Search Documents

Due to highly competitive international coal markets, Stockton mine is bound to produce very high quality coals consistently if it is to maintain and expand its market share. The nature of the deposit is such that coals from various source pits are blended in differing proportions to meet the various coal quality specifications of the customer. The complexity arises due to quality variation within the seam both horizontally and vertically and the fact that up to six different products with completely different quality specifications may have to be produced. With increasing demand for this rare product and with CoalCorp eager to meet this demand comes the requirement for computer methods to handle this highly complex problem of both modelling and scheduling.

Jan 1, 1989

By Anil K. Ray

This paper discusses in situ studies conducted at an Illinois Basin room-and-pillar coal mine to evaluate the performances of three different types of bolts under similar geologic conditions. The bolt types considered were the fully grouted passive rebar (FGPR), the resin-assisted mechanical anchor (RMAB), and the fully grouted tension rebar (FGTR). During the evaluations, the three types of bolts were installed in a single entry covering a span of three contiguous pillars with almost identical geologic conditions. The performances of the three types of bolts were investigated by instrumentting the bolts prior to installation as primary supports on cycle. Additional data on roof behavior was collected with extensometers and shear meters placed near the instrumented bolts. Excluding some time lapse right after installation, the performance evaluation of the three bolt systems was based on the data collected for over a year. Based on this study, it was found that the axial loads measured in the different bolt types did not show any identifiable patterns under the prevailing geological conditions at the mine. Therefore, the assumption that active bolts must be superior to passive ones is not always valid. Even though the studied mine did not have any thinly laminated, weak rocks in the immediate roof, the passive bolts performed as well as the active systems.

Jan 1, 2012

By Reda M. Bakeer

"Measurements obtained during load testing of two steel H-piles driven at a site in Northeastern Mississippi are discussed. The general site conditions, equipment used, testing procedures and results of the pile load tests are presented. Both piles were tested in compression and one of the piles was subsequently tested in tension. The piles were instrumented with strain gauges and extensometers to measure the mobilized soil resistance and pile movement. Three different “zero strain” conditions were used to determine the mobilized soil resistance and residual loads due to driving or a load cycle. It was concluded that the effect of residual loads on driven piles could be significant. Driving residual loads influenced the magnitude and distribution of the load transfer curves more than those due to a load cycle. Results of the tension test were impacted by the residual loads from the previous compression test performed on the same pile.INTRODUCTIONSeveral factors affect the performance of a deep foundation system including the subsoil conditions, loading settings, pile type and installation method. Residual stresses develop in piles particularly due to pile driving, but they are typically not accounted for in the analysis (Fellenius 2002). Siegel and McGillivray (2009) presented an assessment of residual loads measured during load testing of instrumented auger-cast-in-place (ACIP) piles. The magnitude and distribution of residual stresses along the pile shaft and toe depend on the pile installation method, previous load cycles and time effects. Poulos (1987) reported that residual load due to driving at the pile toe is independent of pile driving equipment and may significantly affect the results of a pile load test. Hunter and Davisson (1969) reported results of pile load tests performed in compression on fully instrumented piles driven in cohesionless soils along with a discussion of the effects of residual loads. Tension loads of about 445 kN (100 kips) were measured at the pile toe after driving. Unloading residual compression load at the toe was detected as “apparent” tension since the instrumentation was zeroed prior to the test. The researchers suggested a graphical approach to obtain the “corrected” load distribution curves considering that residual load will dissipate following the tension test. Holloway et al. (1975) conducted a study on the effect of residual stresses due to pile driving and developed a computer software that accounts for residual loads. Briaud and Tucker (1984) suggested a method to account for residual loads based on the results of 33 pile load tests performed in mostly cohesionless soils."

Jan 1, 2017

The pyrite-sphalerite-galena and barite orebodies at the Rosebery mine are concordant with the shale host rock and have been deformed into one system of folds with an associated axial plane cleavage. The folds are tight and overturned with east-dipping axial planes. Folds in the sulphide ore are commonly disharmonic, particularly between adjacent bands of different composition.Concentric style folds occur in the competent bands, e.g. pyrite-rich bands. Similar style folds are predominant in the less competent sphalerite-galena-rich bands and also in the shale of the host rock. The trends and plunges of the fold hinge-lines are variable but axial planes are of reasonably constant orientation throughout the mine area. The folds in the orebodies are of limited axial extent, approximating to conical folds, and are arranged in en echelon patterns. The fold system was possibly formed in one period of folding by heterogeneous strain that may have been caused by the presence of a mass of tectonically mobile sulphide ore. Lineations parallel to the ore/host rock contacts appear to reflect movement between the ore and the host rock during folding.

Jan 1, 1972

By C. Restarick, R. G. Robins, R. M. Taylor, I. Ennis

Lime addition to acid mine drainage waters (AMD), possibly accompanied by aeration, has been the basis for their remediation by precipitation of predominantly metal hydroxides. An efficient novel alternative technique causes precipitation of double M(II)-M(III) hydroxy sulfates which readily precipitate and are easily dewatered. When the Fe(II)/Fe(III) + Al(III) ratio of the AMD is appropriate, the Green Precipitate (GP) Process provides a more effective alternative to normal liming/aeration. The process can be adapted to give a continuous in-line treatment by the choice of suitable computer-controlled reactors designed to improve the liming efficiency, reduce scaling and control the rate of treatment. The processes are described in terms of the chemistry involved.

Jan 1, 2000

By H Bibby

Initial analysis of Long Offset Time Domain Electromagnetic (LOTEM) data has traditionally been made in terms of early and late time apparent resistivities. By using more than one grounded bipole as a source, a tensor analysis technique analogous to the method used to analyse DC resistivity multiple-source bipole-dipole surveying may be formulated. We define the æinstantaneous apparent resistivity tensorÆ as the tensor that relates the total electric field vectors at each instant to the steady state (DC) uniform half space current density vectors due to each source. Instantaneous apparent resistivity tensors calculated for a 3D resistivity model suggest that profiles of LOTEM measurements across simple 3D structures can be used to create an image that reproduces the main features of the subsurface resistivity. Where measurements are distributed over an area, maps of the tensor invariants or the tensor ellipses at different times can be made into a sequence of images which provide a way of ætime slicingÆ down through the target structure.

Jan 1, 1996

By Len Harris

Webster?s Dictionary describes culture as: ? The totality of socially transmitted behavior patterns, arts, beliefs, institutions and all other products of human work and thought typical of a population or community at a given time. ? A style of social and artistic expression peculiar to a class or society. ? Intellectual and artistic activity. ? The art of developing the social, moral and intellectual facilities through education. The authors have nearly 100 years of combined experience in the mining industry working with and consulting to mining companies and companies engaged in the supply of goods and services to the mining industry worldwide. In this report, they present their experiences and ideas on the importance of cultural aspects in the successful development and implementation of mining ventures. Their suggestions on how to handle culture shock will be of interest to expatriate managers, operators, social workers, and engineering and construction personnel posted to overseas operations, as well as to nationals posted to other parts of their own country.

Jan 1, 2008

Computer applications are ideally suited to the day to day operations of grade control and short term planning on a mine site. By refining this part of the operation there is scope to increase profits by more accurately predicting ore grade and tonnage, and allowing the mining engineer more flexibility in his approach to scheduling. Large numbers of blasthole or ditchwitch samples need to be processed in a fast and efficient manner, and stored in a database for future reference. The mining engineer has to calculate tonnages and subdivide the blast or digging area into mineable areas of waste, low and high grade ore. New grade and tonnage information must be used by the mining engineer to update his short term plan. Answers must be obtained quickly and efficiently, but a high level of individual input is necessary in order that maximum use is made of the information. Geostatistical analysis of samples can be used to refine the interpolation techniques. Reconciliation between the original grade model, the newly sampled area, and the final product should be monitored continually.

Jan 1, 1989

By Gordon Chen

The Block 37 Chicago Transit Authority (CTA) Tunnel Construction Project was originally designed by STV to connect Blue Line subway in North Dearborn Street and Red Line subway in State Street in the downtown Chicago Area. The project was proposed using tunnel mining techniques combined with steel pipe jacking and fiber glass rebar soil reinforcement. Weidlinger Associates, Inc. (WAI) and Kiewit Construction Company proposed an alternate design using open cut construction technology. WAI designed a complex temporary excavation support system using Soldier Pile Tremie Concrete (SPTC) walls and Soldier Pile Lagging walls supported by cross lot/corner bracing elements. Below the top of the existing tunnel, a top-down construction technique was utilized. A steel temporary traffic decking system at top of the excavation site served as the daily street traffic function as well as the first level of bracing for the support of excavation. The project encountered great challenges of soft clay conditions in downtown Chicago, numerous existing utilities in the excavation site and the requirements of protection for a number of historical buildings nearby as well as the protection of the city streets. The construction was successfully completed at both State Street/Washington Street and Dearborn Street/Randolph Street. The monitoring system showed that ground movement and adjacent building settlement was kept to a minimum during construction.

Jan 1, 2009

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By D. Harrington

Along with other phases of mining , the ventilation of metal mines has been affected by the business depression of 1930. As might be expected , some of the results are favorable , and some are distinctly disadvantageous to progress . Probably the worst effect of the recession of mining activity is that , as usual , one of the first departments of almost any industrial establishment ( and this is especially true of mining ) to be curtailed is that which concerns what might be called welfare work , such as safety , health , etc. , and ventilation : in consequence , a number of men who were employed mainly on ventilation work in metal mines are now out of employment and their former duties either are being handled by others as only part of a crowded routine or are being allowed to lapse . On the bright side of the picture is the following paragraph from a letter by the ventilation and sarety engineer of the United Verde Copper Co. , Jerome , Ariz . , indicating that money and effort expended on ventilation during " flush " times give results which aid in money savings when depression comes : The desirability of absolute control over the ventilation system has again been demonstrated at this mine . Under full operation we have been using approximately 500 hp . to drive our big fan . Under curtailed operations we naturally do not require as much air , so by sending the air only where needed and airing out all other places periodically to keep timber , etc. , in good condition we have been able to economize in the quantity of air required . The fan speed has been reduced and the power dropped to 300 hp . , thus effecting a material saving in the power bill , and still maintaining an efficient ventilating system . "

Jul 1, 1931

The mercury, gold, silver, copper, lead and zinc values of soils over altered and mineralised rock were determined to establish the potential use of mercury as an indicator element in geochemical prospecting. The results are presented to show that mercury can be used successfully in prospecting for precious metal mineralization in the Thames-Waihi area.

Jan 1, 1979

By Mark Rybak

On Aug. 31, 2006, Tropical Storm Ernesto hit the city of Richmond, VA. The Battery Park area was hit particularly hard, as flooding forced an evacuation of the area. A large sinkhole collapsed a sewer line in the Battery Park area, blocking the pipe and causing more serious flooding. This article describes the fast track design, bidding and construction of an emergency tunnel to bypass the collapsed sewer. Innovative value engineering, tunneling and shaft-sinking methods and final lining design all contributed to the success of this project. The storm inundated Richmond, VA with up to 305 mm (12 in.) of rain that, in some areas, caused widespread flooding and damage. One of the hardest hit areas of Richmond was Battery Park. A major trunk sewer in the Battery Park area collapsed and caused local combined sewer and stormwater flooding. The collapsed sewer was a 2.4-m x 76-mm (8-ft- x 3-in.-) wide by 2.7-m- x 152-mm- (9-ft- x 6 in.-) high arch sewer that was constructed in the 1920s and later filled over with municipal solid waste and a soil fill cap to cur-rent elevations. A sinkhole was created in the area of collapse approximately 18 m (60 ft ) deep and 31 m (100 ft) in diameter. This caused the existing arch sewer to become blocked. As a result of this blockage, contaminated floodwaters reached depths in low-lying areas in excess of 8 m (25 ft).

Jan 1, 2008

Trends in Test Filtration to Respond to Decreasing Sample Size There has been a steady decline in the quantity of samples available for testwork when developing new mining processes due to the maturing mining technology and the increasing costs of pilot testing. Larox, a supplier of filtration equipment and its co-operation partner Lappeenranta University of Technology (LUT) have been actively developing new equipment, testing methodologies and tools to plan test campaigns with the objective of being able to determine the optimum filtration technology and the parameters for sizing full scale equipment with a minimum sample size. With smaller sample sizes, the test scale diminishes from pilot scale to bench scale, and the small equipment size has implications for scale-up. Redesigning the equipment to simulate full scale equipment rather than to match filtration theory has led to some interesting developments. Comparisons between bench scale equipment and production units help identify the limitations of bench scale testing. The nature of filtration is such that it is unreliable to estimate filterability theoretically, and different testing methodologies have been investigated to be able to test the feasibility of filtration from samples as small as few grams. While not optimising the filtration technology, these methodologies provide an adequate level of accuracy for scoping studies. Together with improvements in equipment, a software tool has been developed to reduce the number of tests necessary to optimise filtration technology and parameters for sizing.

Sep 13, 2010

A variety of cement raw materials occur within the Cenozoic sequence in Northland. These form the basis of Golden Bay Cement's cement manufacturing operation at Portland, Whangarei. High grade limestone is taken from the Whangarei Limestone formation, which has been shown to have been sub-aerially weathered and developed mature karst features prior to deposition of the overlying allochthon sediments. In this instance, remobilisation of allochthon sediments following uplift and erosion is inferred. At Portland Quarry, argillaceous limestone is extracted from deformed thrust sheets in the allochthon sequence. Quarry operations have been designed to handle the steep asymmetric folds, thrust faults and fracture zones that affect the resource.

Jan 1, 1999

By Raymond W. Henn

The 30th annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, June 22-26, 2009. The field demonstration portion of the course was conducted June 25, at Hayward Baker, Inc.?s yard in Broomfield, CO. The full-scale field demonstration annually presents many different types of drilling equipment being operated as well as various grouting methods being performed under different field conditions. As part of the field demonstration, the class is shown the proportioning, mixing, testing and injection of various cement grout mixes into sand columns under controlled and measured conditions. These sand column demonstrations have been conducted under controlled and measured conditions each year since 1999 as part of the short course. The sand column demonstrations were conducted prior to 1999, but with less quality control and minimal record keeping of the proportioning, mixing, testing, injection pressures and the final permeation results. The goal of the sand column demonstration is to show the students the effect of the water cement ratio and the use of admixture as well as the fineness of the cement, portland versus ultrafine, used has on the engineering properties of the grout and the grout?s vertical permeation through the sand. Test results for the demonstrations conducted in 1999 and for two separate demonstrations, one at the grout course and one at Geo Denver, conducted in 2000 were published in the 2001 proceedings of the Rapid Excavation and Tunneling Conference (RETC) (Henn et al. 2001). The test results for the 2002 and the 2003 demonstrations were published in the 2005 proceeding of the RETC (Henn et al. 2005).

Jan 1, 2009

Orebodies are defined in economic terms in that they must satisfy conditions determined by costs of mining, extraction and marketing before being so described. Despite this they have an essential chemical character as specialized products resulting from geochemical differentiation, and it is surprising that so little basic geochemical research has been carried out with respect to ore occurrence and that prospecting methods based on geochemical principles are not more widely applied.Many exploration geologists associate geochemistry with analytical techniques applied to the detection of dispersed traces of metals from actual orebodies. Geochemical research, applied to economic geology, goes far beyond this limited field and the purpose of this paper is to discuss aspects of such research and its use in formulating exploration principles.THE GEOCHEMICAL BACKGROUND TO MINERAL OCCURRENCE AND EXPLORATIONThe three aspects of economic mineral deposits to which geochemical research can be of use in determining ore guides are genesis, control of deposition and mode of dispersion from orebodies after emplacement. Prospecting for mineral deposits is primarily based on theories of ore occurrence which deal with the genetic and depositional influences controlling localization of ore. There are many such theories and they will not be discussed here as they have been adequately reviewed in geological publications. Some are based on differing argument concerning the same empirically observed associations of ore. In this respect it is perhaps fortunate that they are not always mutually exclusive as regards the...

Jan 1, 1960

By A. Beitz, P. Smartt, G. Einicke, G. Rowan, P. Glynn

Coal is Australia’s highest export earner and Australia is the world’s largest exporter of coal. With coal now being extracted from deeper reserves under increased risk profile, and in the interest of aiding the stability of coal supplies, Japan is funding a number of safety projects in Australia and China. The CSIRO, Australia’s premiere research organisation with the country’s largest exploration and mining research group, are currently undertaking a jointly funded Japan-Australia safety project at Anglo Coal’s new Grasstree Colliery in central Queensland. The project, entitled Mine Communication and Information for Real-time Risk Analysis, will deliver step-change capabilities in data integration, decision support, gas monitoring, geo-technical monitoring, emergency response and personnel safety to the Grasstree Colliery. Some key activities include: developing and installing underground coal mine Ethernet LAN components, real-time monitoring of gas and geo-technical sensors, MODBUS serial to TCP/IP converters, e-reporting of underground conditions, emergency guidance systems and underground trials of Internet Protocol telephone and video. The project seeks to integrate (in real time) key data sets from the comprehensive and diversified range of propriety system currently in use at mines (ventilation, strata, operations e.g. haulage, pumps, conveyors etc) into a single integrated risk management interface. This interface will filter the data through a rules-based inference engine that will cross reference the various data streams, compare with past events and outcomes associated with the similar historical data and present this “intelligence” to

Jan 1, 2003

By Thomas L. Richardson, David R. Chapman, Gary W. Gilbert

The two contracts of the Big Walnut Augmentation/Rickenbacker Interceptor(BWARI) sewer project for the City of Columbus, Ohio total nearly 35,000 feet of 14and 12-foot diameter tunnel. EPB TBMs will install precast concrete segmental lining through difficult glacial soils ranging from clean granular to hard till with high groundwater and boulders, crossing roads, railroads, and a large stream. Construction of 12 shafts and a large Interconnect Structure involving major ground stabilization work is required. The paper will review design of major project elements and present an update on construction progress.

Jan 1, 2005

By P Lever, D Hainsworth, H Gurgenci

The ACARP Landmark initiative has created the opportunity to advance the level of automation in the coal industry by first focusing on the core production area of longwall mining. A Landmark Longwall Automation project was commenced in July 2001. The major outcome of automation using on-face observation has been divided into ten outcome areas that have been fully scoped for a three-year initial project life. A major facilitating technology has been the implementation inertial navigation system (INS) technology that can map the shearer position in 3D. A focus of the project is to deliver a system that is at least as productive as the current most productive manually controlled longwall face.

Jan 1, 2002