Search Documents

By Shirleny Fontes Santos

Muscovite mica crystals lower than 15 mm diameter are discarded as waste in the mining area of Borborema-Seridó (BRAZIL). The objective of this work was the ore dressing and purification of this waste to be used in the preparation of pearlescent pigment. Muscovite was dry ground using knife mills and an ultrasound treatment. It was possible to achieve 67% of mica with particle size lower than 100 µm. This product was used in the preparation of brilliant pigments based on muscovite flakes covered with rare earth oxides (CeO2, PrO2, Ce0,95Pr0,05O2). The pigments were characterized by X-ray diffraction, thermal analysis and scanning electronic microscopy. The color of the resulting pigments was analyzed using the CIELAB method and it showed the following colors: muscovite-CeO2 ? yellow, muscovite-PrO2? black and muscovite-Ce0,95Pr0,05O2 ? orange. Those results have shown that ?trash mica? is suitable for use in pigment preparation.

Jan 1, 2010

By A. K. Singh

Between the main fan and the coalface in a mine a lot of air is lost through leakage at stoppings, doors, air-crossing etc. so that a much larger quantity of air has to be circulated by the fan in order that the stipulated quantity of air reaches the face. Stoppings are of vital importance not only for effective ventilation of underground mines but also for isolation of areas affected by fire or susceptible to spontaneous heating. Generally, isolation stoppings are made of brick in cement mortar. If the area is far from the pit or unapproachable, it is very difficult and sometimes impossible to build these stoppings. To overcome these difficulties, particularly near fire affected zones, an alternate successful attempt was made in Indian mines to make a plug underground, from surface through borehole, using cement concrete. In this paper the salient features of the methodology adopted for construction of the plug and the experimental procedure for the measurement of air leakage by SF6 tracer gas is described. Measurements of air leakage through rows of ventilation stoppings in two mines viz. Moira (Jambad and Kajora seams) and Kuardi11/12 (Niga seam) collieries of Eastern Coalfields Ltd. (ECL) have been incorporated. Results of experiments conducted at the Central Mining Research Institute (C.M.R.I) to determine leakage through25 and 38 cm thick brick stoppings are also discussed. Results of all these studies are compared, which show that the efficacy and reliability of the remote filled cement concrete plug in respect of air permeability is satisfactory.

Jan 1, 2004

By Mark A. Williams

Topography and geology greatly impact the decision of how to plan and operate a surface mine. To extract coal, five primary surface mrning methods are practiced in the United States. These include contour strip. mountamtop removal, area, modified area, and open pit mining methods. The first four approaches are commonly associated with coal mining while open pit techniques, although used in the mining of coal, are more commonly applied to the mining of hard rock, metals, and aggregates. Various sub-routines of the primary surface mining methods are likewrse applied rn the industry.

Jan 1, 1991

By King E. J

Department of Pathology, British Post-graduate Medical School, London:The experiments here recorded were devised and carried -out during the last two years in an attempt to corroborate the important work of Denny, Robson and Irwin (1939) in which they found that experimental silicosis could be prevented by means of metallic aluminum. By causing rabbits to inhale powdered quartz for several months they induced experimental silicosis. These animals then served as controls for comparison with another group which were dusted with a mixture of quartz and aluminum. In the second group silicosis failed to develop.Our experimental procedure was somewhat different. We resorted to intratracheal insufflation instead of simple inhalation, and we used rats instead of rabbits: otherwise the essential features of the original experiments were carefully duplicated.EXPERIMENTAL PROCEDURES.A single dose of dust was delivered into the lungs of each animal. The dust was suspended in a fluid medium and injected by means of a syringe directly into the trachea in known quantity (technique of Kettle and Hilton, 1932). The suspensions were autoclaved before use and were injected with aseptic precautions. Having had a long experience of this technique we employed it with confidence and usually secured a fairly uniform dispersal of dust throughout both lungs. To carry out injections successfully one requires, above all, an even suspension of dust which will flow smoothly and quickly from the syringe. This is not difficult in the case of quartz, for, though it tends to settle out rather quickly, this can be avoided by constantly agitating the suspension. The syringe containing the inoculum may be shaken gently right up to the moment of injection and then emptied quickly to prevent sedimentation. Powdered aluminum is more difficult to handle, for the particles tend to flocculate and are not readily made to disperse evenly in saline, even by violent shaking. For this reason an emulsifying agent may be used to advantage, provided it does not complicate the experiment, a point to be mentioned again presently.THE EXPERIMENTSExperiments with quartz alone: Extensive silicotic lesions were produced in 23 out of 26 rats by the administration of pure quartz dust in doses of from 50 to 200 mg. per rat. The dust was so finely pulverised that the particles averaged about 1-p. in size: none was larger than 5 p. and 99 per cent. were under 2.5 p.Eight of these animals survived for seven months and were then killed...

Jan 1, 1945

By V. Bari?ic

The scheduled power cuts of early 2008 were a disturbing reminder that South Africa needs to expand its power-generating capacity. Low-grade and discard coals, of which South Africa has much, are a source of energy and amenable to combustion in circulating fluidized beds (CFBs). Foster Wheeler (FW) has a long record in developing this technology in boilers. The technology is flexible in burning a variety of fuels; low-grade, high-ash coals, good quality bituminous and anthracite coals, and biomass and waste fuels have all been used. CFB boilers are efficient, reliable and can be designed to meet tight emission standards. In recent years once-through supercritical (OTSC) CFB technology has been developed. It enables the next stage in CFB development to proceed to a medium-scale (500 MWe) utility in such projects as Lagisza, which runs at a net efficiency of nearly 44%. Scaling the technology up to 800 MWe with a net efficiency of>45% is planned to be commercial during 2009. CFB technology can reduce CO2 emissions in the repowering of coal-fired and greenfield power plants. It does so through greater efficiencies and by co-combusting coal with biomass. FW has also developed CFB technology for the gasification of biomass, as, for example, in a pressurized gasifier to produce syngas, which can be used for the production of biodiesel, thereby reducing CO2 emissions from vehicles. Carbon capture and storage (CCS) can potentially cut CO2 emissions in the generation of power from fossil fuels in the short term, provided that it gains public acceptance, that the required regulatory framework is created, and that emission-trading mechanisms or other incentives provide a solid return on the major investments required. Oxyfuel combustion is an option in CCS; Foster Wheeler is adapting its CFB combustion technology for oxy-fuel combustion to meet this challenge. It is developing Flexi-burn?, which enables a plant to be operated either with or without carbon capture. This paper describes the status of CFB technology in terms of boiler efficiency and fuel flexibility. It highlights the advantages of CFB technology for oxyfuel combustion, presents a development plan for Flexi-burn?, and discusses a pressurized gasifier for biodiesel applications.

Jan 1, 2009

By Pr-Anders Persson

This chapter deals with the concepts of shock waves and detonation waves together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the c.ootext of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of sn explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of this chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1995

By J. R. G. Williamson

The Mining Division of Iscor, an integrated minerals and metals company, has recently completed a feasibility study for the establishment of a new heavy minerals mine and smelter in the Richards Bay area of KwaZulu-Natal, South Africa. The mine will produce a heavy mineral concentrate containing ilmenite, zircon, rutile and leucoxene which will be beneficiated at a central processing complex close to Empangeni. The ilmenite will be smelted to produce high-grade titania slag and pig iron for export. The ancient dune containing the mineral deposit is located some distance inland of the coastal dunes, and the sands contain a high proportion of extremely fine material which must be extracted ahead of the gravity separation process. Of the 56 million tonnes to be mined annually over the ten-year life of the mine approximately 23,4%?a total of 13,1 million tonnes of minus 45 micron residue fines?will have to be disposed of in a containment facility. The origin of the fine material is from the weathering of amphibole minerals. The remaining coarse sands will be returned to the mined area to re-create the original dune configuration. A number of options for the disposal of the residue fines have been examined and specialised laboratory tests undertaken to determine the deposition behaviour of the fines. The final solution involved the use of a ?sub-aerial? technique for deposition of fine material in a disposal facility. The resulting arrangement will adequately meet technical and environmental criteria. Upon closure after 10 years of operation, the surface of the disposal facility will be returned to sugar cane cultivation The paper refers to the various options considered and describes the problems associated with competent disposal of the residue fines and the development details of the final disposal facility.

Jan 1, 1997

By Patrick E. Durnal

A joint venture of Ben C. Gerwick Inc., Sverdrup (now Jacobs) and DMJM (now DMJM Harris) designed the $779 mill seismic upgrade of the Richmond - San Rafael Bridge over the San Pablo Bay in the San Francisco Bay Area and provided construction support to Caltrans. Construction of the marine foundation retrofit was completed by a joint venture of Tudor Saliba/Tidewater/Koch-Skanska and their subcontractors: Pomeroy Precast Construction, AGRA Foundations, Dutra Construction and Vortex Divers. Construction management and inspection was performed by Caltrans with support of various consultants.

Jan 1, 2013

By J. N. Van der Merwe

The data base of failed pillar cases as used by Salamon and Munro (1967) in their original analysis to determine the strength of coal pillars empirically, has been updated for this study. It is shown that the Vaal Basin and Klip River coal fields exhibit similar behaviour that differs from the failures in other areas, i.e. failure at high safety factors within a short period of time. Those collapse cases have been omitted from the new data base. Failures in the other areas that occurred after 1967 have been added. Using a technique to minimize the area of overlap between the populations of safety factors of failed and intact pillar cases, the new data base was re-analysed in conjunction with the original Salamon-Munro data base of intact pillar cases, from which the cases in the areas of weak coal were likewise eliminated. It was found that a linear formula reduced the overlap area by22%. The new formula predicts higher strength for pillars with a width-to-height ratio greater than approximately 2.0 to 3.0 and a lower strength for smaller pillars. It was also found that in order to obtain the same relative measure of stability as with the Salamon-Munro formula, the strength constant in the new formula should be within a range of 2.8 to 3.5 MPa. For most current South African coal mining conditions, using the new formula for pillar strength will result in leaving smaller pillars without sacrificing stability. The reason for this is that the Salamon-Munro formula under-estimated the strength of larger pillars and over-estimated the strength of smaller pillars. The new formula will thus result in improved reserve utilization without sacrificing stability.

Jan 1, 2003

By Tapiwanashe Chenje, David Hewitt, Peter Radziszewski

"Steel media wear is a major cost component in mineral processing. In the case of existing operating mill, steel media wear prediction can be used to help compare the performance of steel media from different suppliers before completing marked ball tests. It can also be used to investigate how ores from different site of a given mine affect steel media wear. In the case of Greenfield cases, steel media wear prediction can be used to estimate the cost of steel media for a given feasibility study.This paper presents a wear testing and prediction methodology that ties together abrasion wear and corrosion wear testing results through the use of a simplified discrete element charge motion model. The experimentation dimension to this methodology takes samples for steel media, mine site ore and water to determine abrasive and corrosive wear parameters of a given media, ore, water set.The test methodology development is illustrated along with a comparison of wear predictions with observed wear rates in some operating mills. A case study is included that illustrates how this methodology was used to estimate steel media wear performance. The paper closes with a discussion on the use of parts of the experimental methodology to investigate other abrasive wear conditions such as liner wear, paste backfill piping and ore breakage as well as avenues for future test development.INTRODUCTIONThe cost of comminution processes represents a significant part of the overall costs of a mining operation. Grinding media/liner wear alone accounts for 15-25% of the total operating cost. The annual steel grinding media consumption is approximately 2.5 mtpa or 0.3% of total world steel production [Smorgon Steel Group, 2005]. Using an estimated grinding media cost of about US$0.75/kg [Halbe and Smolik, 2002], gives a media cost of over US$1.875 billion per annum. Mining continues to shift towards exploitation of lower grade ores as the higher grades get depleted. These low-grade ores require finer grinding for the liberation of the value minerals, and hence it can be assumed that grinding media consumption will also continue to rise.The Bond abrasion test, dating back to 1963, [Weiss, 1985] is still used to estimate the total mill media wear. This is a purely empirical test based on the ore. From Bond abrasion index tests, it is possible to determine a wear rate using the following function:"

Jan 1, 2009

By Steven A. Mathe, Seokbin Lim

Current analytical models can accurately predict the final velocity of explosively driven flyers and can somewhat predict the acceleration profile, but do little to address the deformation of the flyers. Explosive systems such as linear shaped charges and explosively formed projectiles, which can be described as multiple interacting explosively driven flyers, often involve interactions between the flyers that occur much before the flyers reach their predicted final velocity. In this regime, it is important to accurately understand both the acceleration profile and the deformation profile of the flyers, as both significantly affect the functioning of the explosive systems. Previous work proposed an analytical model to meet this need. As the expanding gas cloud of detonation products drives the flyers, rarefactions impinge upon the gas cloud from around the flyer edges, which produces a pressure difference across the back face of the flyer leading to deformation of the flyer. Previous research condensed the effects of the rarefactions into a single term, the pressure release ratio, ?, which was calculated based on hydrocode simulations of a block of explosive only and an assumption of isentropic expansion. This work intends to determine the value of ? for different explosive compounds. The results of this analysis were compared to hydrocode simulations of an open-faced sandwich configuration explosive/flyer system with an average accuracy of 15% across the tested compounds.

Jan 1, 2015

By Dwight L. Sawyer

To provide technology that can help decrease the dependence of the U.S. aluminum industry on imported bauxite, the main ore of aluminum, the Bureau of Mines is investigating the extraction of aluminum from abundant domestic reserves of kaolinitic clay. Miniplant studies of the continuous leaching of calcined kaolin with boiling 25-pct HC1 acid resulted in a 93- to 99-pct extraction of the acid-soluble alumina in the calcined kaolin feed. Data are presented for an acid leaching study carried out in three or four continuously stirred tank reactors (CSTR) in series, feed rates of 100 to 250 lb/hr of calcined kaolin, and total nominal residence times of 0.7 to 2.3 hr. A material balance for a 176-lb/hr calcined kaolin feed rate in a circuit consisting of three reactors, four classifiers, and five thickeners is given. Data provide detailed compositional and physical information for calcined kaolin, process liquors, and acid-leached residue solids.

Jan 1, 1983

By Brijes Mishra

This paper presents a correlation of acoustic emission (A.E.) with physical and mechanical properties of different types of rock and coal specimens which were tested under aegis of a consultancy project from a Columbian Mining Company. In this study, three types of rocks which are sandstone (Arneisca), siltstone (Arciolita) and claystone (Limolita) and two different types of coal were tested. The tests were carried out under constant loading rates according to ASTM Standards for determining Young?s Modulus and Poisson?s Ratio. In both cases a MTS electro-hydraulic loading system was used. Mode of failure in each material was characterized by the acoustic emission and the results were substantiated by the deformation characteristics of the materials during failure.

Jan 1, 2006

By Deshmukh A. M.

Existence of human beings and their relationship with the nature is symbiotic. The lack of perspective and negligence of nature disturbs the equilibrium of environment and causes unprecedented disasters. Geotechnical engineers are directly concerned with hazards of nature as elements of foundation and of nature are inter related. Rational design and construction of foundation can be accomplished only after properly assessing influence of environment This paper briefly delineates impacts of environment and human activities and presents salient features of management of impacts through the system of deep foundation. Limitation of negative effects and enhancement of positive developments necessitates eco-consistent planning of engineering projects based on the geotechnical aspects of environmental impact management.

Jan 1, 1996

By Robert K. Jonas

"Minerals processors can improve production by using the best available control technology to control their operations. Many mines use expert systems that can provide improved results over manual or basic control, but better results can be achieved using multivariable predictive control. Over the past few years, the application of multivariable predictive control has gained acceptance in many mining processes and has recently proven to be suitable for some of the most challenging processes. This advanced control technology has been successfully applied to a wide variety of processes; alumina digestion, ball mills, CCD/thickeners, kilns/calciners/roasters, heat exchangers/evaporators, and more demanding processes like SAG mills and flash smelters.This paper discusses the needs of advance control technologies in the mining industry, including the impact of these technologies on best practices for implementation and long term sustainability. Results of the multivariable predictive control applications in mineral processing are discussed, and in particular the application to the SAG mill. In addition, an example of the benefits improvement that can be achieved with this technology is presented.INTRODUCTIONThere has been a long term perception in the mainstream mineral processing industry that best advanced control solution is an expert system. There a numerous instances of expert systems used for control of SAG mills, as well as kilns or roasters, thickeners and more recently flotation circuits. Many of theses expert systems have been installed by small, independent companies or by OEMs of processing equipment. Undoubtedly these expert systems have provided millions in benefits to the owners of mineral processing plants.It is this author’s proposition that it is a misconception to believe that expert systems are the best solution for mineral processors, and that in many cases the best solution is Multivariable Predictive Control (MPC). Better control and optimal operations can be achieved through the use of MPC. Another important consideration when considering advanced control technologies is the implementation and support effort. These types of applications have been known to deteriorate, even to disuse, when they are not kept up to date with changes to the process or equipment. The audience is invited to listen to discussion and draw their own opinion. The author has been involved in installing control systems for over 20 years, advanced solutions for over 15 years, and has had privilege to consult with many miners concerning the selection and application of advanced controls over the past 6 years."

Jan 1, 2008

Safety is the No. 1 concern of any drill contractor or mine operator. Everyone in the industry knows a safe site helps stabilize operational costs and enables higher productivity. When it comes to exploration drilling, research has proven a majority of injuries are caused by the mishandling of coring rods. A driller helper will typically handle up to 50 rods per shift or up to 15,000 rods per year. With an annual 340 t (750,000 lb) in rods managed by hand, the risk of serious injury is extremely high. Because of this, the top request from the exploration industry is diamond rod handling. The Boart Longyear 4200 surface exploration drill, slated for release in 2009, will give the industry a hand-free, operationally safe rig.. Developed through the collaboration of its global drilling services and products divisions and targeted at the 1,200-m (3,900-ft) NQ market, the upcoming Boart Longyear 4200 surface exploration drill features the safest and most flexible rod management sys-tem in its class. The rig includes the industry?s first, truly hands-free rod handling system. This increases operator safety on the jobsite. In addition to the rod handler, the rig also features many new innovations that boost productivity and rig efficiency while minimizing the risk of downtime due to component failure or operator error. Boart Longyear has also included an intelligent PC-based operating system designed to allow complete drilling control as well as diagnostics reporting for the rig.

Jan 1, 2009

By F. Habashi

Japan was a closed society until 1853 when it was forced to open to the West. Mining, metallurgical, and geological education started there around 1861 when a graduate from Yale University in USA went to Japan to organize the first School of Mines. This was followed by other metallurgists from Great Britain, France, and Germany and thousands from other disciplines. The present report is a summary of the writer's first contact with Japanese metallurgists and his visits to a number of universities and research institutions in the past years.

Jan 1, 2012

By Steven C. Borell

For more than a decade, changes have occurred each year that have improved the regulatory and business climate for mining in Alaska. These changes have taken place during Republican and Democratic governorships as well as when the state House of Representatives and Senate were controlled by either party. During some years, the changes have been relatively minor. In others, including the 2003 legislative session, the changes could only be characterized as massive. These improvements have encouraged exploration. This, in turn, has resulted in some major new discoveries. But Alaska is essentially unexplored and tremendous opportunities remain.

Jan 1, 2004

By S. Bang

In recent years, suction piles and suction anchors have been used as underwater foundations for various offshore structures. They have been proven very versatile, effective, and environmentally friendly. This paper describes the load resisting mechanism, installation, and design of suction piles and suction anchors. Also included are brief descriptions of three offshore structures that have recently been constructed using suction piles and suction anchors. They include: a new breakwater system utilizing gravity-type concrete caisson superstructure on top of concrete suction piles; a floating breakwater system utilizing embedded suction anchors; and a foundation system utilizing suction piles for temporary mooring of underwater tunnel elements.

Jan 1, 2009

By Gui DeReamer

Located on the Wabash River in the central portion of the state, the city of Lafayette, IN is relatively small compared to most cit-ies that incorporate tunnels into their combined sewer overflow (CSO) systems. The original CSO plan for the city was to replace two aging lift stations that were built in the 1950s. The original con-cept was to build a new sewer using conventional cut-and-cover construction to eliminate one of the lift stations ? the Parking Lot Lift Station ? and build a new regionalized one at the location of the Pearl River Lift Station. The initial sewer design was sized just to handle the flow that would eliminate the Parking Lot Lift Station. The planning for this project was being developed as part of the city?s CSO long-term control plan (LTCP) that focused on reducing the overflows from the city?s 14 overflow points. However, during the development of the CSO LTCP, a major industrial user indicated it would be increasing its flows to the system, which required additional conveyance capacity to meet the city?s CSO LTCP. After reviewing the design concepts with city representatives during the planning phase of the project, the mayor indicated that he wanted to minimize impacts to downtown businesses; therefore, trenchless alternatives were considered. The last piece of the puzzle that drove the project away from a small diameter pipeline was discovered during a flow monitoring program to collect flow data for the CSO LTCP project. This study revealed a major restriction in the 100-year-old Pearl River Trunk Sewer, located beneath four active railroad tracks. To eliminate this flow restriction, provide more overflow storage and reduce the impact to local businesses, a new 2.7- to 3.6-m- (9- to 12-ft-) diameter tunnel sewer became the most viable solution.

Jan 1, 2011