Search Documents

By Orr C. W

In previous papers (1, 2), the influence on the creep resistance of elements normally found in commercial lead has been recorded. The results in the present paper refer to the influence of calcium, an element which is not found naturally in lead, but which has been used commercially in the form of alloys. It was realised that calcium would act as a deoxidising agent for lead-and in fact it was with this feature in view that both calcium and magnesium were used as additions. Subsequent work (including the results given in the present paper) has tended to diminish the importance which at first seemed to be associated with the presence of oxygen in lead. The structure of the dilute calcium lead alloys has been worked out in detail (S) and the phase diagram shows the existence of limited solid solubility and a compound CaPbs.

Jan 1, 1938

By J. I. Mathis

"The failure that was utilized for developing this model was a double bench-scale failure, approximately 20 m in height, in the Misery pit at BHP Billiton’s EKATI mine site. The bench that failed was excavated in biotite schist. Due to previous problems with bench-scale toppling failures, this bench was excavated with a 70° inclined, 30 m deep preshear. Upon exposure, the wall was very clean with half-barrels commonly observed from the pre-shear operation.In August 2003, a bench failure of about 1000 t occurred in this pre-sheared biotite schist (Fig. 1). Upon examination it was noted that the foliation that paralleled and dipped at 70° into the face when excavated was approximately horizontal at the top of the failure (Fig. 2). While the failure mode itself appears complex, the failure was apparently driven by three factors:• a low-angle, low-frictional strength fault or discontinuity at the base of the failure area;• water either contributed meteorically from precipitation and/or from permafrost melt; and• foliation planes providing a viable toppling geometry once toe block motion began to occur.The above details are illustrated in Figure 3.After considerable thought and analysis, a model was postulated for the failure.It is thought that the entire failure had been triggered by displacement of a toe block (Fig. 4). This toe block is bounded on the back by foliation, the bottom by a low-angle, lowstrength fault, and the front by the bench face. Water pressures behind the bench face developed forces on the block as can be seen in Figure 5. These forces were sufficient to induce block motion. As can be seen in the relative shear strength diagram in Figure 6, only a small amount of water is necessary in the face to initiate block displacement. Note that in this figure, a simplistic piezometric pressure distribution was assumed."

Jan 1, 2004

Were it simply a matter of extracting tin from the simple tin sulphide, the proposition would undoubtedly be simple enough. When, however, other valuable metallic sulphides are combined with the tin, and it is required to separate these intomarketable products, then the proposition becomes somewhat complex, and such is the case with the class of material of which I am about to write. The locality where it occurs is Howell, New South Wales, and chiefly at the Conrad Silver-Lead Mine. The tin sulphide occurs chemically alloyed with copper, iron and other metals associated with galena, pyrites, mispickel, blende and silver sulphide in varying proportions, and generally in a gangue of highly crystallised quartz.Several varieties of tin sulphides occur, and from the following analyses of three minerals, these being specimens specially selected free from foreign matters, it will be seen that the chemical composition is somewhat complex.

Jan 1, 1902

By Doris M. Hyde

The economy of Belize continued to show a very slight but still positive growth during 1986. The gross domestic product (GDP) was estimated to have been about $164 million,2 almost the same as those of 1984 and 1985. Foreign investors looked favorably on Belize because it had remained isolated from the sometimes turbulent political and social strife elsewhere in Central America. Reportedly, in late 1986, Guatemala had decided not to pursue its claim to Belizean territory and to give full recognition to that country. Discussions were to be held regarding any matters of mutual concern. New investment possibilities were oriented toward agriculture or manufacturing endeavors. Except for some interest in petroleum exploration, the minerals sector remained limited to the quarrying of construction-related materials.

Jan 1, 1988

By Brian R. Zuckerman

The Capitol Area East End Complex is currently being constructed under contract with the State of California Department of General Services on two sites adjacent to the grounds of the California State Capitol Building in downtown Sacramento. The complex will consolidate the headquarters of the Departments of Health Services and Education, which currently occupy several facilities located throughout Sacramento. When completed in 2003, the complex will be the largest civic office project in California history, with approximately 1.5 million square feet of office space and housing nearly 6,300 state workers. The total project is being constructed on five separate blocks in downtown Sacramento, Blocks 171 through 174 and 225. Separate design/build contracts were executed for the construction on Blocks 171 through 174 and the construction on Block 225. The scope of this paper is limited to construction on Blocks 171 through 174, which comprise a square, two blocks on a side, bounded by 15th, 17th, L, and N streets, located immediately to the east of Capitol Park and the State Capitol Building, as pictured in the image shown below.

Jan 1, 2002

By Terry W. Mellors, Robert J. F. Goodfellow

The underground industry has been forced to reconsider risk management sincethe introduction and implementation of the “Joint Code of Practice for Risk Management of Underground Works in the UK” published in 2003 and the subsequent international version published by the ‘International Tunneling Insurance Group’ (ITIG) in January 2006.What does this mean for major tunnel projects in the US and elsewhere? The discussion will highlight the implementation of the Codes to date, risk management principles embodied in the Codes and the use of risk registers as a projectmanagement tool and the management of risk.

Jan 1, 2007

By Randall M. Wheeler

Many of us have used a seismograph to measure peak particle velocity and frequency. But do we really understand why? Also, why do we measure particle velocity instead of displacement and/or acceleration? What is the vector sum? How do these items relate? Where does frequency fit in? This workshop will attempt to answer these and other questions. Some of the answers may surprise you, others may not.

Jan 1, 1997

By Rudi Podjadtke

In a short chronological review the development concepts and improvements in steel roadway support are shown. The successful standardization concept of RAG Deutsche Steinkohle and currently used support systems are important topics. The history of optimizing the material properties for the steel arch support with different alloys up to the tempering used today is discussed. The present-day application of the steel support is additionally presented. Today, it represents a system component of modern roadway support also for highly stressed roadways. In addition to the yielding roadway arch support, this overall system - the combination support - consists of the additional components of a rockbolting system and concrete backfilling. The comparison of the application areas for each individual partial system with the overall system illustrates its high performance capability. Actual practical experience with the state of the art typed steel arches are pointed out exemplarily. Understanding the complete system permits the selection of the economically optimal support for all conditions.

Jan 1, 2008

By Shamsher Prakash

Equivalent spring constants for analysis of footings is a function of Young's modulus of pile material (Ep), shear modulus of soil (Gs), and geometry of the footing and/or piles. Shear modulus is strongly strain dependent in soils. Therefore, the spring constants are strain dependent, which is acceptable to the Geotechnical engineers. However, structural engineers prefer to use spring constants as a function of displacement, rather than strain. In order to develop these relationships, appropriate relationships between strain and displacement are needed. Also, modulus degradation with strain needs be built into these relationships. Description of spring constants kx , ky, and kz in x, y, and z direction and k?, k?, k?, about x, y, and z directions are relatively simple. However, description of kxø and ky?, the cross-coupling spring constants depend on 2 - components of displacement and rotation. Thus, there are 8 spring constants and likewise there are 8 damping constants. Approximate strain-displacement relationships on which displacement dependant k's and c's are based are presented with appropriate equations, and a numerical example is included illustrating k's and c's as functions of displacement.

Jan 1, 2002

By Mills R, Shannon W. T, Finch J

As an extension to investigations into methods of upgrading the Iitania content of ilmenite concentrate from beach sands using 100 g/day, a small pilot plant treating 23 kg/ day of ilmenite was used.In the pilot plant the iron oxide in the ilmenite was reduced to iron at 1200°C using carbon (coal/char) without melting the material, using a tunnel kiln heating cycle, the charges contained in saggars, The iron was then separated from the titania fraction by ball milling, wet magnetic separation, and screening. The resulting magnetic product was high in iron (about 80 per cent Fe) and the non-magnetic product high intitania (about 70 per cent TiO2).From this trial sufficient data were obtained to enable the preparation of a flow sheet for a plant producing 62,300 tonnes/year total products, and an estimate of costs to be made. This has shown that for an estimatedcapital expenditure of nearly $6,000,000 and annual production costs of about $4,000,000, the cost per tonne of high titania product (76 per cent TiO2) would be nearly $70.

Jan 1, 1977

Wet mining of auriferous gravels at L & MÆs Waikaka operation in Southland creates spoil dumps derived from stripping of a clay rich overburden, tailings from past dredging and the processing of auriferous sands and gravels. Over recent times, spoil dumps have slumped on six occasions, threatening the viability of the wet mining operation. Close examination of slump morphology, coupled with the sequence of material placement and rate of dumping suggested a mechanism associated with undrained failure of a 2 m layer of silt and sand tails forming the base of dumps.Commencing with some information on the geotechnical properties of source overburden, back analysis of failure morphology and sequence and development of undrained loading conditions from first principals, the most likely failure mechanism and factors controlling failure were defined. Based on analysis results, a scheme to stabilise the lowwall dumps was developed and implemented, augmented by continuous monitoring of pore pressures in the basal wet tails, and laboratory testing for confirmation of computed material properties.Lowwall spoil stability has improved since implementation involving changes to the method of spoil loading, and modification of wet tails composition to improve permeability and drainage of the basal wet tails under load. The method and approach to prediction and verification of failure mechanism provide a sound basis for continued mining of deeper auriferous gravels.

Jan 1, 2002

By M. Slatter

The need for anti-corrosion coatings has existed for many years in the ground support industry, but the application requirements have made coating selection limited. Varying groundwater and chemical conditions continually challenge long term coating performance. Traditionally the industry coating preference has been hot-dip galvanizing due to its performance characteristics in highly corrosive environments and low cost nature. However, the galvanized coating has application limitations. This paper highlights some of these limitations and provides selection criteria for a new organic coating developed for one such difficult application, DSI?s Omega BoltPTM Pwhich is an expandable ground support. [ ]

Jan 1, 2009

By Marcel Vallée

Frequently, costs overruns and defaults in mining project performance result in serious problems and headaches for all project participants and impact on corporate objectives, profits and image and, occasionally, lead to project failure. As mining professional s, we should be very concerned that, in a recent World Bank paper (Weber-Fahr, 2001), geological and technical risks were considered the most important ones facing mining projects. Whenever we manage to reduce or minimize these risks, we are in better position to overcome the environment-, market-, finance- and community-related ones. The causes of this situation seem rather systemic, as a fairly long list of industry problems with new pro jects has been described in industry papers in pas t and recent years. A brief review of industry problems with mining projects will be given first, followed by a review of the basics of the current Quality Management and Continuous Improvement perspectives that have evolved from earlier quality control and quality assurance systems and policies. Particular particular attention will be given to the work of W. E. Deming. As the system approach is an essential part of such policies, it will be described succinctly. Given that poor communications and interactions among geologists, mineral processors and mining engineers/operators ca n seriously affect project efficiency and profitability, these interrelated processes with in the mining systems will be analyzed and modelled and the impacts of such situations will be described through a number of anonymous case histories and examples. A synthesis of Dr Deming's management system, includ ing his Four teen P oints and System of Profound Knowledge, will be prese nted .

May 1, 2002

By Michel Grenier, Robert Scott, Mahendra Gangal, Andrew Dasys

This research project which took place at Brunswick Mining and Smelting's Brunswick mine, was undertaken to assess the ability of new diesel engine technology to meet current and anticipated underground worker exposure limits to diesel exhaust contaminants. Concentrations of CO, CO2 NO, NO2 SO2 and respirable combustible dust (RCD) were measured in a remote mine area where a haulage truck was operating under simulated duty cycles. The 26 ton haulage truck was equipped with a 300 hp, electronically controlled engine. Fresh air was supplied to the area as per the MSHA certification document for this particular engine. Results showed that while the vehicle operated in a normal and realistic duty cycle, the concentrations of contaminants remained well below the ACGIH guidelines for the threshold limit values (TLV)for exposure. While operating at 630/0 of maximum horsepower (26 tons of ore in the dump), the time-weighted average exhaust gases concentrations (CO, CO2 NO, NO2 and SO2) never exceeded 150/0 of their respective TL Vs. ReD concentrations in this instance were measured at 0.59 mg/mJ or 39.30/0 of the exposure limit suggested by the Canadian ad hoc Diesel Committee. The Air Quality Index was 1.55 or 520/0 of the maximum suggested value for exposure.

Jan 1, 1994

By S H. Son, M K. Wang, H K. Jeong, B K. Cho, J I. Park

The utilisation of low-grade raw materials such as fine iron ore and semi-soft coking coal, and reduction of CO2 emissions are important issues in the ironmaking process. To solve these issues, a new process called PosPRA (POSCO prereduced agglomeration process) has been developing at POSCO. It focuses on the reduction of carbon composite iron ore briquette in travelling grate. In this study, the possibility of manufacturing the prereduced agglomerate (PRA) under oxidising atmosphere with travelling grate and the optimum manufacturing conditions of carbon composite iron ore briquette are investigated. The results have shown that controlling the temperature and oxygen potential in the range from 1100 to 1200°C and below 10 vol per cent respectively is very important to increase the reduction efficiency of briquette in travelling grate. High quality properties of the green briquette and PRA could be manufactured by using the briquette mixed with 20 wt per cent of coal under 0.1 mm in size under compacting pressure in the range from 3 to 7 t/cm. Adding 1 wt per cent water as a binder is proper under the condition of high compacting pressure. In a pot grate test, the compressive strength and metallisation degree of PRA are achieved over 150 kgf/p and about 55 per cent respectively, at bed temperature 1150°C and oxygen potential of 10 vol per cent when 20 wt per cent of coal is mixed in the briquette.CITATION:Wang, M K, Son, S H, Park, J I, Jeong, H K and Cho, B K, 2017. Development of prereduced agglomeration process using carbon composite iron ore briquette in travelling grate, in Proceedings Iron Ore 2017, pp 111–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau's Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939

By Robert A. Field

Static-Load Piledriving utilizes a hydraulic push to facilitate the installation of a pile. The pile is not rotated, impacted or vibrated. A smooth pushing force advances the pile incrementally into the ground. Static-Load devices must have a reaction mass to push against. The most simple form of a Static-Load device is a jack; more advanced equipment, such as the Still Worker, also utilizes this approach. This paper focuses on the use of the Still Worker on three challenging projects. In each case, the existing site conditions made it risky, or unattractive, to utilize conventional impact, vibratory, or drilled-shaft equipment.

Jan 1, 1997

By R. D. Dukimo, M. V. Sevian

The nature of fracture and factors that control the extent of fracture in the tumble-drum and drop-tower tests have been identified. The product-size distribution, on which the standard strength indices for these tests are based, and the breakage rate constants depend on a number of factors other than the strength of the lumps. The standard indices and rate constants are meaningful only in a comparative context and for events whose loading mechanism is similar. The results of experiments on three Australian ores, from Yandi, Koolan and Mount Whaleback, are used in combination with fracture mechanics theory to explain why different tumble-drum standards have been found to be fully consistent. A more meaningful measure of strength could be the parameters of the Weibull function, scatter and average strength

Jun 19, 1905

Underground equipment owners and users in order to compete and succeed in being viable business propositions must continually balance costs with productivity. By reducing their hourly ownership, operation and maintenance costs and increasing their hourly production, the cost per unit of material mined will be optimized.

Jan 1, 1990

By M. P. Ristenbatt

A new automated post-disaster signaling system, intended to use through-the-earth EM propagation, was demonstrated in the laboratory at an input SNR of -34 dB. The system presently available requires an input SNR of +6 dB, and uses a human-ear detector. The work here demonstrated coherent integration, for the automated system, in multiples of 17 s, up to 1088 s (18 minutes). A repeating pseudorandom (or pseudonoise) signal is used, which offers an ideal auto-correlation at the receiver matched-filter output. A novel decision-variable algorithm achieves the estimate of noise level by using those matched-filter output samples that occur between the signal auto-correlation peaks. This work included corraboration that the received signal power decreases as distance to the tenth power, for through-the-earth propagation. Thus, the above 40 dB reduction in required input SNR permits an automated system to have a range 2.5 times that of the present system. In addition, an automated system permits the possibility of operating receivers around-the-clock; this would reduce the initial-detection-time from a few hours (present system deployment time) to a few minutes (signal processing time).

Jan 1, 1981