Search Documents

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008

By R. H. Oitto

To determine whether reflectors could substitute for the trip lights referred to in the Federal Mine Safety Code, the Bureau of Mines studied trip safety devices under simulated haulageway conditions. The noticeability of reflectors compared with trip lights and fluorescent panels was evaluated from distances of up to 850 feet with light source intensities of up to 1-6 foot-candles (ft c). Reflectors tested consisted of a reflective lens in a holder secured to a frame that can be attached to a trip. Reflectors were found to be suitable for use as a trip safety device. In fact, for the conditions in many underground haulageways some reflectors would be more effective than a permissible trip light.

Jan 1, 1968

By J. S. Stachulak

The Diesel Emissions Evaluation Program (DEEP), a research consortium formed in 1997 by Canadian mining companies, labour unions, and provincial and federal government departments, completed its work by mid-2006. This program, in which Vale Inco participated with both direct funding and in-kind contributions, investigated the ability of currently available technology to significantly reduce underground concentrations of diesel particulate matter (DPM) with high efficiency and low maintenance over a long-term period (years of life).While DEEP?s testing showed that engine maintenance is a critical component for lowering DPM, it was clear that reduction of DPM to the very low target levels of ~0.05 mg/m3 was not possible with maintenance alone. The best candidate technology for achieving low DPM levels was particulate filter systems. Furthermore, successful deployment of such systems was highly dependent on removing them from having to rely on human intervention for their regeneration. The search continues within Vale Inco to identify a reliable and rugged system.

Jan 1, 2009

THE solid nonmetallic inclusions that are present to some extent in all commercial steels have been variously designated. In early references they were usually called slag inclusions, and. this terminology is still retained to some extent. On the premise that all nonmetallic matter produced in a metallurgical process is slag, this can be justified. We have come to think of slag, however, in a more restricted sense, and calling these particles slag inclusions is further objectionable because it fosters the erroneous concept that they are actually incorporated portions of furnace slag. Rarely is this true. The term sonims (coined from solid nonmetallic impurities) was proposed many years ago but never came into common use. In general the term "nonmetallic inclusions" seems to be satisfactory and adequate. NATURE AND CONSTITUTION OF NONMETALLIC INCLUSIONS From the standpoint of origin, inclusions fall naturally into two classes: (1) those that occur as a result of reactions taking place in the body of the molten or solidifying metal and (2) those that result from the mechanical incorporation of refractories or other materials with which the steel comes in contact. The former are by far the more numerous and have been called indigenous, natural, or native inclusions. The latter are by their very nature sporadic in occurrence and have been called exogenous, accidental, adventitious, or foreign inclusions. They are often referred to as the "slag stringer" type, though here also the material is not likely to be furnace slag. Substances Found in Inclusions. Nonmetallic inclusions are composed principally of oxides and sulphidea but carbides and nitrides sometimes play an important role. In the case of indigenous inclusions the reactions by which these particles are precipitated from the molten or solidifying steel may be caused by (1) oxidation such as may occur during refining or during tapping and teeming, (2) deoxidation by added alloys, (3) change in equilibrium constants as the steel cools to the freezing temperature, (4) decreased solubility with lower

Jan 1, 1944

By R. G. B. Pickering

The purpose of this report is to chronicle the interaction between Anglo Platinum and Sandvik Tamrock during the development and application of Long Hole drilling as a viable, practical method of narrow reef mining. Appendix I identifies the people from Anglo Platinum and Sandvik Tamrock who participated in the project. Experiments in long hole drilling and blasting were conducted in a number of mines during the late 1950s and early 1960s. Some of the advantages envisaged were: ? The face would require no daily examination ? No barring down or immediate face support required ? No sockets to clean ? Only a few well drilled holes rather than large numbers of short blast holes ? Avoidance of poorly-marked holes, inaccurate drilling and improper charging ? Better supervision and better face advance. Holes 50 mm in diameter were drilled parallel to the stope face by pneumatic rock drills from advance strike gullies. Holes were charged with amon gelignite cartridges. All holes were traced with detonating cord to ensure propagation of the explosive along the entire hole length. Rock was blasted onto a rolling scatter pile. A number of reasons have been cited for the failure of this mining method. The two most important were: ? problems in controlling hole deviation which was exacerbated by the fractured ground ? difficulty of charging up holes in fractured ground, due to relative movement of rocks along fracture surfaces over the hole length. The idea of drilling a few long holes parallel to the face rather than a large number of short blast holes perpendicular to the face was an attractive option to mechanize narrow reef mining. This particular project started in 1998. Initial trial The Union Section of Anglo Platinum purchased a Solo H 606 RA long hole drilling rig from Sandvik Tamrock in 1997. In order to evaluate long hole drilling as a basis for face mechanization. The Solo series of drill rig was selected because it combines high drilling performance and good drilling accuracy with high versatility with a compact size. The mining method proposed by a consultant to Anglo Platinum was based on the current trackless mining method practised by Union Section. The trackless mining method is better described as a trackless development and transport method. Reef strike drives were installed approximately 40 metres apart on dip using trackless equipment. Reef was mined using hand-held pneumatic rock drills and scraper winches and the excavation was supported by sticks and crush pillars at the top of the panel. Rock scraped from the panel was loaded by Lad Haul Dumps (LHDs), trammed to an inclined haulage, and loaded into trucks for transport to the surface. It was intended that the Solo would drill from the bottom advance strike drive to the top advance strike drive. Blasted rock would still have to be scraped from the panel. It is also difficult to understand how well the support would have survived. In the initial motivation it was stated that drilling accuracy was of the utmost importance. Previous work by Sandvik Tamrock had shown that, in other parts of the world, 20 metre long holes could be drilled with a deviation not exceeding 100 mm provided that: ? holes were collared with low thrust pressure ? operating percussion pressure was kept low -often not ? exceeding 10 MPa ? drilling was to be with tubes, not rods. In early 1998 initial trials with the Solo H 606 RA were inconclusive; attempts were made to drill 40 metre long holes from one advance strike drive to another. Difficulty was experienced in measuring hole straightness and accuracy, there was no survey of the holes, and no blasting was done to expose hole barrels. A long hole mining system was then defined, with a corresponding face mining system, which led to the design of a test programme for the Solo drilling rig. Earlier experience at Telfer The proposed face mining system was based on a mining method that is practised at Telfer Gold Mine in Western Australia. Telfer has a series of domed reefs that dip at angles of less than 20° to more than 40°. The ore bodies are all thin, with widths from 0.6 metres to 0.8 metres. Figure 1 shows the face layout. Experience at Telfer indicated the following: ? The spacing and size of the dip pillars should be based on the rock mechanics of Union Section ? The length of the face is determined by the ability to correctly position the blast holes. Positioning of blast holes is a function of hole straightness and hole direction. Blast holes in Telfer were drilled 64 mm diameter with retrac bits from Sandvik. Extension steel was T38 by 1.8 metre lengths. A guide rod was fitted immediately behind the bit. To achieve greater accuracy' operators drill at relatively low percussion and thrust pressures. Results show that very good accuracy is achieved in 20 metre stopes and only fair accuracy in longer stopes. In 34 metre long stopes 10-15% of the holes are not sufficiently accurately positioned and have to be re-drilled. All blast holes are

Jan 1, 2006

By D. Duff, R. A. Cameron, R. E. S. Whitehead

"Although CO2 content indicates the quantity of carbonate in altered basaltic rocks, it does not measure the intensity of carbonate alteration. CO/CaO molar ratios, which correlate with the relative proportions of individual carbonate species, measure the intensity of carbonatization. The Timmins gold area is characterized by pervasive carbonatization, with large parts of the area having CO2/Ca0 ratios greater than 1, representing C02 supersaturation relative to CaO. The mean CO/CaO in the Timmins area is0.67, compared to 0.13 in two unmineralized control areas. Regional arsenic abundance in the gold-bearing area averages 4 ppm, compared to about 0.35 ppm for the non-mineralized areas. The average K20 and Rb abundances are similar in both mineralized and non-mineralized areas (about 0.30% K20 and 7 ppm Rb). Although there appears to have been no wholesale addition of K20 or Rb to the mineralized area from external sources, these alkalies have been redistributed internally, resulting in patterns of local enrichments and depletions which are characteristic of the mineralized region.Local target anomalies associated with known mineralization consist of CO2/Ca0 > 1.5, As > 10 ppm and K2O > 0. 75%. Not all three values are required to be above these thresholds in order to identify local targets. Combinations such as C02/ Ca0 > 1.5 and As < 10 ppm, CO/CaO 1-1.5 and K20 > 0. 75 or K20 > 0. 75 and As > 10 ppm are equally indicative of proximity to gold occurrences. Gold-bearing veins and associated anomalies occur throughout the entire volcanic succession and are not restricted to any particular stratigraphic horizons. The levels and patterns of alteration and occurrences of gold appear to be structurally controlled."

Jan 1, 1982

Performance of Dry Separation Processes in Cenospheres Recovery from Coal Fly Ash

Sep 13, 2010

By P. Venter, N. Naude

"Coal mining is a thriving industry and 53% of the coal mined in South Africa is used for electricity generation. Mechanization has made coal mining more efficient, but fines generation has subsequently increased. Up to 6% of the run of mine material can report to the -200 µm fraction. Common problems associated with fines handling include dust formation, storage problems, and high moisture levels. A method to turn this material into a saleable product instead of stockpiling it can add value to a company.Briquetting is a pressure agglomeration method where loose material is compacted into a dense mass (FEECO International, 2014). The briquettes must be able to withstand rigorous handling and transport operations without disintegrating. This study aims to investigate the optimum binder and moisture conditions required to produce a mechanically strong briquette using two different binders - a PVA powder (binder A) and a starch powder (binder B).It was found that for binder A the optimum moisture level was 12% to 14%. At this moisture level the greatest compression strength gains were observed, and low amounts of fines produced in impact and abrasion tests. The minimum amount of binder added while still obtaining a strong briquette was 0.5% binder A. For binder B the optimum moisture level was also 12% and the minimum amount of Binder B to be added was found to be 1%. Briquettes that were dried outside reached their peak strength after about four days, whereas the briquettes that dried inside took about 20 days to reach their strength plateau. Hardly any degradation took place on the surface of the binder A film after exposure of 300 hours of artificial weathering. Thermogravimetric analysis confirmed that neither binder A nor binder B will add to the ash content of the coal fines, as both binders totally decompose above 530°C.Binder B yielded stronger briquettes after 15 days and also generated less fines. It is therefore superior to binder A and would be recommended for further use.Paper written on final year project work carried out in partial fulfilment of B.Eng degree in Coal Beneficiation"

Jan 1, 2015

By P. A. Olubambi1

Representative samples of the hydrothermal vein deposits of the bulk complex sulphide ore deposit, 10 km south of Ishiagu, in Ebonyin State, South Eastern part of Nigeria were collected from two small scale mining companies. The samples were mixed and successively crushed in a jaw crusher and cone crusher, and ground in a rod mill. Characterization was carried out with SEM, EDX, XRD, XRF and ICP-OES. Mineralogical analysis revealed the presence of sphalerite, galena, siderite, pyrite, quartz and chalcopyrite. X-ray Diffractometry showed that sphalerite mineral in the ore occurs as sphalerite ferrous with varied percentage of Zn and Fe within the various sizes while chalcopyrite occurs as a chalcopyrite group mineral with chemical formula Cu2MnSnS4. Results of the elemental analysis showed variations in elemental composition within the different sizes.

Jan 1, 2006

By P. R. Clifford

Phosphogypsum is a byproduct of the manufacture phosphoric acid. There are approximately one billion tons of phosphogypsum stored in stacks in northern and central Florida. The Florida Institute of Phosphate Research (FIPR) is investigating potential uses of phosphogypsum. These include using phosphogypsum as a road base material, as a soil amendment in agriculture, as a daily cover in landfills, and as a construction material. The results of this research will be presented and will be discussed in light of regulatory barriers to the use of phosphogypsum.

Jan 1, 2002

By M A. Lund, C D. McCullough

In Australia and worldwide, open cut mining has become increasingly common over the last few decades through changes in excavation technology and ore economics. However, such operations frequently leave a legacy of open mine pits once mining ceases. Pit lakes will then form in mine pits that extend below the water table when dewatering operations cease. Pit lake waters are typically contaminated with metals, metalloids, saline or acidic/alkaline and rarely approach natural water body chemistry. Physically, pit lakes have unique bathymetries, are often strongly wind sheltered and have very small catchments. Nevertheless, pit lake waters often constitute a vast resource but of limited beneficial use (due to water quality issues); with a potential to contaminate regional surface and ground water resources. Water in pit lakes has the potential to be useful for a range of purposes in the Australian context of characteristic hot, dry climate and relatively few natural water bodies. Consequently, pit lakes can be seen to represent either a significant liability or a water resource to mining companies and regional communities. However, the lack of knowledge on pit lakes continues to hinder their proper management. This paper summarises the limited information currently available on water quality associated with Australian pit lakes. Information on pit lake occurrence, distribution and water quantity and quality is not nationally collated and requires immediate and ongoing attention from both mining companies and regulating authorities. Lack of a readily available database for pit lake occurrence, distribution and water quality fails to realise the potential for these water resources by both mining companies and Australian communities. Lack of access to pit lake quantity and water quality data may also lead to failure to manage this significant source of mining environmental risk.

Jan 1, 2009

By Fawad S. Niazi

Ever since the use of the cone penetration test (CPT) in geotechnical practice, attempts have been made to correlate CPT parameters with pile capacity components of unit end bearing (qb) and unit shaft resistance (fp), thus deriving multiple CPT-based pile design methods. These methods focus on "capacity" only without consideration to complete axial pile load-displacement (Q-w) response. Estimated capacities from these methods also exhibit considerable scatter without any consensus on their consistency. In addition, load-displacement curves obtained from axial load tests on highly expensive and extensively instrumented piles can exhibit different shapes. Nevertheless, a single value from the curve so obtained dictates the design capacity. Currently, there are at least 42 different criteria defining capacity with considerable variation in the values obtained thereof. The Randolph elastic solution, which provides a framework for analytical evaluation of pile load-displacement response, requires the profiles of soil stiffness. The fundamental soil stiffness defined by the small-strain shear modulus (Gmax) can be obtained from shear wave velocity (Vs) readings via seismic piezocone tests (SCPTu). The secant stiffness (G), which softens from Gmax corresponding to operational load levels, can be obtained by generating stiffness reduction curves from back analysis of load tests. Then, using appropriate G values, the Q-w curve can be defined for conditions similar to the database from the pseudo strain (w/d). Thus, a complete framework for optimal integration of SCPTu data, Randolph elastic solution and back-analysis of field operational stiffness can be established for complete axial pile foundation analysis.

Jan 1, 2011

By A. Sand

A 2-dimensional computational model based on the discrete element method (DEM) is utilized for modeling of stamp-charged coke making. In this process, a large volume of coal is compacted to one single coal cake before entering the coke oven. Cake densification and mechanical strength development are key factors for the subsequent production of a high-quality coke. An approach is introduced for model calibration utilizing multiple control parameters obtained from a laboratory-scale stamping device. Experimental data on stamper rebound amplitude, attenuation and peak force are compared with simulation output in a pairwise manner by constructing a criteria space, which allows identification of model settings best satisfying the control parameters. The calibration procedure carried out by multiple criteria comparison aided model parameter selection for reproducing stamper behavior in response to the properties of the cake subjected to compaction. This modeling and calibration procedure offers possibilities for numerically studying the densification and mechanical strength development of coal cakes. However, the approach is also more widely applicable to other compaction processes.

Feb 27, 2013

By Dale Dean, Bill Hancock, Raul Mondragon, Carlos Aguilar, Chris Martin

"In 1942, commercial mining operations began in what is now the Lucky Friday Ag/Pb/Zn mine in Idaho’s Silver Valley. Wholly owned since 1962 by Hecla Mining Company, the mine has produced more than 145 million ounces of silver and has been a mainstay producer in Idaho’s Silver Valley for over 70 years.However, by the early 21st century, the mill had fallen, technologically, seriously behind the rest of the industry. Accordingly, starting in 2005, the current mill management team set to revitalizing the milling operation. This paper will describe how the mill was systematically evaluated and the aging infrastructure replaced with more current technology. Driven by internal mill review studies supported by QEMSCAN mineralogical balancing, the mill has in recent years been through waves of upgrading – from the installation of new mechanical and column flotation equipment to the introduction of on-stream analysis, a technology well-accepted around most of the industry but alien to this technologically conservative mining district.The experience at Lucky Friday is a testament to the need for ongoing structured mill optimisation and technology upgrading in established mining operations. This paper will describe engineering experiences associated with upgrading equipment in an operating mill, contained in a confined building. Experiences in teaching the team new ways of operating a mill, and finally the metallurgical rewards that have been reaped will be described.INTRODUCTIONMining in Idaho’s Silver ValleyIdaho’s Silver Valley is a 64-km long valley flanked by the US Northern Rocky mountains, seldom more the 3-km wide, and stretching across much of Idaho’s northern panhandle, roughly 150 km south of the Canadian border. Mining has been continuously active in the area for more than 140 years, during which time, the Silver Valley has become one of the richest silver producing districts in the world, and as of 1985 had out-produced the 500 years of production from the famed Potosi district in Bolivia. Since 1885, almost 100 deposits have been discovered and worked in the district (Chapman, 2000)."

Jan 1, 2011

By Y. Z. Ma

This paper presents a matrix formulation of factorial kriging, and its relationships with simple and ordinary kriging. Similar to other kriging methods, factorial kriging can be applied to both stationary and intrinsic stochastic processes, and is often used as a local operator. Therefore, the concepts of intrinsic random function and local stationarity are first briefly reviewed. Kriging is presented in a block matrix form in which the kriging solution is useful not only for understanding the relationships between simple and ordinary kriging methods, but also the relationships between interpolative kriging and factorial kriging. When used as a signal/noise-filtering method, factorial kriging is especially useful for multiscale modelling. Examples for general signal analysis and geophysical data signal filtering are given to illustrate the method..

Jan 1, 2014

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of the cementation of cadmium, lead, and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu-Zn and Cu-Fe systems for which the reaction rate was found to be completely solution phase mass transfer controlled.When the amount of material deposited was greater than 0&#183;2 to 0&#183;4 mg/cm2 there was an apparent enhancement in rate which is attributed to the formation of a roughened deposit. This same phenomenon was observed in the Cu-Zn and Cu-Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass transfer controlled.

Jan 1, 1971

This paper reviews the development and operation of a small underground tin mine in NE Tasmania. Tin mineralisation was discovered in the Lottah area in the 1880s with early alluvial and eluvial workings leading to the development of large low grade open pit operations. Apart from short lived activities operations ceased in 1915. Intensive exploration in 1978 - 1981 outlined substantial tonnages of low grade tin mineralisation (0.2% Sn) of open pit material. An underground ore body was also located (800 000 tonnes 0.6 per cent Sn). Spectrum Resources Australia Pty Limited acquired a 98 per cent interest in the property in 1988. Mine and mill development began in early 1989 based on an underground mine utilising trackless mining using room and pillar with fill stoping. The milling circuit involves primary jaw crushing, Barmac secondary crushing to 1 mm, Mogensen and DSM screens with jigs and tables to make a wet concentrate. Final tin concentrates are produced by high tension and magnetic separation. Planned production rates are 500 t/day with a mine life of six to seven years.

Jan 1, 1990

By N. Sano

The chromium oxide in stainless steel slags usually exists as Cr2O3. However, there is a possibility that it is oxidized to hazardous CrO3 after disposal or during use. Therefore, some technical developments to reduce chromium oxide by using a smelting reduction technique have been reported recently. This paper describes the fundamentals of the technique which have been applied to ferrochromium production and reviews the recent results in literature.

Jan 1, 2004

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931

By Samuel J. Gambino

Preliminary recommendations for the Upper Northwest Interceptor 1&2 specified installation of reinforced concrete pipe using pipe-jacking methods. However, a larger one-pass tunnel constructed using precast segmental lining would provide additional storage volume. The risk of encountering unexpected conditions or events and the resulting cost impacts could differ significantly for these two options. A probabilistic life-cycle cost analysis of these alternatives was performed. This paper discusses the construction alternatives considered, the risk assessment methodology used to evaluate these alternatives, the input parameters and risk factors used in this analysis, and the recommended project which is currently being constructed.

Jan 1, 2008