Search Documents

[ ]

Jan 1, 2008

By D. Turnbull, H. N. Treaftis

Precipitation of tin from Pb-Sn alloys (lead-rich) occurs by the nucleation and growth of hemispherical cells which consist of tin lomelloe interspersed in the depleted solid solution. Nucleation and growth of these cells and the tin interlamellar spacing at various compositions and temperatures have been investigated. The interlamellar spacing increases approximately as the reciprocal of the logarithm of the supersaturation ratio. For constant initial tin concentration the concentration of cell nuclei increases with decreasing temperature to a limiting temperature-independent value. The kinetic results support the view that the cell growth rote is governed by the diffusion of tin along the cell boundary. In the main, the results confirm the authors' earlier deductions, drawn from resistometric and calorimetric data, about the precipitation mechonism. IT has been shown1, 2 that tin (ß) precipitates from lead-rich (a) PbSn solutions by the nucleation and growth of cells (cellular or discontinuous precipitation). These cells consist of tin lamellae, with a spacing 1, interspersed in a depleted a solution. Reorientation of a also accompanies cell growth. The kinetics of cellular precipitation of tin from lead have been measured by resistometric2, 3 and ca1orimetric1, 3 techniques. The time-transformation isotherms (t equals time; x, volume fraction of specimen transformed) of the initial rapid precipitation, which drains about 60 pet of the tin from solution, have been described by a kinetic law having the form x = 1 —exp (—bt n) [I] where n usually has the value 3.0. It was shown" that this law and the other kinetic facts can be explained satisfactorily if it is assumed that the cells grow at a constant rate and that all the cells nucleate in a time negligible in comparison with the period of cell growth before impingement. Thus, for hemispherical cells b = (2/3)pNG3 [21 where G is the rate of cell growth in cm per sec, and N is the number of cell nuclei per unit volume. The rapid rate of cell growth at low temperatures can be accounted for"' if it is assumed that the dissolved tin drains to the lamellae edges by diffusion along the sweeping cell boundary rather than by diffusion through the a crystal (volume diffusion). For cell growth governed by cell boundary diffusion it was shown, approximately G=2(X° - X° / X° ) DBA / l2 where A equals the thickness of the cell boundary; D R, the coefficient of diffusion of tin atoms within the boundary; and X° and X, are the atom fractions of tin in the supersaturated and saturated solutions, respectively. Zener8 had already shown that, where

Jan 1, 1959

By Edmund Newton

This paper is one of a series comprising the Mineral Industries Survey of the United States, which was begun in 1935. It describes the simple methods of mining and beneficiating manganese ore, in eastern Tennessee and compares these methods with those used elsewhere in the Appalachian region. The report contains general information on manganese to give a clearer understanding of the methods and costs of mining and. beneficiating manganese ore foam a widespread deposit, an in addition presents zone difficulties normally fond in these operations. The marketing, uses, and value of manganese ore are discussed as well as the amount of capital necessary for effective operation on given scale of production, and requirements are outlines for successful operation of manganese, property in this region.

Jan 1, 1941

PolyMet Mining is developing the NorthMet property near Duluth, Minnesota. Laboratory investigations had led to the development of the PLATSOL process to dissolve in one step the base metals (copper and nickel) as well as the gold and PGM’s. To complete the pre-feasibility study, a fully integrated ten-day pilot plant trial was undertaken, comprising of: high temperature (>220ºC) pressure oxidation in the presence of 5-10 g/L chloride (the PLATSOL process), followed by solid/liquid separation, gold plus PGM’s recovery from solution, conventional Cu SX/EW and recycling of the copper raffinate to the autoclave. The concentrate tested was a NorthMet bulk flotation concentrate assaying 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t Au, 2.2 g/t Pt and 9.9 g/t Pd. Laboratory results were fully confirmed and with minor adjustments of the laboratory PLATSOL® conditions, the following leach extractions were obtained during the pilot plant trial: Cu 99.6%, Ni 98.9%, Co 96%, Pd 94.6%, Pt 96% and Au 89.4%.

Jan 1, 2001

By E. H. T. Whitten

Fundamental principles of trend surface analysis are briefly reviewed. Recent analyses of several granite masses illustrate the method of estimating the quantitative regional composition and also variation trends. Mineralogi-cal, bulk chemical, and other quantitative variates can be employed. Such results should improve gravimetric surveys (etc.) relying on correction terms based upon estimated rock composition. For the first time realistic estimates of the mean composition of rock bodies can be made with the aid of trend components. Deviation maps hold promise for delimitation of disseminated mineralized areas. Deviations comprise residual "anomalies" after removal of trend components. In petrogenetic work such deviations have been shown to reflect local influences (e.g., contamination of magma by assimilation of xenoliths or country rocks of the envelope). Similarly, mineralization should be reflected as deviations standing out from background trends. Actual examples are given. Present results largely involved projection of data onto a horizontal plane, but if sufficient data are available use of three spatial coordinates increases accuracy for prediction in "unexposed" areas. Regression analysis shows that statistical correlations between variates for regionally distributed specimens are often strong (particularly with percentage data). Hence, in preliminary surveys more easily determined variates may sometimes be employed to gain first estimates of the distribution of components more economically significant. The sampling plan is of paramount importance. Unless a suitable sampling plan is devised and adhered to rigorously during collection of the samples, all subsequent analysis is liable to strong bias and to yield spurious estimates of the truth. For a wide variety of purposes it is becoming necessary to assess the quantitative composition and variability of rock masses and mineralized zones of various types. In petrology and petrography this is something of a break with tradition, because virtually all descriptions heretofore have been qualitative. Although vast amounts of qualitative data have been compiled, little is known about the quantitative behavior of rock components. However, if variability of rocks could be understood and expressed with sufficient accuracy, there would be considerable advantage to both economic and petrogenetic problems. For example, if, on the basis of a limited series of observations, the three-dimensional geometry of a disseminated orebody (or ore-bearing formation) could be predicted accurately, it would be possible to extrapolate with confidence the structure into unexposed areas. The following example based upon the geometry of an igneous cone sheet illustrates the point. The significant rock-unit gives outcrops at a number of points on the exposed surface ABCD (Fig. 1A). Study of n exposures may enable a geologist to predict that the rock-unit is circular in form and thus indicate where the unit can be expected in unexposed terrain. Such observations are made at sites with u, v coordinates, but, if subsurface information is available at sites with uvw coordinates, it will eventually become possible to predict accurately the three-dimensional form of the rock mass. Geologic rock masses or mineral deposits are not generally as regular and symmetrical in geometric form as the body illustrated in Fig. 1A. However, even where the broad limits of a major rock mass are known, a more acute problem arises in attempting to obtain detailed quantitative estimates of its internal variability; it is difficult to predict the variability of a mass from a limited number of observa-

Jan 1, 1961

By J. M. Riley

This report summarizes Bureau of Mines experiments in purifying sulfate leach liquors, which were prepared from low-tenor beryl concentrates by modifying the Degussa process. The leach liquor was prepared from a beryl concentrate containing 2.7 percent BeO by (1) sintering the beryl concentrate with limestone in a rotary kiln at about 1,150° C. and by (2) treating the sinter first with sulfuric acid and then with water to form and extract beryllium sulfate. About 80 percent of the beryllium was dissolved. The resulting leach liquor contained 2.4 grams of BeO, 20 grams of Al203, and 6 grams of Fe203 per liter. The laboratory solution contained much more aluminum and iron than a solution derived from treating 10 percent BeO concentrate, which is the standard raw material used by industry. Tests were made to determine the behavior of the solution toward alum purification and limestone neutralization both of which were employed industrially in conventional Degussa procedure.

Jan 1, 1962

Some low grade South Australian iron ores were classified on the basis of their physical characteristics. Ores from Mount Christie and Billeroo are coarse grained mixed ores; Mount Christie ore could be concentrated by gravity or dry magnetic separation at 10 mesh, but Billeroo ore needed to be crushed minus 36 mesh. Ores from Razorback Ridge and Wilgena Hill are fine grained mixed ores; ore from Wilgena Hill could be concentrated by flotation, but poor results were obtained on Razorback Ridge ore. Malcolm Creek ore is non-magnetic and crystalline, and can be concentrated by flotation, but the deposit is small. Ores from Grants Quarries and Peeralilla Hill are nonmagnetic and earthy and could not be satisfactorily concentrated.INTRODUCTIONThe Geological Survey of South Australia has for several years been undertaking a systematic study of the iron ore resources of the State (excluding the Middleback Ranges) in relation to their geology, reserves, and beneficiation. As part of the latter phase of the investigation samples of the ores have been submitted to The Australian Mineral Development Laboratories (AMDL), and it was the study of these samples which provided the material for this paper.The mineragraphic and metallurgical work was undertaken by several officers of AMDL and the results are contained in unpublished reports submitted to the South Australian Department of Mines. Field data published here was obtained from unpublished reports by G. F. Whitten, Senior Geologist, Iron Exploration, of the Geological Survey of South Australia.

Jan 1, 1964

By Paul J. Axtell

Self-hardening cement-bentontie (c-b) slurry walls were constructed as shear walls to stabilize the downstream slope of Tuttle Creek Dam near Manhattan, Kansas. The slope stabilization was required to protect the existing pressure relief well system located at the downstream toe of the dam. The wells require protection from slope deformation induced by liquefaction of the foundation sands during or immediately after the design seismic event. The shear walls are transverse to the axis of the dam, unreinforced, and relatively brittle members that may be exposed to relatively large shear strains, and possible cracking, during or immediately after shaking. An extensive laboratory investigation was conducted on recovered core samples to optimize the mix design and stabilization scheme. Furthermore, as is the topic of this paper, a portion of the laboratory investigation was to determine the large-strain, or post-peak, shear strength of the c-b material for use in limit-equilibrium slope stability analyses and numerical deformation modeling to assess the magnitude of permanent deformation caused by the design earthquake. These data may be beneficial to other projects that are considering the use of unreinforced c-b slurry walls for seismic retrofit purposes.

Jan 1, 2010

The 21st Annual American Mining Hall of Fame Awards Banquet sponsored by the Mining Foundation of the Southwest will be held at the Sheraton Tucson Hotel in Tucson, AZ on Saturday, Dec. 6, 2003. This year’s inductee, guest of honor and featured speaker at the banquet will be Thomas J. O’Neil, recently retired president and chief operating officer of Cleveland Cliffs Mining. Prior to Cliffs, O’Neil spent 10 years with Cyprus Minerals. He was also professor and head of the Department of Mining and Geological Engineering at the University of Arizona. As representatives of mining heritage, the Hall of Fame will induct James Boyd and Thomas F. Walsh. Walsh discovered a rich gold telluride vein in Ouray, CO, which became the Camp Bird gold mine. Boyd was a former director of the U.S. Bureau of Mines, vice president of Kennecott Copper and later president of Copper Range.

Jan 1, 2003

By J. A. Herbst

During the last decade it has been established that conventional flotation control strategies based on classical control theory result in significant increases in grade, recovery, and operating-cost savings. In the current report a description of an advanced model-based control philosophy is presented. The derivation and verification of a simplified flotation model is described. The implementation of a Kalman filter for estimation of unmeasured variables for input to controllers is discussed. Several control strategies using the model-based approach are described, emphasizing the nonlinear nature of the flotation plant. Expected trends in the implementation of such model-based flotation control strategies in the future are discussed.

Jan 1, 1986

Electrochemical measurements are presented on electro-deoxidation of silica in molten calcium chloride at 900°C, with porous silica pellets as starting material. Measurements during pre-electrolysis (to remove water from the melt) showed electrochemical noise, which is consistent with the evolution of hydrogen. Throughout, the dominant anodic reaction appears to be CO2formation, based on the observed potential at the anode, and measured anode wear. Because of the presence of dissolved CaO in the melt, some of the CO2 candissolve in the melt; the resulting calcium carbonate formation was confirmed by electrolyte analysis after reduction runs. Reduction of dissolved CO2 at the cathode is likely to contribute to the background current during the reduction process. For the electrode and cell configuration used here, most of the over potential arises from polarization of the anode, and ohmic potential drop in the electrolyte.

Jan 1, 2006

By John D. Bardill

Data from extensive tests was obtained on friction-head losses of various sand slurries, composed of materials of different specific gravities and under varying transport conditions, to provide useful information for designing hydraulic transport systems. The tests were run in a pilot plant through 2-, 3-, and 4-inch lines with slurries composed of relatively pure barite and limestone solids. Available grinding and classification equipment did not permit attaining a comparable size distribution in the two materials tested, thus preventing direct correlation of friction-head loss values to physical properties or mineral composition. A total of 495 measurements were made of limestone slurries in the 2-, 3-, and 4-inch pipe test sections at flow velocities from 6 to 14 feet per second and pulp densities from 40 to 70 percent solids. A total of 640 measurements of barite slurries were made in the 3-and 4-inch pipe test sections at flow velocities between 7 and 14 f.p.s. and pulp densities ranging from 40 to 80 percent solids.

Jan 1, 1962

By David Winter

The geotechnical design, construction, and monitoring aspects of a tied back excavation 85 feet deep in Seattle, Washington are presented. The excavation was completed in overconsolidated deposits of sand, silt, and clay. Lateral soil pressures used in shoring wall design were the lowest to date for an excavation of this size in Seattle. Instrumentation data collected from hydraulic load cells and inclinometers were analyzed and are discussed. The data suggest the actual soil pressures felt by the wall were lower than the design values. Recommendations for future study, as well as future design modifications are given.

Jan 1, 1987

"SUMMARYThe K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6 1/2 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,016 barrels of 43° A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive.Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949.The K.M.A. structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume c 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oilIn that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 at which pressure 1 barrel of stock,tank oil contained 525 cubic feet of gas in solution.A serious decline in reservoir pressure during the 2 years of rapid development alarmed the operators and caused them to consider a cooperative pressure-maintenance program. In the latter part of 1939, the K.M.A. Pressure Maintenance Association was organized, and the gasoline plants in the field agreed to process the wet gas and return the dry gas to leases having gas-injection wells. Approximately 27 percent of the cumulative volume of produced gas had been returned to the reservoir by August 1, 1949."

Jun 1, 1952

By J. T. McLendon

As part of its research project in developing improved refractory materials for metallurgical applications, the Federal Bureau of Mines obtained hot modulus of rupture data at 1,500°,1,550°, and 1,600° C on samples of 13 refractory periclase materials produced from seawater, lake brines, and natural magnesite. The periclase samples also were characterized to establish chemical and mineralogical composition and microstructure. The results indicated that a high MgO content does not necessarily assure good hot strength and that an optimum and varying CaO-Si02 ratio exists for each individual periclase sample.

Jan 1, 1979

By Leslie C. Richards

The competitive position of producers of industrial minerals depends upon the delivered price of their product. Freight charges are a major factor in the sales to consumers. A comparison of freight rates on movements of limestone and silica rock in the Pacific Northwest shows a wide variance in mills per ton mile for like hauls, thereby favoring some localities over others. Introduction: Sooner or later the potential miner of industrial minerals reaches the conclusion that of the various factors he must consider, the marketing of his product is. the most important. The sooner he realizes this the better, as successful industrial mineral producers .will confirm. Herein lies a difference between i.ndustria1 mineral mining and metal mining. Often in the latter, technical problems of mining or concentrating are equal to or even surpass those of marketing. This is not meant to imply that there are no problems in mining and beneficiation of industrial minerals, but these usually are outweighed by the problem of marketing. Recentlv. an official of a nationally known corporation :i the elecl.ro-metallurgical industry made an industrial mineral survey in the Pacific Northwest. In the course of his investigation he interviewed producers and potential producers of the various industrial minerals scheduled for use in the plant now being constructed in this area. He stated that he was interested in only three factors: namely, (1) Can your product meet our specifications? (2) Are you able to supply our tonnage requirements? and (3) What will be the delivered price? If there are several sources of supply of sufficient grade and tonnage, as is often the case in the Northwest, then the third factor becomes the important and deciding one. While industrial minerals are usually sold f.0.b. cars with the freight being paid by the buyer, it is the delivered and riot the f.0.b. price that determines the competitive position of the producer and his industrial mineral product. Unfortunately for both the consumers and producers of industrial minerals in the Northwest, the sources are generally a considerable distance from the markets. This necessitates long rail hauls, for which transportation charges make up the largest share of the delivered cost and the delivered price of the product. Is it any wonder then, that rail rates play such an important part in the marketing of industrial minerals? In order to sell his product, the producer must be able to deliver to the market at a competitive price. It must be remembered that his largest cost factor is rail transportation, and that he is limited to markets that he can reach competitively. Since the cost of rail transportation is so important, let us compare various freight rates in the Northwest and attempt to determine their influence on marketing. A study of all rates on all industrial minerals transported in this area, is beyond the scope of this paper. For the purposes of comparison, let us consider limestone (broken, crushed, or ground), and silica rock. These are widely used industrial minerals, and are carried by several different rail routes from.the sources of supply to the centers of consumption in the Pacific Northwest. Markets and Sources of Supply: Limestone has a number of uses in western Oregon and Washington. Among them are agricultural lime for the soils of the Willamette Valley and southwestern Washington; paper rock for the mills in such cities as West Linn, Oregon City, Newberg, St. Helens, and Salem, Oregon, and Camas and Everett, Wash.; chemical and metallurgical-grade limestone for the metallurgical plants centering around Portland, and the Tacoma-Seattle areas'; and sugar rock for the sugar refineries at Toppenish, Wash., and Nyssa, Oregon. Since limestone for cement manufacture is generally processed near the quarry, transportation

Jan 1, 1951

By H. M. Cooper

Many analysts have had difficulty in obtaining accurate and consistent determinations of the volatile matter in low-temperature coke when the usual standard method for coal was followed. The tendency is toward too-high results, due to mechanical losses which are extremely difficult to avoid or control. With cokes there also may be an error due to excessive oxidation of the fixed carbon. Much of the earlier experimental work on the volatile-matter determination in coal, such as that of Parr,5 Fieldner and Davis,6 and others, 7 has been on the effect of time, temperatures, shape and size of crucibles, method of applying heat, and type of furnace, all of which data has evolved the present A.S. T. M.8 standard method for volatile matter in coal and coke. It is not the purpose of this investigation to deal directly with the above phases of the procedure, but rather to study some of the factors affecting she results in those types of fuel which give erroneous results due to mechanical losses.

Jan 1, 1932

By W. Bullen

A hypothetical economic model has been developed for diamond projects in the Canadian Arctic using data from recent exploration and mining projects. The model reflects economic conditions applicable to the diamond mining industry in the Canadian Arctic at the present time. The economic model captures pre-production expenditures, production data, and post-production costs. Before- and after-tax cash flows are derived from the data along with the relevant economic criteria. From the corporate perspective, the model provides guidance concerning the minimum size and/or in situ value per tonne requirements of targets being sought in order to ensure economic success and predict exploration and development expenditures. From the government perspective, the model provides an indication of income and mining tax revenues that can be expected from a particular diamond project. The model shows, on average, diamond projects in the Canadian Arctic are expensive to explore for and develop, but are economically robust under the present conditions. They generate great economic return for mining companies and significant amounts of tax revenue for governments. The fact that diamonds can be transported directly from the minesite by air makes them particularly attractive targets for mining companies that operate in the Canadian Arctic.

Jan 1, 2006

By Detlef Ehlert

In view of the increasing level of cost pressure on the part of plant owners, optimized plant operation with top product quality and maintenance costs is indispensable. Unscheduled shutdowns with increased repair costs and production downtimes are significantly reduced by preventive maintenance and the stock-keeping of spare parts. To remain competitive in the steel market, it is important for plants owners to operate their plants with the highest possible degree of energy efficiency and at high availability in order to manufacture high-quality products. Plant Monitoring Systems make it possible to optimize the manner of production. An integrated overview of the overall process, under consideration of process stability, product quality, production costs and plant availability ensures a “transparent plant”.

Aug 16, 2017

By John K. Alley

Despite the extensive use of fluorphlogopite, investigators do not agree as to its exact melting temperature. Data on other fluormicas and on related fluorsilicate systems are largely nonexistent. A knowledge of the melting temperature is necessary for the effective synthesis and use of fluorphlogo¬pite or other fluormicas. The increasing use of two- and three-mica systems to yield polycrystalline ceramics has made more urgent the need for melting temperature information concerning these other fluormicas. This report is part of a program by the Bureau of Mines to synthesize large-size or large-crystal fluorphlogopite and develop a usable reconstituted fluormica sheet. The melting temperature of fluorphlogopite, K2Mg6A12Si6020F4, was found to be 1,383° ±2° C. This temperature was found by studying single crystals of fluorphlogopite, heating behavior of glass of fluorphlogopite composition, and the actual crystallization of fluorphlogopite from a melt that had been heated above 1,430° C. The formation of forsterite or norbergite was directly proportional to the loss of volatiles during the experimentation. Many trials revealed that the only reliable seal was a thick platinum sheet with welded seams. If no volatiles were lost, neither norbergite nor forsterite were formed; fluormica was then the only product. Excellently formed crystals of forsterite with an optical sign different from ordinary forsterite were obtained during the single crystal melting experiments. These crystals resulted from a slow loss of volatiles. A congruent melting of fluorphlogopite is indicated by the data of this report; however, incongruency within a small temperature range is not precluded. A more refined method using phase equilibria-quench methods would be necessary to settle the question absolutely.

Jan 1, 1962