Search Documents

By Theresa M. Bodus

The strength of roof shales is, in part, a function of the preferred orientation of clay minerals within them. Therefore, analysis of clay fabric under both air-dried and hydrated conditions should be helpful in understanding roof shale failure. Core samples were collected from the Energy, Anna, and Lawson shales, which are locally present as roof shales of the Herrin No. 6 coal of southern Illinois. The Clay Fabric Index (CFI) was measured for thirty core samples, using X-ray diffractomtry, to investigate the relationship between clay fabric and roof collapse in coal mines. Greater CFI values indicate a weaker preferred orientation among clay minerals, which generally results in a weaker inter-grain bond. Average CFI values for air-dried samples were: 0.15 for Anna shale; 0.20 for Energy shale; and 0.37 for Lawson shale, .After the introduction of water, average CFI values increased to: 0.28 for Anna shale; 0.22 for Energy shale; and 0.43 for Lawson shale. The laboratory results indicate the following: [l] under air-dried conditions, Anna shale is the most stable, followed by Energy and Lawson shales; and 121 under hydrous (mine) conditions, Energy shale is the most stable, followed by Anna and Lawson shales. In mine environments where roof failures involving Energy shale have occurred, planar trends delineated by a relatively high density of small (0.2-4 cm diameter) iron concretions have been reported along the failure surface. Radial cracks have been observed around unsealed anchor bolt holes in the Anna shale. Instability of the Lawson shale is ubiquitous in coal mines. In the laboratory, similar physical changes were noted in the shale samples after the introduction of water, including [l] increased hydration around the perimeter of iron concretions in Energy shale, [2] radial extension cracks in Anna shale, and 131 extreme slaking of Lawson shale. Measured increases in the CFI reflect the observed physical changes of the samples upon the introduction of water, which probably reflect changes in strength that may result in roof failures in hydrated mine environments.

Jan 1, 1989

By D. K. Bose, R. H. Rakhasia, V. D. Shah, J. C. Sehra

A series of experiments was conducted to determine the effects of roasting temperature, soaking period and quantity of soda ash added. At a laboratory scale, under optimum conditions of roasting at 873 K for 2 700 s with soda ash 10 wt% in excess of stoichiometric, molybdenum recovery was 99%. The investigations indicate the technical feasibility of producing high-purity MoO3 by combining the roasting process with carbon adsorption/desorption. The process uses low-cost chemicals, can be scaled up readily and is free of the SO2 pollution generated by conventional roasting, as the sulphur content of the concentrate is converted to sodium sulphate

Jun 18, 1905

By D. Turk, P. Lefebvre, J. Sargent, K. Major

"Stillwater Mining Company recovers platinum and palladium from their Nye Montana operations. Mining first commenced at Nye in 1987 at a milling rate of 455 t/d (500 stpd). The plant was expanded in 1995 with the replacement of the ball mill and the addition of flotation capacity to increase mill throughput to 1820 t/d (2000 stpd). The applications for platinum and palladium have increased in recent years particularly in the automotive industry and the supply of the metals has remained fairly constant with prices for both platinum and palladium increasing and remaining very stable. In 1997 Stillwater initiated the expansion of their operations to increase production of platinum and palladium. Projects were initiated to expand production at the Nye operations, increase smelter and refining capacities at the Columbus facilities and to develop the extension of the orebody at the East Boulder site. This paper will discuss the changes at the Nye concentrator which were completed to increase production from 1820 t/d (2000 stpd) to 2730 t/d (3000 stpd) and eliminate some of the process bottlenecks.IntroductionStillwater Mining Company is mining the only significant primary source of PGMs outside of South Africa. The J-M Reef is an extensive mineralized zone containing PGMs that has been traced over a strike length of about 43 km (27 miles) in the southwest region of Montana. Stillwater controls the entire PGM mineralized zone.Johns-Manville geologists discovered palladium and platinum in the early 1970’s. In 1979, a Manville subsidiary entered into a partnership with Chevron, USA to develop the project. In 1 987, operations at the Stillwater property near Nye, Montana commenced."

Jan 1, 2000

By Clay Haynes

While the Kansas River Tunnel is a relatively short, small diameter tunnel, the shaft excavation methods implemented were long and large on innovation and use of reverse circulation drilling equipment. ATS Drilling, L.P. used mechanical excavation techniques for both soil and rock segments of the 42.7 m (140 feet) and 38.1 m (125 feet) deep shafts that were 2.9 m (9.5 feet) and 4.1m (13.5 feet) diameter, respectively.

By T. J. Yeomans

"The Kidd Creek metallurgical site is situated twenty-six kilometres east of Timmins, Ontario. The site consists of a 4.5 niillion tonne per year concentrator, a 127,000 tonne per year electrolytic zinc plant and a 79,000 tonne per year copper smelter/refinery complex.The concentrator commenced operations in 1966 and was expanded to its present capacity in 1978. The zinc plant commenced operations in 1972, and the copper smelter/refinery in 1983.The concentrator tailings, and both liquid and solid waste products from the other plants are disposed of within a 1215 hectare tailings disposal area. Here, a method known as centraljzecl thickened discharge is used to form a stable cone-shaped hill. A low permanent perimeter dyke structure encloses the cone and directs cone run-off and thickener overflow to a treatment pond. After treatment with lime slurry, this neutralized effluent is recycled to the metsite and also discharged into the Porcupine River system.The tailings system has been in operation in its present form since 1972, upon completion of dykes and a 110 metre thickener unit. Underflow densities were continuously increased until thickener overloading became a serious problem. This necessitated the construction of a second 110 metre thickener, which was completed in 1983. Target densities have been achieved without difficulty since then.This paper discusses the operation of the tailings system, reviews past performance, and outlines future operations."

Jan 1, 1986

The Australian Coal Combustion Testing and Research Facility has been operating commercially for one year and during that period coal product evaluations have been conducted on behalf of four coal companies and one electricity commission. The facility is equipped to assess the behaviour of steaming coal in milling, combustion (including flame stability, burnout and heat transfer), ash deposition and erosion, fly ash collection and gaseous emissions. The relevance of the results of the pilot testing to industrial practice was demonstrated during the calibration of the facility using four coals burnt in Australian power stations. The calibration coals were from the Tarong and Gladstone Power Stations in Queensland, tluja Power Station in Western Australia and Bayswater Power Station in New South Wales. Also an opportunity arose to visit an overseas power station to observe a full scale test burn using one of the early coals tested on a commercial basis in the combustion test facility. The calibration trials showed excellent agreement with industrial coal performance in t:orms of flame stability, turndown, carbon burnout and gaseous emissions. Encouraging correlations were also found in the case of furnace radiation, boiler deposits (slagging and fouling) and electrostatic precipitation. In the case of the last group the only real reservations about the correlations are due to the non-availability or qualitative nature of results collected around the power stations. In all cases there is a high degree of confidence in the facility's ability to predict the relative performance of different coals and in some cases direct numerical predictions can be Made.

Jan 1, 1987

By R. Kanniganti

The primary problems of pillar design in seams subject to interaction are due not only to difficulties in predicting loading, but also to the often unsymmetrical nature of the stress fields. The effects of uneven stress fields on failure patterns within a pillar were studied wing a two dimensional finite element method. Lower seams, including ultra- close mining situations were evaluated considering conventional pillars. Pillar case study data for under mining were analyzed to determine if empirical trends in stable pillar sizing could be derived. Recommendations for multi-seam pillar design are made, based on anticipated loading conditions within a pressure bulb. Applications of the research results are demonstrated using case studies

Jan 1, 1995

By E Ah Mu and C R Lilley, A D. Campbell

Cave propagation is a complex process due to interacting variables such as mine geometry, rock mass heterogeneity and complex structural networks and stress fields. The Ernest Henry sublevel cave (SLC) is directly below an open pit, which provided an opportunity to observe and measure rock mass failure as the cave initiated and propagated through the pit wall. This paper describes interaction between the open pit and SLC as well as rock mass failure mechanisms observed from the start of the SLC to surface breakthrough.Cave propagation and slope failure mechanisms were found to be governed by intermediate structures, while the cave shape was largely controlled by cave-scale faults. The open pit, production-level geometry and production draw strategy were also important factors for cave and subsidence growth. Cave propagation was episodic and asymmetric in shape due to the orientation and relative position of geological structures, combined with the effects of the increasing SLC geometry and drawdown from the underlying production levels. The precursors and failure mechanism of a 2.5 Mt wall collapse are also reviewed in detail.Cave growth was simulated using a 3D, non-linear, discontinuum finite element model coupled with Newtonian Cellular Automata. Model results are compared to field observations and monitoring data to determine the accuracy of forecasts and compared models versus actual rock mass response during cave propagation.CITATION:Campbell, A D, Ah Mu, E and Lilley, C R, 2016. Cave propagation and open pit interaction at the Ernest Henry Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

[ ]

Jan 1, 1938

Jan 1, 1964

By Dupuy. Leon W., R. T. C. Rasmussen, W. A. Calhoun

"INTRODUCTION For many years it has been known that low-grade manganese deposits occur in the bluffs along the Missouri River Valley. Frequent attempts have been made to develop the ore and to produce a marketalble commodity but they have had little success. Under pressure of the war emergency and the shortage of manganese, the attention of the Federal Bureau of Mines was directedtoward the deposits.Manganese-bearing shale occurs from a point near Pierre, S. Dak., down the river to the Rosebud bridge near the Nebraska line (1).5/ The Bureau of,confined its work to the more accessible central portion of the deposits near Chamberlain, S. Dak. The ore occurs principally as concretionary nodules in the form of iron and manganese carbonates (manganosiarite and perhaps some manganocalcite; rhodochrosite has not been identified). At the surface the carbonate is often broken down so that the oxide of manganese gives the nodules a black The matrix or host rock is generally known as Pierre shale, composed of ""interbedded layers of bentonite, an altered volcanic ash, and dissemi¬nated bentonite particles,"" (2) and montmorillonite-beidellite clay minerals (3). The shale weathers to the very sticky gumbo characteristic of South Dakota and well-known to hunters and travelers in the area.The area selected for the experimental mining and pilot-plant work discussed in this report lies about 8 miles westerly from Chamberlain and is a few hundred feet north of U. S. Highway,16, on land owned or controlled,by M. Q. Sharpe of Kennebec, S. Dak., and the General Manganese Corp."

Feb 1, 1946

This Bureau of Mines publication presents an overview of mine electrical power systems research currently being conducted by the Bureau. The papers, given at a Technology Transfer Seminar, emphasize the increasing importance of research related to the safety considerations of underground coal mine electrical systems. Selected topics are included that summarize results of research in the areas of electrical shock prevention, explosion-proof enclosures and load centers, discriminating circuit breakers, and trailing cables. Other topics discussed at the seminar are published as separate sections of the Bureau of Mines Hand- book "Application Notes--Mine Electrical Power Systems."

Jan 1, 1982

The largest investment in mining equipment in Caterpillar?s history ? The F series mechanical and electrical drive trucks ? is rapidly advancing. Caterpillar showcased the 793F and 797F mechanical drive trucks and the 795F ac electric drive truck at MinExpo in 2008 and have continued testing since then. The 793F and the 797F have accumulated more than 75,000 hours of field testing and have proven their performance capabilities and their durability. The new Cat C175 engine that powers them has racked up 130,000 hours of field testing in mining trucks and more than 120,000 hours in power systems. Because of the success of these field-follow programs, the 793F is targeted to go into full production within a few months and the 797F late this year. Caterpillar engineers have been testing two 795F ac prototypes at the Tucson Proving Grounds in Arizona. The development program has provided input for the construction of a new 795F ac in Decatur, IL. The new truck recently shipped to a copper mine in North America where it will serve as the first field-follow 795F ac as it works at the mine. The 313-t- (345-st-) capacity 795F ac will enter a new size class for Caterpillar, and, as a result, the primary focus of the Caterpillar ac electric program has been on the 795F ac. The commercial launch date will be defined as the field-follow program progresses. ?It?s fitting that soon after producing the 50,000th Cat off-highway truck, we are now shipping our first ultra-class ac electric drive truck to a mine,? said Chris Curfman, president of Caterpillar Global Mining. ?Our new trucks further solidify our position as the one manufacturer to provide unparalleled options and unmatched customer support.?

Jan 1, 2009

By Y. Ichihara, H. Matsumoto, K. Itakura, H. Eguchi, G. Deguchi, K. Sato

Mechanical data from a rockbolt drilling machine, such as torque, thrust, revolution and stroke, are useful for understanding the geological and geomechanical conditions around roadways and hence selecting the optimum bolt type and density. Laboratory experiments showed that the level of torque or thrust reflects differences in rock type, with separation of strata and cracks appearing as a specific pattern. Algorithms of neural networks based on adaptive resonance theory and back-propagation were used to extract the pattern and estimate the location of discontinuities. For field testing in an underground coal mine, a prototype data acquisition system was attached to a portable drilling machine. Several sets of logging data from one locality were combined to construct a two-dimensional model of the strata, from which the slope angles of discontinuity faces could be estimated

Jun 19, 1905

By Robert Martin, Brian W. Stump, David P. Anderson, W Scott Philips

Since 1994, various mines in the US have cooperated with research scientists at the Los Alamos and Lawrence Livermore National Laboratories to address issues related to verification of the Comprehensive Test Ban Treaty (CTBT). The .CTBT requires that no country may conduct any nuclear explosion in the future. While the CTBT is a significant step toward reducing the global nuclear danger, verifying compliance with the treaty requires that the monitoring system be able to detect, locate and identify much larger numbers of smaller amplitude seismic events than had been required previously. Large mining blasts conducted world-wide will be of sufficient amplitude to trigger the monitoring system at the lower threshold. It is therefore imperative that research into the range various blasting practices employed, the relationship of yield to seismic magnitude, and identification of anomalous blasting results be performed. This paper will describe a suite of experiments funded by the Department of Energy and conducted by the Los Alamos and Lawrence Livermore National Laboratories in cooperation with the US mining industry. Observations of cast blasting, underground long wall generated coal bumps, stoping, and explosively induced collapse of room and pillar panels will be presented. Results of these dual use experiments which are of interest to the mining community will be discussed. These include 1) variation of amplitude of seismic energy at various azimuths from cast blasts, 2) identification of the extent of back failure following explosive removal of pillars, and 3) the use of single fired shots for calibration of the monitoring system. The wealth of information and discovery described in this paper is a direct result of mutual cooperation between the US Government and the US Mining Industry.

Jan 1, 1997

By J Williamson, M Griessmann

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Watershed tungsten deposit is located in the Hodgkinson Province of north Queensland, Australia. The deposit is hosted by Siluro-Devonian flysch-type meta-sediments of the Hodgkinson Formation, which were subjected to four major deformation events. Mineralisation has occurred syn- to post-D4 and is related to the intrusion of S-type granitoids of the Permian Whypalla Supersuite.Watershed is located within a regional NW–SE-striking melange zone composed of brecciated and intermixed arenites and shales. The major NW–SE-striking Tullah fault zone is situated in close proximity to the east of the deposit.The Watershed deposit occurs within a tightly folded upright anticline with NW-plunging fold axis. The anticline contains a major package of coarse-grained to conglomeratic arenite, which harbours the Watershed mineralisation. Several alteration styles occur within the arenites, of which Fe-poor calc-silicate alteration dominated by clinozoisite/epidote is the most significant. Less widespread but locally important alteration styles comprise garnet-dominated calc-silicate alteration, albitisation and sericitisation. The arenites are enveloped by unmineralised carbonaceous shales and shale breccias.Tungsten mineralisation occurs solely as molybdenum-poor scheelite and can be found as three styles: disseminated mineralisation in calc-silicate altered arenites, vein-style mineralisation with quartz-albite-scheelite veins and minor but high-grade mineralisation in albitised felsic dykes.Contact metamorphic rocks and geophysical data indicate the proximity of an underlying granitic body. It is believed that this granitic body was the main driver of the hydrothermal system generating the Watershed deposit. An early mineralisation stage caused the selective calc-silicate alteration of the arenites, while a second stage caused the vein-style high-grade mineralisation. The folded shales enveloping the arenites worked as an effective barrier that kept the mineralising fluids in a confined rock volume.The scheelite mineralisation at Watershed is open to depth, with a granite-hosted porphyry or greisen-style mineralisation anticipated below the current resource.CITATION:Griessmann, M and Williamson, J, 2015. The calc-silicate-hosted Watershed tungsten deposit, far north Queensland, Australia , in Proceedings PACRIM 2015 Congress, pp 545–550 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By R. B. Booth, W. F. Linke

The continuous interest of the American Cyanamid Company in producing superior polymeric flocculants and dispersants for the mining industry has resulted in a broad, general study of the physical chemistry of mineral-polymer systems. The aim of this program has been to establish a sound theoretical basis on which practical problems could be analyzed, and which would lead to the development of new and improved flocculating and dispersing agents. This study has required the cooperative effort of physical, analytical, and polymer chemists, as well as engineers familiar with mining problems. This report summarizes the results of some of our investigations over the past two years. Further studies along these and other lines are in progress and will be reported in the near future. MEASURING FLOCCULATION IN THE LABORATORY The foremost problem in studying flocculation in the laboratory has been to establish reproducible methods of comparing and evaluating the effectiveness of various reagents. Previous workers have measured settling -rates 1,8 filtration rates2 , and sediment volumes3 . Direct observations of the floc size, or the clarity of the supernatant liquid, can also be used. AIthough these parameters are all interrelated, they do not always measure the same physical properties of the suspensions, and hence are not equally useful or reliable. Whatever the method of comparison selected. the testing procedure must be carefully defined and standardized. The results must be satisfactorily reproducible, and for practical purposes must accurately reflect the results obtained in mill use. In order to compare the data obtained in these various types of test, the physical nature of the flocculated system must be examined in some detail. In an unflocculated system, only the larger or denser particles (the "sands") settle at a useful rate. The sediment can be observed to build up from the bottom of the cylinder, while the fines remain in suspension for a long period of time. If the system is not disturbed, even the microscopic fines can be seen to classify themselves as they fall over a period of days. When a high molecular weight polymer is added to the system, the colloidal particles are tied together randomly in flocs, and the sands and fines settle together. The line of demarkation between solid and liquid phases moves downward from the top of the cylinder. The settling rate of the flocs depends on their size and on their effective density. For a given mineral sample, the larger the flocs, the faster the settling. Since the large flocs cannot pack as closely as small ones, they produce a sediment with more pore spaces, and hence of larger volume, which is easier to pump and to agitate. Although it is nearly impossible to measure individual floc sizes, it is relatively easy to determine settling rates and sediment volumes. Of these two, the settling rate is simpIer to measure, and hence generally more practical. Reproducible sediment volumes can only be obtained by allowing the solids to pack for a rather long period of time (e.g., hours to days), and although the volumes thus observed are directly related to the degree of flocculation (average floc size), it is often impractical to wait so long for the results.

Jan 1, 1961

By D. E. FOCG, A. E. Wells

When the United States entered the World War governmental agencies found little definite knowledge available as to the exact capacity of each sulphuric acid plant in the United States to manufacture acid under the stress of a great emergency. It is true that on account of the demand for acid for the manufacture of munitions for the Allies, prior to the entrance of this country into the war, most of the acid plants near industrial centers in the Eastern and Northern States were running at or nearly their maximum capacity, but, . for various reasons, many plants in these States and plants in other districts were not. For a number of years statistics as to the production of acid by the plants of the country were compiled by the United States Geological Survey, but obviously such figures did not give information as to the maximum capacities that might be available for meeting the he.a vy war ·requirements, or as to the steps that would have to be taken to bt-ing these capacities into use. During the summer and early fall of 1917 various attempts were made to obtain the desired information, but no satisfactory or complete data were obtained. Late in 1917, under the authority granted to the Bureau of Mines by the explosives act, the Director of the Bureau of Mines directed A. E. Wells, metallurgist of the bureau, to uiake a complete survey of the situation. Mr. Wells personally conferred with officials of the acid companies and visited most of the acid plants in the North that are east of the Mississippi River. The information obtained through this personal survey, together with that obtained through the ready cooperation of the subcommittee on ncids, and the subcommittee on fertilizers of the Committee on Chemicals of the Council of National Defense, enabled the preparation of a report containing the desired data concerning the sulphuric acid industry. This report was made immediately available to the War Industries Board and to those offices in the War and Navy Depart- ments that were most directly concerned in planning the explosives program and in obtaining the necessary supplies to produce the explosives. Beginning with this survey and report, the sulphuric acid section of the war minerals investigations of the Bureau of Mines took an active part in all matters pertaining to the sulphuric acid industry during the remainder of the war. Mr. Wells, the chief of the section, was appointed an associate chief of the sulphur, pyrite, and sulphuric acid sections of the War Industries Board. .Also, by this direct contact with the War Industries Board, the data obtained by Messrs. R. R. Hornor, H. A. Buehler, a.nd 0. Lindstrom, who were in charge, for the bureau, of the investigations concerning the supplies of pyrite and sulphur, were constantly made available to all interested Government agencies. D. E. Fogg, of New York City, was appointed chemical engineer to the sulphuric acid section to make special investigations relating to the acid industry, especially the possible utilization, in an emergency, of those sources of raw material.not then being used. Mr. E. E. Corbett, of Brooklyn, N. Y., was appointed chemical engineer to make investigations concerned primarily ,vith the conservation of acid. Direct and intimate contact with the industry was had through the close cooperation with the committee on acids of the Chemical Alliance, this committee during the greater part of 1918 occupying rooms with the acid section of the bureau. With the ending of the war and the close o:f the active work of the acid section of the bureau, the suggestion was made by many interested parties that a bulletin be prepared giving some qf the fun. damental and most important facts regarding the sulphuric acid industry, including a discussion of the technical :features of the manufacture of acid. During the war the bureau received -a vast number of inquiries in regard to various phases of the industry, a.nd this fact also made such a bulletin seem desirable. Therefore, the present bulletin was prepared to cover the main facts in regard to the industry in this country, including a discussion of the supplies of sulphur-bearing raw materials, the situation of the acid plants, the principal points in regard to manufacturing processes, and the uses of the acid. No attempt has been ma.de to discuss at length the manufacturing processes, as details differ more or less at the different plants and in general are carefully guarded by the acid ·companies. A great deal of the data given in this bulletin may be found in various pub]ications, but this is the first publication in which such data have been assembled and made readily available. Most of the data were obtained directly from observation and from cooperating acid companies or from individuals who had been or are now engaged in acid manufacturing and were liberal and generous in making their information available for publication. Care has been exercised to publish no data that were obtained as confidential by the bureau's representatives. The average acid manufacturer may be already more or less acquainted with most of the information presented in this bulletin, yet it is believed that the bulletin will be of value to those who wish to obtain a. general review of the present condition, both the economic and technical, of the sulphuric acid industry in the United States.

Jan 1, 1920

By Kevin Connor

There was little change during 1988 in the production of minerals in Burundi. The Government of Burundi, which banned all commercial mining operations in the country in 1979, lifted the ban on mining of alluvial gold deposits and started a program of small-scale artisan gold mining in October. Along with the legal mining of gold, licensed gold trading counters were established. Other mineral commodities produced were kaolin clay, lime, and peat. In compliance with the Government ban, the only mineral wealth exploited for commercial sale and export was alluvial gold. Through financial assistance from the International Bank for Reconstruction and Development (World Bank) and the United Nations Development Program (UNDP), a study to inventory the country's mineral resources continued throughout the year. As part of this study, during the year, a West German company undertook a drilling program to further outline the nickel reserves of the Musongati area in central Burundi. Results of the work as of yearend were disappointing, with only 12 million tons of ore identified with better than 2% nickel content proven. Investigations also continued during the year regarding the centrally located deposits of vanadium-bearing titaniferous magnetite. A Norwegian company contracted to prepare a prefeasibility study for developing the deposit. The British Sulphur Corp. Ltd. was nearing completion of its $1.2 million2 study of the phosphatic limestone deposit at Matongo-Bandaga at yearend. Ore reserves of about 17 million tons grading 11% phosphorus pentoxide (P2O3) had been identified. The phosphate zone overlies a carbonatite rock, which could provide the basis for a cement industry. Additional drilling was planned for 1984. Exploration for gold was underway in 19S3 in northern Burundi through UNDP funding. Several primary deposits of shallow semimassive sulfides with gold values ranging from traces to 11 grams per ton had been discovered. With assistance from the Federal Republic of Germany, bastnasite reserves of 5,400 tons, with associated high europium oxide and cerium content, were verified, and the prospects for finding

Jan 1, 1985

By R. J. Schafer-Frentz, T. G. Joseph, M. Curley

"Greenhouse gas emissions—specifically of carbon dioxide—are a concern in Canada, where industrial sectors such as mining are stringently regulated for carbon release. Cumulative emissions are positively related to fuel consumption, which is controlled by several factors. This study investigates one of these factors: the product of vehicle speed and running surface total resistance (TR; sum of rolling resistance and grade resistance). Results show that TR directly affects fuel consumption and emissions—a relationship that is mathematically predictable. Fuel consumption and emissions, which are principally associated with the durability or deterioration of wearing course materials, were analyzed to aid selection of road construction capping material of low rolling resistance. In the oil sands region in the province of Alberta, ground conditions change seasonally. Therefore, the annual fuel consumption for the same wearing course material was also compared. Results demonstrated that haul truck size was a contributing factor, but vehicle speed and TR more strongly influenced fuel consumption and emissions. ¦ KEYWORDS Carbon dioxide, Emissions, Fuel consumption, Grade resistance (GR), Greenhouse gas (GHG), Haul truck, Rolling resistance (RR), Total resistance (TR) RÉSUMÉ Les émissions de gaz à effet de serre (GES), et particulièrement celles de dioxyde de carbone, sont un problème au Canada, où les secteurs industriels tels que l’exploitation minière sont rigoureusement réglementés pour leurs émissions de carbone. Les émissions cumulées sont indéniablement en lien avec la consommation de carburant, qui est contrôlée par plusieurs facteurs. Cette étude examine l’un de ces facteurs, à savoir le produit de la vitesse du véhicule et de la résistance totale de la surface de roulement (la résistance totale, ou RT, est la somme de la résistance au roulement et de la résistance due aux rampes). Les résultats montrent que la RT affecte directement la consommation de carburant et les émissions, un lien qui est mathématiquement prévisible. La consommation de carburant et les émissions, qui sont principalement associées à la durabilité ou la détérioration des matériaux composant la couche d’usure, ont été analysées afin de contribuer à la sélection de matériau de recouvrement pour la construction de routes ayant une faible résistance au roulement. Dans la région des sables bitumineux de l’Alberta, les conditions au niveau du sol changent à chaque saison. Ainsi, la consommation annuelle de carburant pour le même matériau composant la couche d’usure a aussi été comparée. Les résultats ont montré que, si la taille des camions de transport est un facteur déterminant, la vitesse des véhicules et la RT influencent davantage la consommation de carburant et les émissions. ¦ MOTS CLÉS camion de transport, consommation de carburant, dioxyde de carbone, émissions, gaz à effet de serre (GES), résistance au roulement, résistance due aux rampes, résistante totale (RT)INTRODUCTION In Canada and around the world, global climate change has become a topic of great concern and discussion. Pres-sure on world leaders to quickly reduce their carbon footprint is prevalent, prompting new standards and regulations in various industries, including mining and oil and gas. In 2017, the Government of Alberta implemented a carbon tax. The majority of mining activities in this province are truck-shovel operations, where a large fleet of ultra-class trucks is loaded by shovels. Ultra-class haul trucks, classified as those with a capacity of 218–363 tonnes (t), emit high levels of carbon as they travel to processing entry points and waste dumps as designated by the mine plan and mine dispatcher. Mined ore and waste is typically moved over two 12-hour shifts per day throughout the year."

Jan 1, 2019