Search Documents

By Jamal Rostami, Ebrahim Farrokh

Selection of tunneling method, specially the use of shielded machines for application in deep rock tunnels can be heavily impacted by presence of ground convergence and squeezing conditions. Tunnel convergence is a function of ground conditions (i.e., rock mass behavior, groundwater, in-situ stresses), size of the opening, and TBM operational parameters. The case study of Ghomroud water conveyance tunnel project in Central Iran, which is under construction using a double shield TBM, is used to examine the effect of rock parameters on tunnel convergence and hence on the need for over excavation and shield lubrication to avoid problems with the shield getting stuck. Although it is impractical to perform a continuous assessment of rock mass conditions within the shield or in the lined tunnel, results of field observations and subsequent studies show that the amount of the tunnel convergence has direct correlation with the percentage of fines and large rock fragments in the muck and TBM thrust/torque/ROP. These relationships have been examined and will be presented in this paper.

Jan 1, 2007

By J. Douglas Causey

In 1988, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied part of the 12,740-acre Blue Canyon Wilderness Study Area (OR-003-073) in order to evaluate its identified mineral resources. The study area is in Malheur County, OR, about 27 miles northwest of Jordan Valley. The study area is underlain by Tertiary welded tuff, tuff, perlite and tuffaceous sedimentary rocks capped by basalt. Jasper has been mined from several localities. Some mining has been done by hobbyists. However, the area has been covered by mining claims since 1964, with mining done by commercial operators. This region has been a source of "Owyhee picture" and other similar jaspers. More recent exploration has focused on the gold potential of nearby areas such as Quartz Mountain and Red Butte.

Jan 1, 1989

By Robert Stefanko

The following tables contain the average, maximum and minimum power parameter levels for several mining machines. Power factor is listed only for defined transducer output regions. The reasons for the undefined areas are provided in the Instrumentation Chapter. Several maximum voltage drops are included, and are computed from the no load line-to-line voltage: Again, the drops are from measurements at the low side of the load center. The machines are: Continuous Miners; F6A Alpine 76AM Jeffrey (d-c) 8CM Joy 8CM (10CM) Joy 9CM-2AH Joy loam Joy CU-43-2H Joy 2 each CM26H Lee-Norse CM28E Lee-Norse Shuttle Cars; 18SC Joy 48S Torkar (a-c) 2 - 10SC Joys input to rectifier 2 - 16SC Joys input to rectifier

Jan 1, 1973

On April 1, 1982, the Bureau of Mines and the Department of Energy entered into an Interagency Agreement to develop an enhanced computer cost model for uranium in situ leach mining. The original computer cost model contained data base information related to two regions; the Wyoming basin region and the South Texas trend area. The enhanced cost model contains additional information on San Juan Basin type deposits. This addition is significant because it expands the model's capabilites to include one of the largest uranium producing areas in the United States and developes costs related to uranium production from in situ leach mining. The data base was expanded and modified to include changes necessary for San Juan basin type deposits. These changes included, but were not limited to, state and local taxes, royalty payments, depth of deposits, drilling costs, and electrical costs. Also site visits were taken to verify many of the base case parameters. Consequently, the data base has been incorporated into the computer program and existing software was modified to provide for the additional data. Information was obtained on drilling coats and therefore the current program more accurately reflects these costs to depths of 2500 feet. This depth parameter has been expanded to include Wyoming Basin and South Texas scenarios also. Verbal communications were held with one operator in the Crownpoint, New Mexico area as well as the state regulatory agencies to help validate the expanded model. As a result of these changes, several tables have been included, summarizing changes in the new default parameters and the overall range of input parameters.

Jan 1, 1982

By H. T. Chiwaye

Risk analysis is an important step in the design of rock slopes in open pit mining. Risk is defined as the product of the probability of slope failure and the consequences of the failure, and is generally evaluated in terms of safety and economic risk. Most of the risk analysis done at present is based on the use of limit equilibrium (LE) techniques in evaluating the probability of failure (POF) of the slopes. The approach typically makes use of full Monte Carlo simulations of the limit equilibrium models, with all uncertain variables randomly varied. The number of required simulations is generally over a thousand, at times as high as 20 000, in order to produce statistically valid results of the POF. Such an approach is clearly not practical when using numerical modelling programs dueto the high computational effort required. This paper explores the impact of using numerical modelling instead of the traditional LE techniques in evaluating the probability of slope failure. The difference in the overall assessed risk, in terms of economic impact, for the mining operation is then evaluated. With numerical models, approximate methods are used in the calculation of the probability of failure instead of full Monte Carlo simulations. This paper will use a method called the response surface methodology (RSM) for estimating the POF from numerical analyses. Simple slope models were used to verify the accuracy of the RSM method by comparing the results with those obtained from full Monte Carlo simulations. It is shown that there is good agreement between the POF values computed using full Monte Carlo simulation and those obtained using the RSM method. Finally, the use of numerical modelling in the assessment of risk is shown to bring a significant difference in the result compared with that from LE methods. One of the reasons for the difference is that LE models tend to underestimate the failure volumes and hence the consequences of slope failure.

Jan 1, 2010

By R Lastra, J. A. Finch

An artificial standard material has been developed and used to examine the robustness of some of the procedures for correcting stereological bias. Different mineral liberation distributions were constructed from the standard material. The particles were mounted, sectioned and the sectioning data measured with an electron microscope interfaced to an image analyser. Four correction procedures were used and the corrected and true liberation distributions compared. It was found that the large-sections correction provided a simple, uncorrupted correction. Hill's fast approximation performed well except in cases of narrow liberation distributions; the sectioning data appeared to support the assumption that the locked section and locked particle distributions are identical. Barbery's correction performed well in most cases, having difficulty only with the very irregular liberation distribution. The PARGEN correction was able to provide a good estimate of the true amount of free material, but had difficulty in predicting the locked particle distribution

Jun 21, 1905

By Donald A. Bruce

"Abstract The Deep Mixing Methods (DMM), in their current forms, have been employed in the United States since 1986, although an earlier version had seen service from 1954. The earlier developments were strongly influenced by practices in the Nordic countries and Japan, while by the late 1980’s several DMM systems had been developed in the U.S. itself. Since then, DMM has continued its evolution, principally via the challenges of a series of large, landmark projects, but also via distinct, significant technological advances. This paper highlights the key points in the history of DMM in the U.S., and provides an overview of the different methods currently in use.In the BeginningIt is a common misconception that the history of applications of the Deep Mixing Methods (DMM) in the United States dates from 1986 when SMW Seiko Inc. — a subsidiary of Japan’s Seiko Kogyo Company — was established in the Bay Area. However, the author believes that Intrusion Prepakt Co.’s patented MIP (Mixed in Place) system had been used, albeit sporadically (about 30 projects are recorded), since 1954 (FHWA 2000, 2001). Ironically, by 1961 this single auger method had been extensively used under license in Japan for excavation support and groundwater control — by the Seiko Kogyo Company. By 1972, the original MIP technique had been succeeded by more advanced Japanese methods, involving multiple augers. Intrusion Prepakt have long since become defunct.The first systematic studies of contemporary Deep Mixing Methods in Japan began in 1967 when the Port and Harbor Research Institute of the Ministry of Transportation began laboratory testing using granular and powdered lime for treating soft marine soils. Fundamental studies continued through the early 1970’s, by which time the development of industrial scale equipment was well advanced, having its first application on a marine trial near Haneda Airport. Coincidentally, laboratory and field research also began in 1967 in Sweden (“Swedish Lime Column Method”) for treating soft clays using unslaked lime. Reportedly the progenitor was a Norwegian, Kjeld Paus, who had made observations on fluid lime columns in the U.S. It would seem that developments in Japan and the Nordic countries proceeded independently until 1975 when the technology leaders from each group (Broms and Boman; and Okumura and Terashi, respectively) presented their — very similar — findings at a conference in Bangalore, India. Limited technical exchanges ensued thereafter.Whereas the Nordic developments continued to focus on the use of dry reagents (cement and lime) and relatively light equipment compatible with operating on and in very soft clays and organics, the Japanese progressed into the use of fluid reagents (cement-based grouts) and heavier equipment for both marine and land-based projects. Thus, by 1986, there were a large number of proprietary (wet and dry) DMM systems in Japan, and a rapidly growing market already by then accounting for over 12,000,000 m3 of ground treatment."

Jan 1, 2014

By Vernon K. Garrett, Gerhard Sauer

INTRODUCTION Generations of tunneling engineers had to fight not only against bursting rock and squeezing ground but also against the destroying power of water. Intrusion of groundwater into the tunnel opening affects the stability of the tunnel support system, reduces the safety of the traffic inside the tunnel, induces corrosion of installed equipment, and provides for creeping currents at electric facilities. Aware of these problems, engineers of the Washington Metropolitan Area Transit Authority and their consultants opened the way for a new approach in sealing a tunnel. It was made possible by accepting a new method of tunnel construction scarcely applied in the U.S. before. This new technique, the New Austrian Tunneling Method (NATM), provided the basis for the successful installation of a PVC-membrane between two separated shells of tunnel lining, and the carefully directed drainage of groundwater. Beside of the economic benefits already attained by applying the NATM for tunnel construction, the Authority now saves millions of dollars otherwise necessary to maintain the tunnel during its lifetime (Garrett, 1986; Setzer, 1986). But there is a large number of leaking tunnels built according to conventional methods, some of them facing severe problems jeopardizing the safe utilization of these structures. Recently developed methods indicate that even those tunnels can be rehabilitated without extensive costs by draining and sealing them afterwards. A road tunnel in the Austrian Alps provides the scene for a major attempt to convert one of those leaking tunnels into a dry structure.

Jan 1, 1987

By Eric H. Brown

One of the best methods by which the results of accident-prevention work can be measured for any particular period is to keep an accurate record of the accident experience, which may then also be compared with the experience of others. The purpose of this report is to compare records of the salt-mining companies operating in Louisiana, and their assistance in making available their accident records is gratefully acknowledged. PRODUCTION Four companies produce salt in Louisiana -Avery Salt Co., Avery Island; Jefferson Island Salt Mining Co., Jefferson Island; Myles Salt Co., Weeks; and Carey Salt Co., Winnfield. Three of these companies operate within 30 miles of each other in the southern part of the State, and the other operates in the central part.

Jan 1, 1938

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation of a coal mine. The average thickness of coal seams mined in the United States has changed very little in the past 40 years. The first measurement of thickness of bituminous coal and lignite seams was made for 1920, when the average thickness was 5.3 feet.4/ The average thickness for later years was as follows: 1945, 5.4 feet; 1950, 5.3 feet; 1955, 5.2 feet; and 1960, 5.5 feet.5/ Table 1 includes data on number and production of bituminous coal and lignite mines classified by I-foot intervals of seam thickness mined in 1920, 1945, 1950, 1955, and 1960. Though bituminous coal and lignite are mined today from seams of exceedingly variable thickness -less than 2 feet to more than 50 feet - a large majority of the production, 62 percent in 1960, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1962

By Shigeru Nishitake

The Earth Pressure Balanced (EPB) shields designed by Mitsubishi Heavy Industries, Ltd., are recently more enthusiastically accepted by tunnel boring specialists. This company having built 1,000 tunnel shields utilizes its vast experience to resolve the problem to excavate through big boulders scattered in rather soft alluvial soil. Several types of EPB shields which can cope with large size boulders are described. Such shields are equipped with both drag bits and rolling disc cutters on the cutterheads. Previously removal of boulders has presented safety problems for workers while in the muck chamber, or venturing in front of the shield. This report describes the problem and how the equipment was modified to deal with the problem.

Jan 1, 1987

By Gary Choate

The work presented in this report represents the background activity which led to the fabrication and testing of a greenhorn and crowd limit switch system for electric shovels. The program began With a literature search and manufacturers product review to gather material as a basis for concept generation. Visits to three open pit mines provided information from operation and maintenance managers which was useful in preparing design concepts. These concepts were evaluated through laboratory tests and engineering analysis to select a final design concept. The resultant greenhorn is four separate shock absorbing pads each enclosed in a housing which bolts to the end of a dipper handle adaptor. The plungers impact against stops mounted to the saddle block. The crowd limit control is a nonmechanical device which senses the location of the dipper and makes appropriate commands to the crowd motor to insure against impacting the greenhorns. The electronic crowd limit control is redundant and indicates malfunction modes. The greenhorn prevents shovel damage in the unlikely event of impact.

Jan 1, 1983

By Stephen A. Swan

This Bureau of Mines report discusses research to analyze and evaluate extended bumper systems in order to determine the degree of protection provided to equipment operators in the event of rear-end collisions be-tween off-road rear-dump haulage trucks. The basic characteristics of rear-end collisions were determined, and a detailed analysis of the col-lision dynamics was performed to identify the magnitude and direction of impact loads, the amount of energy that must be absorbed during impact, and the major factors that affect the outcome of a collision. Separate bumper designs were developed to facilitate attachment to four 170-st-capacity haulage truck frame types.

Jan 1, 1987

By V. Yahorava

Resin-in-pulp (RIP) technology has recently often been considered for the direct recovery of base metals and uranium from dense pulps. Implementation of RIP will eliminate the requirement for any solid-liquid separation downstream of leaching and has the potential to combine the recovery and purification steps, hence reducing both capital and operating costs. The recovery of the valuable metal is expected to be higher when RIP is used, especially where the leached solids are difficult to settle or filter, and to wash. The main concerns about the use of RIP for uranium recovery from dense pulps are the impact of silica on the resin?s metallurgical performance and the operating costs that would be associated with resin loss. Although a number of resin manufacturers have been developing much improved RIP-grade resins, it is critical that the most cost-effective resin be selected. Mintek currently is doing a significant amount of work on silica fouling of RIP-grade strong-base resins in acidic leach liquors and the effect it has on the performance of the resin, including its durability. This paper describes the results of the test work done on silica fouling and its impact on plant design input data. Resin durability test work was done using various laboratory techniques, but durability was also evaluated on a relatively large scale using actual pumps, screens, and mechanical agitation. Based on the results generated, a preliminary economical evaluation was done to estimate the impact of resin loss on the overall economic viability of a specific application. Keywords: resin-in-pulp, silica fouling, resin loss, equilibrium, kinetics, elution, durability, mechanical strength, resistance to attrition.

Jan 1, 2009

By Gary Friedline

As a consequence of the Coal Mine Health and Safety Act of 1969(PL91-173), the Bureau of Mines (BOM) entered into a contract with Ocean Energy Inc. (OEI) to develop, fabricate, install, and evaluate a permissible lighting system for use on a longwall coal mining operation. The program schedule is shown in Figure 1.1. The proposed regulations are contained in Appendix A. The initial part of the program involved a survey of existing longwall lighting practices in Germany and England and an evaluation of a variety of lighting components on a mockup of a longwall mining operation that was fabricated under this program. Visits made to German and British mines uncovered major differences in lighting level requirements, permissibility aspects, size, and operating constraints which identified wide disparities and essentially eliminated from further consideration any known imported lighting devices for meeting the higher lighting levels and standards proposed for US coal mines by the Mining Enforcement and Safety Administration (MESA). The longwall mockup provided use¬ful information regarding the amount of illumination required, physical size and shape of lamps, light distribution problems, cable routing, use of connectors, signaling, glare, and other important factors unique to the lighting of low coal longwalls.

Jan 1, 1975

By R. W. Heins, N. Street

An investigation was made of the Rehbinder-Kuznetsov pendulum as an instrument to aid in the study of rock drillability and of the effect of surface active agents on rock drillability. The "critical weight", i.e., the pendulum weight at greatest sensitivity, was determined for several solids and it was shown that a change in surface environment changed the maximum value of the apparent hardness but not the critical weight, and the critical weight increased with increase of hardness of the solid used. Using silver halides as the solid material, and solutions of either silver nitrate or the appropriate alkali halide, it was shown that there is a hardness maximum at the zero point of charge of the particular silver halide. INTRODUCTION The development of relative hardness measurement by the method of damped oscillations, or what has been called the pendulum sclerometer, is due largely to the Russian workers P. A. Rehbinder and V. D. Kuznetsov and their co-workers.1,2 The apparent simplicity of the method has led to its use in a number of fields, particularly those where relative hardness has to be determined on a brittle solid. As will be shown, the simplicity of the method belies its complexities. THEORY OF THE PENDULUM SCLEROMETER The operation of the pendulum is quite simple. Make a sharp point such as a diamond, hardened steel or tungsten carbide, as the fulcrum of a pendulum, with the center of gravity of the system below the point of support. The attenuation of this pendulum is a function only of air friction, provided no fragmentation, breakage or other work is performed by the point. However, when the solid surface breaks or disintegrates under the point, and the latter penetrates the solid, part of the energy of oscillation is absorbed in the work of creating new surface, and the rate of attenuation increases. In the case of brittle solids, the point of the pendulum produces fragmentary particles, whereas the point produces plastic deformation in a plastic solid; but in both cases damping occurs. This pendulum damping is a function of the hardness or strength of the solid. Whereas a pendulum oscillating on a hard material attenuates primarily by air friction, in the case of a soft material, the points penetrate the surface of the solid, producing new surface, and the pendulum damps much faster. Thus the attenuation rate is a function of the hardness or strength of a material in both plastic and brittle substances. Russian workers initially used a single support for the pendulum, but this created many problems because of oscillation of the pendulum in more than one plane. A revised version used two points, or sometimes a prism as support, successfully confining oscillation to one plane. The version using two points was constructed and used throughout this investigation, making the recording of the attenuation as a function of time relatively easy. That both points should be in contact with the solid during the damping is implied. Rehbinder (c.f. Kuznetsov2) proposed that the hardness H as measured by this method could be expressed by a quantity which is inversely proportional to the relative initial rate of attenuation of amplitude. where H = hardness parameter (arbitrary units) a, = initial amplitude da/dt = rate of attenuation of amplitude with time. In the simplest case of damping with a constant logarithmic decrement, H can be regarded as a constant for the duration of the whole damped oscillation process. That is

Jan 1, 1966

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of copper cementation with zinc in sulphate solution. For copper concentrations of the order of 10 p.p.m., a porous, adherent deposit is formed on the zinc surface and this has a significant influence on the reaction rate. When the specific mass of deposit is less than about O· 35 mg/cm2 the surface may be considered as smooth and the rate is described by simple convective counter diffusion of zinc and copper ions through a laminar diffusion boundary layer to the deposit-solution interface. In the presence of additional deposit, the diffusional mass transfer rate is increased by increased surface roughness.The rate under these conditions is first order, with the degree of enhancement independent of further increases in the specific deposit mass. The enhancement in rateis, however, directly related to the initial mass flux and the species involved in the reaction.Preliminary work showed the same mechanism to apply to cementation from chloride solution, solutions of high zinc concentration, and cementation of copper with iron..

Jan 1, 1970

By A Webster, T Murphy

Block cave mining, in its broadest sense, has transitioned from an orebody/rock mass determined method of extraction, to a low-cost and high production mining method that may be applied to any large ore deposit. This inherently means that caving is now required in more complex rock mass conditions where assistive damage, through preconditioning, may be necessary. This requires comprehensive understanding of the geology, and its interwoven relationship with geotechnical parameters, and is made more challenging due to limited exposure in block cave mines. Limited mine development throughout the cave volume equates to a heavy reliance on drilling data in terms of observations, modelling of the mine geology, and collection of geotechnical data. This translates as increased uncertainty of geological and geotechnical models and has potential to impact significantly on the ability to make informed decisions in the design and operation of the cave mine.Modelling of cave propagation behaviour requires a complex, coupled system of draw of material, flow of material through the cave stocks, and propagation of the cave-back assisted by autogenic stress-related breakage of the rock mass, manifested as seismicity. The role of geological features in the process of cave propagation is not well understood and requires evaluation on a mine-specific basis, given the diversity of geological controls/settings of ore deposits and local variability of stress fields.Seismic monitoring systems can elucidate key geological features and domains, as heterogeneous seismogenic activity is observed ahead of the advancing cave-back. The observations made from analysis of seismic monitoring data may have potential to be used as a validation tool for numerical modelling of predicted cave behaviour in similar geological settings (eg next lift/panel).Understanding of the geological structure, at all scales, is critical to optimise the design and operating decisions made in a block cave operation. At present, intermediate-scale structure, anisotropy, mineralogy and model uncertainty may be neglected or under-represented despite their likely significant role in the mechanisms of cave propagation.Insights from an analysis of the Ridgeway Deeps block cave mine are discussed in this paper.CITATION:Murphy, T, Webster, A and Chitombo, G, 2016. Beyond rock mass characterisation – the impact of geology on block cave mining, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 861–872 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By H. P. Stüwe

HE recent papers of Aust and Rutter112 have again brought to mind the importance of certain "special" orientation relationships between the lattices of two fcc crystals on the mobility of the grain boundary separating them. No theoretical treatment of this problem has been offered till now. The only principle published so far that has given an indication why certain orientation relationships should be "special" is the counting of "coincidence sites" according to the suggestions by Kronberg and Wilson.3 The "coincidence plots" published by these authors show, for instance, that two fcc lattices rotated by 38 deg around a common (111)-axis have 1/7 of their lattice sites in common. Such an orientation relationship is also characteristic for high boundary mobility. The accuracy of the orientation relationship needed for high mobility is not too rigid. Deviations up to 10 deg from the ideal orientation seem to be tolerable as can be gathered from the experimental data.'j4 The auestion arises, then. how the density of coincidence sites will be affected by a deviatioi from mathematical accuracy. This can be checked by a simple model. Two sieves are prepared, the arrangement of the holes corresponding to lattice sites on a (111)-plane in a fcc crystal. They are placed upon each other, Fig. 1. One is kept fixed, the other is rotated around an axis pushed through one hole in common to both. The light falling through holes of both sieves is then a measure for the density of coincidence sites. If the diameter of the holes is very small, light intensity is contributed only by holes the centers of which coincide "exactly." If the diameter of the holes is rather large, some intensity will be contributed by

Jan 1, 1962

By S Henderson

The Thames gold-silver deposits are part of the Hauraki goldfield, situated within the Miocene to Pliocene calc-alkaline Coromandel Volcanic Zone (CVZ). The Waitangi vein system is one of the mineralised ore shoots in the Thames district. The Thames gold deposits are characterised by shallow level epithermal vein mineralisation with phyllic to advanced argillic alteration assemblages and abundant sulphide minerals including pyrite, arsenopyrite, chalcopyrite, galena and sphalerite. Gold occurs as electrum in association with sulphide minerals. Microprobe analyses.of sphalerite grains from the Waitangi deposit mostly range from 0.8 to 1.5 mole % FeS, although one sample contains 9.5 mole % FeS. Arsenopyrite from Waitangi yields a range from 33.1 to 34.6 atomic As (%). There is no discernible correlation between the FeS content of sphalerite and gold grade in the Waitangi deposit suggesting that gold deposition is probably not controlled by changes in temperature and activity of sulphur aS2 that control the FeS content of sphalerite. The possible causes for gold deposition are thought to be boiling, mixing and changes in pH. Sulphur isotope analyses of mixed sphalerite-galena and sphalerite-galena-ehalcopyrite samples yield a narrow range of d34SCDT values (-1.0 to 0.9 ë;n=5), whereas late spongy pyrite gives unusually light sulphur isotope values (-16.7 to -27.9 ë; n=4). The sulphur isotopic values of base metal sulphides from Waitangi suggest that the sulphur was derived from a magmatic source. However, the source of light sulphur in the late pyrite grains is not known. Preliminary fluid inclusion+studies indicate homogenisation temperatures between 173¦ and 284¦C and salinities of 0.23.0 NaCI equiv. wt % (uncorrected for C02). Vein quartz at Waitangi yields d18OSMOW values from 6.8 to 12.7 ë (n=23). The calculated oxygen isotopic composition of ore fluids is between -2.1 to 3.8 ë at 250¦C and -0.1-5.8 ë at 300¦C. Oxygen isotope analyses have revealed significant variations in d18O values with elevation and gold grades. Zones of gold enrichment coincide with a zone of variable oxygen isotope values at the top of the vein system, where boiling and/or fluid mixing most likely occurred. Oxygen isotope values varying with gold grades within the Waitangi conduits suggest that d18O values may be useful in targeting bonanza grade gold mineralisation in epithermal vein systems.

Jan 1, 1993