Search Documents

By Ruilin Yang

The following simple equations are frequently used within the blast vibration community;PPA f PPV v = 2p · , PPV f PPD d = 2p · ,a f PPV PPA 2p = , and v f PPD PPV 2p = where, PPA is the peak particle acceleration, PPV is the peak particle velocity, PPD is the peak particle displacement, and fa , fv , and fd are the frequency of the particle acceleration, particle velocity, and particle displacement vibration waveforms, respectively. Conceptually, the frequency should be selected to be the frequency of a simple sinusoidal wave that is used to approximate the blast vibration. In the literature, f is sometimes chosen as the dominant frequency (fdm) estimated from the Fast Fourier Transform (FFT) of the blast vibration wave, on other occasions, f is chosen to be the principal frequency (fpr) from the vibration cycle with the peak vibration amplitude.

Jan 1, 2012

By J. L. Holman

The Bureau of Mines is conducting research to improve technology for the recovery of strategic and critical metals, such as cobalt, nickel, and chromium, that are lost in bulk and particulate superalloy-type scrap because it has not been possible to process mixed contaminated scrap efficiently. The research approach involves melting and casting mixed superalloy scrap into soluble anodes for electrodeposition of Ni-Co alloys by controlled-potential electrolysis. The initial experimental results described in this report are from electrolytic tests us-ing alloy anodes cast from elemental nickel, cobalt, and chromium, the main constituent metals of superalloys. Baseline data and operating parameters are necessary for Ni-Co and Ni-Co-Cr alloys before detailed experiments can be conducted on the more complex superalloy scrap. This basic research assessed the effects of cathode potential, S04:CI electrolyte ratio, electrolyte pH, stirring rate, deposition time, cathode current density, and chromium concentration on cathode current efficiency, alloy deposit composition, and deposition potential at a cell temperature of 55° C.

Jan 1, 1985

This paper describes the new legislative regime that will apply to the regulation of the minerals industry in New Zealand. The reform of New ZealandÆs minerals legislation was initiated in January 1988 when the Minister for the Environment, Rt Hon Geoffrey Palmer, announced the Governments intention to review all the major laws governing New ZealandÆs resources. The Resource Management Bill is scheduled for introduction to the House in December 1989 and its date of enactment is scheduled for June 1990. With some matters still to be determined (at the time of writing), this paper cannot be a definitive review and description of the new legislation, it is instead an attempt to outline the major features of the Bill, to date, that are seen as important to the mining industry.

Jan 1, 1990

By Matthew A. Perras

With growing populations, infrastructure projects are utilizing underground space to expand transportation networks, water supply and sewer disposal systems and hydropower facilities. These new projects require large diameter tunnels to meet the growing demands. As the tunnel diameter increases, not all rock mass properties are scalable and precedent experience becomes less reliable. One such non-scaleable property is lamination thickness. Numerical modelling was conducted to determine the influence of lamination thicknesses on a 16 m diameter tunnel. Five different areas of excavation response were found to exist for laminations ranging between 0.16 to 16 metres in thickness. For this tunnel diameter, critical lamination thicknesses of 6 metre and 1 metre were found to exist. Above 6 metres the excavation response was similar to isotropic models. Below 6 metres the stresses and yield are channeled by the lamination boundaries, increasing plastic deformation. Below 1m multiple lamination units become unstable and the displacements increase significantly and the shape and extent of the yield zone size changes dramatically. The yield zone is controlled by bed deflections and bed parallel shear. As the lamination thickness decreases tensile failure first begins in the haunch area and progressively extends above the crown until a self-limiting plastic yield zone shape is reach at lamination thicknesses below 0.4 metres. Conclusions drawn from observations at the Niagara Tunnel Project are those of the authors.

May 1, 2009

By Ray H. S, Galgali R. K

It is well accepted that the blast furnace will continue as the main route for iron-making for many more years. However, its limitations have motivated researchers to look for alternative routes, particularly, those where non-coking coal is used for liquid iron production. Smelting reduction (SR), where coal and oxygen are used to produce liquid iron and power is now receiving serious attention. Several smelting reduction reactors are now operating in pilot plant scale and one or two have reached commercial status.

Jan 1, 1999

By M. Tarvainen

"Lately, the development work in closed circuit grinding has mainly been focused on mills and on different types of instrumentation, mathematical models and automation in spite of the fact that the poor efficiency of the classifier is well known. It has also been proven by several investigations that by improving the sharpness of classifier separation, remarkable technical and economical advantages can be achieved. Some attempts to improve the performance of the most common classifier, hydrocyclone, have been made, among them injection of wash water above the spigot cyclone and retreatment of either or both of the products of the primary classifier. No method has been successful enough to achieve general adoption in the industry. The purpose of this paper is to introduce some industrial results achieved by two-stage classification where the coarse product of the turbulent-flow classifier, hydrocyclone, is cleaned in a laminar-flow cone classifier.The main target of the adoption of the two-stage classification circuit it naturally to improve the sharpness of size separation. This again leads to the following advantages in the grinding process:- lower circulating load and increased capacity- lower energy consumptionnarrower size distribution in the fine product- less overgrinding and less slimes- reduced specific surface areaThese improvements, no doubt, reflect on the subsequent concentrating process in the following aspects:the rate of flotation is improved, less reagents and energy is neededthe recovery and grade of valuable minerals in concentrates is improved- savings in dewatering can be expected- less fines in tailings improve the conditions for water recirculation."

Jan 1, 1980

By P. K. Narasimharaghavan

The major threat to the sustainability of Aluminium Industry is its significant contribution to global warming by way of generation of non eco-friendly gases during its production cycle from Bauxite to the finished product. Though reduction measures are taken in control and effective recovery of values from pot room gases, efforts in use of environment friendly additives in the final products production line is warranted. In this line, the present paper describes our efforts in the use of a new generation refining flux which apart from helping in effective removal of alkali metals, reduction in inclusions and ensure a better metal cleanliness shall also aide in reduction of obnoxious gases generated during the metal refining process prior to casting. The aim of the current work was to reconcile the practical results with the old generation fluxes used. Further improvements to bring in a better metal cleanliness will also be discussed.

Jan 1, 2010

By Nikolaos Polysos, Holger Witthaus

INTRODUCTION The classification system for German coal mining is the result of approximately 100 years of experience in roadway development and longwall mining. It is also based on different research projects covered by national and European research programs. Over the past 30 years, more then 600,000 m of road-ways have been driven and employed for mining activities. To properly describe the German rock mass classification system, therefore, it is useful to take a look at the main geomechanical preferences and common support systems. The decision about the most effective development technique and support system is based on a synthesis of rock mass classification and geomechanical analysis. The properties of surrounding rock, the in situ stress, and the influence of mining activities in several seams at each German mine must be considered for the evaluation of the expected deformation of the roadway. The mine layout, the requirements of ventilation and fire prevention, as well as the need to maintain emergency escape routes for the miners, require that the gate roads remain usable after the passage of the longwall face in most cases. Moreover, the gate roads must be maintained despite the high stresses that are applied during longwall retreat mining. Therefore, gate road design must address a broad spectrum of potential deformation environments. In the past, when gate roads were supported solely with yielding steel arches, lithologic descriptions of the surrounding strata conditions were adequate for the dimensioning of support and the prediction of the roadway deformation. The current conditions of multiple-seam mining at depths of up to 1,700 m require combined support systems, including pattern bolting and backfilled steel arches. Rock bolt support is used for development, after which (typically 50–100 m outby the face) the steel arches are installed and backfilled with building material (concrete) in order to achieve an optimized development rate. The rock mass classification system described below was developed especially for the conditions of German hard-coal mining. It includes the stress distribution caused by multiseam workings (including crossing goaf edges of former longwalls), as well as in situ stresses due to greatdepth and the presence of tectonic faults. It is based on the evaluation of four parameters: • Geotechnical analysis of drill cores • Geotechnical observation of the development face • Geotechnical classification of tectonic structures (faults) • Standard classification derived from geotechnical assessment and evaluation of stress conditions (using numerical modeling for stress calculation) ROCK STRENGTH One of the most important input parameters for describing strata conditions is the strength of the rock. The German classification system is based on a description of lithotypes. This method has been used successfully since the 1950s and is based mainly on the uniaxial compressive strength (UCS) of the material. An evaluation of the rock strength observed in a survey of approximately 82,500 samples of rock core yielded the results shown in Figure 1. The three most common coal measure rock types are mudstone, siltstone, and sandstone. Each shows a specific mean UCS level and a different spread between the minimum and maximum values. Sandstones, in particular, have a wide spectrum of compressive strength, ranging from approximately 40 MPa to greater than 130 MPa, with an average of 85 MPa. The causes of this wide range include different sedimento-logical preconditions, facies, and digenetic processes. [ ]

Jan 5, 2007

By Abdul Aziz Hanifah

A novel instrumentation and analysis technique, called GLOSTREXT method has recently been introduced for bored pile load tests in Malaysia. This technique provides an innovative and improved alternative for conventional bored pile instrumentation methods commonly practiced for the past few decades. Results for five case histories involving full scale static load tests for high capacity bored piles with both new and conventional instrumentation details placed in within the same instrumented piles are presented to demonstrate the advantages of this novel technique. Results show good agreement between the new and conventional instrumentation.

Jan 1, 2006

By L. Hansen

Sulphuric acid plants now and then see unexpected increases in SO2 emissions. Our experience is that it is not always easy for the acid plants to pinpoint the exact reason for the SO2 increase. Sometimes a catalyst bed is sacrificed even though reliable temperature readings and gas analyses could have verified satisfactory activity. Hence the leaking heat exchanger is never discovered and after the shutdown the SO2 emissions are still too high. This paper will look into some basic catalyst management tools: good record keeping is a necessity for collection of representative catalyst samples; reliable operating data is an inevitable starting point for all analysis; and trending of operating data is a must for plant optimization and troubleshooting. In addition, these catalyst management tools will give continuous updated knowledge of the catalyst status in each bed, providing the basis for a more effective replacement strategy. The most typical reasons for increasing SO2 emissions will be presented together with easy guidelines for cross-checking operating data, temperature optimization and good record keeping.

Jan 1, 2009

By N M. Vegter, C B. Kohler, E H. O Meyer

Zincor operates four Lurgi fluidised-bed roasters at its roast-leach-electrowin refinery in Springs, South Africa. In 2006, Zincor?s four roasters had reached ages ranging between 26 and 38 years, while the expected life of this type of roaster is generally 20 to 25 years. Based on its condition, Roaster 3 was the first to be rebuilt in 2006. Roaster 4 is being rebuilt in 2007 and the last two roasters will be rebuilt over the next few years as necessary. The main damage to Roaster 3 was caused by buckling of the roaster steel shell. This caused the freeboard and dome areas to shift, resulting in cracks in the dome brick lining and crumbling of the bricks lining the freeboard. The steel shell buckled due to the combined effects of too-high operating temperatures and corrosion caused by the following two main factors: ? Thicker external insulation was installed during a previous maintenance shut which resulted in and increased steel shell temperature and exacerbated the normal metal fatigue; ? SO2/SO3 containing gas that had permeated through the brick lining, passed through its dew point during frequent planned and unplanned shuts over the life of the roaster. This caused acid formation between the refractory brick lining and steel shell, resulting in corrosion of the shell. The initial plan was to replace only the damaged areas of Roaster 3, but upon dismantling more damage was found and the roaster was rebuilt from the tuyeres upwards. During the rebuild, the opportunity was taken to modify the design of some of the brickwork to extend its life and make future repairs easier. This paper discusses the mode of failure of Roaster 3 and the lessons learnt during its dismantling and rebuilding.

Jan 1, 2007

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. This volume deals with the development of a microcomputer based training cost model (TCM) which can be used to analyze training cost implications of various types of training. The model has been developed using Aston Tate's dBASE III plus language. The computer program and a test run of the model are presented in this report.

Jan 1, 1993

By W. Tom Witherspoon

Many Engineers are skeptical and cautious about skin friction factors for the portion of drilled piers where temporary casing is used. This has led Texas engineers in many cases to eliminate skin friction values for the cased section, which necessitates deepening the drilled shaft to compensate for the loss in the cased section. This paper has provided field test data that supports inclusion of skin friction in the temporarily cased hole section as a contributing factor in total axial capacity as comparable to open hole shafts of the same diameter. Reasons for the resultant friction values are provided including; remolding of the cased clay section and the increased pier circumference necessitated by the oversized casing required for adherence to the engineers shaft diameter specification.

Jan 1, 2009

By Ray Brainard

The Jollyville Transmission Main will be a 10.5-km- (6.5-mile)-long, 213-cm (84-in.) diameter rock tunnel. The tunnel will pass beneath the Balcones Canyonlands Preserve, which was established to protect two endangered bird species, six endangered cave invertebrates and a threatened salamander. To address the sensitive habitat that the transmission main is to pass through, the city of Austin developed an environmental commissioning (EC) process that brought together environmental engineers and scientists, the city?s project management team and the designer team to work collaboratively to meet the city?s goals of producing a cost-effective design while also protecting the environment. This paper describes the environmental commissioning process and the benefits it brought to the project and environment through some unique environmental mitigation measures to protect this sensitive area.

Jan 1, 2012

By Ray Brandon

The recent introduction of polymer geogrids for ground control purposes in underground mines allows mine operators more flexibility in choosing improved products for several applications. This is evidenced most clearly in longwall recovery operations. Since November, 1994, many mine operators have chosen Fortrac geogrid assemblies for the purpose of securing longwall recovery areas prior to shield removal. Fortrac is a lightweight, strong, and flexible polyester geogrid available in many strengths. Utilizing the "diamond" seaming method, different strengths of Fortrac geogrids are easily fastened together so stronger geogrids may be placed in the most critical areas and lighter geogrids in less critical areas.

Jan 1, 1996

By Alex Doll, Derek Barratt

"There is a number of comminution tests commonly used in the mining industry. Many of the tests are used for a particular grinding model or mill sizing program and are incompatible with other tests of different models. This paper provides an overview of the commonly used grinding and crushing tests, which models (or practitioners) use a particular combination of tests and draws some relationships between the incompatible tests based on the DJB Consultants Inc. database of projects.Case studies will demonstrate similarities and differences between major mining districts with some comments about homogeneous and heterogeneous behaviour within the grindability results.INTRODUCTIONThere are a number of bench-scale grindability tests in use for sizing and predicting throughput for grinding circuits. Part of the reason for this variety is there are a number of different grinding models in use in the Industry, and those models operate using incompatible test results as input (Doll and Barratt, 2008).By using the database of testwork in the DJB Consultants, Inc. (DJB) Millpower 2000 database (see Table 1), some of the more commonly used tests are compared and relationships will be drawn."

Jan 1, 2011

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob.

By E. Chin

The countries of Asia and the Pacific have large resources of diverse minerals. Australia and China have extensive mineralization that are commercially being exploited. The major minerals in Australia with known reserves adequate for both domestic demand and export markets include bauxite, clays, copper, diamond, gold, iron ore, lead, manganese, mineral sands (titanium minerals), nickel, salt, silver, tin, uranium, and zinc. China is the world leader in proven reserves of antimony, barite, magnesite, molybdenum, rare earths, titanium (ilmenite), tungsten, and vanadium. It also has about 55 billion tons of iron ore, albeit with an average grade of only 30 % to 35 % elemental iron content. With the exception of chromium and copper, China has significant resources of a wide array of minerals and metals, based on its production and/or export capability for these commodities. Additionally, India has significant resources of bauxite and mineral sands; Indonesia, bauxite, copper, nickel, and tin; Malaysia, tin and associated titanium; Mongolia, copper, fluorspar, and lead-zinc; New Caledonia, nickel; New Zealand, gold and iron sand; North Korea, magnesite; Papua New Guinea, copper, gold and mineral sands; Philippines, copper, chromite, and gold; and Sri Lanka, gemstones. Moreover, there appears to be extensive mineralization III Burma (Myanmar), Cambodia, Laos, Thailand, and Vietnam, but they have yet to be definitively delineated.

Jan 1, 1994

Important factors in dredge design are the estimation of total head, and the determination of flow in and around suction nozzles and in pipe lines. Total head for the dredge pump is calculated from velocity, static, and friction heads. Flow into suction nozzles depends on whether hydraulic jets or mechanical cutters are used, and on nozzle shape. Design of pipe lines depends on the transportation characteristics of the pulp, skin friction, swirl, and the avoidance of cavitation. Measurement and control of flow is important.INTRODUCTIONEconomic deposits of heavy minerals along the east coast of Australia occur in frontal dunes, which are normally unconsolidated and granular, or in hind dune areas which may contain indurated seams interspersed with loose material. In working frontal dunes, dredging depths are usually shallow since values do not persist for more than a few feet below sea level. However, the controlling factor in dredging the hind dune areas is the level of the water table and suction dredges may be designed to mine to depths of 120 ft, or even more, if necessary.In previous applications of suction dredges in the industry attention was directed primarily towards production and there was only limited research on fundamental techniques. However, with lower grade deposits now forming the major ore reserves, production levels and profit margins will fall unless more efficient dredges are developed.For satisfactory design of dredges it is essential that the total head be accurately estimated and that detailed information of the principles of flow in and around suction nozzles be determined. This paper presents information gained from field experience and laboratory investigation on these aspects.

Jan 1, 1962

A unique sluicing process for recovering tailing impounded in a valley was developed by Electrolytic Zinc Company of Australasia Ltd., West Coast Mines, Rosebery, Tasmania.Earthmoving equipment could not be used as most of the material to be recovered was semi-fluid. A conventional sluking method was also impracticable as there was no suitable working face from which the process could be commenced.Operations started from a flat surface, using special techniques for sinking through the tailing and establishing producing working faces as the sinking process continued.After about 2 years the bottom of the dam was reached and conventional sluicing methods could be used.

Jan 1, 1973