Search Documents

By Jacob Chacko

The east span of the San Francisco-Oakland Bay Bridge (SFOBB), which is one of the most heavily traveled bridges in the world, will be replaced due to seismic safety concerns. The majority of the new bridge will be founded on large-diameter (1.8 to 2.5 meters), approximately 60- to 100-meter-long pile foundations The large-diameter steel pipe piles and soil conditions are similar to those used/encountered in many offshore structures. Thus, the design methods used are based on site-specific modifications to the procedures recommended by the American Petroleum Institute rather than the conventional procedures that have been formulated and used for the design of much smaller piles. Pile foundations will experience their maximum loads during the design earthquake. For the Safety Evaluation Earthquake, tension loads of up to approximately 80 to 90 meganewtons (MN) and compression loads of up to approximately 120 to 140 MN were calculated. Due to the economic importance of the SFOBB and the consequences of catastrophic failure in both economic and human terms, the design and analysis of the pile foundations supporting the bridge consider a number of aspects of pile-soil behavior that are normally ignored. Those aspects include: 1) the effects of consolidation and setup, 2) the behavior under dynamic loading, 3) the losses of resistance under cyclic loading, and 4) the load-settlement behavior of the piles under severe cyclic loading conditions. Since the treatment of complex aspects of pile foundation behavior is not codified in any guiding documents, several project-specific methods were developed for design and analysis of the foundation piles.

Jan 1, 2002

By Zach Ellis, Dusty Fisher

The Office of Surface Mining, Reclamation, and Enforcement (OSM) cited a large surface coal mine for a series of flyrock incidents that occurred when blasting close to the mining lease perimeter. The OSM placed the company on a pattern of violation status. It was determined through analysis of blasting practices that flyrock could be controlled at the mine by drilling a smaller diameter hole and stemming with crushed rock when blasting within 1,000’ (304 m) of the lease line. The procedure to install and remove the small diameter drill steel was cumbersome and dangerous because it was a manual transition. The drill carousel could only hold one diameter at the time the project was initiated. The process was very time consuming, involving a mechanic to transport the steel to the drill and spend up to 1.5 hours of downtime switching the steel. In addition, the hydraulically operated break-out wrench and break-out fork on the SKS Infinity Redrill® is only designed to work with one diameter, so these tools could not be used to disconnect subs and steels on the string. At the time, the mine’s breakdown was between 30-40% small diameter (6 ¾” (171 mm)) versus large diameter drilling (10 5/8” (270 mm)). The drill and blast group was challenged with the task to implement a 6s (Six Sigma) project that would reduce the amount of time spent on steel change-outs on the rotary drills while improving the safety of the task. A solution was proposed to carry the small diameter drill pipe, lower small diameter sub, and small diameter bit on board the drill at all times. The goal of the project was to carry the steel in the carousel after modification so that the driller could change the diameter himself on board the drill in less than 45 minutes without any assistance from a mechanic. The drill had to be modified so that the hydraulic operated break out wrench and deck fork could be utilized on both diameters. The drill accessory supplier and the mine worked together to design and implement design changes and new equipment onto two rotary drills, and new standard operating procedures (SOPs) were created for the new process. The project has been in the sustaining phase for approximately three months now and all steel diameter changes are completed by the operator under the allowable time limit.

Jan 1, 2015

By J. H. Zietsman, M. W. Erwee, P. J. A. Bezuidenhout, Q. G. Reynolds

"Pyrometallurgical furnaces are tapped through tap-holes that are opened with drills and oxygen lances. The lance is often used on its own or as the last step of opening the tap-hole. Interaction of oxygen with molten material inside the tap-hole can occur, and is a phenomenon that is not well understood. As part of a study that focuses on the effect of lancing on flow inside and around the furnace tap-hole, a cold-model validation was done. The validation study focuses on validating the MULTIPHASEINTERFOAM multiphase flow solver in OpenFOAM® for the problem involved. The sensitivity of the model to different materials properties (viscosity and density in particular) is presented with both cold models and the results from flow simulations in OpenFOAM®. IntroductionMany pyrometallurgical operations are carried out in furnaces where molten material accumulates continuously. Once enough material has accumulated and is ready to be removed from the furnace, material is tapped through one or more tap-holes in the furnace. Tap-holes differ significantly in both geometry and materials of construction, depending on the process involved – examples of different types of tap-hole configurations can be found in, for example, Nelson and Hundermark (2014). Tapholes all share one common feature: they are high, wear areas of the furnace. Molten material at high temperature flows through these areas, after which the tap-hole is sealed, usually using tap-hole clay. The purpose of the tap-hole clay is to harden inside the tap-hole and seal it until the next tap.Once ready to tap, a pneumatic drill and/or oxygen lance is used to open the tap-hole. The extent of lancing a furnace tap-hole depends strongly on the type of furnace. In, for example, many blast furnace operations lancing is limited as much as possible, and done only if drilling was not effective. In other operations, such as on small-scale pilot furnaces with short tap-holes, only lancing is used to open the tap-hole."

Jun 1, 2019

By Anastasia M. Suchowerska

The design of effective ground support requires a sound understanding of the pre-mining state of stress in the stratum to be mined. Irregularities in the stress field encountered during multiseam mining are governed primarily by the previous mining in the surrounding strata. The aim of this study is to quantify the effects of rock mass transverse isotropy on the vertical stress redistribution in the rock strata beneath supercritical longwall panels. Wilson?s equations for determining the stress distribution induced in and beyond a single longwall panel after it has been mined have been adopted, and a plane strain finite element analysis of an elastic medium, together with the stress changes predicted by Wilson, was used to calculate the final pre-mining stresses in the underlying strata. Values of the independent shear modulus (G¢) of the rock strata, ranging from 0.1 to 1 times the isotropic shear modulus (Giso) in the plane of the strata, and a Poisson?s ratio (?) of 0.25 have been investigated. The key finding of this study is that the predicted magnitude of vertical stress in the transversely isotropic strata beneath a mined supercritical longwall panel is larger and changes more quickly with horizontal distance than is the case for an isotropic rock mass. This finding is of significance for the design of ground support measures in multi-seam mining operations.

Jan 1, 2012

By W. J. van Niekerk

Ballast Nedam is in Surinam constructing two bridges that will improve communications in the coastal region. The bridges will cross the Coppenam and Surinam rivers and will be founded on open-ended steel piles over 60 meters in length. The majority of piles are inclined and support prefabricated concrete girders forming the roadway. In most locations the stratum is consolidated cohesive layers extending to a depth in excess of 60 meters. For this reason, before pile driving operations commenced, it was decided that a number of test loads would be carried out determine the capacity of the piles. Loading tests were carried out on specially installed piles as well as on piles that would be used as working piles to support the structure. Working piles were dynamically tested using Pile Driving Analysis (PDA) equipment. This decision was based on the inclination of the piles, the cohesive nature of the soil and the increase of strength after the piles are driven. A good insight has been obtained into the real strength of the soil by comparing dynamic and static loading tests on vertical test piles. This made it possible to determine the required length of pile.

Jan 1, 2000

By Maurício Covcevich Bagatini, Maycon Athayde

Nowadays, the HPGR (high-pressure grinding rolls) is an intermediate step between filtering and balling in the most modern iron ore pelletizing operation. The operation debottlenecks filtering process and reduces pressure over the typical milling process to control particle size to the balling. The present study evaluated aspects of microwave application to the iron ore concentrate fed to HPGR in a bench scale unit. Iron ore concentrate was irradiated varying the microwave exposure time and grinding efficiency was evaluated. The moisture influence in the HPGR efficiency was also assessed. The pellet feed blaine surface area (BSA) improved by 300 cm2/g and % < 325# fraction by 3%. Scanning electron microscope (SEM) images show the formation of micro-cracks onto the particle surface induced by microwave; the effect observed helped improve the milling process performance, in addition to the moisture reduction observed due to the temperature increase.

By Professor of Civil and Environmental Engineering Northwestern University, Mike Wladron, Gordon Revey

A unique judicial opportunity allowed measurement of the response of three cracks in residential structure to blasting for underground aggregate mining. Instrumented cracks were located in the interior basement CMU mortar and upstairs dry wall as well as exterior brickwork. The dynamic environment was unusual. Even though the blasting occurred some 490 m (1600 ft) away, excitation frequencies were unusually high and there were no apparent surface waves. In addition there was no air overpressure wave to produce secondary crack response. As is typical, long term environmental effects produced greater crack response than did the blast induced ground motions.

Jan 1, 2007

By D Nicoli, P Feltoe

The operation of grinding circuits are vital to the success of most mineral processing operations in the provision of effective size reduction whilst maximising throughput. However these same circuits, and especially semi-autogenous grinding (SAG) mills, are highly interactive with product re-circulations and long time delays. This makes the optimal control of these difficult by conventional controllers, such as PID, which generally places a heavy reliance upon operations for control. In order to account for the peculiarities (such as ore type changes) and the abnormal situations that continually beset these circuits, it is necessary to adapt linear control techniques to cater for these situations. The Honeywell Hi-Spec Solutions SmartGrindTM controller is a marriage of multivariable predictive control (MPC) with techniques that provide adaptation of the control to optimise the circuit under all conditions. Optimal control is achieved by incorporating pattern recognition techniques to detect and act on discrete events (eg ore type changes) and adaptation of the MPC to account for known process and equipment non-linearities. AlcoaÆs Wagerup Refinery is the first site worldwide to have this technology applied to the SAG milling circuits and this has resulted in throughput increases in excess of two per cent and significant improvements in circuit operations. This paper describes the implementation of the control to the refineryÆs Mill 3 bauxite grinding circuit and the capacity/operational improvements achieved thereof.

Jan 1, 2000

By Michel Ruel

"This paper describes how to make advanced control choices when difficult processes need improvement. The decision-making process involves choosing between a rules-based approach and a model-based approach as well as weighing benefits and drawbacks, complexity and simplicity, investment and results. This paper will present briefly each solution: basic control, advanced regulatory control, model predictive control, and expert systems such as fuzzy logic controllers and neural networks. The article then proposes a decision tree for selecting the most appropriate approach. A table will compare usage, development, commissioning, maintenance and lifecycle costs for each approach. Finally, conclusions and suggestions will summarize the methodology.INTRODUCTION Advanced process control (APC) is a popular topic. How can one decide whether advanced control should be added to an existing system? Advanced control is used to improve performance, stabilize production, handle constraints, protect equipment and manage grade changes. Most plants use feedback controllers, usually PID (proportional, integral, derivative) controllers. It is common to develop special control schemes to handle more complex processes. In classic PID process control, a controller brings a single value close to a set point using a single manipulated variable. On the other hand, APC brings several values close to optimal targets simultaneously using several manipulated variables. APC's four main strategies are advanced regulatory control, model predictive control (MPC), fuzzy logic and neural networks. Simple solutions are always preferred. Complexity will be increased if performances (production, quality, etc.) are below par. Profitability analyses should be conducted to validate project viability. Needs—not trends—should dictate choices! Before increasing complexity, it is important to define needs, goals, technical support, budget, etc. All these approaches entail strengths and weaknesses. Building a project based on technology rather than needs spells trouble."

Jan 1, 2014

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of raining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENT The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By J Cahill, D Holden, R Stuart, G Cryan, W Power, W Stratford, S Garwin

The combination of Stage 1 Geoinformatics legacy data intervention processes with the Stage 2 ultra-detailed airborne geophysical prospecting demonstrates a new approach to converting data to information to knowledge, and converting that knowledge into exploration results. &nbsp; The Coromandel region of the North Island of New Zealand has long been know to host gold deposits of economic viability (Hauraki Gold Fields). To the SE of this area lies the Taupo Volcanic Region (TVR) where the geology and structural setting mirror the Hauraki Gold Fields, however mineral exploration in the past has been hindered by the blanketing volcanic ash deposits. Glass Earth Limited recognised that this whole potential epithermal gold province could be effectively explored utilising rapid, risk orientated processing to review legacy geoscience data: The Geoinformatics Data Intervention Process; which in turn directed ultra detailed airborne geophysical surveys over the TVR. Results have outlined 21 new drillable potential epithermal gold targets; and a plethora of other targets with high prospectivity.

Jan 1, 2005

By Q. G. Reynolds

The presence of dust and fume suspended in the freeboard region is a common feature of the operation of direct current (DC) plasma smelting furnaces. This occurs primarily as a result of the use of fine feed materials together with the open-arc, open-bath operation of such smelters, and is exacerbated by the high velocities and turbulent mixing of the gas in the vicinity of the arc jet. Dust and fume losses into the furnace off-gas system can be significant in some cases and may have economic, operational, and environmental impacts on the process. A computational modelling study is presented in which the concentration of dust material was considered as a continuous field subject to a governing partial differential equation. Settling behaviour was calculated as a function of particle size, local gas/plasma temperature, and other physical properties. Development of the coupling between the concentration field and a magnetohydrodynamic description of the arc is shown, and the resulting models were used to compute various aspects of the behaviour of the concentration field in the arc region for a variety of furnace conditions. Time-averaged as well as transient models of the arc were used to generate the results presented. Qualitative case studies produced several practical suggestions for furnace operation, including increased dust capture by the bath when feed ports are located closer to the electrode, and the possible effects of feed segregation in the furnace freeboard based on dust particle size and density.

Jan 1, 2015

By Kenneth R. Maser

This report describes the development of a system which modifies an existing fly ash-foam remote mine sealing technique to make it capable of impounding water in a fire zone. The modification involves blending equal quantities of fly ash and bentonite to form the bulk of the seal, and blending a thin layer of fly ash and Huron Regulated Set Portland Cement (RSPC) as a coating. The modification replaces the pure fly ash approach, but continues to use a froth foam topping to complete the seal. The modified material system is implemented with minimal complexity by adapting a "Y" connector to the existing delivery system. Each bulk hauler (fly ash and bentonite, or RSPC) will pump into one leg of the &apos;Y&apos;; and the blending will be controlled by two pinch valves. The development effort has involved an evaluation of potential material systems by using small sample, quarter scale, and full head tests. The small sample tests measured the basic properties of a large number of selected material combinations. Property measurements included capillarity, permeability, shrinkage, and shear strength. As a result of these tests, particular combinations of fly ash-bentonite and fly ash-cement were selected for scale model testing in a 1 /4 scale test facility. These tests simulated, in a scaled manner, the water rise and total head which would be experienced by a seal. The tests indicated that shrinkage in the fly ash-cement combination would always result in leakage; whereas, fly ash-bentonite mixes were impervious to water.

Jan 1, 1974

By S. Sarac

In this study, graphical and mathematical methods used to determine operating points in single or multiple fan ventilation systems are summarized. The problem is mathematically formulized for parallel connected fans in which analytical solutions are not possible. For n number of parallel connected fans, a non-linear equation system that consists of n number of non-linear equation sis derived. The Newton-Raphson method, which is a numerical analysis method, is adapted to solve this non-linear equation system and the solution steps are given as an algorithm. A computer program based on this algorithm is written and its applicability is proved.

Jan 1, 2000

Researchers from the National Institute for Occupational Safety and Health (NIOSH) are developing a coal pillar rib rating (CPRR) technique to measure the integrity of coal ribs. The CPRR characterizes the rib composition and evaluates its impact on the inherent stability of the coal ribs. The CPRR utilizes four parameters: rib homogeneity, bedding condition, face cleat orientation with respect to entry direction, and rib height. All these parameters are measurable in the field. A rib data collecting procedure and a simple sheet to calculate the CPRR were developed.

Jan 7, 2020

By John P. Capp

After World War II the Bureau of Mines studied methods of producing synthesis gas including a plan to gasify coal in place. Consequently, under a cooperative agreement with the Alabama Power Co., Bureau engineers directed a series of experiments that were carried out on the property of the Alabama Power Co. at Gorgas, Ala. The purpose of underground gasification of coal, regardless of method used, is to obtain the energy contained in the fuel for use on the surface, without mining in the usual sense of the term. Underground gasification can be described as (1) a process where coal, in place, is consumed by partial combustion with air, oxygen, steam, or any combination of these to produce a low calorific value gas (80 to 300 Btu per cu ft) or (2) a complete combustion process in which air is used to produce a gas containing carbon dioxide, nitrogen, and considerable thermal energy.

Jan 1, 1963

By John P. Capp

After World War II the Bureau of Mines studied methods of producing synthesis gas including a plan to gasify coal in place. Consequently, under a cooperative agreement with the Alabama Power Co., Bureau engineers directed a series of experiments that were carried out on the property of the Alabama Power Co. at Gorgas, Ala. The purpose of underground gasification of coal, regardless of method used, is to obtain the energy contained in the fuel for use on the surface, without mining in the usual sense of the term. Underground gasification can be described as (1) a process where coal, in place, is consumed by partial combustion with air, oxygen, steam, or any combination of these to produce a low calorific value gas (80 to 300 Btu per cu ft) or (2) a complete combustion process in which air is used to produce a gas containing carbon dioxide, nitrogen, and considerable thermal energy.

Jan 1, 1963

By J. F. Havard

The enterprises based upon the industrial minerals are diversified in geologic habit, mining systems, processing techniques and marketing methods. Nevertheless, in 1972 these enterprises faced many of the same frustrations and hopes and knotty problems and crucial decisions. Volume and profits were generally improved but were uneven in extent and effect. The U.S. cement industry, for example, was unable to meet demand in major markets. It was constricted by a frozen low-level price structure, faced expensive pollution control measures and watched heavy imports penetrating its markets from several European nations, Mexico and Canada.

Jan 1, 1973

By S Telford, J Weir

Heathgate Resources Pty Ltd (Heathgate) operates the Beverley Uranium Mine in South Australia, located on the plains between the northern Flinders Ranges and Lake Frome some 600 km north of the state capital Adelaide. The uranium orebody exists in permeable sands within the confined, highly saline Beverley aquifer, approximately 125 m below the ground surface and the uranium is mined using in situ recovery (ISR) technology. The Beverley mine is a highly technologically advanced ISR mine and is operated in accordance with stringent safety and environmental standards. The mine is currently licensed to export 1500 t of uranium oxide (U3O8) per annum. This paper outlines the fundamental differences between ISR operations and the more traditional uranium production methods, such as agitation leaching and heap leaching, where the ore is removed from the deposit, stockpiled, crushed, milled and leached on the surface. Solids tailings from either the mill or the heap are finally deposited in a tailing storage facility. ISR mining differs from conventional mining because the ore remains in place underground (in situ) and the groundwater contained in the ore-bearing aquifer is utilised as the mining fluid. This is achieved by drilling into the deposit and installing wells for extracting and re-injecting the groundwater which is fortified with chemicals. The fortified groundwater (ie mining fluid) flows through the permeable sands containing the orebody, dissolving the uranium. The pregnant mining fluid is then collected and transferred to the recovery plant where the uranium is captured (on ion exchange (IX) resin in the case of Beverley). The barren mining fluid is then re-fortified and recycled to the wellfields. Once mining is completed in a wellfield, the surface infrastructure is relocated to a new wellfield, and the mined-out wellfield is rehabilitated to its original surface condition. A comparison of &apos;standard&apos; hydrometallurgical plants, heap leach and ISR shows a number of key differences, such as the rate of leaching, the level of control available to the operators, and the type of contact/reaction that occurs. While limited in its applications, ISR mining has proven successful at Beverley and provides another mining and processing method for the production of uranium.

Jan 1, 2008

By Robert B. Bittner

"AbstractLarge diameter tubular piles offer significant advantages in terms of design performance and economy for major marine structures. This is particularly true for foundations of major overwater bridges in regions of high seismicity such as the west coast of North America. The use of large diameter piles in the range of 2 to 3 m diameter means that fewer piles are required, and the size and mass of the pile caps can be significantly reduced, thereby greatly reducing lateral load demand during seismic events. Another advantage of using larger diameter piles is increased pile stiffness that allows the pile caps to be located at or near the waterline rather than being positioned at or below the mud line. This elevating of the pile cap offers significant cost savings by eliminating the need for deep cofferdams. However, relocation of the pile cap creates new problems and opportunities in regard to the means and methods used to construct the pile cap. With the pile cap at depth, conventional steel sheet pile cofferdams with thick tremie seals are typically used to isolated the cap location and allow dewatering for construction of the cap. However with pile caps positioned up off the bottom, conventional bottom founded cofferdams are no longer cost efficient. Float-in or lift-in cofferdams have been developed to address the need for a more cost efficient method for cap construction. This paper describes the key features of the concept and provides three case history examples of its successful implementation.Pier Construction Using Conventional Sheet-Pile CofferdamsCofferdams are temporary structures used in the construction of bridge piers and other marine structures. Their primary purpose is to hold out water and unstable soil from the construction area, and thereby, allow in-the-dry construction of the permanent structure below the water line and quite often below the mud line. Typically, cofferdams consist of long interlocking steel sheet piles driven through water into the bottom of the waterway. The sheet piles form temporary exterior walls which are typically braced internally with wales and struts. The bottom of the cofferdam is typically sealed with tremie concrete or an impervious clay layer if one exists. The depth at which this type of cofferdam can be used is typically limited by the length of steel sheet pile that can be transported and handled by conventional marine equipment."

Jan 1, 2014