Search Documents

By Donald R. McMahon

This paper presents a unique case history that documents the use of a braced secant pile wall to underpin a heavily loaded footing inside of a manufacturing plant. Construction of a pit for a new manufacturing process directly next to the footing necessitated the underpinning. The footing supports an overhead crane that needed to remain operational throughout construction of the pit and therefore, settlement of the footing could not be tolerated. The base of the footing was about 7.7 feet above the base of the 17-foot deep excavation. The footing bears on a silty clay deposit that grades from a stiff consistency beneath the footing to a soft/medium consistency near the base of the pit excavation. This paper describes the design and construction of the secant pile wall and bracing to control wall deformations, ground movements and settlement of the footing. The footing was monitored for settlement throughout construction of the pit and no measurable movement was observed.

Jan 1, 2006

By Dippenaar R, Evans T

Twin-roll continuous casting technology is rapidly approaching commercialisation. Fundamentally different than conventional continuous casting, heat transfer and hence solidification during twin-roll casting are governed by the interfacial melt/mould thermal resistance, as opposed to the resistance of the solidifying shell. Under these conditions the interface resistance is predominantly controlled by the melt/substrate wetting behaviour. The very early stages of melt/mould contact are characterised by highly transient heat transfer conditions. The overall melt cooling rates prior to the formation of the first solid are reported to be in the range of 1000 - 50000 K/s with melt undercoolings of up to 300 K. At the points of intimate melt/mould contact the thermal resistance is approaching zero, where cooling rates and undercooling much larger than those reported in the literature are probably occurring. Improved wetting will reduce the energy barrier for nucleation while at the same time increasing the cooling rate of the liquid. Since the overall nucleation rate is controlled both by the rate of cluster formation and the rate of atom transfer to the nucleus, a critical cooling rate will exist above which the nucleation rate is expected to be reduced. Under these conditions, it is possible that the first solid phase to form is a metastable glass which subsequently transforms into a crystalline phase. The implications on nucleation and early growth are also discussed.

Jan 1, 1999

By J. Björkvall, S. Ångström, L. Kallin

In this paper results from industrial trials of CaC2 injection during stainless steel production in an electric arc furnace at Sandvik Steel is presented. The main purpose of the investigation was to analyse the effect of the injection on slag foaming and final chromium oxide concentration in slag. The results show that both an increase in slag foaming and a decrease of the final chromium oxide could be obtained during the charges with CaC2injection. On the basis of the results, the economical requirements are also discussed. Both the technical and economical requirements could be achieved for steels alloyed with Mo. In order to secure the economical requirements for all steel grades of interest, the injection technology must be further developed. It would also be important to utilize the positive effect of the slag foaming on the electric energy consumption. The work has been performed as a part of MEFOS frame research programme with participants from Sandvik Steel, AKZO Nobel and Avesta Polarit. Keywords: stainless steel, EAF, slag foaming, injection, CaC2

Jan 1, 2004

By M. A. W. Bryson

Platinum group metals are extracted almost exclusively in South Africa from three very different zones in the Bushveld Igneous Complex, called the Plat, Merensky, and the UG-2 reefs. The Plat reef is currently being exploited only by Anglo American Platinum, whereas the Merensky reef is exploited by them, Impala Platinum, Northam, and Lonplats. The UG-2 reef, on the other hand, is also processed by these producers, but Kroondal and Barplats have operations that exclusively treat ore from this reef. At present the extraction of pgms from ores in South Africa follows the traditional route of upgrading to a concentrate in a minerals processing circuit, further upgrading to a matte in a smelter, and final upgrading and separation of the individual metals in a refinery. Thus all operations that extract pgms require a minerals processing circuit, the design and performance of which is a topic of much interest, as it is a poorly understood and not a very efficient process in relative terms, compared to the other processes. Recoveries across the minerals processing circuit of between 75 and 90% are the norm.

Jan 1, 2004

By Bruce I. Thomas

[THIS PAPER, tine of a series on placer ml n in iii Alaska, describes mining methods and gives unit costs at operations where hydraulic and mechanical excavation equipment is used with nonfloating washing plants. The mining methods described were developed during the last 30 years to copy with conditions peculiar to arctic and subarctic regions arid are now used by a large segment of the placer mining industry in Alaska. The operations described have been classified if m ii into three main categories: Those having sluices at a bedrock level, those having sluices above bedrock and those having mobile nonfloating washing plants (dryland dredges). Diesel-powered bulldozers and draglines convey or clevate gold-bearing gravel to the sluices, remove tailings, and strip waste gravel and other overburden. Diesel-powered centrifugal pumps supply water foe sluicing and hydraulic stripping. Detailed descriptions and unit cost arc presented for 14 operations to illustrate the numerous arrangements udder the first 2 categories.]

Jan 1, 1959

By D. Strachan

Installation of support in known poor ground intersections during reaming operations requires rapid access to stabilize the shaft wall and thus to prevent the loss of the shaft through scaling. This is especially relevant to shafts of long dimension where the duration from time of exposure to time of support installation is lengthy This paper deals with the innovative methodology employed at Harmony?s No. 8 Shaft 17/24 level sub ventilation shaft to rapidly support a shale intersection between 23 and 24 Level by employing a single deck stage suspended from the reamer head by means of Skyjack winches.

Jan 1, 2009

By B. Kenny

The aim of this paper is to provide an overview of existing forms of subcontracting in the South African mining industry. A descriptive framework is developed to understand different subcontracting arrangements. We argue that, in order to do so, it is important to distinguish between labour broking and gang subcontracting. Data resulting from a research project (including an analysis of historical sources, interviews with contractors and focus group interviews with mineworkers) is presented to highlight the implications of changing formations of subcontracting for the South African mining industry in the late 1990s. Apart from the subcontracting of ?traditional? functions, such as shaft sinking, access development, catering and hostel maintenance, contractors are now used in ?core? mining activities. In some instances, whole shafts are ?outsourced? to outside agencies. It is argued that certain of the subcontracting arrangements have serious implications for the ability of the mining industry to improve health and safety standards. Some of the practices can potentially result in conflict between different categories of workers, and, as a result, instability in the industry.

Jan 1, 1999

By J. S. Stachulak, G. H. Schnakenberg

The objective of the Diesel Emissions Evaluation Program (DEEP)-sponsored project at Inco's Stobie mine was to conduct a long term field evaluation of diesel particulate filter (DPF) systems available to the underground mining industry. Some of the major issues studied were criteria for selecting the filter media, means of DPF regeneration, efficiency of DPF systems and the occurrence of unwanted secondary emissions, and reliability and durability of DPF systems. Nine state-of-the-art diesel particulate matter (DPM) filtration systems have been retrofitted to heavy-duty and light-duty vehicles and have been subjected to extensive long-term in-mine evaluation. Periodic efficiency tests were conducted at various stages of the study (2001, 2002 and 2004) to establish in-use efficiencies and durability of the tested DPF systems. The results were used to assess the effects of the filter systems on the concentrations of particulate matter, nitric oxide, nitrogen dioxide and carbon monoxide in the vehicle exhaust. The variety of filtration systems and regeneration concepts used in this study offered the opportunity to investigate their advantages and disadvantages. This paper also offers a review of selected experiences with the installation and operation of the DPF systems on underground mining vehicles at the Inco Stobie Mine.

By D. Brün, T. W. Nattkemper, T. Kuhn, T. Schoening

Underwater exploration for marine resources using camera-equipped devices (OFOS, ROV, AUV) is receiving growing attention. This development is creating a continuously growing pile of digital underwater images leading to a serious bottleneck in the analysis. However, any harvesting strategy must be coupled to an efficient and effective assessment of the biodiversity in the area of interest and in nearby control areas. To integrate manual image and computational image interpretation on different levels (i.e. regarding geology and environmental sciences and taxonomy), sophisticated software support is required, which is not yet offered explicitly, neither by commercial software companies nor by academic or other publicly founded institutions. Here, we present the first version of a new digital asset management system that offers functionalities for easy data management, sharing, manual annotation and integration of computational modules for image enhancement/pre-processing and interpretation. The functionality is demonstrated with data from the CCZ provided by the BGR Hannover.

Sep 1, 2014

By R. K. Zipf

A method is presented for creating realistic numerical models for practical coal mine ground control. The method includes procedures to collect the necessary mechanical input parameters from a geologic core log, procedures to set up a model and procedures to interpret calculation results. The input parameters come from a detailed geologic core log and extensive point load tests of estimate rock layer strength. A suite of material property input parameters is proposed which allow the user to go from core log to numerical model inputs. Rock bolt anchorage properties are also linked to the material properties of each geologic layer in the model. Following this procedure leads to very realistic calculations of the rock failure process and rock support system behavior. These calculations in turn enable realistic comparison of the effectiveness of alternative rock support systems.

Remote sensing methods have been used to evaluate vegetative growth patterns for many applications, though relatively little work has focused on tracking mine reclamation progress. For coal mines in Central Appalachia, reclamation approaches that include production of biofuel feedstocks are increasingly attractive, as these may yield significant post-mining land values and contribute to carbon-neutral energy supplies. To optimize productivity, the influence of reclamation parameters must be well understood ? which necessitates tracking biomass production over long time periods. Satellite-based estimations may offer low-cost alternatives to conventional biomass appraisals, and also the potential to provide critical input for carbon accounting at varied spatial scales. In this paper, we use biomass production experimental plots on reclaimed mine sites established by the Powell River Project (PRP) for a comparative study between satellite measurements of Normalized Difference Vegetation Index and inventory estimates of biomass under a variety of conditions. The PRP is a unique public-private partnership in the coalfields of southwestern Virginia dedicated to enhancing beneficial use and environmental protection of mined lands.

Feb 27, 2013

By Ronald M. Lewis

Quadratic functions, Q(hkl), are given to six places in increments of 0.01° for 2? from 00 to 90° for FeKa and from 25° to 180° for FeKa1. The wavelengths used for Fe in the computation are those agreed upon by the Editorial Commission of the International Tables for X-ray Crystallography (1950): FeKa1 1.93597 A.; Feka2 1.93991 A. INTRODUCTION At the Federal Bureau of Mines laboratory, Norris, Tenn. X-ray diffraction crystallography using tubes with iron targets revealed a need for a handy reference for the quadratic functions of iron radiation. The tables presented here were prepared to satisfy that need. The quadratic form Q(hkl) may be expressed in terms of the Bragg diffraction angle 2? and of the wavelength ? as

Jan 1, 1961

By T. Hudaverdi

Control of the particle size distribution of a muckpile after blasting is always an important subject for mining industry. Blasting has a significant impact on downstream processes such as loading, crushing and grinding. Improvement of blasting results provides increase in loader and excavator productivity due to increased diggability capacity, and increased bucket and truck fill factors. Suitable and uniform particle size distribution results increase in crusher and mill throughput and decrease in energy consumption in size reduction process. Digital image analysis technique has been used for many years in mining industry in order to determine blast fragmentation. The images of muckpile surface can be used to determine the mean fragment size (x50). The source of digital images can also be haul truck, leach pile, waste dump, stockpile, and conveyor belt. The screening that is conventional method to measure blast fragmentation is time consuming and expensive. Digital image analysis is a cost effective and faster method (1).

Jan 1, 2012

By O. Naiker

Xstrata has modified and improved on the solid state reduction of chromite (SRC) process that was pioneered by Showa Denko in Japan and previously used at Xstrata?s Lydenburg plant. The history of pre-reduction is a long one, with the SRC process being the first and only commercially successful one prior to Premus. Krupp developed the chromite direct reduction and the rotary hearth for the pre-reduction of chromite. However, these processes have not been successfully commercialised. The are a number of significant differences between Xstrata?s patented Premus and the original Consolidated Metallurgical Industries (CMI) process. These include, the use of lower cost anthracite fines as the reductant source together with the use of unactivated bentonite as the binding agent. In addition the use of oxygen as an energy source is used in Premus but not in the original CMI process. There was a fundamental change in the operational philosophy of the process in that while the original CMI process aimed to maximize metallization of the pellets, the Premus process seeks to maximize the energy output from the kiln while still achieving the required efficiencies and hence increasing furnace output. Premus is designed to reduce electrical energy consumption, provide high recoveries of metallic oxides, and utilizes low cost reductant and energy sources such as anthracite and oxygen respectively. Due to the fact that Premus is one of the most technologically advanced and competitive processes used today in the production of ferrochrome it was the process selected for Xstrata?s new ferrochrome facility, Project Lion, that is due to be commissioned in the third quarter of 2006 in the Steelpoort Valley in Mpumulanga, South Africa.

Jan 1, 2007

By P. Mousset-Jones, G. Danko

Variations of the temperature and steam/moisture content of the air with distance and time are modelled for a single airway. The input for the simulation is an air temperature that varies with time, together with the moisture/steam content that results, for example, from a fire with a given distribution of heat and of fume concentrations at the beginning of the airway. The transport of heat and moisture to the surface of the wallrock is assumed to be simultaneous. Such multiphase convection may result in evaporation from the moist wall close to the fire and recondensation downstream. The modelling of this non-linear effect is a unique feature of the new simulation. A new analytical solution is used to calculate the conduction of transient heat within the rock mantle, which, in the event of a fire, is typically a short-term process. This allows for an arbitrary variation of surface temperature with time - unlike that permitted by the age function solution, which is limited to stepped temperature changes. An iterative numerical scheme that has recently been developed to simulate mine climate is used to calculate the coupled transient heat conduction and multiphase surface heat transport in successive length increments along the airway. To demonstrate the simulation procedure a numerical example is presented in which a fire with a given distribution of heat and fume concentrations with time is located at the beginning of an airway

May 1, 1991

By Harry G. Poulos

Ground movements can arise from a large number of sources and can have a significant effect on nearby piles and deep foundations. The loading of the piles by ground movements is a different mechanism to that arising from direct applied loading to the pile head, and consequently it is not generally possible to adequately analyze the effects of ground movements simply by applying some type of equivalent loading to the pile head. The main effects of ground movements are the development of additional movements, axial forces and bending moments in the piles, and thus the key design aspects are related to movements and to the structural integrity of the pile. However, the ultimate geotechnical load carrying capacity is generally not affected by the ground movements themselves. This paper will describe an approach to the analysis of ground movement effects on piles, considering axial and lateral movements separately. Some of the main features of pile response will be discussed for three specific problems involving ground movements: piles near and within embankments, piles near an excavation for a pile cap, and piles subjected to seismic ground motions.

Jan 1, 2006

By B. Xu

Keywords: Magnetic damping, g-jitter, Hot-film anemometry Results from an experimental study on natural convection induced by temperature gradient in molten gallium contained inside a rectangular container. The damping effect of the convective flow from an externally applied static magnetic field is investigated. Induced velocity and temperature fields are mapped using a standard constant temperature hot-film anemometry and a thermocouple with and without the applied magnetic field, respectively. Detailed experimental setup and procedure are depicted in the present paper. Obtained velocity and temperature profiles are examined against previous numerical simulations and reasonably good agreement has been achieved. Obvious damping effect can be observed in both the temperature and the velocity profiles when the external magnetic field presents.

Jan 1, 2005

By G. Caron, M. Boisclair

In 2005, CANMET-MMSL used its pool of expertise in ground control, open pit and underground mine engineering, mineral processing, information technology and applied mineralogy to launch a mine-to-mill research project. The objective of the project was to optimize the distribution of rock breakage energy among blasting, crushing and grinding activities, thereby maximizing the efficiency of energy utilization within comminution processes. Tests were designed to demonstrate that this approach could reduce the energy consumption, thus contributing to the reduction of Green House Gas (GHG) production in the Canadian mining industry. The project was accomplished in collaboration with DynoConsult and Dyno Nobel Canada Inc., a world leader in commercial explosives. Data analysis from 12 blasts (six with electronic and six with pyrotechnic detonators) in three different geological formations of a quarry (soft, medium and hard rock) shows that electronic blasting technology increases rock fragmentation by 15% (in hard rock) to 20% (in soft rock). A more uniform rock fragment size distribution is also obtained. The impact of the improved quality blast product on downstream processes of the quarry is a productivity increase of 5% in rock excavation and transportation, an energy reduction of 10% at the primary crusher and an increase of 15% of the primary crusher throughput. A soft-sensor prototype, based on primary crusher data (i.e. energy consumption, throughput, feed and product size distribution) and a simplified computerized process model, was developed for on-line measurement of the rock operating work index. Additionally, 385 rock samples and specimens were collected and prepared to determine the tensile and compressive strength of the rock material, to evaluate the aggregate crushing work index, and to examine the development of micro- and macro-fractures by means of binocular and SEM microscopy. Blast-induced rock damage was evaluated at the end of the laboratory testing program. Even though a reduction of rock hardness of around 30% was observed after blasting, the impact of the blasting method (i.e. use of electronic or pyrotechnic detonators) on the induced rock damage could not be observed. It is either absent or not perceptible with the accuracy of the measuring techniques and the number of samples analyzed.

Jan 1, 2007

By H. B. Hill

The West Red River oil field, in Tillman County, Okla. (fig. 1), is approximately 8 miles northwest of the town of Burkburnett, Wichita County, Tex. The wells are in the river bed between the medial line and the south bank of the Red Diver. In the following discussion of the geology, development, and exploita-tion of the field, the authors have, by means of structure maps, crews sections through various parts of the reservoir and tabulated development data and production statistics, recorded salient information on a field whose development was unique and in some respects unusual for fields discovered and initially developed more than a quarter of a century ago. The total oil production from Government-operated leases; considered in the report was 6,900,440 barrels to January 1, 1947, from 3 proved acres developed by H1 oil-producing wells, 10 gas-injection wells, and 5 nonproductive wells. A calculated past recovery of 60P, barrels of oil per acre-foot and an estimated ultimate recovery of 6.S0 barrels of oil per acre-foot under present gas-injection methods begun in 1929 in shown.

Jan 1, 1949

By Antonio Pineda, Roger K. McLimans, Felicity E. Lloyd

lmenite is a primary ore feed to the DuPont chloride process for the manufacture of titanium diox-ide pigment. We seek to determine ilmenite geochemistry as a function of original source and as-certain which ilmenites have chemistry most amenable to upgrading via iron-leaching (leucoxenization) and that have favorable, with respect to pigment manufacture, trace element content. Ilmenite geochemistry is a function of its primary origin and of subsequent alteration. Heavy mineral sand deposits may contain ilmenite from one or several dominant source rock(s). In addition, ilmenite may alter in the weathering environment, changing the major element compo-sition (iron-leaching) and certain of the minor element content. A primary objective is to classify ilmenites in relation to origin in order to fingerprint source rocks in provenance determination. The changes in trace element chemistry during alteration are also investigated. A “decision tree” is developed to classify ilmenite types and source rock origins. Ultimately, with those methods and by amassing a database of ilmenite types from worldwide locations, it should prove possible to determine ilmenites (and their sources) more susceptible to iron leaching in the weathering en-vironment. Such ilmenites, enhanced in their titanium content, are the preferred ore targets. The method used is electron microprobe analyses at elevated conditions of voltage, cur-rent, and counting time to enable higher precision. In-situ ilmenites from igneous, metamorphic, and altered rocks (saprolites) are analyzed. Initial foci for sedimentary ilmenites are restricted provenance (approaching monogenetic, examples from Spain, Portugal) and polygenetic prove-nance (Denmark). Altered ilmenites, including the DuPont Florida ore, are used to characterize the chemistry of leucoxenization. Trace element concentration, detectability, and cost considera-tion, led to focus on Mn, Mg, V, Cr, and Nb to develop a classification scheme validated by dis-criminant analysis and “classification-regression trees”. Results show a high degree of success for restricted provenance study and an acceptable one for polygenetic provenance.

Jan 1, 2005