Search Documents

By John D. Carr

Introduction The Flin Flon zinc plant operates on what is known as the low density or standard sulphate process, that is, the zinc is carried through the plant solution circuit attached to the SO4 or sulphate radical at a concentration not exceeding 175 grams per litre zinc. The process may be described briefly as follows: The zinc is received in the zinc concentrate chemically combined with sulphur and mixed with many other impurities. The concentrate is roasted and most of the sulphur is burned to a gas, which is discharged from the plant. The roasted concentrate, or calcine as it is called, is leached with a weak sulphuric acid solution so that the resulting leach solution contains a high zinc content but a very small proportion of the impurities. The solution is separated from the solids and is purified further by agitation with zinc dust to remove copper, cadmium, and cobalt. This purified zinc sulphate solution is then pumped to the electrolytic department. The solids from the first leach are again leached, but this time with a stronger acid solution to dissolve all of the remaining zinc which is soluble in the strength of acid available. The solids and solution from the leach are then separated. The solids are stock-piled for further treatment at some future date and the solution, carrying a relatively high amount of impurities, is sent to the first leach, where the chemical action is such that the contained impurities are precipitated as solids. The electrolytic department is nothing more than a large number of electroplating cells in which the zinc is plated on aluminium sheets. Since zinc does not plate tightly to aluminium, the zinc plating or sheet is easily stripped from the aluminium and the sheets are collected to be melted and cast into the standard market bars or slabs. In the electro-deposition cells, the zinc sulphate (ZnS04) is split to metallic zinc (Zn) which plates out, and sulphate (S04) which combines with the hydrogen of the water of the solution to form sulphuric acid (H2S04). When one pound of zinc is deposited, about one and one-half pounds of sulphuric acid are formed. This acid is sent to the leaching section, where it dissolves one pound of zinc from the calcine. The solution is purified and is again pumped to the plating cells. The solution travel forms a complete circuit.

Jan 1, 1935

By Linda Duncan, Trevor Yeomans, Chris Potorieko, Michael Fullam

"NVI Mining’s Myra Falls Operation is a 4,000 mtpd copper/zinc flotation circuit with by product gold of ~28,000 ounces per year. Gold recovery has historically averaged 40-55%, however, a portion of this was recovered in the zinc concentrate and received poor payment. Two Knelson CD-30 Concentrators have been operating in the grinding circuit since 1992, with gravity recovery averaging about 2-5% over that time period.The Myra Falls gravity circuit was one of the very first hard rock mining installations operating in the world with automated Knelsons. The mine has employed a unique and unusual upgrading method for the Knelson concentrate that had never been evaluated as to its efficiency. Recent Gravity Recoverable Gold Testing by McGill University, and mathematical modelling of the Gravity Circuit by Knelson Gravity Solutions indicated the gravity circuit was not living up to its potential. Myra Falls Personnel changed the upgrade system-operating regime, and a complete gravity audit of the grinding circuit was carried out, with the results confirming the initial suspicions. Gravity recovery increased from 5% to 15%, with overall gold recovery improving by 5%.INTRODUCTIONNVI Mining operates a 4000 tpd mine and mill complex on Vancouver Island. The milling circuit consists of open circuit rod milling, closed circuit ball milling, gravity recovery, copper flotation, zinc flotation, and tails disposal. There are two milling circuits, “A” circuit, and “B” circuit."

Jan 1, 2006

By Luis Alberto Martinez Tipe

The paper show how the inclusion of the uncertainty of the geology of the orebody into the mine planning and design process can be of great help, for the mine planner, in both assessing and quantifying the existing risk in the key project indicators such as DCF, and ore tonnage. This is achieved by using conditional simulation and Monte Carlo techniques which provide equally probable models of the original orebody model of the deposit. In this fashion, it is possible to assess the sensitivity of the pit design and related long-term production scheduling (cutbacks) to grade uncertainty.

Sep 12, 2005

By B. W. Gandrud

The upper part of the Alabama deposits of crystalline graphite consists of an oxidized ore derived from, the underlying unoxidized ore through prolonged weathering. The degree of oxidation in different sections and at different depths within the bed is nut. uniform. The original ore is hard and blue-gray; the weathered product is soft and brown and is the only part that has been mined to any extent. Samples of both oxidized and unoxidized ores were obtained from two of the large graphite deposits of Clay County. Three additional samples of oxidized ore were obtained from different portions of a third property in the same region. In this report, ores 1 to 5 are of oxidized material and ores 6 and 7 of unoxidized.

Jan 1, 1934

By T. Serradj

A study has been carried out to: develop a method for routine characterisation of rock strength and drillability through the particle-size distribution of crushed or drilled rock products, defined by the Protodyakonov index; establish correlations between the Protodyakonov index, uniformity coefficient and the constant grading equations; and propose an alternative rock characterisation index to classify rock strength and drillability for the northeast region of Algeria

Dec 1, 1996

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sinktimes were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1%, and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying, and dumping of coal products by comparison to airborne dust capture from sprays.

Feb 27, 2013

Interest in mining narrow, vein-type ones has increased world-wide during the last few years despite the fact that prices of metals have not risen in proportion as production costs of mining, such as labour and energy. In many mines, where narrow ones are mined, the mining technique and equipment used have been poorly mechanised. The mining methods have been cut-and-fill or shrinkage stoping. Pneumatic jack-legs have been used for drilling and slushers have been used for loading. The methods that have been used can be called the 'first-generation' methods. Work has been very hard for miners. It has been dangerous and exhausting. Production volumes of mines, and a s a result of that, also profits have been low.

Jan 1, 1990

By Jason Clarke, André R. Laplante

"The gravity-recoverable gold (GRG) ore characterization test was developed 15 years ago and has been applied to hundreds of ore samples. The test accurately determines the size distribution of GRG, at which grind it is recoverable, and the extent of its liberation above 150 µm. This contribution shows how the test can be simplified, what are the likely problems to occur, and what information is then lost. Two simplified versions of the test are presented, of which the simplest, grinding a 20-kg sample to a P80 of 75 µm, is retained as the best one. A database of 18 comparative tests is presented. The choice of the full GRG test vs. the simple test is discussed, as is the deportment of the GRG recovered in the standard test but not in the simplest test.INTRODUCTIONThe GRG test was developed in 1990 to characterize the progressive liberation of gold in representative samples of ores, with the primary objective of generating data for a gold gravity recovery model (Woodcock and Laplante, 1993; Laplante et al., 2000). Characterization includes the size distribution of GRG as well as the grind size at which it becomes recoverable. This is achieved in a 3-stage protocol of liberation and recovery using a laboratory centrifuge unit, a Laboratory Knelson Concentrator 3 inches in diameter (KC MD3). This protocol is shown in Figure 1. The first stage takes place at a F100 of 850 ?m (F80 of ~550 ?m), the second at F80 of 180 ?m, and the third at a P80 of 75 ?m. The rationale for the three cycles is the desire to preserve the original size distribution of the gold grains in the ore and to obtain a recovery grind size curve. The feed is a representative sample of ore that can be extracted from ore samples (e.g. drill core reject) or stream products of the grinding circuit other than circulating loads or product having undergone hydraulic classification (e.g. rod mill discharge or SAG screen undersize). Ideally the samples should weigh between 60 and 100 kg, depending on feed grade and gold top size. It is beyond the scope of this paper to fully discuss measures of representativity in the ore sample, for example Gy’s minimum sample mass model (Gy, 1979). However, further work in this regard may be an opportunity. The large initial weight facilitates representativity and minimizes weight and sulphide recovery to the concentrate (since concentrate weight is relatively constant at ~100 g), which limits the recovery of gold in nonsulphide gangue or gold carriers (i.e. sulphides). Thus, the 100 g concentrate carries principally discrete gold species, such as electrum, and native gold. The concentrate and a 600-g representative sample of gangue of each stage are screened down to 20 ?m and each size class is fire assayed (the concentrates to extinction, the tails up to 30 g per size class). The five coarsest size fractions of stage-1 concentrate are individually upgraded using a hydrosizer and the concentrates examined with an optical microscope to assess the degree of liberation of the gold phase. Scanning electron microscope work has established that the GRG has an excellent degree of liberation below 150 ?m in stage 1 and generally a good degree of liberation in stages 2 and 3 (Guerney et al., 2003); as a result the size distribution of the GRG has been found to approach closely that of gold grains (Nesset et al. 2005)."

Jan 1, 2006

By R. V. Ramani

This report is volume 2 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Geology and Reserves subsystem of the Master Design Simulator. The two functions of this subsystem are: 1) the design of a geological data library to provide input to the other subsystems of the simulator; and 2) the calculation of coal reserves and associated values and grades under various user-specified conditions. The subsystem uses a weighted moving average method to interpolate between the borehole values, and provides output in report format, graphical plots and/or storage on magnetic tape or other storage devices for later retrieval. The application of the subsystem as an independent model with test results and comparisons with other methods of computing reserves is also presented. The appendix comprises a users manual for the model, and includes a program listing.

Jan 1, 1974

By James P. Sloss

WHAT is the likelihood if any-that a real gold mining industry will be developed in the southern Appalachian region? Has the increase in the dollar value of gold from $20.67 to $35 per ounce potency to turn the trick? Suppose it be assumed that the price of gold will, at worst, not recede, and that the cost of digging ore and treating it of which the average level of commodity prices and wages is a fair index-will, at most, not exceed that prevailing in 1926. One may or may not accept these as reasonable assumptions; but one must arbitrarily remove some of the potential variables if one is to get anywhere on a problem like this. As a matter of fact, this article is not going to venture a conclusive answer to the question that has been posed; but it will endeavor to present some of the factors that have a bearing on the problem. The writer spent ten days visiting a dozen properties in Virginia and the Carolinas early in April, 1935, and in doing so got a first-hand slant on mining conditions in the domain of King Cotton.

Jan 1, 1935

By Charles Kocsis

Over the last few years a multi-faceted feasibility study has been evaluating the introduction of hydrogen fuel cell powered equipment into underground mines to replaced diesel engine powered equipment. The analysis has shown that under normal operating conditions fuel cells could at the very least be an environmental and health benefit by eliminating combustion engines and their unwanted by-products. However, they could also generate significant reductions in the amount of ventilation a mine needs to supply when compared to dieselized operations; this would further decrease a mine?s energy consumption, its associated greenhouse gas impact and also reduce a mine?s significant ventilation associated costs. Fuel cell powered equipment also has the advantage of lower noise and heat production compared to their equivalent diesel powered counterpart. The degree to which fuel cells can generate ventilation benefits in underground mines depends upon a number of operational parameters and mine specific qualifiers such as current ventilation control or management, mine depth, inherent dust conditions and minimum velocity requirements. However another major consideration in the introduction of fuel cells in underground mines will be the safety requirements associated with diluting and removing the potentially explosive hydrogen in the event of a gas leak. In outside surface applications, it is possible to use dispersion, buoyancy, time, and lack of ignition sources as mitigating factors in deriving a low risk of an explosion. However, in underground operations these factors change, dispersion and buoyancy are limited; time may not be available and in non-coal mines ignition sources are not typically controlled. When a hydrogen leak occurs, the availability of sufficient ventilation to dilute and effectively remove the gas will be critical, consequently ventilation may be the prime risk controlling factor. In this paper, the authors evaluate the potential benefits of replacing diesel engines with fuel cells in powered production equipment, discuss the mitigating qualifiers that could limit ventilation savings and evaluate solutions to retain and maintain an additional ventilation capacity in the event of an emergency situation such as a hydrogen leak from the fuel cell stack or its distribution system.

May 1, 2007

By Kara A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature, and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68 °C and 141 °C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large scale experimental configuration, the installation specifications of the fire suppression system, and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature, and limited water application on the suppression system performance.

Jan 1, 2010

By Zetti Gavelán

Lack of skilled workforce in mining industry during the current decade has been a serious concern for most mining organization globally. At the beginning of this decade the major envisioned difficulty was related to generational breach of mining professionals. By 2003, mining industry recover from a low metal prices cycle following by a worldwide mining investment boom in 2005 that triggers a talent war among mining companies that was not only limited to professional level but skilled operators as well. Despite world?s economy collapse in October 2008, impact on mining industry was small comparing to other industries and appears to show evidence of healing. Under this context, fundamentals that have been driven lack of skilled workforce for the mining industry in previous years still valid. Starting in 2007, Minera Argentina Gold SA - Barrick Veladero, subsidiary of Barrick Gold, initiated an innovative selection and training program for candidates without exposure to mining. Following our corporate social responsibility mandates, Barrick Veladero decided to change its hiring process entirely, concentrating on selection and training of local people with no experience rather than hire experienced mining operators. This paper shares Barrick Veladero experiences on its hiring program, challenges faced, and current results.

May 1, 2010

By Charles G. Maier

"INTRODUCTION The use of thermodynamic calculations to answer practical problems in metallurgy, especially those that are relatively difficult to test experimentally, is rapidly becoming a conventional method of procedure. Nevertheless, these methods cannot he applied effectively until the fundamental thermodynamic constants used for them have become available either by direct experiment or by recalculation of data already existing in more or less undigested form.In an attempt to collect such data far the compounds of lead and the antimony group the incentive has been to make a preliminary survey that will disclose the gaps or questionable phases of available information and to collect data that may be used to answer certain rather practical problems presented by operating metallurgists.This report comprises three sections; the first gives the basis of selection of the constants which may now be given or estimated, and the later sections discuss the application of the figures obtained to two of the more interesting problems.The reader will discover that many of the quantities involve critical study of a number of more or less discordant observations. Although certain data could be rejected on the basis of thermodynamic comparisons, it must not be overlooked that many of the figures are the results of rational estimates rather than exact experiment. The use of thermodynamic methods to control and partly authenticate such estimates is one of its most valuable characteristics for the practising metallurgist or chemist, who cannot check by direct experiment each property of the materials which he converts to usable form.Nevertheless, while it is definitely possible in certain instances that the final figure selected for the heat or free energy of a process or substance may be in error by as much as a few hundred to a few thousand calories per formula weight, questionable figures are usually revealed by the thermodynamic calculations made. When quantities of such degree of accuracy are, and they often must be, used for estimating an unknown reaction, the result often gives no more than the order of magnitude of the desired quantities. Yet even in these extreme cases the answer is far more reliable and valuable than an unordered guess or a conclusion based on incorrect data."

Dec 1, 1934

By Michael G. Zabetakis

The spillage of liquid diethyl ether in rooms at floor level and 3 feet above the floor resulted in flammable vapor-air mixtures in the immediate vicinity of the exposed liquido The liquid temperature was found to decrease by as much as 35° C., with a resultant decrease in vaporization rate. A search of the literature yielded numerous references to unstable peroxide (residue) formed by the autoxidation of ether. Such residues appear to constitute an explosion hazard in the condensed state.

Jan 1, 1962

By Thierry Bernard, Phillipe Cappello, Jean Marc Laboz

"The main reasons of the emergence of electronic detonators are linked to:-Local urban development close to mining operation sites-Environment regulations"

Jan 1, 1995

By P. K. Guerrero, N. Arbiter

The correlation of power consumed by a tumbling mill with the dimensions, speed, and load has been attempted by three principal methods. One of these, the torque formula, has been reviewed critically elsewhere.' This approach, while analytical, disregards the individual motion and speed of the tumbling bodies and assumes that the gross geometry of the entire load is sufficient to establish the power requirement. A more general approach, using dimensional analysis, has been applied in this laboratory by the present authors1'1, and more recently by Rose.3 This disregards the internal conditions within the mill entirely and in effect is an empirical procedure for correlating data. Finally, the complete analysis of tumbling mill dynamics as first made by Davis' attempts to develop the power requirement from individual ball and rod paths and velocities. Although Davis' result is applicable only at a single speed for a given size and load it could be useful, since his optimum speed is at the upper limits of conventional tumbling mill practice. Where power values predicted by the Davis equation were compared with actual mill requirements, they were found too low for small mills and much too high for the largest mills. This suggested that the agreement with actual intermediate range requirements might be fortuitous, and the development of the equation was examined critically. The probable source of error was found to lie in an erroneous assumption made by Davis in converting the energy of ball or rod motion to power. With the same approach, but with different assumptions, a modified equation has been obtained which predicts results that are usually consistently high. This is to be expected, since it is assumed that there is no slip between load and shell and no interference among tumbling bodies. Both these effects should account for the difference. Development of Equation: When a cylindrical shell charged with a substantial weight of rods or balls is slowly rotated about a horizontal axis, the load surface first assumes an inclination that gradually increases to a maximum. Continued rotation results in failure within the load, characterized by a sliding of the top layers down the slope and a reduction in the angle of inclination. Further rotation again increases the angle, and the cycle repeats. If the speed is increased, there is continuous load failure and build-up and a continuous stream of rods or balls descends over the upcoming mass, which moves in circular arcs. At higher speeds the up-

Jan 1, 1961

By David Oyler

Sonic travel time logging of exploration boreholes is routinely used in Australia to obtain estimates of coal mine roof rock strength. Because sonic velocity logs are relatively inexpensive and easy to obtain during exploration, the technique has provided Australian underground coal mines with an abundance of strength data for use in all aspects of ground control design. However, the technique depends upon reliable correlations between the unconfined compressive strength (UCS) and the sonic velocity. This paper describes research recently conducted by the National Institute for Occupational Safety and Health (NIOSH) aimed at developing a correlation for use by the U.S. mining industry. At three coreholes in Illinois, Pennsylvania, and southern West Virginia, sonic velocity logs were compared with point load tests for a broad range of coal measure rock types. For the entire data set, the relationship between UCS and sonic travel time is expressed by the following equation, where UCS is in psi and t is the travel time of the P-wave in microsec/ft. UCS = 468,000 x e-0.054t (1) The r-squared value for this equation is 0.87, indicating that a strong correlation between sonic travel time and UCS can be achieved with this technique. The paper also addresses the steps that are necessary to ensure that high-quality sonic logs are obtained for use in estimating UCS.

Jan 1, 2008

The Midvale Slag Site covers 300 acres in Midvale, Salt Lake County, Utah. Midvale (population 10,000) is part of the Salt Lake City metropolitan area (population 936,000). Between 1902 and 1971, United States Smelting, Refining and Mining Co. smelted ores on the site to produce copper, gold, lead, and silver. Figure 1 shows a picture of the historical Midvale smelter operations. [ ] When operations ceased, the site was estimated to contain 2 million tons of slag from these operations. The smelter no longer exists. In 1971, Valley Materials, Inc., acquired the site to process the slag into materials for railroad beds and asphalt highways. During the 1980s, the U.S. Environmental Protection Agency (USEPA) raised concerns regarding environmental impacts associated with the historical site operations. The Midvale Slag Superfund Site was listed on the NPL in 1991. The Site consists of two Operable Units (OUs): OU1 covering the properties north and adjacent to former ore smelting operations; and OU2 covering the smelter site itself. OU1 had historically been affected by wind blown slag dust and stack emissions occurring on OU2 and the Sharon Steel site further to the south. These emissions resulted in elevated levels of arsenic and lead in the native soils. The EPA issued the final Record of Decision (ROD) for the OU1 Site in 1995. The OU1 ROD required the implementation of institutional controls for the undeveloped portions of OU1 in order to restrict future land use to commercial/industrial purposes unless additional remediation was performed. Hence, the land comprising OU1 was originally considered in the ROD to be suitable for commercial or industrial purposes without the need for remedial action. However, development of OU1 for other land uses, including residential or recreational, would require additional assessment and probable remediation. The OU2 parcel was remediated by EPA to allow future land development, and the Sharon Steel site was remediated by EPA and deleted from the NPL. PROPERTY TRANSACTION AND REDEVELOPMENT In February 2006, a private development company, Mercer Bingham Junction, LLC. (MBJ) purchased 130 acres of the OU1 property for the purpose of performing environmental remediation, and developing mixed residential and commercial real estate. Development of the property was conducted in cooperation with USEPA Region 8 (EPA), the Utah Department of Environmental Quality (UDEQ) and Midvale City. The guidelines under which residential development could occur were defined by EPA. The 130 acres was to be developed for open space, residential and commercial use as part the Midvale City Bingham Junction development. Figure 2 shows the general layout of the proposed land uses. [ ] In May 2005, MBJ began pre-acquisition due diligence activities to purchase the 130 acres of OU1 north of 7200 South Street, which now comprises the Bingham Junction Development. This included the completion of Phase I and limited Phase II investigations. The Phase II investigations were performed to evaluate arsenic and lead concentrations in the planned residential areas of the site, and to explore the contents of the historic landfill on the property. The historic landfill area was on the far west side of OU1, adjacent to the Jordan River. Soil samples collected during the Phase II investigation showed that the planned residential parcels did not currently meet the criteria established in the Tech Memo and that additional placement of fill or soil excavation would be required for residential development in this area. An evaluation performed by the previous owner of the property, Littleson, Inc., showed similar results.

Jan 1, 2009

By Zhaohui Xie, Bin Xu, Qian Li, Yongbin Yang, Tao Jiang

A high carbon low-grade gold ore, in which gold mainly occurs in carbonaceous matters, is a typical refractory gold ore whose conventional cyanide leaching extraction is only 12.9 %. In this paper, by the process of flotation-roasting-leaching, gold was effectively enriched and extracted. The flotation results showed that the enrichment ratio of gold was relevant to that of carbon, indicating that gold occurred in close association with carbon. A concentrate containing gold 7.26 g/t and carbon 12.37 % was obtained, with gold recovery 83.10 % and carbon recovery 90.24 %. Subsequently, the roasting of flotation concentrate favorably made the removal rates of carbon and sulfur reach 99.81% and 98.79%, respectively. After roasting, the gold in the roasted product was further enriched to 29.70 g/t and the optimal gold cyanide leaching extraction reached 93.66%.

Jan 1, 2015