Search Documents

By H. Sevim

The utilization of high sulfur Illinois coal by utility plants has been decreasing since the enactment of 1990 Clean Coal Air Act Amendment. Illinois coal producers can make their coal saleable by offering the choice of taking the combustion by-products from the utility plants and placing them in the abandoned sections of their mines. To be competitive, however, coal producers need to select an environmentally acceptable transportation-handling-placement system through which the cost-per-ton of by-product disposed can be minimized. In this paper, a few such systems are presented. The favorable operating range of each system is determined in terms of distance and tonnage. A case study is given whereby cost analysis is conducted for an underground coal mine receiving by-products from two Illinois utility plants.

Feb 24, 1997

By A. B. Cecala

Enclosed cabs have been used on surface mining equipment for many years to protect equipment operators from health and safety hazards. The surface mining and quarrying process is a highly mechanized process that generates large quantities of respirable dust. Due to economic factors, more older mining equipment is being used today than in years past. With this older equipment, it is common to observe deterioration of many components on the enclosed cabs which greatly reduce their protection effectiveness. NIOSH has performed a number of different field studies, as well as a comprehensive laboratory study evaluating various factors and parameters regarding enclosed cabs. NIOSH has recently completed a cooperative research effort with Sy-Klone International and Vulcan Materials Company to evaluate the effectiveness of a newly designed uni-directional filtration and pressurization system that brings all the clean filtered air in at the roof of the cab and extracts all recirculated air near the floor. This design provides the highest air quality to the equipment operator. Testing on this new system showed an almost 10-fold reduction in respirable dust inside the enclosed cab. The uni-directional design is easy to incorporate and should be considered for all new and retrofit systems in surface mining equipment.

Jan 1, 2009

By Rudi Toba

Several areas at the DOZ haulage were observed for the crusher’s location. Initially the new crusher designed position was west of the crusher 1, but due to concerns of the mine crack zone (deep MLZ) the crusher position moved to the south. The new crusher location is situated in a diorite rock massive between 3053 – 3079 levels, with the overall excavation of 2500 cum and dimension of 14m long, 14 m wide and 14 m high. Main Crusher chamber itself excavated by development jumbo in three lifts. Development of access to the bottom crusher was developing the same time as chambering the top crusher. The pocket of the crusher mined with vertical crater retreat system which is initiated in one time after middle slot raise. Collaboration between production and perimeter blast holes to be obtaining in control the actual cuts as per the design shape.

Jan 1, 2007

By A. N. Clay

In recent times, there has been criticism of the minerals industry over the lack of quantifiable boundaries between inferred, indicated, and Measured resources. A recent initiative through the United Nations aims to try to converge the mineral resource classification systems. Since the oil and gas industry uses a probabilistic approach to defining reserve boundaries, it is appropriate to introduce a similar statistical methodology for minerals. The Venmyn Variance Tower has been developed based upon traditional statistics to utilize historical and ongoing information in order to quantify variance of geological and chemical parameters and the boundaries and logic for quantitative mineral resource classification. It is proposed that a less than 50% variance from the mean of all sample parameters is required to achieve the classification threshold to define an inferred Resource whereas between 20-10% is needed for an indicated Resource and less than 10% variance from the mean is needed to declare a Measured Resource. These limits are similar to those used by the oil and gas industry, and it is suggested that these thresholds be adopted as an industry standard to ensure consistent quantitative reporting. While this process is intended to use statistics of an orebody to provide quantifiable and defendable boundaries, it cannot be carried out unless the geology of the mineral deposit is understood and the borehole samples can be categorized into appropriate populations for which the statistics are valid. This means that competent geologists are always required to work with and understand the implications of the Variance Tower results. This paper is intended to form the basis of a series of publications that establish a process to take mineral projects along a quantifiable and logical development path. Hence, no specific field example of the practical application of this process is given here.

Jan 1, 2012

By J. Stacey

This study was undertaken to generate a locally relevant guideline for the socio-economic aspects of mine closure for South African closure practitioners and decision makers. It should also represent a resource for interested and involved stakeholders. Mine closure, and its related post-closure social, environmental and economic characteristics, is part of the lifecycle of mining operations, given the finite nature of the ore resource. Many coal mines are anticipated to close in the next ten to fifteen years in Mpumalanga, as the epicentre of the industry shifts towards the Waterberg. Social aspects of mine closure have been historically underplayed, and under researched. Coaltech thus commissioned two studies, the first of which examined the closure dynamics of 36 mines in Mpumalanga and KwaZulu-Natal in 2006. A follow-up study (July 2007) focusing on Mpumalanga3,4 confirmed some of the results of the first study. It also contained broad guidelines for mine closure covering social and labour planning, job creation, the use of mine infrastructure, developmental incentives, and environmental rehabilitation.

Jan 1, 2010

By Susan M. Moore

Many challenges are faced by workers in lower-seam (42 inches or less) mines. The lower-seam heights confine mine workers to their knees as they perform their daily tasks such as installing roof bolts, delivering supplies, repairing belt, or cutting coal. Miners working in these lower seams often consider kneepads to be their only line of defense against knee injuries. However, healthy knees do not start and stop with kneepads. Other interventions such as changing postures, proper hygiene, and work station design may also be used to reduce mine workers? risks for developing knee injuries. Incorporating these and many other interventions into a mine worker?s ?way of life? is an important step to ensuring a long, healthy career and retirement. Keeping knees healthy is also a key aspect to reducing costs in low-seam mines as the industry battles rising health care costs, and training/recruitment of replacement workers is time-consuming and costly. Educating the workforce about the possible interventions to reduce knee injury risk is a primary objective for the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). Therefore, NIOSH researchers, along with industry and academia, developed a training package to educate the mining community about some possible interventions beyond kneepads that may be used to help decrease knee injury rates. Increased awareness and simple changes are the first steps to reducing knee injuries.

May 1, 2008

By B. R. Broekman, K. J. R. Ford

Over the last decade significant development and use has been made of a simulation model that describes the HCFeMn smelting operations in Assmang Ltd. This spreadsheet based, semi-empirical, predictive model is derived from data from the submerged arc furnaces at Assmang?s Cato Ridge, KwaZulu-Natal smelter site. Departures from the empirical base case mass balance due to changes in the ores, reductant feeds and operating parameters are accounted for by use of fundamental relationships and heuristic type ratios which are applied in an iterative manner in the model. The model performs a sequential set of calculations to iteratively converge on a fully consistent mass and energy balance solution, which predicts Mn alloy and slag output masses and compositions for a given set of feeds. 440 MWh per operating day is used as the basis of energy input. The paper describes the key model components, assumptions made and calculation approach. Added to the mass and energy balance is a cost and revenue balance, which allows prediction of the economic performance for each simulation. Substantial use of the model has been made in simulating the performance of the current Assmang HCFeMn furnaces for both smelter investigations and future production planning. The model has also been a valuable tool in the strategic analysis of the use of future Mn ores and has formed the vital link between mine ore grades (metal and slag elements) and the expected alloy output, grade and profitability. Additionally, the model has been used in benchmarking exercises to predict other Mn smelting operations with remarkable accuracy. The paper highlights some aspects of the approaches taken in using the model to benchmark Assmang?s own furnace performance and cost competitiveness with other producers. For Assmang the development and application of this modelling technology has led to transformation in understanding of the Assmang HCFeMn furnace operations and increased awareness of the potential of its Mn ore bodies.

Jan 1, 2004

By Wenquan Zhang

Based on the mining and geological conditions of Wadong Mine, Longkou City, Shandong Province, China, a viscoelastic model with proper creep parameters was established. The 3-D ANSYS was used to simulate surface subsidence, analyze overburden subsidence characteristics, and propose the rational mining and pillar widths for mining in weak rocks and under special mining conditions, and provide the policy makers scientific data for decision making on mining activities.

Jan 1, 2006

Study on Flotation of the Low-Grade Magnesite Ore

Sep 13, 2010

By E. Bakhtavar

Finding a ?practical spacing between the holes? for use of the expansive mortars is an important problem in dimension stone quarries. Objective has been to first introduce a relationship between this spacing and the dependent parameters in such a way that the required size and shape of the blocks is produced with the maximum efficiency and safety, minimum wastage, conservation of reserves and protection of environment. For this purpose, a dimensional analysis was used. On the basis of granite and marble rock types in Iran two separate relations are hence established to calculate the practical spacing between the holes.

Jan 1, 2011

The Objective: To reduce the noise generated by the exhausting air from a pneumatic roof bolting drill to a maximum of 90 decibels. Any attachment used for this purpose must be lightweight and must not cause a significant increase in back pressure. The Approach: Absorb the noise with a properly designed muffler that will permit sufficient airflow without affecting the normal operation of the drill. How It Works: The air exhausted by the drill enters the muffler through perforated disks into a resonator chamber. It then passes through a series of expansion and contraction chambers and is expelled to the atmosphere through another perforated disk. The basic muffler design for the pneumatic drill was established by using both digital computer analysis and experimentally simulated noise tests. The measured parameters used in the computer program consisted of inlet and outlet pressures, temperatures, airflows and exhaust areas. United

By K. Hanson

When done properly, benchmarking is an extremely effective tool for assessing ones performance, finding areas for improvement, and identifying strengths. However, when done improperly it can be an exercise in futility and result in incorrect observations and conclusions. A primary pitfall of benchmarking is collecting too much unreliable information. Surprisingly, the evolution of data storage and the ease of data collection are not helping with better data collection. Instead, it is just allowing one to collect more information, while at the same time inundating one with too much data. Additionally, the process of data collection can be tedious and is often times delegated to the least experienced individual resulting in unreliable and incorrect data collection and entry. Another primary pitfall of benchmarking is metrics that are cost based or poorly designed. Cost based metrics typically involve comparing unit mining costs ($/tonne). Between mines, unit mining costs are not very well correlated and have become further complicated by significant regional cost variations and mining inflation in the last years. Likewise, poorly designed metrics lead to poor benchmarking results. Examples of poorly defined metrics include: metrics that rely on information that is difficult to collect, metrics that are poorly defined, metrics which are too site focused, and metrics that measure low consequence practices.

Jan 1, 2011

By Ivan B. Cutler, Milton E. Wadsworth

Coprecipitation of anionic and cationic polyelectrolytes has been applied to floccula-tion of several mineral systems. Results obtained in a study of the flocculation of kaolinite and hematite suspensions of polycationic and polyanionic electrolytes are presented. Greatly increased settling rates were observed following precipitation of positive and negative polyelectrolytes on the surface of finely divided minerals in aqueous suspension. The ratios of polycationic to polyanionic electrolytes required to produce maximum sedimentation have been shown to correspond closely with the equivalence points obtained by light scattering studies of systems containing the positive and negative polyelectrolytes by themselves. DISPERSION of colloids has been of interest to surface chemists for many years. Flocculation studies have been employed to evaluate the limits of colloid stability. In water suspensions, colloids become unstable and flocculate when the 5 potential, the potential of the kinetic solvation sheath, falls to a value at which van der Waals forces may act to draw the particles together. This may happen through an adjustment of the pH of the suspension or by addition of a salt. Optimum conditions for rapid formation of large flocs are found in the region of minimum < potential. In addition to these well known considerations, colloids in water suspensions are known to be flocculated by certain large organic macromolecules. These polyelectrolytes in some cases minimize the 5 potential and in other instances increase the attractive forces by supplying sites for hydrogen bonding.&apos; Use of organic polyelectrolytes in flocculation of mineral colloids has increased rapidly in recent years. These materials are now recognized as indispensable aids to fluid-solid separations in many extractive metallurgical operations. They have been found to increase both the settling rate in thickeners and the filtration rate of filters. In the elucidation of the characteristics of these organic reagents as floc-culants in this laboratory, it was discovered that interaction of certain polyelectrolytes had a surprisingly good effect on flocculation of mineral colloids. Experimental Procedure: The anionic flocculants used in this study were Lytron 886 and 887, produced by Monsanto Chemical Co. Both reagents are copolymers of vinyl acetate and maleic anhydride. Lime is added to Lytron 886, whereas Lytron 887 is all organic. These reagents possess two carboxyl groups for each acetate group and are therefore anionic in character. The cationic reagents used were the Peter Cooper Co. 1-X and 2-X glues. The structures are not definitely known, but the re- agents are amines and are cationic in character. The glues were prepared in the chrome-alum form. Both types of reagents may be classified as polyelectrolytes in that they are high molecular weight polymers and ionize in water. All data presented are in terms of sedimentation rate, measured in 250-ml glass-stoppered graduated cylinders. With suitable precautions such measurements are fairly reproducible and provide a sensitive means for selecting important parameters such as PH, reagent concentration, and floc size and density. Agitation was standardized with five complete end over end cycles of the suspensions in the stoppered graduated cylinders.

Jan 1, 1957

By Org de Wet

This paper summarises the strategy for selection between a two module coal plant incorporating large, but less equipment, and a three module coal plant with more but smaller equipment. The two options were evaluated in terms of three main categories: ? Size ? size of the equipment and the effect on the process efficiency as well as the difference in physical dimensions of the plant to accommodate the larger equipment; ? Cost ? capital savings between a two and a three module plant, processing the same ROM (run-of-mine) tons per hour (t/hr); and ? Practicality ? in terms of constructability of the plant, safety of using larger equipment and maintainability of the equipment. Decisions that were taken to reduce the risk associated with size, cost and practicality on the chosen option of a two module plant will be highlighted.

Jan 1, 2006

By Sergio Neves Monteiro

In the present work, a ceramic foam elaborated with illitic clays was characterized. Properties related to density and compression strength were determined in samples fired at 1300oC, a temperature that permits the clay structure to generate and retain gases that will produce the foamy structure. The microstructure of the ceramic foam was studied by X-ray diffraction, scanning electron microscopy and mercury porosimetry. The results showed that the ceramic foam presents a bulk density of 0.38 g/cm3. The microstructure is formed by large open pores, quartz particles and vitreous phase.

Jan 1, 2006

By A. A. Toprac

The recurring problem of joint failures in ofjshore structures, coupled with the catastrophic collapse of many of these structures during Hurricane Hilda (1964), hay forced reconsideration of techniques presently used to design sfuctural joints. This paper presents results of studies conducted for this reconsiderat?on. Only right-angled T-joint,s and cross-joints where a brace was welded directly to the undisturbed surface of another tube (the chord) were considered. Tests were performed on seven T-joint and 12 oross-joint specimens of two types which were designed to give a broad but practicd range to the geometrical parameters believed to be of significance to the problem. These paramefers were expressed in dimensionless form. Each specimen of the T-joints was instrumented wirh both electrical resistance strain gauges and deflection dials. After the elastic tests were concluded, each specimen was loaded to failure by applying an axial tensile load to the brace. The cross-joints were tested to failure without measuring elastic strains. Theoretical solutions for the stresses in a cylindrical shell due to a distributed radial load over portions of its surface were numerically evaluated. The experimental results are compared with calculated values obtained using Bijlaard&apos;s and Dundrova&apos;s theoretical analyses. INTRODUCTION During the last IS years a large number of structures were built for the offshore exploration of oil both in the Gulf of Mexico and dong the Pacific Coast.&apos; In all these offshore platforms, the tubular shape was extensively used since this shape provides outstanding strength in proportion to its weight, compared to other shapes, when all directions (x, y, z) are considered. Past use of tubes was hampered because of connection details. But with the advent of welding, it became no more difficult to connect tubular shapes than to connect rolled shapes. However, some problems have been encountered in actual construction in making welded joints that are adequate and yet economical. In trying to connect tubular members, designers have used a varied number of methods; consequently, some of the joints seem to be very expensive in detail while others appear weak and underdesigned. An inspection of offshore platforms owned by different companies indicates the use of a large number of joint arrangements and configurations. Such a variety of joint types in current service indicates the wide divergence of opinion that exists on how such joints should be designed, stiffened and strengthened. Fig. 1 shows the various types of connections that have been used in practice. This paper reviews the present state of art on tubular joints of the T and cross type, and presents results of experimental and analytical work being conducted at The U. of Texas and elsewhere. It is believed that such information will be of great help to designers for the formulation of proper design procedures for joints. CONNECTION PROBLEM Recently, cracks have been observed in several welded connections in offshore structures. Fortunately, until about 1 1/2 years ago, these failures have been localized and have not resulted in the collapse of structures or loss of life. For example, one platform installed in Louisiana during 1955 in about 60 ft of water had been subjected to four tropical hurricanes. This platform successfully withstood these forces and was later removed because operations at this location had been completed. Many joint failures were observed during the removal.

By Virgil A. Marple

The primary purpose of this contract was to evaluate methods and techniques by which the size distribution acid concentration of mining-related dusts can be measured. One result has been the development of a portable, battery-operated optical particle counter/ multi-channel analyzer system which can he used to determine the size distribution and concentration of mining aerosols. One important aspect of this program has been the development of a calibration technique which relates the output of the optical particle counter to the penetration of the particles through an impactor: This results in a calibration curve in terms of the aerodynamic or Stokes&apos; diameter or the aerosol particles. Using this technique, calibrations were performed on coal, silica, Arizona road dust, potash, and rock dust (corer ore) aerosols. Another task of this program was the calibration and evaluation of the GCA respirible dust monitors (RMD) 101-1 and 301. The results of evaluation showed that the instruments were within the manufacturer&apos;s specification of ±25% of the true mass concentration up to about 15 mg/m , if the dust particles were in a size range from about 0.7 to 10 µm aerodynamic diameter. Particles smaller tan about 0.7 µm were not collected by the instrument and particles larger than about 10 µm were lose in the inlet. Other tasks included performing field studies in cooperative research programs with the Bureau of Mines personnel, development of a portable polystyrene latex generator for use in optical particle counter calibrations in the field. The incorporation of impactor classification devices on the inlets of aerosol mass measuring instruments to give mass size distributions, and a study of the density of coal particles as a function of the particle size.

Jan 1, 1977

By Harry Asche

The last 12 months has seen the construction of the first Earth Pressure Balance (EPB) TBM excavated tunnel in New Zealand on the Project Hobson sewer storage tunnel for Watercare Services Limited, with the concurrent excavation of the second EPB tunnel on the Rosedale Outfall project for North Shore City Council. Together these tunnels involve a total length of 6km and follow an 8 year pause in TBM activity in Auckland. TBM performance on these two projects is thus of significant interest as there are four major tunneling projects totaling over NZ$8B being planned for Auckland, in similar ground conditions. Auckland?s bedrock is a weak sandstone/siltstone (East Coast Bays Formation), subject to infilled paleovalleys. The geology in the region has been significantly influenced by volcanic activity; 49 volcanoes are present within 20km of the city centre. The paper describes the design and construction challenges for the projects, including TBM performance, ?sticky spoil? management, and risks associated with basalt lava flows and two paleovalleys. Watercare?s Project Hobson also saw the successful implementation of a Geotechnical Baseline Report?one of the first uses of this type of document in Australasia. Rosedale Outfall is designed for high internal water pressures with varying hydraulic flows, with the risk of exfiltration explicitly addressed.

By J. Kerr

The first stage of the development of a new modified 201-type low nickel austenitic stainless steel is described in this paper. The alloy is intended for use as a structural alloy, and so requires a yield strength >400MPa as well as acceptable weldability and toughness. The low nickel content will give a lower material cost in comparison to more conventional austenitic grades, and the processing route is required to be similar to that of Type 304 to keep the processing cost low. The base alloy was designed using empirical methods developed for stainless steel, and the properties of the base alloy were verified using a range of small-scale melts. The base alloy had a 0.2% proof strength of ~320-400MPa, and so it is planned to use V additions of ~0.15% to bring about precipitation strengthening in the hot rolled condition, so raising the alloy?s proof strength above the 400MPa minimum.

Jan 1, 2004

By K. G. Kebkal, R. Bannasch

"Because the operation of tethered underwater vehicles in the deep ocean or under drifting ice areas is very complicated or impossible, the application of autonomous underwater vehicles (AUV) is preferred or even the only possible solution. However, this implies the possibility of a direct and real-time control over all AUV functions, which is only achievable with the availability of accurate positioning/navigation and a high-speed communication link. This paper presents a flexible bottom- or surface-based solution enabling high positioning accuracy of underwater objects (harvester, AUVs, bottom nodes); specifically, a multifunctional system that combines Ultra Short Baseline (USBL) transceivers and Long BaseLine (LBL) stations deployed at a large depth. Moreover, each baseline transponder is equipped with a high-speed communication device to provide the means for real-time AUV control based on the information about its current position, e.g. navigate it with direct commands and operating its actuators and other mechanisms. Moreover a communication link with a high data rate can provide valuable visual information from the operation area.Depending on how many nodes the LBL grid comprise has, target transponder positions can be estimated with an accuracy of several to tens of centimetres. The purpose of the paper is to present the experiments with all key elements of the multifunctional Hydro-Acoustic USBL-aided LBL Positioning and Communication System."

Sep 1, 2014