de support de galerie de passage d'eau de Saymareh a été conçu. Un soutènement initial d'une épaisseur de 10 cm de béton étant renforcé par un grill métallique et une maille de boulon (2.5 * 2.5 m) d'une longueur de 4 m a été proposé. En utilisant le logiciel de FlAC, la couche finale en béton selon les forces dans le béton a été conçue. Le béton renforcé d'une épaisseur de 60 cm et deux ranges d'armateurs (18 mm de diamètre) avec un intervalle de 20 cm a été conçu. De plus; pour éviter des fissures dans le béton suite au changement de la température et de l'extraction, des armateurs de 10 mm de diamètre et de 25 cm d'intervalle pour augmenter la résistance au sciesiement du béton ont été proposes Unter Druck stehende Tunnels werden hauptsaechlich im Zusammenhang mit Kraftwerken gebaut. In einigen Faellen, wo der Wasserdruck zu hoch ist, Kann selten die Felsenmasse diesen hoehen Druck allein aufnehwen. Deshalb werden sie mit Betonauskleidung versehen, die wegen guter Wechelwirkung mit der Felsenmasse einen Hauptanteil des Druckes aufnehmen Kann, wobei der Rest an die Felsenmesse weitergeleitet wird. In dieser Arbeit wird die hydromechanische Wechelwirkung zwischen der Gesteinmasse und der Auskleidung untersucht. Mit Hilfe empirischen und numerischen Verfahren sowie Kombination der beiden wurde eine Betonauskleidung fuer die Symareh Wasser Kannal koustruiert. Als erstes wurde ein 10Cm dicker armierter Beton mit einem Mashengitter von 2.5*2.5 sowie den gleichen Felsbolzenabstaenden und einer Laenge von 4 m vorgeschlagen. Mit Hilfe des FLAC Programms wurde die Hauptauskleidung unter Beruecksichtigung von Axialkraeften und Momenten im Stahlbeton koustruiert. Der 60 Cm dicke Stahlbeton wurde mit zwei Reihen von Stangen, 8 mm im Durchmesser und in Abstaenden von 20 Cm koustruiert. Ferner im Sinne der Vorbeugung gegen Rissen im Beton, die durch Temperatur aendeungen und Schrumpfungen bedingt sind, wurden Stangen mit 10 mm Durchmesser und 2.5 Cm Abstaenden zur Erhoehung vor Scherfestigkeit des Betons vorgeschlagen.

Jan 1, 2003

By A. C. Apling, N. B. Barrett

Roadstone production requires the generation of non-flaky material, as outlined in British Standard 812 section 105.1; with respect to this criterion, a mathematical model of a cone crusher must be able to predict the flakiness index of a particular size range as determined by the relationship between thickness and nominal size. The Whiten cone crusher model utilises breakage and classification functions to predict a product particle size distribution only, so a shape function has been proposed that is based on a phenomenological approach, taking into account the transfer between flaky and non-flaky material at each stage of breakage. The results of laboratory tests to determine material breakage characteristics and of examination of pilot-scale test products illustrate the method's potential

Apr 1, 1995

By Juliana Gutiérrez-Paredes

Keywords: Slag, chromium oxide, recovery, stainless steel Experimental and theoretical work was performed to estimate the effect of slag basicity and amount of reducing agents on the reduction of chromium oxide from the slag which interacted with molten steel at 1600°C. The slag system contained CaO, MgO, SiO2, CaF2 and Cr2O3 together with Fe-alloys (Fe-Si and Fe-Si-Mg). The CaF2 and MgO contents in the slags were 10 mass % each; Cr2O3 was 25%. The amount of the ferroalloys ranged from 12.5 to 50 g per 100 g of slag. The (CaO+MgO)/SiO2 ratio was held at 1 and 2. The Cr yield was determined using both Fe-alloys as reducing agents. Some estimations were made to determine the theoretical effect of temperature, slag basicity, (CaO+MgO)/SiO2, and amount of reducing agents in the slag on the chromium recovery. The FACT (Facility for the Analysis of Chemical Thermodynamics) computational package is used to determine the equilibrium between the slag and molten steel.

Jan 1, 2005

By Elaine Araújo

Since the ancient times, clays were used as decolorant material for various types of oils. These clays were called ?decolorant clay?. They have the property to decolor dye materials present in mineral oils, plants and animals. Biofuel is a fuel derived from biomass of live organisms. As biodiesel is produced from renewable sources, the generation of employment due to industrial scale production may cause a reduction in the dependence on foreign diesel importing, as well as the reduction of air pollution by the addition of biodiesel to diesel. This study aimed to develop a technological process to decolor post- consumption oil to be applied as biofuel. The results were characterized by techniques of XRD (X-ray diffraction), X-ray fluorescence and FTIR (Fourier Transform Infrared). It was observed that the post-consumption oils presented a higher decoloration result after treatment with the Brazilian clay.

Jan 1, 2009

By J. C. Pandey

The paper highlights the experimental investigations to characterize texture and plastic strain ratio r-Bar in auto grade steel sheets by ultrasonic measurements, whereas attempts were made to characterize interlamellar spacings in pearlite, tensile stresses and torsional properties in prestressed concrete wires by eddy current measurements. Good correlations were obtained between the testing parameters (such as ultrasonic attenuation and velocity in case of steel sheets as well as eddy current out put voltage and phase angle in case of steel wires) and the materials properties (such as texture, plastic strain ratio r-Bar, interlamellar spacings in pearlite, tensile stresses and torsional properties). 15 MHz normal direct contact and 20 MHz delay line normal shear wave probes were used for ultrasonic measurements. Eddy current measurements were done using an absolute coil probe with variable frequency selection. The experimental results show the possibility of nondestructive on line measurement of the above microstructures and properties.

Jan 1, 2010

By M. Yavuz

Underground mining method selection (UMMS) is one of the most important issues in mining engineering. Underground mining method should be primarily selected to make use of underground resources optimally. It is nearly impossible to change the mining method once selected by the reasons of rising costs and mining losses. Because of these reasons, UMMS process is extremely important in mine designs and economics. The strategy of underground mining method selection has been studied by different researchers in the literature. Boshkov and Wright (1973) proposed a classification system; Morrison (1976) suggested a selection chart; Laubscher (1981) proposed a selection methodology; Nicholas (1981) presented a classification system; Hartman (1987) developed a selection chart and Miller-Tait et al. (1995) modified the Nicholas? system and developed the UBC mining method selection process. In reality, UMMS is one of the important Multiple Attribute Decision Making (MADM) problems and mining engineers have always some difficulties in making the right decision in the multiple criteria environment. To make a right decision on UMMS, all known criteria related to the mining method selection should be analyzed and the problem solved according to suitable decision making techniques. A review of the literature reveals that decision making techniques have been used for UMMS applications. Kesimal and Bascetin (2002), Bitarafan and Ataei (2004), Bascetin et al. (2006), Alpay and Yavuz (2007), Karadogan et al. (2008) and Samimi Namin et al. (2008) used decision making techniques in UMMS applications. In this paper, two different MADM methods: Analytic Hierarchy Process (AHP) and Fuzzy Multiple Attribute Decision Making (FMADM) are applied to select the optimal underground mining method for a chromite mine and final solutions are then compared. THE AHP METHODOLOGY The AHP method developed by Saaty gives an opportunity to represent the interaction of multiple factors in complex unstructured situations (Triantaphyllou, 2000). The method is based on the pair-wise comparison of components with respect to attributes and alternatives. A pair-wise comparison matrix n×n is constructed, where n is the number of elements to be compared. The method is applied for the hierarchy problem structuring. The problem is divided in to three levels: problem statement, object identification to solve the problem and selection of evaluation criteria for each object. After the hierarchy structuring, the pair-wise comparison matrix is constructed for each level where a nominal discrete scale from 1 to 9 is used for the evaluation as shown in Table 1 (Saaty, 1980; Saaty, 2000). The next step is to find the relative priorities of criteria or alternatives implied by this comparison. The relative priorities are worked out using the theory of eigenvector. For example, if the pair comparison matrix is A, then, [Amax=××- [1] ] To calculate the eigenvalue ??max? and eigenvector w=(w1, w2,..., wn), weights can be estimated as relative priorities of criteria or alternatives. [ ] Since the comparison is based on the subjective evaluation, a consistency ratio is required to ensure the selection accuracy. The Consistency Index (CI) of the comparison matrix is computed as follows: [CImax--= [2] ] where ?max is maximal or principal eigenvalue, and n is the matrix size. The consistency Ratio (CR) is calculated as: [CR= [3 ] where ?RI? Random Consistency Index. Random consistency indices are given in Table 2. [ ] Table 2. The consistency indices of randomly generated reciprocal matrices As a general rule, a consistency ratio of ?0.10? or less is considered acceptable. In practice, however, consistency ratios exceeding ?0.10? occur frequently. THE FMADM METHODOLOGY The FMADM methods have been developed due to the lack of precision in assessing the relative importance of attributes and the

Jan 1, 2009

By Kenneth G. Skinner

The rapid growth of the metallurgical, chemical, and allied industries on the Pacific coast just prior to and during the war caused a sudden increase in the demand for refractories, which was the immediate cause of a revival in interest in refractory clays available on the Pacific coast, particularly in the Pacific Northwest. Population increases and shortage of shipping facilities caused an increase in the amount of various ceramic materials and products used and produced on the Pacific coast, with accompanying demand for information regarding sources of clay. In an effort to supply part of this information, the Bureau of Mines, in cooperation with the College of Mines, University of Washington, started a program in 1944 to test the refractory and other properties of clays from seven Pacific Northwest deposits that had been drilled and sampled as part of the Bureau of Mines alumina from clay investigation. Figure 1 shows the location of these deposits.

Jan 1, 1949

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitlted "Evaluation of Proximity Warning Devices II dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electro-static fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factory of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By Terry Keough

Contents for discussion ?Current liner technology ?Innovation of magnetic products ?Development of magnetic wear liners ?Installation and change out method ?Uses and capabilities ?Internal wear liners ?Summary Vulcanized rubber ?Many of you are familiar with using vulcanized rubber to provide wear protection on mining equipment. For years, this was the standard for most mining equipment, and mines spent a lot of money fabricating and lining steel equipment.

May 1, 2010

By B. A. Osei

Research to evaluate possible metrics for predicting dredgeability of compact aggregates, by hydraulically actuated clamshell dredges, shows work done by the pistons as a viable metric. Analysis of field data shows that there is a low, positive, correlation between cycle time (CT) and work done. If this correlation exists, then CT has to be considered an independent variable affecting work done during dredgeability assessment. Further research is required to elucidate the relationship between CT and work done during dredging. The objective of this paper is to test the hypothesis that work done during dredging increases with increasing CT. Kinematics and dynamics of the hydraulic clamshell were modeled and implemented in Simulink® in MATLAB. The model was validated using field data. The model was then used to test the research hypothesis. The results show that work done increases with increasing CT. This work confirms that work done during dredging increases with increasing CT. This result indicates that though an operator can increase the CT to deal with difficult digging, inputting unduly high CTs results in higher energy consumption during dredging.

Jan 1, 2011

By David M. R. Stone

Underground mining in the gold industry is gaining popularity in Nevada, and with it the use of cemented rockfill is becoming mainstream. Even with today?s high metal prices, however, mining companies are very sensitive to the margins they realize, and are constantly looking for ways to reduce costs or improve efficiencies. Given that the backfill is one of the largest cost centers in underground mining, mines are constantly under pressure to reduce backfill costs. This paper will present an overview of the factors that impact cemented rockfill quality in Nevada mines based on the authors many years of consulting experience. Cemented rockfill quality can be linked directly to binder consumption, hence programs aimed at improving quality generally result in lower binder costs, better performance in the fill (hence less dilution), and improved safety. The paper will conclude with the key elements of a comprehensive program of backfill quality assessments and backfill QA programs. Comparative laboratory and minesite data from a number of operating and proposed mines will be presented.

May 1, 2007

By Sander Mul, Michael Brandner, Armin Paar

Graphitic HSS roll grades such as ESW’s brand VANIMO can be considered as the latest developments for the last finishing stands in hot strip mills. These roll grades are developed on the basis of the alloying concept of (Carbide Enhanced) Indefinite Chill work roll materials. During the development of VANIMO, the amounts and types of carbide forming elements were increased and adjusted into the direction of cast HSS roll grades. The microstructure of graphitic HSS roll grades therefore consists of tempered martensite, cementite and several different carbide types as well as a well-defined amount of free graphite. The main purpose of graphitic HSS roll grades is to combine the high surface quality of Indefinite Chill alloys as well as the high wear resistance of HSS roll grades. Several systematic steps were taken to increase the wear performance from Carbide-Enhanced Indefinite Chill grades to the more advanced VANIC grade and further on to the highest alloyed roll grade VANIMO. In every development step, the surface quality of the roll grades was carefully monitored. The decision to invest in new testing equipment at ESW’s plant was driven by the wish to see microstructural effects of different alloys in a macroscopic dimension. Usually samples are taken from cast rolls and investigation is done in comparably small areas compared to the total surface of a roll. Rolling of strip is done with the entire barrel, so effects of alloy and microstructure can appear anywhere on the barrel surface. To ensure better understanding and deeper knowledge about influences of alloying trials we decided to install the last version of LRI (Lismar Roll Inspection). LRI includes the latest technology of Eddy Current with an enormous resolution. Depending on the formation of carbide precipitations, carbide network as well as matrix and free graphite, the EC test can detect smallest differences. The possibility to analyze the different results of EC and UT surface wave inspection will be discussed. A few examples of surface effects in the mill application will be discussed and improvement strategies explained.

Oct 1, 2019

By A. E. Hall, R. N. Taylor, J. G. Taylor

The introduction of tunnel-boring machines to South African gold mines has created problems and challenges which accompany any new technique. This paper describes the experience gained in this field, especially in the design and erection of a tunnel borer and in boring and environmental conditions.

Jan 1, 1978

By Minoru Kawamura, Shinya Tanaka

In Japan, a cartridged emulsion explosive is generally used for tunneling. The workers are compelled to approach the face on charging the explosives into the drill hole with the tamping rod. Therefore, the workers are exposed to the risk of the disaster with the cave-in and the falling rock. The mechanization of the tunnel work has been advancing gradually. Especially, the development of the mechanization for charging work is desired in order to avoid the risk of disaster on workers. Recently, some charging machines such as the bulk emulsion explosives have been evaluated. However, a universal method has not been established yet, because the evaluated machines were not adequately suited from the point of the regulations and the consumption style of explosives.

Jan 1, 2008

By L. D. Jaffe

IN previous metallographic work on titanium and its alloys, difficulty has been encountered in distinguishing spheroidal particles of titanium hydride, dispersed in a-titanium, from other phases that may be present, such as p-titanium. This problem is common in examination of commercial unalloyed titanium.' In the course of an investigation of the Ti-H phase diagram, it was noted that titanium hydride, dispersed in a matrix of a-titanium, showed strong optical anisotropy when examined under polarized light. With sensitive tint illumination, particles of the hydride, when the stage is rotated, changed from bright yellow to bright blue in color. Since P-titanium is cubic, it showed no color change on rotation, remaining dark gray or blue-gray. Although a-titanium is hexagonal, it showed only a minor color change, going from pale pinkish-blue to pale purplish-blue. These colors could be modified somewhat by adjustment of the illumination. They were observed in specimens mechanically polished, both without etching and after etching with hydrofluoric acid-nitric acid mixtures in either water or glycerine. The strong color change of the hydride seems to offer a simple method for its metallographic identification. Optical anisotropy of titanium hydride is inconsistent with its accepted face-centered-cubic structure.' Samples of iodide titanium containing 6 to 40 atomic pct deuterium were prepared for diffraction studies. After deuterating and slow cooling' the samples were held 21 % hr at 400 °C, water quenched, held 61 hr at 100°C and quenched, then held 64% hr at 255 C and quenched. Debye ex-posures with MoKa X-rays and 1.111A neutrons were made at room temperature of samples as-deuterated and after the 100" and 255°C treatments. Table I shows the lines observed, in addition to those attributable to a-titanium. These data show that the hydride phase was not cubic, but probably tetragonal. The titanium atoms appeared to form a body-centered-tetragonal lattice complex, two titanium atoms per cell, with approximate dimensions: a = 3.12A, c = 4.18A, and c/a =1.34A. This is equivalent to a face-centered-tetragonal complex, four titanium atoms per cell, with approximate dimensions: a = 4.42A, c = 4.18A, and c/a - 0.946A. The presence of the 2.98 and 1.81A neutron lines indicates that the true Bravais lattice is not identical with this lattice complex, but may be primitive tetragonal with dimensions some multiple of those of the complex. The relative intensities of the hydride and a-titanium X-ray lines as functions of overall composition indicated that the hydride, presumably in equilibrium with the a at 100" to 255"C, contained more than 62 atomic pct H. Acknowledgments The experimental work covered in this report was done at Brookhaven National Laboratory, through the courtesy of D. Gurinsky. The cooperation of J. Sadofsky, 0. Kammerer, A. McReynolds, and A. Cendrowski is gratefully acknowledged.

Jan 1, 1957

By Paul L. Russell

Interest in the western oil shales of the US began in about 1908, with the first retort in Colorado constructed in 1917. The most successful early developments were near Elko, NV, where the Catlin Shale Products Co. produced more than 1.9 dam3 (12 000 bbl) of shale oil during 1920-1924 and at Rulison, CO, where a US government operation produced about 570 in 3 (3 600 bbl) of shale oil during 1926-1929. Plentiful low-cost crude oil was developed about this time and shale oil was of little or no interest until after World War II. From 1944 to about 1972, several companies, and the US government, operated shale oil mines and recovery plants in Colorado. While technical successes were achieved and an estimated 40-56 clam' (250 000-350 000 bbl) of shale oil were produced, economics were not favorable and commercial production was not achieved. In recent years domestic production of crude oil supplies has not kept pace with US consumption. The growing shortfall has been met with imports. The cost of imported oil has continued to escalate and increased US dependence on petroleum imports are national concerns, because of the negative impact on US balance of payments and an increasing dependence on other nations for US energy needs. In 1978, petroleum imports equaled about 44% of demand, up from 23% in 1970, but down from 48% in 1977 because of availability of Alaskan North Slope crude oil. Reduced domestic consumption and other factors have reduced current imports to about 40-45% of de¬wand-but at ever increasing cost. The growing shortage of crude petroleum and its increasing cost have resulted in renewed worldwide interest in oil shales. In the past, the main obstacle to oil shale development (progress toward commercial production) has been economics-shale oil cost too much to develop and thus could not compete with conventional petroleum crudes. Even with today's inflated energy prices, some experts say the production of synthetic crude oil from oil shale is, at best, marginally economic. The 1973-74 Arab oil embargo and increased crude oil costs-along with the federal government's offer to lease oil shale lands-resulted in renewed

Jan 1, 1981

By P. Niessen, W. C. Winegard, C. J. Beingessner

DURING the last 10 years, several grain-growth studies have been made using zone-refined metals with controlled amounts of solute to elucidate the interaction of solute with moving boundaries. In all these studies, it was more or less implicitly assumed that the alloys used were, after recrystallization and grain growth, homogeneous within the grains with respect to solute and lattice defects. This note deals with observations made on microstructures originating from solidification of dilute alloys and from grain growth. Briefly, the experimental procedure used in these studies was the following: zone-refined cadmium and master alloys were melted and cast in Pyrex under vacuum to produce bars 14 mm in diam and about 150 mm long. These bars were cut into 8-mm-thick slices which were mechanically and chemically polished. The specimens were then deformed 30 pct in compression and given a 1-week anneal at 260°C in argon. After this anneal, a second deformation produced completely recrystallized samples 4 mm thick. The time-temperature controlled anneals were carried out in a bath of silicone oil. After the grain-growth anneal, the specimens were polished in Gil-man's' solution (33 g CrOs, 6 g NazSO, in 100 ml of water). Several etches were used depending on the alloy investigated, but mostly a mixture of concentrated HC1 and HNOj (98:2 vol) was employed. In all the alloys examined, the ease with which substructures could be revealed depended strongly on the crystallographic orientation of the surfaces of the grains. However, very frequently the microstructures to be discussed here etched up over broad areas comprising several grains. Fig. 1 is a micrograph of a Cd-0.05 at. pct Mg alloy annealed for 100 sec at 270°C. Different substructures are seen in this photograph. A denotes the now existing grain boundaries. The well-defined lines and points marked B are the remains of a solidification substructure. The lines are boundaries between cell colonies, and the points are nodes located on regular two-dimensional cells. This cellular structure has the same appearance as that found by weinberg2 for rapidly quenched Zn-Au alloys. The "ghost boundaries", marked C, are very similar in appearance to a grain boundary array in a polycrystalline sample. Repeated polishing and etching showed that all the substructures observed were three-dimensional. To date, the ghost boundaries have been clearly observed in all samples containing 0.005, 0.01, 0.05, and 1 at. pct Mg, and in samples containing 0.01 at. pct Zn. Attempts to outline these ghost boundaries in cadmium alloys containing 0.01 at. pct Ag and Au were only partially successful. In these alloys, parallel lines, having a resemblance to the ghost boundaries in the Cd-Mg and Cd-Zn alloys, were observed, but it was not possible to obtain complete arrays of ghost boundaries which extended over several grains. It is possible that a different etch than that presently employed would reveal the ghost boundaries in the Cd-Au and Cd-Ag alloys as clearly as in the Cd-Zn and Cd-Mg alloys. A close examination of the ghost structure showed that it consisted of linear etch-pit arrays, Fig. 2. The ghost boundaries were resolvable even in grains which showed over-all faceting due to the etching, as seen in the corner of Fig. 2. The general appearance of the ghost structure suggests that it originated during grain growth. This is supported by the observation that the mesh width in the ghost-boundary array generally increased with increasing final grain size. To test whether the ghost structure was formed during the long homogenizing anneal or during the grain-growth anneal, some as-cast samples were deformed and given a grain-growth anneal. This anneal was terminated by air cooling or

Jan 1, 1967

Kinetic Behaviour of Solid/Solid Separation of Ultrafine Particles in Aqueous Suspension

Sep 13, 2010

By Maria I. De Rosa

Table 46 and figure 16 show the number of fires and fire injuries for metal/nonmetal mills by state during 1990-2001. Table 46 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 77 fires occurred in 26 states. Thirty-seven of the fires caused 41 injuries and 1 fatality (including 5 fires and 3 injuries involving contractors). The yearly average was 6.4 fires and 3.4 injuries. Fifty-four fires with 26 injuries and 1 fatality occurred at metal mills; 23 fires with 15 injuries occurred at nonmetal mills. The Ewhr value was 845 x 106 hr (Irr = 0.01), and the LWD value was 6,681. Minnesota had the most fires (16 fires and 5 injuries), followed by Arizona (9 fires and 3 injuries), Wyoming (8 fires and 3 injuries), Nevada (7 fires, 4 injuries, and 1 fatality), and Texas (4 fires and 7 injuries). Of these states, Texas had the highest injury risk rate value (Irr = 0.033). Table 47, partly illustrated in figure 17, shows the number of fires, fire injuries, fire fatalities, risk rates, employees' working hours, and lost workdays by time period. The number of fires increased slightly during the second period, then decreased during the remaining periods. The number of fire injuries show a decrease during most of the periods (an increase is seen during the third period), accompanied by a decline in employees' working hours during most of the periods. The Irr values follow patterns similar to those shown by the injury values. Tables 48-53 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 18 shows the major variables related to fires for 1990-2001. Table 54 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004