Search Documents

By Ronald E. Triplett, George K. Burke, Bernard H. Voor

To accommodate larger double-stack rail cars through a tunnel, the existing active tracks were to be lowered. The tunnel is an elliptical, horseshoe-shape with concrete base support, removal of which would jeopardize the tunnel integrity, particularly since the soils beneath part of the tunnel floor included soft, saturated silt overlying rock. Grouted bar anchors combined with a SuperJet soilcrete strut replaced the existing support in situ prior to floor lowering. Close cooperation and detailed timely engineering support provided a quality project. Project design and construction, ground improvement methods, and the performance of the work are described.

Jan 1, 2001

By Kjell Karlsrud

"Abstract New semi-empirical design procedures for the determination of ultimate shaft friction and load-displacement response of axially loaded piles in clay are proposed. Hereunder also prediction of how the capacity will build up with time following the pile installation, primarily as result of reconsolidation. A main basis for developing the new procedures was detailed review and re-assessment of results from a series pile load test programs published over the past 30 years on piles well instrumented to monitor soil- and pore pressures as well as load distribution along the pile shafts. Two new alternative procedures are proposed for predicting the ultimate shaft friction; a-approach using the normalised undrained strength based on direct simple shear tests as a main correlation parameter, and ß-approach using the overconsolidation ratio, OCR. Both approaches include the effects of the plasticity index of the clay, Ip, which is shown to have an especially large impact on the correlations when Ip<25. It is recommended to use both methods in design practice, and select design values for the ultimate shaft friction that represents an average for the two methods. Pile diameter, length or stiffness, or whether the pile is open- or closed-ended seem to have little impact on the shaft friction. However, a moderate effect of pile length or flexibility on the total ultimate pile capacity comes out of the proposed t-z curves, which include some post-peak reduction. The proposed procedure for predicting the time for set-up is based on linear radial consolidation theory. The main input parameters are the insitu permeability and virgin modulus number (or virgin compression index) of the undisturbed clay. The same basic formula and correlations are applicable to both open and closed-ended or partially plugging piles.IntroductionThe design procedures presented herein are primarily based on observations and data collected in connection with “fully instrumented” pile testing programs that the author has been responsible for or has become involved with over the past 40 years, or that have been found in the literature.It was a pre-requisite for the test programs included that there were sufficient high quality soil data available to give a reliable determination of the true in-situ strength and compressibility characteristics of the clay deposits. The soil conditions range from soft NC clays with undrained shear strength down to about 15 kPa, to very stiff clays with undrained shear strength up to about 500 kPa and OCR up to 25. The plasticity index of the clays mostly lies in range 12 to 60 %."

Jan 1, 2014

By E. W. J. Thornton

During the past six or seven years extensive research has been performed on ore samples procured at the Bruns1,vick Tin Mines which is located in the south-west corner of New Brunswi.ck. This property was originally staked by Mount Pleasant Mines and they did considerable metallurgical and geological work on a small copper, zinc and tin deposit. In 1969, the property was obtained by the Sullivan Mining Group and after much geological and diamond drilling work, an entirely separate ore body \Vas located two miles south of the previous workings. The major economic metals in this ore zone are tungsten, bismuth and molybdenite, but many other metals exist as well. As the ore contains a host of different mineral species, it can be seen that considerable time WRS required to develop a practical flow sheet.

Jan 1, 1977

By Gerald A. Muson, Fremont F. Clarke

"INTRODUCTION The use of scrap mica as an industrial raw material has grown rapidly during the past two decades. Demands by various industries for ground mica for use in the roofing, paint, rubber, plastics, and wallpaper trades as well as for less extensive uses in insulation, oil-well drilling, welding, pipeline enamel, decorative material, and for other purposes exceed present (1947) supplies.A small proportion of the raw material used comes from the Black Hills of South Dakota, where casual recovery has been practiced in the exploitation of pegnatite deposits for more valuable minerals. The annual production of scrap mica in the Black Hills for the years 1939 to 1946 is shown in figure 19. 4/Although small, this production of scrap mica materially augments the incomes of numerous operators.Volume production of mica would offer attractive opportunities for obtaining steady and more economical supplies of the rare minerals as byproducts. Appreciable supplies of beryl, lithia minerals, sheet mica, tantalite-columbite, and cassiterite could accrue. Furthermore, a stable scrap-mica production would complement the production of quality feldspar, for which the Black Hills pegmatites are noted, and would help balance the economy of pegmatite mineral production.Mechanical methods of separation are requisite to production of enough scrap mica to be generally profitable. Various phases of the characteristics end treatment of mica have been investigated by the Bureau of Mines. A bibliography of these reports is appended.In 1945 the Bureau of Mines conducted pilot-plant tests to recover scrap mica by selective screening of crushed pegmatite. More recently the problem has boon studied in the Pegmatite Research Laboratory to aid in developing technological methods by which scrap mica may be separated from crushed pegmatite."

Feb 1, 1949

Airy kind of a power system is a complicated network of various electrical components, such as cables, transformers, electric machines, circuit breakers, etc. For a system to work continuously and efficiently, each of the components has to be in perfect operating condition. The failure of any of these components can cause serious interruption of the supply and may in several cases involve a lot of precious time and labor in removing and replacing the damaged equipment it may also give rise to dangerous overvoltages on the system, thereby causing a safety hazard. Any piece of electrical equipment can have two likely modes of failure. The first would be the degradation of solid insulation material due to overheating, mechanical damage or a combination of the two, In this mode of failure it is possible that If the insulation damage is not an instantaneous phenomenon (a cable damaged by severe mechanical, Stress) that a detectable leakage current will do lop prior to the faint. The fault would probably he a result of heating and deterioration of the insulation by the leakage current.

Jan 1, 1975

By L. Holappa

Ferroalloy production is an energy-intensive industrial sector with significant CO2 emissions. In this paper the current situation in ferroalloy processes is discussed from the standpoint of global environmental issues, trends and development. Progress and data of ferroalloys production are frequently compared with the steel industry, which is a closely related sector and the main user of ferroalloys. Emission factors of processes and electricity production are examined as well as possibilities and future scenarios of how to diminish CO2 emissions. As a part of this study a questionnaire was submitted to experts in the field of ferroalloys worldwide to survey opinions on the ferroalloy industry today and in the near future (2020). Eighteen questions concerning raw materials, energy, environmental aspects, by-products and economic aspects were responded to by seventeen experts, the answers were analysed and conclusions were drawn. Keywords Ferroalloys, energy, CO2 emissions, electricity, sustainability, questionnaire.

Jan 1, 2010

By J. R. Hoskins

This is the final report for Research Contract No. 00101300 (Min. 34) granted by the U.S. Bureau of Mines to the University of Idaho Mining Research Bureau. The research project is entitled "Development of Improved Ventilation Technology for Non-coal Mines and Other Underground Excavations.&apos; The duration of the project was six calendar months, from 16 April to 16 October 1970. The budgeted cost was $34,867.00 of which $31,953.00 was to be furnished by the U.S. Bureau of Mines. The sequence of reporting that follows is to state the objectives as contracted, outline the program of investigation, highlight briefly the important technological factors peculiar to vein-type metal mine ventilation, and describe the normal methods of control. This is followed by the results achieved by the survey, and an itemization of the observed deficiencies in current technology. There follows a section dealing with the adopted Federal Regulations.

Jan 1, 1970

By G. L. Oldright

In an earlier series of 15 Reports of Investigations on Smelting in the Lead Blast Furnace, experimental data were given on the operations of a custom smelter, a smelter treating rich lead products, and a smelter treating highly zinciferous charges. Five "reports" were written on each of the three types of operation, which were later compared in a summary written for the Institute. Developments in each of these types of operation in lead smelting since the last of the above reports was written have continued and have followed modifications necessitated by changes in the nature of the products received for smelting. The sintering-blast furnace-smelting plants have improved their sintering operation .and have made "2-pass" sintering a more standard operation; the richer lead feeds are diluted when marginal precious metal ores are not available to prevent fusion of the sinter cakes and to permit air to contact the sulfides. Means have been devised to make it easier to remove metallic lead from the wind boxes, but no attempts have been observed to use the D & L somewhat as an ore hearth to make more metallic lead. Except in those cases where zinc-rich lead blast-furnace slags were to be retreated in a "slag-fuming furnace," the sintering and the blast-furnace operations were so carried out that a relatively "clean," lead-poor, final slag was discarded.

Jan 1, 1949

By P. A. Neill, O&apos

The caisson foundation for Vent Building No. 6, at the southern landfall of Boston&apos;s Third Harbor Tunnel, was installed inside an unbraced concrete cofferdam 250 feet in diameter and about 70 feet deep. As a spectacular engineering feat, the cofferdam itself certainly ranks first. However, the foundation work within was no routine caisson job and made its own contribution to the state of the art. Comprised of 5 ft. diameter caissons socketed 10 to 16 feet in sound rock, it posed serious challenges in logistics, space limitations and time, requiring development of unique, purpose-made equipment. The unexpected discovery of significant depths of shattered rock overlying acceptable sound rock, along with other surprises of lesser import, compounded the problems. How these challenges were planned for, met and overcome is the subject of this paper.

Jan 1, 1994

By F. A. Penning

An experimental and analytical investigation was conducted on a recoverable pit bottom buffer. Work was conducted at the Colorado School of Mines using the U.S. Bureau of Mine-s free fall test tower. The four-sided butter, one of several designs by Cable Belt Ltd., was constructed of reinforced rubber slabs. The kinetic energy of falling weights, 1670 to 6000 lb, was absorbed by the flexure of rubber slabs loaded along their edge. A series of constant energy, 3000 ft-lb and maximum design velocity, 600 fpm tests were conducted. Static testing of the buffer established the load-deformation behavior. A large hysteresis loop plotted above and below the data published by the manufacturer. Creep was evident during; the loading Lend unloading cycle. Electronic instrumentation measured deceleration using your accelerometers; overall and intermediate movement was found from four displacement transducers; bending strains were recorded at four locations; and base reactions were measured by using four load cells. Data were recorded on tape and played back on a recording oscillograph. High speed movies were taken of all the tests. Symmetry of response and rebounds, when they occurred, were noted. From the displacement-time and load-time data, maximum decelerations were calculated by four methods and different assumptions. Good agreement was found from these approaches. Impact loads ranged from a low of 0.7 to a high of 6.1 gs. A dynamic computer model was written for the response of the buffer. Displacement-time, and acceleration-time plots show close correspondence with experimental data for the ten experiments. Data from accelerometers, displacement transducers, strain gages, and load cells are included. The computer program listing, and displacement-time acceleration-time plots are also presented.

Jan 1, 1980

By John F. McCoy

The United States Bureau of Mines (USBM) awarded a contract to Foster-Miller Associates, Inc. (FMA) to develop guidelines for designing, constructing, stocking and maintaining rescue chambers in underground mines. This report develops information and recommendations which could be used by a mine operator who desired to install a rescue chamber. Volume I covers the following major areas: atmospheric life support, configuration and construction, chamber location, power and lighting, equipment and supplies, communications, and psychological aspects and training. Volume II contains the following appendices: History of Barricading, Chamber Pressurization Considerations, Diffusional Infiltration of Gas, Compressed Air Storage, Location Examples, and Psychological Aspects.

Jan 1, 1983

The reactions between molten aluminium and cryoIite have been determined from a material balance of all components involved in the process. The interpretation of results were supported by x-ray diffraction studies of the evolved vapours, quenched electrolyte samples, and side-reaction products.The most important reaction involves the formation of both Na2F (sodium subfluoride) and chiolite in the fused electrolyte. The Na2F accelerates vaporization of the melt. Some AIF (aluminium monofluoride) may also be formed but the proportion of this is much less than for the former subvalent compound.

Jan 1, 1968

By F. M. G. Egerton

Mechanisation of mining operations is not a new concept in the world of mining. Machinery has been developed, manufactured and used for many decades in massive orebodies and coal mines, both locally and abroad. Because of their size and the huge tonnages available, massive ore bodies lend themselves very easily to mechanisation. However, little progress in mechanisation has been made in narrow tabular orebodies in South Africa. The equipment available for narrow tabular orebodies requires excavations of a size that introduce large volumes of waste dilution. Nevertheless, it is essential for South African miners to experiment with mechanisation and to find a solution to the problem. This address looks at current conventional mining methods and compares them to bord-and-pillar type mining methods. Off-reef mechanisation is also touched on. It then looks at different hybridised mining methods that are being used, i.e. a mixture of conventional mining and mechanisation. It finally looks at future prospects for mechanisation in narrow tabular orebodies.

Jan 1, 2004

By David H. Tang

Massive pillar failures were observed at two underground coal mines. The results of stability analysis using traditional pillar design formulae did not agree with the underground observations. Finite element models were used to analyze the causes and mechanisms of the pillar failures. The results were confirmed by the underground observations. Finally, the improved mine plan for each case was derived to ensure the stability of the underground structure.

Jan 1, 1990

A study of the electrolysis of PbS in molten PbCl2 showed cathode efficiencies which increased with current density at fixed sulphide concentrations, and decreased with increasing sulphide concentration at fixed current densities. The anodically produced sulphur dissolved rapidly in the melt, the rate increasing with temperature and sulphide concentration. Experiments with diaphragm cells, made to determine the relative effects that dissolution of lead and sulphur have on the cathodic current efficiency, demonstrated that dissolution of sulphur was the major contributor to the lowering in efficiency.

Jan 1, 1973

By Lloyd A. Morley

The problems associated with the presence of organic materials and of water in explosion-proof enclosures used in high voltage, high capacity applications were examined through a literature search and theoretical reasoning. Information on volatilities is presented. The conclusion is reached that explosive pressures are significantly enhanced by inclusion of these materials.

Jan 1, 1976

By A Vigar

Siliceous float sampled in the Wafi River by CRA Exploration in 1977 assayed 22 g/t Au and 89 g/t Ag. Follow up in 1979 led to the discovery of outcropping mineralisation now known as Zone A. Soil sampling in 1980 and 1982 outlined a 350 m by 400 m area of >1 g/t Au at Zone A and smaller areas at Zones B, C and D. Thirty-one diamond holes were drilled between 1983 and 1986. Elders Resources continued evaluation of Zone A under a farming agreement between 1988 and 1990. Mineralised diorite porphyry was discovered in 1990 by drilling conceptual targets 500 m to the NE of Zone A. Evaluation of this copper-gold porphyry became the main focus of exploration for the next five years and a substantial resource was outlined within a single, discrete body. A review of the paths to project development in late-1995 highlighted the need for increased resources via a second mineralised porphyry and/or an additional resource of Zone A size to make the project viable. It was concluded that the greatest immediate potential for increasing the resource inventory was at Zone A itself where the mineralisation was open in all directions. Detailed mapping and drill core logging lead to the geologic and structural models being revised in early-1996. The objectives of the 1996 drill program were to extend the Zone A resource, to test for continuity of mineralisation westwards to Zone B, to better define the controls on gold mineralisation and to delineate high-grade blocks amenable to selective mining by infill drilling and 3D orebody modelling. The last drill hole of 1996 intersected 30 m at 4.6 g/t Au from 273 m in WR147, deep in the western limit of Zone A. This intersection gave impetus to continue drill testing towards Zone B. In April 1997, hole WR154 was drilled 100 m to the west of WR147 and intersected 20 m at 8.5 g/t Au and 70 m at 11.0 g/t Au at similar depths near the diatreme contact. Drill hole WR155 was then drilled 100 m to the west of WR154 and intersected 86m at 5.7 g/t Au and WR159 drilled 100 m to the south of WR154 intersected 36 m at 9.2 and 50 m at 4.4 g/t Au. A significant zone of essentially blind, high-grade gold was discovered beneath the dipping flank of a poorly mineralised diatreme in what became known as the Link Zone. The long history of evaluation has been driven by the conviction of a dedicated team that a mineralised system of the size and complexity of Wafi with strongly anomalous gold in outcrops over the entire Mount Golpu area must contain economic mineralisation hidden within it. The keys which redefined the direction of exploration and lead to the discovery of the blind, high-grade gold Link Zone were, in our view, the critical review of the project status, detailed geological and structural studies to define clear exploration targets and the necessary funding and persistence to carry this through.

Jan 1, 1999

By Tuncel M. Yegulalp, Anuta Belova

This paper expands on the ZECA (Zero Emission Coal Alliance) technology, which is aimed at making coal a sustainable source of clean energy in the near future. The technology proposed immediate capture of carbon dioxide and other pollutants upon generation, thus alleviating their negative effects in the Earth’s atmosphere. ZECA proposes using chemical energy of coal to produce hydrogen; the latter is then used to produce electricity via fuel cells or Hyrogen-Oxygen turbines. In this study, a chemical engineering package, AspenPlus 12.1, is used to simulate the reactor (reformer) in which hydrogen is produced from methane water and lime as part of the zero emission power plant. Thermodynamic conditions, pressure and temperature, are optimized with respect to molar hydrogen production. Under the proposed conditions, molar conversion efficiency, carbon to hydrogen, of 95% is achieved. Further studies are required to model the complete power plant and to optimize it for efficiency.

Jan 1, 2005

By P J. Dailey, S L. Burchell, R F. Chiappetta

In recent years, high-speed motion picture photography has become a powerful diagnostic tool and technique to study, analyze, evaluate, and aid in blast designs. Production blasting, typically lasting less than two seconds, requires an extended time base for observation and clarification of short-lived phenomena. Information obtained from high-speed photographic analysis is categorized into two main groups.

Jan 1, 1989

By João Paulo Ferreira Santos

Neste trabalho foram obtidos nanocompósitos híbridos constituídos por nanotubos de carbono de paredes múltiplas (MWCNT) e por nanofibras eletrofiadas de nylon 6 em uma matriz epoxídica. Os MWCNT foram funcionalizados com grupamentos carboxílicos e dispersos através de ultrassom na resina epoxídica. A composição resultante foi disposta de maneira alternada com mantas de nanofibras de nylon 6 para formar estruturas compósitas na forma de sanduiches, as quais foram termicamente curadas. Medidas de resistividade elétrica das estruturas obtidas mostraram que uma percolação elétrica entre 0,05% e 0,5% (v/v) de MWCNT foi alcançada. Do ponto de vista mecânico, a incorporação de MWCNT na matriz epoxídica resultou em aumentos de módulo de elasticidade (26%) e na resistência a ruptura (19%), porém, devido a presença de aglomerados de nanocargas, a deformação na ruptura e a resistência ao impacto foram severamente reduzidas para 71% e 33%, respectivamente. Por outro lado, a adição de nanofibras de nylon 6 para formar um híbrido, mostrou-se, bastante promissora ao levar a aumentos de 8% na resistência ao impacto sem ocasionar perdas de módulo elástico, na resistência à ruptura e na deformação na ruptura.

Aug 8, 2018