Search Documents

IN concentrating mills, where several millerals are recovered for realisation in more than one product, various systems are used to express the relative economic value of the work done, and, in the hope that it may prove of use to other operators, the writer will describe a system which, in his opinion, is more complete than any other that he has seen published.The controlling factor in all mill work must be based on the economic result represented by the greatest margin possible between the realizable value of the products and the cost of obtaining same.From a mill-man's point of view these are affected by the following factors:1. Metal contents of ore.2. Grade of products.3. Recoveries.4. Working costs.The grade of ore milled is usually outside the mill-man's control, but this may exercise a considerable influence on the grade of his products, metal recoveries, and revenue per ton of ore. Higher grades or recoveries may be obtained by using a more expensive process, or by additional grinding or reagents, and the economic comparison can only be arrived at by obtaining an analysis showing the monetary value of each variation within the possible limits.In the system to be described, the value of unit variations of metal contents of the ore, grade of products and recoveries are calculated in terms of a monetary unit per ton of ore with the returning charges ruling, and any suitable metal prices. To do this it is necessary to assume what, for convenience, is termed a "standard" set of results from the mill, preferably representing about average conditions, and having calculated the effect of unit...

Jan 1, 1931

By E. H. Skinner

An abandoned mine shaft near Omar, in Logan County, W, was permanently sealed through a cooperative agreement between the West Virginia Department of Commerce, Labor, and Environmental Resources, Division of Environmental Protection, and the US. Bureau of Mines (USBM), Abandoned Mine Lands (AML) Program. An engineered shaft seal design was developed and demonstrated that featured lightweight concrete as a key material component at a wet density of about 45 lb/ft3. A reinforced concrete cap designed for 5 psi live load was placed over the shaft seal. Applicable new concrete technologies relating to a 100-yr design life were utilized to assure future integrity of the shaft seal. Waterproofing methods were included in the shaft seal design to provide protection from ambient moisture and corrosive mine waters and to increase the long-term durability of the shaft seal. All construction methods used in the field trial are fully adaptable for the mine-reclamation contractor, The USBM research objectives were to develop a broad generic design that will be widely applicable to other adit-sealing and shaft-sealing problems throughout the mining industry.

Jan 1, 2010

By Wilton Johnson

Native asphalt was produced by three companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm, R. L. White Co., Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Colorado and Utah, was mined by two firms, American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California), and Ziegler Chemical and Mineral Corp. Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation) closed its mining operation during the year.

Jan 1, 1988

By R. Dippenaar

Traditionally, iron ore has been reduced with coke in a blast furnace and the hot-metal product of the blast furnace containing carbon, manganese, silicon, sulphur and phosphorous, was subsequently refined in a steelmaking furnace. During iron making as well as during steelmaking, significant amounts of slag are produced. Two decades ago, more than 13 m tonne of blast furnace slag and 4 m tonne of steelmaking slag per annum were produced in the USA alone. It is, therefore, not surprising that many attempts have been made to re-use iron and steelmaking slags. However, these slags are not merely metallurgical waste products but, on the contrary, their compositions and physical properties are judiciously designed to optimize the operations in the respective metallurgical reactors. The variation in composition and properties of blast furnaces lags are largely determined by the gangue in the ore and ash in the coke and much progress has been made in the re-use of such slag. With respect to steelmaking slag, emphasis has in recent years been placed on hot-metal treatment before refining and ladle treatment after decarburization. The bulk removal of silicon, phosphorous and sulphur from the hot-metal product of the blast furnace by specially designed slags prior to refining in a basic oxygen furnace, has reduced tap-to-tap time, lowered cost and produced steel of much higher quality. The use of synthetic slags in ladle refining techniques subsequent to decarburization in the basic oxygen furnace has resulted in reduced hydrogen and nitrogen contents and reduced solute impurities. Moreover, inclusion shape and composition control, again by the use of specially designed slags has led to the achievement of much improved mechanical properties of the steel. In these revised process routes, slag of different compositions are produced in the variety of unit processes and hence the re-use of steelmaking slags has become much more complex. Clearly, a thorough understanding of the design and use of these different slags is a pre-requisite to the development of re-use strategies. Japanese steelmakers have spearheaded attempts to reduce slag volumes in the individual unit processes and to strive towards ‘slagless steelmaking’ by recycling slags internally. Steelmaking slag volumes have been reduced on commercial scale from about 140 kg/tonne steel to 60kg/tonne steel. Moreover, model predictions have shown that, in principle, all slag can be recycled and the phosphorous extracted to produce fertilizer. This development is of particular significance since the supply of low-phosphorous iron ores is diminishing at an ever increasing rate. Keywords: slag, environment, iron, steel,

Jan 1, 2004

By William F. Hahn

This project focused effort on three separate areas: demonstration of a low seam longwall illumination system, design of illumination systems for low coal auger miners, and an assessment of machine lighting systems for machinery used to mine low seam coal. Results indicated illumination systems can be purchased by the mine operators of low coal seams. These systems can be supplied with the equipment as a factory integrated system or can be retrofitted to the machine or longwall equipment.

Jan 1, 1982

By K. Leutwyler

The key to realistic casing stress analysis in thermal recovery installations is accurate knowledge of the temperatures involved. Much information leading to prediction of heat losses from tubing string to wellbore has been published. This .same information permits calculation of casing temperature under certain conditions. This paper reviews the basis for most of the published work, the line source solution to the diflusivity equation and examines some of its application criteria in the light of unsteady-state conditions. An alternate finite differences method is presented for correlation, and experimental data pertaining to the heat transfer mechanism in the annulus is reported. In the light of the information presented in the paper, it appears that the assumption of a line source for the tubing-wellbore system is valid even for reasonably short periods of heat flow, .such as "steam soak" operations. The empirically modified equation presented earlier matches computer derived results of the finite differences approach lor periods as short as 50 hours. Previously predicted cas ing temperatures and the associated stress levels are thus verified based on these correlative computations and the reported experimental information. Fall out from the computer output resulting in some studies of the influence of insulating cement properties on casing temperature, and experimentally studied effects of nitrogen placed in the annulus at various pressures., are described. INTRODUCTION Generally speaking, predictions of average casing temperatures have been based on an idealized model involving a centralized tubing string at uniform constant temperature radiating energy towards the casing under steady-state conditions.'. ' Heat is transferred away from the casing to the formation by unsteady-state conduction across thermal barriers consisting of cement and the mud sheath. Heat balances written on the casing permit prediction of instantaneous casing temperatures. During early periods of injection, casing temperature varies appreciably as a function of time; however, for long injection times this variation decays as heat flow from the wellbore to the formation stabilizes, and it becomes virtually negligible as conditions surrounding the wellbore become quasi-steady-state (Fig. 1). Carslaw and Jaeger -escribe a solution to the diffusivity equation for a line source (Fig. 2). A constant supply of heat is introduced into the medium from the line placed into the origin of the x-y coordinate system and parallel to the z-axis. Heat spreads outward in the infinite cylindrical solid and the temperature increase on a line going through point (x, y) parallel to the z-axis at a distance r can be predicted by: The following criterion must be considered: the Carslaw and Jaeger equation is obtained on the basis of a large

Jan 1, 1967

By Robert A. Harrow

This report documents the results of the development and installation of an illumination system for an underground coal mine Shortwall Mining Section. Also presented are the techniques used for the above ground test and evaluation of the lighting system prior to installation underground which resulted in the issuance of a Statement of Test and Evaluation (STE) from the Mine Safety and Health Administration, Technical Support, Beckley, West Virginia.

Jan 1, 1979

By Russell Clough

The Pacheco Pumping Plant is situated on the west end of San Luis Reservoir in western Merced County, California. It is designed to draw water from the reservoir and pump it into a 3,500,000 gallon regulating tank. The water then flows entirely by gravity to the Coyote Pump Station in Morgan Hill, a distance of 40 miles, where it is pumped into Anderson Reservoir. This water is used to recharge the depleted groundwater table in the Santa Clara Valley. Eventually, some of the water will be diverted to Hollister in San Benito County and to Watsonville and Santa Cruz in Santa Cruz County. The owner is the United States Bureau of Reclamation. The underground work consisted of a fifteen foot finished diameter surge shaft 250 feet deep to the crown of the pump chamber; a twenty foot finished diameter pump chamber which declined from the shaft at 14.2% for ninety feet and then ran horizontally for 180 feet; and twelve each five foot diameter steel lined intake shafts 240 feet deep which intersect the pump chamber in the horizontal section. (Figure 1) Upon completion of the pump chamber, the contractor had to dewater the existing tunnel under the reservoir, excavate the remaining fifteen foot plug, and concrete the transition. The low bidder for this contract was Underground - Continental-Heller at 414,456,000. Excavation of the open cut for the pumping plant and surge shaft began on April 14, 1983. This was performed using a Koehring 1066D backhoe, dozer, trucks, and two Cat 631 scrapers. The excavation was started at the surge shaft so that the grouting could begin

Jan 1, 1985

By G J. Corbett, T M. Leach

Approximately 42 t of mercury were produced from Puhipuhi from the late nineteenth century until the end of World War II, with no significant gold or silver production. Sinter, eruption breccias and veins, mined for mercury at Puhipuhi and essentially barren of gold, are inferred in many geological models to represent the surficial levels of adularia-sericite style low sulfidation gold-silver systems. These systems may contain economic gold-silver mineralisation at depth. Conceptual geological models have been employed at Puhipuhi in the search for buried gold mineralisation. Homestake Mining utilised a McLaughlin model for exploration from 1982 to 1987, targeting mainly the vicinity of the sinter deposits. From 1987 to 1989 BHP sought deeper structurally controlled gold mineralisation within the basement greywackes, utilising models derived from studies of Round Mountain, USA and Hishikari, Japan. Macraes Mining Company Limited have accessed the previous work and applied a conceptual geological which invokes a north-south structural control for the emplacement of high-level felsic intrusions at depth. Dextral movement on these structures associated with oblique convergence facilitated the formation of a pull-apart basin in which lacustrine sediments overlie basement greywackes and are in tum overlain by Pliocene basalts. Continued activation of the NS structures created a series of inferred NE-trending dilational structures, which are targeted as fluid upflow centres for the surficial outflows. Upflows occur as eruption breccias (e.g., Plumduff) and outflow as silica sinters (eg Mt Mitchell, Williams) which are also partly obscured by the basalt cover. Argillic alteration and mercury mineralisation occur at elevated crustal levels (eg Puhipuhi mine). Modelling from structure and alteration zonations have targeted a fluid upflow in the vicinity of Bush Hill, which was not accessed by previous workers. This target was subsequently supported by surface geology and multi-element soil geochemistry.

Jan 1, 1997

By John R. Parker

Work places of an underground coal mine are required (30 CFR 1719) to be illuminated while self-propelled equipment is used. Permissible machine mounted systems have been developed and applied satisfactorily to many mining operations. However, some low seam and thin seam equipment has been difficult to illuminate because reliable, direct current systems and compact, low output, low glare luminaires were not available. This program resulted in the design and prototype construction of compact, low glare luminaires and AC and DC power systems, particularly suited to resolving illumination problems on low and thin seam mining equipment. Design objectives were based on enhancing the prospects for thin seam illumination solutions through definition of a product which could challenge markets enjoyed by higher glare luminaires and through reduction of technical risks associated with any new product development as well as the MSHA certification process.

Jan 1, 1982

By F. A. Penning

Improved skips, with lightweight cylindrical bodies, have made a significant contribution to advancing mine hoisting technology. New concept skips of aluminum bodies with rubber lining; fiberglas bodies with polyurethane liners have been designed and fabricated for field testing at an operating mine. New design, adjustable guide rollers have shown improved ride characteristics with noticeably less wear. Major reductions have been made in stress levels and stress concentrations. Field experience has shown the practicality of the approach. Guide alignment has been measured using the Guide Alignment Measuring System (GAMS). Analysis has been applied to interpret the data. Field measurements in an operating shaft and a test tower have shown the agreement in data from GAMS and plumb wires. Reproducibility has been demonstrated. The data are useful to realign shafts, to use as s maintenance tool, and to evaluate the maximum safe hoisting speeds. The surveys are made at several hundred feet per minute and the system is self-contained. Dynamics of skip-guide interaction has been analyzed using the computer program SKIP II. The effects of speed, weight, type of guides, kind of misalignment have been studied. Resonance has been demonstrated and factors that eliminate resonance have been identified. Data from the GAMS surveys are applicable to the SKIP II program. Interaction between the hoist rope and the mine conveyance has also been studied. Computer programs and closed-form solutions are presented. Economic impact of lightweight skips is presented for an existing mine and for a new mine. Reduction in rope size has a profound effect when using a lightweight skip for the same capacity. Increased productivity can be realized by keeping maximum rope pull the same while increasing skip capacity. Examples and charts project the significant savings in capital expenditure for new installations.

Jan 1, 1985

By P. A. Plunkert, D. E. Morse, L. McCartan, J. F. Papp

The mineral sector is a fundamental part of the U.S. economy. It contributes to the real gross domestic product (GDP) at several levels — basic (mining), intermediate processing, manufacturing of finished goods and construction. The real GDP during 2004 increased by 4.4 percent. The nominal GDP was about $11.7 trillion. Housing starts were up by slightly more than 4 percent for the year. And the nation’s unemployment rate decreased to5.5 percent in 2004 from 6 percent in 2003. Interest rates continued to be low (prime rate was 5.25 percent at the end of 2004) but have risen gradually, following rising inflation.

Jan 1, 2005

By J. E. Campbell, A. W. Wesner, M. Pobereskin

This paper summarizes the results of an investigation sponsored by The Coates Steel Products Company. The objective was to determine the relative effects of certain chemical and physical properties on the wear resistance of grinding balls when grinding cement. In making this study, a number of types of balls were used in both dry and wet grinding in commercial ball mills. The radioactive-tracer technique was used in separating the test balls from the rest of the mill charge and in sorting the different types of halls that were all tested at the same time for each of the grinding operations. PROCESSING OF GRINDING BALLS In order to determine whether the properties of grinding balls, namely, composition, microstructure and hardness, can be related to the rate of wear, the halls used in this study were selected to represent various combinations of these properties. It was recognized that the mechanism of wear was not the same in the wet mill as in the dry mill. Therefore, the types of balls tested in each of the two environments were not necessarily the same. However, all of the types of balls evaluated in the dry mill were tested simultaneously for one time period, while those evaluated in the wet mill were tested simultaneously for three different time periods. All of the test balls were separated from the charge when the mill was dumped. All of the balls were of 0.940-inch diameter when charged, and all but the regular production balls were finish ground to this size to eliminate the decarburized surface layers. The steels and processing methods used, as well as the micro-structures and hardness levels of the balls, are described as follows: Regular production forged SAE 1095 steel balls were used in both the wet and dry mills. They were forged to a nominal diameter of 0.940 inch and quenched in oil from the forging temperature. Each retained a partially decarburized surface layer from the forging bar stock; the maximum depth of this layer was about 0.030 inch and the decarburization was negligible where the ball was sheared from the bar. The hardness at the surface was 40 to 46 Rock-well C in the partially decarburized area and 57 to 62 Rockwell C in the areas not decarburized. The hardened zone extended to a depth of about one-third of the radius. Below the decarburized layer, the hardened zone consisted primarily of hard as-quenched martensite with varying amounts of retained austenite. This structure changed to fine pearlite at a depth of about one-third of the radius. In order to eliminate the effect of the decarburized layer, a set of production balls of SAE 1095 steel was forged to about a 1-inch diameter, quenched in oil from the forging temperature, and ground on ball-bearing grinding equipment to a 0.940-inch diameter to remove the decarburized layer. The balls' hardened zones were similar to those in the previous set. The hardness of the finished surfaces was 52 to 60 Rockwell C. A slight amount of decarburization apparently remained after the removal of about 0.030 inch from the surface. Balls of this type were tested in the dry mill only. Another set of forged SAE 1095 steel balls of 1-inch diameter was heated to 1500 F and quenched

Jan 1, 1961

By Francis E. Federspiel

Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resource potential of the Log Cabin Saddlebag, Hall Natural Area, Horse Meadow, and Tioga Lake RARE II areas in Mono County, California. These areas, along the east slope of the Sierra Nevada, are underlain by Paleozoic metasedimentary and metavolcanic rocks of the Log Cabin Mine and Saddlebag Lake roof pendants. The roof pendants are in Cretaceous granitic rocks. Pleistocene volcanic flows cap some of the older rocks, and glacial till and outwash locally cover the bedrock. The region was eroded by alpine glaciers. Four parts of the Log Cabin Saddlebag area have moderate gold and silver resource potential. Moderate potential for gold and silver resources was identified in one part of the Hall Natural Area and low potential for tungsten and molybdenum in two other parts (fig. 1).

Jan 1, 1982

The objective of this handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface coal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. There are several portions of the handbook which should prove most useful to the inspectors. The names and locations of these portions are listed below: Survey Check List (Page 2-3) Rules for Determining if Sampling is Required (Page 2-1) List of Most Frequently Encountered Contaminants (Page 2-2) List of Candidate Contaminants and their Sampling Conditions (Table 2, Starting on page 2-5) Interpretation of Results (Page 2-16) Procedure for a, Health and Safety Inspection (Page 2-25) For obtaining information not available from the above mentioned portions of the handbook, the inspector is directed to the Table of Contents, the Glossary of Terms, and the List of Commercial Products Encountered in Surveys.

Jan 1, 1975

By Giuliana A. Zelada-Tumialan

Reduced workability and flowability of the concrete through the tremie tubes and drilled shaft reinforcement have been identified as the main causes of tremie-concrete drilled shaft concrete defects. This paper discusses two recent case studies of defective tremie-concrete drilled shafts. The defects (soft inclusions, aggregate segregation, and low concrete strength) were primarily caused by the combined effects of the tremie placing sequence, rapid concrete slump loss, and poor passing and blocking characteristics of the approved concrete mix design. The level of detail contained in the drilled shaft specifications varied between projects. However, even when the specifications incorporated several of the more recent recommendations for tremie-concrete placement, the case studies showed that typical provisions for concrete mix proportioning and placement can be further improved to minimize construction defects such as those described in this paper. Based on the findings of the case studies presented, recommendations for the development of more effective specifications are provided. The recommendations include requirements for mock-up testing of proposed concrete mix designs and evaluation of the tremie-concrete placement sequence. Performance of such testing and evaluation would greatly reduce the potential for drilled shaft defects and consequent time and financial burdens associated with them.

Jan 1, 2009

By D. J. Gilbert

As a preventive action, the geotechnical department at the mine analyzed the original topography overlying a conveyor tunnel at the mine. Several dewatering drains were installed to intercept water collecting from an old lakebed. Subsequently, 20 steel arches were installed to provide additional support in an area of tunnel where original geological mapping indicated Type IV rock. This project was completed ontime with no loss to production. Construction schedules had to be developed to half hour precision, to accommodate the installation.

Jan 1, 2011

By Conné Spangenberg

Contents ?Introduction ?Metal accounting environment ?Problem statement ?Investigations & Achievements ?Metal Accounting ?Principles ?Standards ?Audits ?Questions

Jan 1, 2005

By H Susanto, N Belluz, D Flint, A Edw

The Deep Ore Zone (DOZ) is a block cave mining operation exploiting a diluted reserve of 131 million tonnes grading 1.06 per cent copper and 0.81 g/t gold in the lower portion of the Ertsberg East Skarn System (EESS). The EESS is a calcium-magnesium silicate skarn containing in excess of 250 million tonnes of copper-gold ore, located in the Ertsberg Mining District on the crest of the Jawawijaya mountain range in the highlands of Irian Jaya, Indonesia. The EESS was discovered in 1968 where it cropped out at an elevation of 4050 metres above sea level. The Ertsberg Mining District is underlain by siliclastic carbonate and siltstone formations of Jurassic to Tertiary age. The sediments have been folded and are cut by major bedding subparallel and crosscutting structures. Intrusion of a series of igneous bodies post-dates folding and faulting. These I-type intrusions are the source for the copper-gold mineralisation found in the Ertsberg Mining District. The EESS is hosted by carbonates of the Tertiary Waripi and Faumai Formations that have been altered to calcium-magnesium silicate skarn and is situated on the southern limb of a northwest-trending syncline. The EESS is an essentially vertical tabular body with a vertical extent of at least 1200 metres and a lateral extent of up to 1000 metres. The width of the EESS averages 200 metres and locally is in excess of 300 metres. The northeast (hangingwall) contact of the EESS is a skarn reaction front in sudden contact with barren marbles. This contact coincides with a zone of localised faulting and brecciation. The EESS is bounded to the southwest (footwall) by the Ertsberg Diorite, a 3.25 Ma old intrusive. The DOZ block cave operation extends from 3040 metres above sea level to a maximum of 3388 metres above sea level, has a length of 860 metres and a maximum width of 350 metres. The DOZ is a high temperature skarn with a prograde forsterite/diopside mineralogy whose protolith is the dolomitic Tertiary Waripi Formation. The principal retrograde alteration minerals include tremolite, actinolite, serpentine, talc and chlorite. Grade is highest where bornite occurs in large dense complex intergrowths with magnetite and anhydrite. Grade has been locally enhanced in the DOZ by a late-stage pyrite-chalcopyrite hydrothermal alteration event with associated brecciation. Ertsberg Diorite along the footwall of the skarn is also included in the reserve where it is mineralised endoskarn or has been mineralised by porphyrytic or late stage hydrothermal alteration. Formation of the EESS was initiated by contact metamorphism during the intrusion of the Ertsberg Diorite with later metasomatic alteration during both prograde and retrograde phases. The bulk of sulphide mineralisation formed late in the retrograde phase. The EESS is open along strike to the northwest and down-dip with on-going exploration of these areas. Current exploration is targeting both endoskarn and porphyry style alteration and mineralisation of the Ertsberg Diorite.

Jan 1, 1999

Few, if any, reliable thermodynamic data are available for the activity of tin oxide in slags. In this work, the activity of the oxide in silica saturated iron silicate slags has been measured at 1573 K using the equilibrium Sn (alloy) + Y2O2-SnO (slag).Slag and a Ag-Sn alloy were sealed in a zirconium oxide crucible to prevent the escape of volatile tin oxide, and the oxygen pressure at equilibrium measured in situ using the zirconium oxide as a solid electrolyte. Activity of tin was calculated from known data for the Ag-Sn system and activity of tin oxide calculated from free energy data. The results have been extrapolated to predict the industrially important distribution of tin and iron between Fe-Sn alloy and iron silicate based slags.

Jan 1, 1983