Search Documents

By Carlos Lam, Joram M. Amir, Erez I. Amir

"Abstract The modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic loading tests on piles. This value is commonly assumed to be constant with depth though it may not be true for deep bored piles due to the chosen casting method and/or selfweight consolidation. To provide evidence to support this proposition, the results of compressive strength tests on core samples taken from four different studies have been presented. The results show a marked increase in the strength and stiffness values with depth. The results of crosshole ultrasonic tests conducted at another site also confirm the same pattern. It is therefore recommended that before load testing a pile the distribution of the E values along the pile axis should be investigated. This will ensure the use of a realistic elastic modulus value and hence the correct interpretation of thedistribution between the shaft and end resistances.IntroductionThe modulus of elasticity of pile material (E) is an important parameter for the interpretation of both static and dynamic load tests on piles. Multiplying E by the strain measured by either strain gauges (e.g. ASTM D4945) or tell-tales (e.g. Geffen and Amir, 1971) gives the stresses acting at a given pile section. Typically, in the absence of better information, the value of E is derived from laboratory tests on concrete cubes or cylinder specimens taken on site and is assumed to be constant along the pile. While this may be correct for pre-fabricated concrete piles that are cast in horizontal molds, it may not be true for cast-in-place piles that are produced in the vertical position.There are at least two factors that may contribute to the change in concrete properties with depth in a bored pile. First, the casting methods may be by free fall in dry holes (e.g. Kiefer and Baker, 1994) or by using a tremie tube if support fluids are used. In the former case, the earlier batches reach the bottom of the pile bore at a higher velocity and are thus compacted under higher energy. Second, regardless of the casting method, the fresh concrete in the pile bore will always consolidate at least partially under its own self weight. The materials in the lower parts of the pile will therefore experience a higher consolidating pressure. This can reduce the pore volume and the water content in the wet concrete, thus changing the properties of the hardened concrete. Recent research by Justs et al. (2011) has shown that even a relatively small pressure can have a significant positive effect on concrete properties such as compressive strength and stiffness. However, the possible change of concrete properties with depth is commonly ignored by foundation engineers in the current design practice."

Jan 1, 2014

By A Asadov, D Nair

This paper discusses the determination of the percentage of crystalline material in a natural silica deposit which would be considered harmful to health (<10 ¦m). A sample of the natural silica material was recovered and split into a number of subsamples. Samples were sieved using a conventional dry sieve to remove material >300 ¦m before testing. Particle size analyses of the fine fraction showed 75 per cent of the material was below 10 ¦m. Initially XRD and XPS were run on the samples to determine the minerals and composition of the sample. The XRD revealed strong quartz peaks and smaller tridymite peaks with a high amorphous background. The XPS indicated traces of iron, titanium and carbon with dominant silicon and oxygen peaks. The structure of the sample was investigated using the SEM. It was apparent that there were a number of larger quartz crystals (>30 ¦m) with a mix of amorphous and crystalline in the finer fraction. It was also observed that amorphous material was attached to the surface of the crystals. In order to determine the percentage of crystalline quartz a known amount of quartz was added to the sample incrementally. On each addition an XRD scan was performed and the area under the peaks recorded. Back analysis of these peaks with an assumed percentage of crystalline material in the original sample gave a crystalline content of 30 per cent. The quantity at the respirable fraction was estimated to be 18.7 per cent.

Jan 1, 2003

I want to explore whether it is valid or even useful to talk about sustainable corporations. After 20 years of focus on sustainable development, the concept of a sustainable corporation is not particularly helpful and it may in fact be profoundly misleading. Why? û because it obscures the need for corporations to be recognised as part of a sustainable society, rather than achieving some kind of corporate nirvana divorced from the social, political and environmental reality. It is more helpful to ask whether corporations are ready to recognise that they are one player among many within society û with the demands this would place on them in terms of transparency, accountability and social responsibility. The achievement of sustainable development has become the new corporate orthodoxy of many large corporations. It has become a clichT to argue that corporations must become æsustainableÆ. The achievement of æsustainabilityÆ is encouraged, as the ultimate step in some form of corporate evolution. We are failing to recognise that sustainability a process û not an end in itself. An enormous array of instruments is being developed to measure when sustainability is or is not being achieved. For example, corporate reporting has burgeoned into an art form, which describes æsustainabilityÆ in a variety of ways. There is no external standard applied to such reporting. These descriptions are quite partial and often place the best possible gloss on the companyÆs activities. I have become increasingly uneasy about this rhetoric and this paper has allowed me the luxury of sorting out my unease. I will discuss, largely in the Australian context, the current debate and literature and describe the way some global mining corporations are dealing with these questions, and finally, offer some suggestions which might be helpful at the operational level.

Jan 1, 2002

By Brad Thrall

"Viceroy Resource Corporation of Vancouver, B.C. has recently developed the Brewery Creek Mine, an open pit heap leach gold mine 55km East of Dawson City in Yukon, Canada. Mineable reserves are 17.1 million tonnes of ore grading 1.45 grams/tonne, containing 24.8 tonnes (797000oz) of gold. Ore processing employs the heap leach technology using run of mine ore. 1996 highlights included construction of 158,000 m2 of leach pad, placing 1.9 million tonnes of ore at a grade of 1.46 gpt on to the leach pad, construction and successful commissioning of the ADR plant, and pouring of the first gold bar on November 15th.Permitting this mine has drawn significant attention because the heap leach technology, while proven in other jurisdictions, has not been used in Yukon where winter site temperatures routinely reach -45 C for extended periods.IntroductionFollowing a comprehensive governmental and public review of the proposed project, a Class A Yukon Water license was issued in August, 1995. Construction started in 1995 and leaching commenced in October 1996. The Brewery Creek Mine is in Yukon, the home of the Klondike Gold Rush nearly 100 years ago. This is the only part of Canada not glaciated in the Wisconsin advance so there is oxide ore resulting from about 80,000 years of weathering -unique in Canada. Discontinuous permafrost is present on site and has required special consideration in the design. Winter temperatures dip below minus 50 C, demanding an approach to mining and leaching that is different than in more temperate climates.Project DescriptionThe mine comprises 8 shallow, largely oxidized gold deposits along a 7km corridor. An 8 year mining program will extract 17.1 million tonnes of ore grading 1.45 grams/tonne, containing 24.8 tonnes (797,000 oz) of gold. The strip ratio will be 1.35: 1. Overall gold recovery is projected at 78%. There will be 2.3 million tonnes of ore placed on the pad annually, with an average of 2.57 tonnes (83, 000 oz) of gold recovered per year. Because of the cold winters, the mine will operate approximately 210 days per year, while the leaching process will operate on a year round basis. Run of mine ore is placed on the heap 150 days per year. The recovery process utilizes conventional sodium cyanide leaching , carbon adsorption, caustic desorption, and on-site smelting. Peak employment during mining is 145 and winter staff is reduced to 45."

Jan 1, 1997

By K. Nielsen, J. Kristiansen

A series of laboratory blasting and grinding tests on three types of hard and competent rock (coarse-grained monzonite, fine-grained granite and very fine-grained gabbro) showed that a higher level of applied explosive energy enhanced grindability and produced a larger amount of fine (-0.106 mm) material. This confirmed reported industrial experience and the results of previous investigations. However, the results did not provide any information on the quantitative relationship between the energy applied in primary blasting and that required in subsequent comminution. Only about 1% of energy consumed in conventional grinding is used to create new surfaces, while power efficencies in cone crushers have been estimated at 70-80%. In blasting, up to 20% of explosive energy may be transmitted to the surrounding rock as elastic strain energy, leading to both primary rock breakage and the generation of microcracks

Dec 1, 1995

By J. G. Strasser

"There has been considerable output over the last three decades from the social sciences concerning man and his working environment. In the mining industry at large, however, authoritarian, hierarchical control systems remain the norm, and it can be argued that something less than optimum effectiveness in terms of both productivity and worker satisfaction has resulted.Recently (/975), Campbell Chibougamau Mines Ltd. devised a most interesting organization and incentive system that links the underground production of a standard ton of mined output at controlled grade to an incentive payment scheme. A parallel scheme in the mill complex is based on maximizing recovery of copper and gold from available feed. A key part of both minsystems is the formation of groups who have considerable autonomy, particularly when compared to the still prevalent traditional mining industry relationships between the worker and supervisory levels.This paper traces the development of Campbell Chibougamau's system . Attention is drawn to qualitative and quantitative measures of the success of the method through the commentary of those miners involved in the scheme, and by reference to the favourable records on productivity, absenteeism, safety, turnover and grievance activity.IntroductionPyramidal or hierarchical management control systems, coupled to piece-work incentive schemes, predominate throughout Canada's underground mining industry. Although specific details of such systems vary from site to site, they , are generally understood and accepted as fact by the majority of the work force.Normally, a front-line supervisor (shift boss) directs a number of workmen and assigns them to tasks and working locations commensurate with their abilities, knowledge, training and skills. This front -line supervisor may direct or supervise from as few as 12 to as many as 75 or more workmen. He issues orders according to his assigned production objectives and ensures that these directions are fulfilled in accordance with standard mine practice . Several shift bosses are usually directed by a mine foreman or mine captain. The mine captains report to a general foreman or directly to the mine superintendent or his assistant, depending on the size and scope of the operation."

Jan 1, 1981

By M. Cai

A practical simple method is proposed to estimate the tensile strength (st) of strong brittle rocks from the strength ratio of R= sc/st = 8 sc/sci, where sc is the uniaxial compressive strength and sci is the crack initiation stress in an uniaxial compression test. 8 is the Griffith strength ratio and the term sc/sci accounts for the difference of crack growth or propagation in tension and compression in uniaxial compression tests. sci can be reliably obtained from volumetric strain measurement or acoustic emission (AE) monitoring. With the strength ratio R determined, the tensile strength can be indirectly obtained from the result of uniaxial compression tests. In addition, a practical estimate of the Hoek-Brown strength parameter mi is presented and it is suggested that mi = 12 sc/sci can be applied to strong, brittle rocks in high confinement zone and mi = 8 sc/sci can be applied to low confinement to tension zones. It is found that the predicted tensile strengths and Hoek-Brown strength parameter mi using this method are in good agreement with test data. The rock strength parameters like st and mi, which require specialty tests such as direct tensile (or Brazilian) and triaxial compression tests for their determination, can be reasonably estimated from uniaxial compression tests.

May 1, 2009

By T. Backers

In fracture mechanics modeling the rock mass is seen as the combination of rock material and fractures, which are evident on different scales. The activation and propagation of fractures dominates the stability and performance issues as well as fluid flow potential. Once fractures have started to grow into each other and create through going separations, stability of rock engineering constructions may be violated. Further, as fracture mechanics inherently incorporated a scaling law in the form of the participating fracture length, scaling issues can be more accurately mirrored. This contribution highlights some examples of application of a fracture mechanics based code on some rock mechanics issues such as numerical laboratory experiments, borehole stability or the creation of fluid pathways due to underground constructions. The results show explicitly the creation of fractures and connection of existing ones, and hence the safety and performance issues. It has to be concluded that the basis for frequent application of fracture mechanics on specialized challenges in Geomechanics is laid, and the needs for future developments are defined.

May 1, 2009

By I. Alp

Application of magnetic separation was investigated for the enrichment of colemanite ores by removing the magnetic gangue fraction. The detailed XRD analysis of the ore has indicated that the gangue fraction is composed predominantly of the iron-bearing silicates such as smectite and, to a lesser extent, illite. Magnetic susceptibility measurements of the colemanite and gangue samples have proved that colemanite is diamagnetic in character whereas gangue fraction is weakly paramagnetic to allow the removal of this fraction by magnetic separation. Magnetic separation of the crushed and sized ore samples (-5 mm +75 µm) was performed using a high intensity permanent magnetic separator. Under the test conditions a colemanite concentrate (41.29 wt.% B2O3) was found to be produced from the crushed ore (30.76 wt.% B2O3) at a recovery of 96.76%. These findings suggest that magnetic separation has great potential as an alternative process for the production of a concentrate of commercially sufficient grade.

Jan 1, 2009

By Davies S. G, Mackey L. C

The oxidation of iron and nickel sulphide concentrates, and the dominant sulphide minerals which comprise them, has been studied under ignition conditions using thermogravimetry (fG). The concentrates were derived from various minesites and they showed differing tendencies to ignite. Ignition temperatures ranged from 416 to 488°C and the extents of reaction, measured at 500°C, varied from 64 to 88 percent. The reactivity of the least reactivematerial was improved significantly by grinding. Particles <63/lm showed 85 percent oxidation compared with 55 - 65 percent for particles >63/lm.Examination of the individual sulphide minerals revealed that these materials also have significantly different degrees ofreactivity and are subject to particle size effects. For particles <45/lm, the ignition temperatures were as follows:ò pyrite and violarite 380 - 385°C; pentlandite 425 - 430°C; and pyrrhotite 470 - 475°;ò for particles >90 /lm, the ignition values were: pyrite 395 - 400°C;ò violarite 430 - 435°C; pyrrhotite 540 - 545°C; and pentlandite 560 - 565°C.Using the data on the individual minerals it was possible to rationalise the differing degrees of reactivity of the concentrates. The role of the most reactive constituent in initiating the ignition reaction has also been discussed.Finally, the results of this work were found to compare. favourably with the behaviour ofthe concentrates in industrial and pilot-scale flash smelters.

Jan 1, 1989

By Roy Lindsay, Paul O'Hara, Gary Halverson

"The New Britannia Minesite is located in Snow Lake, Manitoba, 420 miles north of Winnipeg (figure 1). The mine previously operated from 1949 to 1958 extracting some 5.39 million tons of ore at a 0.150 opt gold grade. From 1959 to 1986 the property was held by Nor-Acme and Hudson Bay Exploration and Development and in 1987 High River Resources Ltd. Optioned the property, dewatered the mine and conducted a diamond drill program between the 1 780 and 2400 levels. In 1988 two companies, Nor-Acme Mines Ltd. and High River Gold Mines Ltd., negotiated an option agreement with INCO Gold whereby !NCO assumed management control of all site exploration work. During this period, a bulk sample of 10,000 tons was extracted from the 1780 level with no further exploration recorded after its removal. Both Hudson Bay Exploration and Development and INCO Gold conducted feasibility studies on reactivating the property but at a calculated capital cost of Cdn $70 to $80 million found the rate of return on their investment unacceptable.In 1991 !NCO Gold merged its interest with the assets of TVX Gold Inc. and in February 1994 TVX Gold Inc. and High River Gold Mines Ltd. entered into a joint venture partnership to develop the Snow Lake property, naming TVX Gold Inc. the operator. Upon completion of a feasibility study in April 1994 by Bharti Engineering Associates Inc., a decision was made to reopen the Britannia Mine at an established project cost of US $33 million.Project construction commenced in July 1994 with the hoist house excavation. The first concrete for the hoist house level footings was poured on August 4, 1994 and the project was completed on October 1, 1995 at a cost of US $36 million. The first gold pour took place November 4, 1995.This paper not only presents the metallurgical aspects of the operation but also describes the novel approach used to complete the design and construction of the site facilities."

Jan 1, 1996

By Roberto C. G. Oliveira, Scott C. Brown, Brij M. Moudgil

"The wettability or surface energy of particle surfaces dictates a number of multiphase ensemble interactions that have a significant impact in mineral processing. Dispersion, bulk powder handling and flotation are just a few of the processes that are largely influenced by the degree of hydrophillicity or hydrophobicity on particulate surfaces. Because of the importance of surface wettability, a number of simple, precise and accurate techniques for accessing surface wettability or contact angle on macroscopic flat surfaces have been developed. However, these techniques cannot be directly applied to the particulate surfaces that are often in query. Though a number of techniques are available for accessing the wettability of particulate surfaces, these methods are either relative, application specific or prohibitively tedious. In the present study, key features of existing techniques are combined to formulate an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.Through the use of an inert adhesive and an inert macroscopic surface as a support, it is illustrated that precise measurements of particle wettability are obtainable under suboptimal or ‘shop floor’ conditions. The measurement of the maximum external meniscus height formed between a test liquid and a particlecoated rod is employed to estimate phenomenological contact angles on particles ranging form a few nanometers to several hundred microns in size."

Jan 1, 2003

By G. Krogman, C. Walla, B. Wood

The Gebo Mining District (District) is located in the Bighorn Basin of Wyoming. Commercial underground coal mining began in 1906 with the arrival of the railroad in Thermopolis, which is located approximately 11 miles to the south. Mining in the District ceased by the early 1970’s. In Fall of 1999, Lidstone and Associates, Inc. (LA) and their subcontractors were retained by the Wyoming Abandoned Mine Land Division (WyAML) to perform an inventory of over 500 abandoned mine sites across Wyoming. During the summer of 2000 field inventory, a 30-foot deep headcut (Figure 1) and sink-hole were noted in the West Fork of Sand Draw (WFSD), immediately west of the Town of Gebo. The headcut and sink-hole were located at the culvert outfall associated with a stream crossing of a relatively well traveled county road. Upon further investigation, it appeared that underground mine workings had been exposed at this location. This resulted in a condition whereby water would be conveyed directly into the mine workings during a runoff event. The exposed mine workings as well as stream capture created a very hazardous condition. The WyAML implemented mitigation measures in the summer of 2000 by constructing a temporary stream crossing upstream of the existing failed crossing. To address this hazardous situation as well as a number of other hazards identified in the District during the field inventory, the WyAML retained PHC Reclamation, Inc. (PHC). PHC was directed to perform a field investigation and develop a Reclamation Plan to address all existing abandoned mine hazards in the District. Federal, state, and private parties own lands within the District. Hazards identified during the investigation included an underground mine fire, open adits, open shafts, subsidence, drainage problems, and coal slack. A Report of Investigation (ROI) was submitted to various regulatory agencies that documented the existing conditions and conceptual reclamation plans to remediate the hazardous conditions. After review of the ROI by the US Department of Interior - Bureau of Land Management (BLM) an on-site meeting was conducted. BLM Cultural Resource personnel declined to approve a District reclamation project until a historical overview of the entire District was prepared. Due to the hazardous situation associated with the WFSD stream crossing, Hot Springs County Road and Bridge Department convinced various state and federal regulatory agencies to allow reclamation of the stream crossing to occur. A decision was made to allow reclamation on privately owned lands within the WFSD drainage. This decision limited the amount of channel that could be subjected to reclamation upstream of the crossing to privately owned lands. PHC contracted LA to perform a geologic, geomorphic, hydrologic, and hydraulic investigation of the drainage to assist in the development of a WFSD reclamation plan. LA’s investigation consisted of four parts: Delineate the extent of mine workings in the area; Identify all drainage structures that required mitigation; Survey a series of channel cross-sections and a longitudinal profile of the impacted channel; and, Develop basin hydrology to assist in the design of a stable reclaimed stream channel.

Jan 1, 2006

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the eighth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Jefferson County, Pa., which comprises parts of Marienville, Hallton, Ridgway, Brookville, DuBois, Penfield, Smicksburg, and Punxsutawney quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals is included. Data on the coal beds in the county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information. A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick, These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By R. T. C. Rasmussen

"INTRODUCTION This is the second report of investigations describing tests in full-scale commercial heats of steel-using electrolytic manganese having a purity of about 99.95 percent, produced in the Bureau's pilot plant at Boulder City, Nev. The first report dealt with tests in cooperation with two companies can the use,of electrolytic manganese in the manufacture of stainless steel. 3/ Plans aril cost estimates for reasonably large commercial, electrolytic plants based upon pilot-plant experience, as well as the comments of a number of concerns where electrolytic manganese has been tried, are contained in another publication.4/ The tests in cooperation with industry are part of the Bureau of Mines program of investigations of methods of utilizing low-grade domestic manganese ores, thereby the United States leas dependent upon foreign sources of manganese for metallurgical use. The Boulder City pilot plant already has demonstrated the feasibility of producing electrolytic manganese from several of the most important reserves of low-grade manganese ore. As the ferromanganese normally used by the steel industry represents the bulk of the Nation's manganese requirements, the usefulness and possi¬ble advantages of electrolytic manganese in the manufacture of steel must be established if electrowinning from domestic ores is to become an important factor of manganese supply.Preliminary arrangements for the cooperative tests at the Atlas Steel Casting Co., Buffalo,. N. Y., were made with E. L. Altenburg, vice president and general manager of the company, by A. A. Dow. 5/ The data on the tests at the Atlas plant presented herein are based upon reports of E. L. Altenburg and information obtained by the author during a visit to the plant to observe the initial trial heats with electrolytic manganese in the open-hearth and the electric furnace."

Nov 1, 1945

By Vasile Pop, Ovidiu Galca, Constantin Salajan

The paper comprises a brief presentation of the rock fracturing techniques applied in CNMPN “REMIN” Company’s mines in Baia Mare. Parallel are emphasized some shortcomings of this field. The second part of the paper includes our preoccupations and achievements, of the last period, in especially those linked to techno-economical indices improvement resulting from the development of relatively large section mining works and blasting applied with sublevel caving methods.

Jan 1, 2003

By Gennaro Di Lauro, Laura Meraviglia, Demostenes Efstratiadis, Danilo Coppe

This paper presentation regards the European Union’s project “I.C.E.A. - Identification Colors of Explosives and Blasting Accessories (Agreement number – HOME/2010/ISEC/AG/071 – 30 – CE – 0447240/00-11), submitted under the call for proposal “ISEC 2010 ACTION GRANT” of the “Prevention and Fight against Crime” Program of European Commission. The main objective of the project is to simplify counter-terrorism security measures and the procedures for visual identification of blasting devices.

Jan 1, 2015

By D. M. MacHunter, M. K. Palmer

Refinement of design parameters and features has resulted in the development and commercialization of spiral separator models that offer enhanced performance for a number of application areas. Examples of recently developed spiral separator models include the enhanced performance (EP)spiral and the HC (high capacity) series. Comparative performance data for appropriate applications are presented for each of these new model spiral separators. The utilization of spiral separators providing improved performance offers significant cost and operational benefits for process plants. Examples of process flowsheet changes that have resulted from the incorporation of recently developed spiral separators include the reduction of the number of process stages and the achievement of high density tailings by the utilization of a dewatering arrangement in the spiral tailings splitter system.

Jan 1, 2003

By Michael Horn

[An economic trading region made up of 22 eastern Washington, northern Idaho, and western Montana counties, with Spokane, Washington as the central place, was defined for this study. modeling system with the, 1985 county database was to create an Input/Output based model of the regional economy. The leading ice, with respect to income, employment, value of exports, and total industry output are shown for each county and the region. The value of total industry output from natural resource based industries is also shown for each county and the region. Interindustry transactions, final demand, and value added components for the region are shown in the Regional Gross Flows Table. The total gross output for the region is valued at $36.7 billion. Total industry output for the region is $18.1 billion. The region provides $5.4 billion in income to a work force of 286,000. Spokane County, Washington accounts for about 50 percent of the regional total industry output, income, and employment. Both Spokane County and then as a whole produce about 80 percent of the total industry output for final demand with remaining 20 percent going to intermediate inputs for further production. Spokane County exports about 43 percent of its total output while 35 of the regional output is exported. Exports account for more 50 percent of the total in 18 of the 22 counties within the region. About 9 percent of the total industry output from Spokane County and 19 of the total output from resource f: .t *III For counties Spokane a industry ? N from nafural resource based represents 18 percent ?.{1 to 71 s. ?-{ and averages 39 r. ?-11 of total county +' ' 7:. FS.-f.?) If t. Natural resource it us -t for more than 50 coutny 1 s ? sass in seven counties within region.]

Jan 1, 1992

By Tristan Worsey, Nathan Rouse

The Florida legislature allocated funding for the Florida State Fire Marshal (FSFM) to review the applicability of the United States Bureau of Mines (USBM) Report of Investigations (RI) 8507 blast vibration limits with respect to Florida and its soils. The study also discusses whether the current blasting vibration limits set by statute are still appropriate, including a review of measured vibration amplitudes and frequencies, structure responses, and theoretical analyses of material strength and strains

Jan 1, 2019