Search Documents

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

By John G. Peacey, Leoncio Sevilla G., Ford. Kevan J. R., Erling Villalobos C.

"Kinross Gold Corporation’s Mantos de Oro (MDO) gold/silver mine in northern Chile currently processes 15,000 tpd of oxide ores through a mill, whole ore cyanide leach plant followed by a Merrill-Crowe refinery. With the expected depletion of these oxide ores in a few years a new sulphide mineral deposit, Ladera-Farellón has been identified to potentially replace existing ore reserves. The deposit contains approximately 0.5g/t Au, 6g/t Ag and 0.5% Cu. The principal sulphide mineral in the deposit is enargite (Cu3AsS4) which hosts the majority of gold and silver and the copper. Direct cyanidation testwork has shown the sulphide mineral is refractory with a low gold recovery of 36% and silver recovery of 45%. Oxidation of the sulphides is required to liberate gold and silver and allow recovery of copper as an important pay-metal. Therefore, at MDO a new metallurgical process route with oxidation as a pretreatment step is required for viable treatment of such new sulphide mineralized material with acceptable recoveries of pay-metals.Analysis of flowsheet options was completed based on bench-scale and pilot scale metallurgical testwork as well as with reference to existing studies and operations. The process options investigated assume concentration of sulphides by flotation, followed by either pressure oxidation, bacteriological oxidation or roasting. Preliminary evaluation of flowsheet options focused on process risk, operability, technology availability and the economics of the project with emphasis on use of the existing metallurgical plant to reduce capital cost. Operating costs for each process option were also included in the relative analysis.The challenges of treatment of MDO sulphides, principally enargite and pyrite for recovery of gold, silver and copper center on fixation of arsenic and sulphur capture with environmentally acceptable disposal of residue tailings. This environmental focus was included in the process option selection and comparative analysis.This paper presents a review of the process options considered and highlights comparative advantages/disadvantages of each process with associated environmental issues. Preliminary conclusions are drawn on roasting as a potentially favorable process option for the treatment of MDO sulphides."

Jan 1, 2009

By Takefumi Takuma, Masashi Nagano, Christopher DellAringa

Multiple agencies in Southern California are retrofitting and upgrading their levees to catch up with ever-advancing urbanization affecting the requirements for existing channels and levees in this seismically active zone. Pressed-in sheet piles have been specified on some of these projects to minimize noise and vibration problems associated with sheet pile installation. This paper will study three Southern California levee and sewer pipeline retrofit projects that utilized pressed-in sheet piles in hard soil conditions with N-values higher than 50. BACKGROUND Southern California is home to numerous drainage channels fortified with earthen levees. In spite of the region’s semi-arid climate with varying annual precipitation from year to year, winter storms can bring in heavy and continuous rainfall to the area which overwhelms the levees’ capacities at times. Some levees are running through densely populated areas with homes and other sensitive structures such as underground utilities and bridge piers. Conventional sheet pile driving utilizes either percussive or vibratory pile driving methods, both of which generate high levels of noise and vibration, causing nuisance and potential damage to nearby structures. On the other hand, the press-in piling method utilizes a hydraulic force to push piles into the ground, thus practically eliminating the noise and vibration issue. Although there are types of press-in piling systems mounted on tall leaders on large crawler-base machines, they are less frequently used due to its much larger size and more limited drivability than the type discussed hereunder. The other type of press-in machine sits on top of already installed piles and is anchored with its own weight and additional counter weight when starting off as shown in Figure 1. Once the first few piles are pressed in, the equipment grips on top of the installed piles and moves forward on its own as the pile installation progresses. See Figure 2. This method does not use a vibratory or percussive force to install piles.

Jan 1, 2018

By V. N. Cox, C. H. Grant

Both the underwater method and the rock cratering method contribute useful information in evaluating and comparing new explosive compositions. Results indicate that metallized explosive systems which contain no high explosives can be formulated to offer more energy and to do potentially more work than other slurry explosive systems. Commercial field trials are presently being conducted with a metallized explosive that does not contain any high explosive. Although there have been only a few commercial blasts to date, the results are encouraging. The Dow Chemical Co. has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which DOW is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of nonmetallized explosives currently being used. Early in 1960, additional patent rights were acquired from independent inventors and a development station at Virginia, Minn., was set up to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the boreholes. Due to the complexities involved in controlling the manufacture of the explosive in the borehole, performance was sometimes in doubt. Furthermore, experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over 2000 charges of 8 to 60 lb under water and in taconites and granites with many types of explosives, a metallized explosive was developed which is now being manufactured at a pilot plant in Virginia, Minn. and is being evaluated commercially. UNDERWATER METHOD An underwater method of evaluating explosives has a number of advantages. A permanent site can be established and operated indefinitely. A large number of charges may be fired in a short length of time. The medium in which the explosive is shot is exactly the same for successive shots. Data are recorded electronically minimizing human judgment. A disadvantage of the underwater method is the lack of confinement provided by the water medium. Many explosive compositions require a greater degree of confinement to develop good energy release. Although the relative significance of the two components of energy release that are usually measured, the shock energy and the bubble energy, and their relationship to breaking rock are not clearly understood, the underwater method is a valuable research tool for screening explosive compositions and gaining an insight into the manner in which explosives release their energy. Fig. 1 shows schematically the underwater apparatus. The piezoelectric gages are calibrated tourmaline crystals which convert the shock wave to an electrical impulse which is transmitted to an oscilloscope and recorded on Polaroid film. The shock traces are picked up by scopes 1 and 2. Scope 1 is timed to pick up the full trace whereas scope 2 is timed to cover the first increment of the shock trace expanded, and therefore allows full inspection of the propagation and peak pressures. Scope 3 records the bubble trace. When the explosion occurs, a bubble of gaseous detonation products is formed. The outward momentum of the water keeps expanding the bubble even after

Jan 1, 1963

By E. F. Schnitzer, S. R. Mamoyac, P. J. Wampler

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries – Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

Industrial minerals enjoyed a fairly successful year in 1978, despite the sluggish economy, inflation, and environmental restrictions. A glance at US Bureau of Mines statistics shows that, in general, production of industrial minerals increased from + 1% (salt) to as much as 26% (sulfur, other than Frasch or recovered). A few industrial minerals showed a decline; fluorspar production, for example, registered a 23% decrease in 1978 from 1977 due to the closing of three domestic mines. Bromine, natural sodium sulfate, Frasch sulfur, and vermiculite also had production decreases of 2-6% in 1978.

Jan 5, 1979

By T. R. Curr, R. T. Jones

Keywords: Pyrometallurgy, Mintek, DC arc furnace, plasma, smelting, chromite, ilmenite, cobalt, slag, zinc fuming, dust, magnesium, laterite, ferronickel, arc modelling, Pyrosim, thermodynamics The Pyrometallurgy discipline at Mintek was initiated in the early 1970s, to support a growing ferroalloy industry in South Africa. In addition to a range of pyrometallurgical options, Mintek specialises in DC arc furnace technology and has pilot plant facilities up to 5.6 MVA, as well as a strong base in process and arc modelling. Industrial processes have been developed for ferrochromium production, ilmenite smelting, and cobalt recovery from slag. Recent work has been done on such processes as the production of ferronickel from laterite ores, the fuming and condensation of magnesium, and the recovery of platinum group metals from 'difficult' feedstocks.

Jan 1, 2006

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By J. P. Welsh

Ground Modification construction is rapidly evolving in the United States. An assessment of the construction status of Ground Modification methods with their dates of introduction and general acceptance in the United States is summarized. Seven of these techniques are discussed in depth with short case histories; namely, Dynamic Deep Compaction, vibro-compaction, vibro-Replacement, chemical grouting, compaction grouting, slurry grouting and jet grouting. Additional case histories are presented to illustrate the trend of combining Ground Modification techniques to solve specific site problems.

Jan 1, 2010

A series of in situ pull tests has been conducted to determine the holding capacity of the standard SS46 Split Set Stabilisers. The experiments have been conducted in a wide range of geological conditions ranging from bedded rock to blocky ground. The results presented in this paper indicate that cement grouted split sets bolts are likely to provide up to three times the initial bond strength per metre of embedment length provided by the ungrouted bolts. The increased load transfer capacity of the grouted bolts provides an alternative for permanent excavation support using split set stabilisers.

Jan 1, 1997

The Acid Leaching Process for the Synthesis of Zeolitic Material from Paper Sludge Ash

Sep 13, 2010

Geological Parameters Controlling the Improvement of Manufactured Sand Using Vertical Shaft Impact Crushers Instead of Cone Crushers Natural sand is a limited resource. In Sweden the total use of natural sand and gravel is around 20 million tonnes per year and the goal is to halve the use of this resource in the near future. Most of this natural sand is used for concrete production, so the consequence of this goal is that more and more concrete must be produced with manufactured sand. The bedrock of Sweden consists mainly of granites and gneisses, rock types mainly composed of various amounts of quartz, feldspar and mica. Manufactured sand from these materials generally contains rather flaky and elongated grains, and there are few types of granite that can be used as manufactured sand in concrete without increasing the amount of cement by eight to ten per cent. A Vertical Shaft Impact crusher (VSI) is commonly used to improve the shape of coarse aggregate particles. Research has shown that it is even possible to improve the shape in aggregate fractions less than 1 mm for some rock types. The aim of this project was to investigate which geological parameters control the improvement of manufactured sand when using VSI-crushers instead of the traditionally used cone crusher. In order to do this eight rock types of granitic composition were investigated. The selection of rock materials for the tests was based on grain size and mica content. A 4 - 8 mm fraction of each material was used for the tests. The characterisation of the shape of the material was performed using image analysis applied on microscopic images. The results showed that the VSI-crusher had improved the shape of all materials down to 0.036 mm, except for one rock sample. According to these results granites with low mica content and relatively high content of feldspars have the best prerequisites to produce manufactured sand for concrete with suitable geometric characteristics, and if these materials are crushed with a VSI crusher they almost show the same characteristics as natural sand.

Sep 13, 2010

By C. Scheffer

This paper describes a model that can simulate the behaviour of a pneumatic intensifier that is generally referred to as an ?air pump? (AP). The AP is used in many South African underground mines, and utilizes compressed air with pressures between 0.3?0.6 MPa to pump water up to pressures of 12?18 MPa. The high pressure water is used in numerous underground mines to pressurize props and roof bolts that act as safety and roof support devices. The simulation model reproduces the intensifier's operation under various conditions and therefore can be used to investigate the AP's sensitivity towards environmental conditions, design parameters (such as spring stiffness, plunger diameter, nozzle diameter etc.) and operating conditions. Model validation by comparison with laboratory experiments showed good correlation. The model can subsequently be used to investigate design changes aimed at improving the AP's performance and reliability over a wider range of operating conditions.

Jan 1, 2005

By Y. El-Mossallamy

The piled raft foundation was extensive applied in the last two decades in different soil conditions e.g. in soft to stiff clay as well as in medium to dense sand and even in highly weathered rock. The piled raft is now applied not only to control the foundation settlement but also to minimize the required raft thickness to reach the most economic foundation design. An innovative application of the piled raft is its special adjustment to cases of foundations with large load eccentricities or very different loaded parts of buildings to avoid the need of settlement joints, which are especially complex below ground water table. Recently, the piled raft is applied for foundations of highway and railway bridges with special serviceability requirements regarding the allowable total and differential settlement as well as tilting. Actually numerical analyses are the mostly used design methods for piled rafts. For all day design practice a simple and modest design method is highly needed -at least in the first design stage- to check the feasibility of the piled raft on the specific project conditions. In this paper, a general overview on the recent innovative applications of piled rafts in Germany will be presented in a short overview. The results of the simple design method will be discussed and compared with the results of more enhanced numerical methods.

Jan 1, 2006

By C. A. Olivier

Le Ministère des Richesses naturelles du Québec has continued development work on the process/or direct reaction 0/sodium carbonate with lithium-bearing silicates(Canadian Patent No. 643,843). Recent process improvements have involved continuous pressure leaching, rather than batch leaching, and higher solution concentrations (over 55 g/l Li2CO3. These improvements have been demonstrated on a pilot scale operating on decrepitated spodumene from the Sullivan Mining Group's Quebec deposit. The new process is expected to be very competitive with the conventional sulphuric acid route. The improved flowsheet and main process steps will be described along with pilot-plant results.

Jan 1, 1979

By G. Huang, S. Vytla

Computational fluid dynamics (CFD) is a continually developing numerical technique by which complex fluid flow problems can be solved on computers. To be able to transfer CFD expertise to analyze and design a face-ventilation system, a comprehensive validation study of current CFD tools against mining-related benchmark experiments is required. In the last four years, such studies, funded by National In¬stitute for Occupational Safety and Health (NIOSH) under Grant #R01 CCR415822, were conducted in the Department of Mining Engineering at the University of Kentucky. A wide array of ventilation schemes and mining configurations were considered. Recently, an additional study was performed in cooperation with the NIOSH Pittsburgh Research Laboratory. This study was dedicated to the methane behavior in the empty (containing no equipment) face area with a blowing curtain and a 10. 7-m (35-ft) setback. In this paper, the authors present and discuss the computer-simulation data and compare them with data collected during the laboratory studies at the NIOSH lab.

By P D. Katsabanis

According to Persson(1) steady state detonation along a cylindrical charge can be regarded as a self propagating process in which the axial compressive effect of the shock front discontinuity changes the state of the explosive so that exothermic reaction sets in with the requisite velocity.

Jan 1, 1990

By Michael L. Boucher

Copper and nickel sulfides occurring in the Duluth Complex of northern Minnesota were examined at the Bureau of Mines, A microscopic study was undertaken to determine the mineralogy and paragenesis of the ore minerals. Eighty-two samples were taken from one deep diamond drill core located near Babbitt, Minn. Modal analyses are presented for the Duluth Complex rocks and for the are minerals in the major mineralized zone. The major sulfide minerals are chalcopyrite, cubanite, pyrrhotite, troilite, and pentlandite. Results of this investigation suggest that the mineralization is related to the structural features of the enclosing rocks: pores, open fractures, and cavities. The pyrrhotite-troilite-pentlandite assemblage is believed to have formed from an immiscible sulfide melt, probably associated with the troctolitic rocks. Most of it settled to the very porous base of the Duluth Complex, and to the other porous zones near xenoliths; small portions were trapped higher in the section. A later introduction of a copper-rich sulfide melt replaced some of the pyrrhotite-troilite and oxides, and filled in the remaining open spaces and fractures in the Duluth Complex and those of the adjacent footwall rock.

Jan 1, 1975

By P. Hickey, J. Spenceley, T. J. DeMull

Development of the Batu Hijau Project was successfully completed in the fourth quarter of 1999 with the final handover and start-up of ore processing facilities. The development project had started more than three years earlier, in August 1996, when the Owner, PT. Newmont Nusa Tenggara (PTNNT), awarded an EPC contract to Fluor Daniel (FD) for design and construction of the project including: copper concentrator, port, power plant, town site, and infrastructure. PTNNT managed the development of the mine and procurement of mine equipment with its own forces. Bringing the Batu Hijau copper deposit into production was the largest mining project ever undertaken. Development of Batu Hijau was a complex project involving the work of tens of thousands of people in all parts of the world to complete engineering, manufacture and deliver equipment, supply materials, and build the plant. The ore deposit is located on the tropical island of Sumbawa in a remote and undeveloped section of Indonesia. The location and environment presented challenges for all phases and aspects of the project. To meet the challenges, the project team combined good planning and teamwork to best utilize the resources available. This approach assured continuity of personnel through construction to operations and minimized cost, resulting in completion of the project ahead of schedule and under budget.

Jan 1, 2001

By George J. Karcas, Raimo Kuusisto, Pertti Pekkala

Ongoing Outokumpu development in Solvent Extraction and Electrowinning Technology, involving all aspects of process chemistry, equipment and control, extends over a period of close to 30 years. The development in SX started with molybdenum and rhenium, continued with zinc, manganese, cobalt and nickel and is now focusing on copper. The OutoCompact VSF? SX concept, which has been recently introduced, is a honed version of earlier VSF? technology. The Outokumpu VSF? ("Vertical Smooth Flow") SX package includes the DOP ("Dispersion Overflow Pump") units, the Spirok Mixers, the OutoCompact Settlers including their DDG ("Dispersion Depletor Gate") fences and tank farm equipment such as the LOS ("Loaded Organic Scrubbing") tank as well as the CEP ("Copper Electrolyte Purifying") tank. Although the VSF? SX package can be implemented according to several optional lay-outs, the so-called Track version has lately been introduced to the advantage of new plants. The new OutoCompact SX technology decreases the footprint of future VSF? plants. The lay-out, including plant size flexibility, have further been improved by Outokumpu?s new OutoReverse settler technology. Two of several SX plants currently under construction rely on reverse settlers in order to maximize their performance. The Outokumpu EW technology includes process know-how as well as proprietary equipment. The copper EW package consists of permanent stainless steel cathodes based on wax-less technology and lead anodes utilising polymer concrete cells with the double contact bus bar system and ventilation hoods fitted for efficient mist control. The lifting of cell hoods, as well as cathode washing, is done by the cathode pulling crane. Proper electrolyte flows and matching current density further ensure high productivity of LME grade copper cathodes.

Jan 1, 2005