Search Documents

By Rob D. Morrision, Paul W. Cleary

"The best accepted method for design of autogenous and semi-autogenous mills is to carry out pilot scale test work using a 1.8 m diameter by 0.6 m long pilot scale test mill. The load in such a mill typically contains 250,000-450,000 particles larger than 6 mm, allowing correct representation of more than 90% of the charge. This scale of DEM model is now within the practical range of standard workstations running an efficient DEM code.This paper describes various ways of extracting collision data from the DEM model and translating it into breakage and wear estimates. Account is taken of the different breakage mechanisms (impact and abrasion) and of the specific impact histories of the particles in order to assess the breakage rates for various size fractions in the mills. These impact histories have the potential to be directly related to breakage as they most resemble the single particle breakage tests which are used by the JKMRC to calibrate more traditional population balance models for variations in ore behaviour. However, the specific impact histories also show a background of many low energy collision events within the mill. This Background may constitute what is usually regarded as “abrasion” breakage. As might be expected, high impact events are concentrated in the toe of the charge and near to the mill shell where the forces associated with the load bearing on each particle is more concentrated."

Jan 1, 2003

By Patrick O. Shires, Harry W. Schnabel

With stable building sites becoming scarce in the greater San Francisco Bay Area, the new Summit Senior Care Facility is being built into the side of an unstable hillside adjacent to the San Ramon Regional Medical Center in San Ramon, California. This hillside has had a long history of instability and the site of the new Senior Care Facility required excavation into both a historic old landslide and a more recent active landslide. After a thorough geotechnical study, it was concluded that the best way to build the new facility would be to construct a tied-back retaining wall in the area of the old landslide, since it extended off-site onto two adjacent properties, and remove the active landslide and replace it with compacted fill before cutting into its toe area with an additional tied-back retaining wall. The design was further complicated by the proximity of the site to several active faults. In the area of the old landslide, the combination of an ascending slope behind the wall, landslide forces and seismic forces resulted in total design pressures between 365 to 4,575 PSF for a wall with a maximum height of 30 feet. The wall for the old landslide was constructed by first drilling and placing steel soldier piles in concrete. The tip of the soldier piles extended a minimum of 12 feet below the landslide plane that was up to 36 feet below the bottom of the wall. Permanent double corrosion protected tiebacks were then installed through the soldier beams and anchored below the slide plane. A shotcrete facing was then installed on the face of the wall. BACKGROUND The site of the Summit Senior Care Facility is located on the southwest flank of Mount Diablo adjacent to San Ramon Valley which is characterized by gently rolling hills. The San Ramon Valley Regional Medical Center, which opened in 1990, is located to the north and an existing church is located to the southwest. There are also private residences located to the southeast. The site is shown in Figure 1. Numerous faults run close to the site, the most significant of which are the Calaveras and Pleasanton faults. The site has also had a long history of slope instability and has been the subject of numerous investigations. Studies conducted in 1979 and 1984 concluded that there was a landslide in the area and recommended that a buttress shear key be constructed between the subject site and the existing church for a sewer main as well as removal and replacement of the head area of the old landslide to stabilize the hospital site. While two previous geotechnical studies in 2008 and 2016 identified slope instability, they did not recognize the genesis and limits of the old landslide on the western portion of the site or the limits of the active landslide on the eastern portion of the site.

Jan 1, 2018

By J M. Galvin, B J. McKinnon

Lightning Ridge, Australia, is the largest opal producing area in the world. Most opal is mined from shallow underground mines by individuals or small partnerships with the industry having been protected from large-scale development to date. The safety performance of opal mining has lagged both general mining industry standards and community expectations. The application of geotechnical analysis to the opal fields has the potential to considerably reduce injuries and fatalities. With consideration of the local culture, preliminary geotechnical analysis has been applied to some current methods of work utilised at Lightning Ridge. Practical solutions have been advocated and are presented in this paper. Improvements to safety generated by these practical solutions indicate that further geotechnical research at Lightning Ridge is warranted and would be beneficial.

Jan 1, 2002

By K. A. Natarajan

Interaction with microorganisms results in significant surface chemical changes on minerals. For example, chemolithotrophs such as Thiobacillus ferrooxidans and Thiobacillus thiooxidans significantly alter the surface chemistry of several sulfide minerals such as pyrite, chalcopyrite, sphalerite and galena. Heterotrophic bacteria such as Bacillus sp. could alter the electrokinetic properties of oxide minerals such as hematite, alumina, silica, kaolinite and calcite. Microbe-mineral interactions could thus be beneficially utilised in mineral beneficiation as different from bioleaching. Microbially induced mineral beneficiation unlike bioleaching deals with interfacial phenomena at mineral-solution-bacteria interfaces and surface chemical changes are brought about at very rapid rates amounting to a few minutes resulting in mineral separations in an aqueous medium.

Jan 1, 2003

By Francesco Vegliò, Luigi Toro, Francesca Pagnanelli

"Different hydrometallurgical processes have been studied in order to recover manganese(II) from oxidised minerals such as MnO2 (Vegliò and Toro, 1994). An innovative acid reductive leaching carried out in soft experimental conditions was here considered using agro-industrial wastes containing carbohydrates as reducing agents (Vegliò et al., 1998).The leaching process was investigated from a kinetic and equilibrium point of view in order to optimize the experimental conditions and obtain high purity and concentrated MnSO4 solutions.The overall leaching process (not considering the complex network of intermediate oxidation reactions of the carbohydrates in hot sulphuric acid medium (Vegliò and Toro, 1994)) can be described by the following reaction:24 MnO2 + C12H22O11 + 48 H 24 Mn2+ + 12 CO2 + 35 H2O (1)A Shrinking Core Model (SCM) was modified by a variable activation energy term to take into account both the variable reagent concentrations and the reaction rate change with respect to the manganese dioxide conversion. The influence of the particle size in the kinetic model is discussed with the support of SEM analysis and BET surface measurements before and after leaching.Manganese extraction yield was maximised (170-190 g/L) using appropriate carbohydrates and acid excesses, while impurity concentrations were kept low (Fe<10ppm and Ca<300ppm) pre-treating the ores, using hydroalcoholic leaching medium and different combinations of down-stream processes. In particular precipitation, solvent extraction and adsorption onto active carbon were tested to eliminate Fe and Ca from MnSO4 solutions."

Jan 1, 2003

By J. Tian

"BHP Billiton carried out a pre-feasibility study on the LanPing zinc deposit to evaluate the possibility to jointly develop the zinc deposit into a large-scale zinc project with their Chinese partner. The unique characteristics of the complex LanPing zinc orebody and ore are 1) smithsonite (ZnCO3) as one of major zinc bearing mineral besides sphalerite, 2) varying and irregular oxidation degree of zinc (0 ~ +90%) in the different zone and depth of the deposit, and 3) varying host gangue from limestone/calcite dominant to quartz dominant, which requires a robust and flexible flotation process to recovery zinc from both sulphide and oxide efficiently.The conventional mineral processing flowsheets have been tested on the LanPing samples taken from the various orebodies by various parties during the past 20 years that includes a sequential flotation flowsheet that was tested in a demonstration plant using the mixed ore. The results of the demonstration plant runs show that the conventional oxide flotation using Na2S and amine collectors could achieve 50 ~ 75% of oxide zinc recovery at very high sulphidiser consumption for the mixed ore but the highly oxidised ore did not satisfactorily respond to the flowsheet in terms of performance consistency and efficiency of oxide zinc recovery, which is very crucial to the overall economics of the project."

Jan 1, 2003

By A. Steinmüller

Introduction In the design and operation of gravity concentration circuits, the application of process models for spiral concentrators offers significant benefits. A substantial amount of work has been produced over the last 30 years in the field of modeling the metallurgical performance of spiral concentrators. It is not the aim of this contribution to add to the refinement of modeling technique but to share some of the experiences and potential improvements which can be achieved in a relatively simple way. The design of spiral circuits usually requires extensive testing. This is often conducted in batch operation only, either due to lack of suitable continuous testing facilities, the unavailability of sufficient quantities of sample, or other constraints. Typical problems arising during circuit development from batch testwork are the extrapolation of results to different feed conditions, and resolving of internal recycles. Model selection and development The classic approaches in spiral modeling technique range from fundamental fluid dynamics, based on the Navier-Stokes equations in combination with expressions for local slurry properties, to fully empirical and statistical models. With the initial objective of developing an in-house tool for gravity circuit optimization and development, mathematical model types from each category, available either commercially or in the published literature, were evaluated. Model selection For the desired purpose, an approach proposed by Holland-Batt (1990) was found suitable, which was adopted and modified. Holland-Batt reported that the shape of release curves in spiral applications could be described by a combination of a linear function in the initial recovery zone, and a power law function outside this zone. The proposed recovery function was formulated as

Jan 1, 2005

By David P. Reddick

"Suncor Inc. Oilsands Group mining operation in Northern Alberta, Canada, has been blasting to loosen the oilsands to increase production and decrease maintenance of the bucketwheel excavators for over twenty years. In 1991 an area of the mine was encountered which had a working face of 130 feet rather than the usual 20 to 57. In order to maintain production objectives, the planning and blasting departments of the mine took on the task of blasting as much of the working face as possible. McGinnis Rathole Drilling Company provided the drilling for the project and Mining Services International (MSI) delivered the bulk explosives to the boreholes. It is believed the resultingblasts exceeded several known records in production blasting."

Jan 1, 1992

By Gerke Gilian, Pretz Thomas, Pehlken Alexandra

"The evaluation of health hazards within the treatment of mineral and waste materials is gaining more and more importance in industrial countries. The need to control occupational safety has been recognised, and regulations which describe general protective measurements for personnel provide a tool to protect their health. It is the aim of the paper to give an outlook for practical approaches to risk assessment and to present measures for exposure reduction in accordance with the state of the art in Germany.Both the treatment of minerals and of waste materials are described in relation to the risk assessment. The method of evaluating health hazards in the two industries is similar and therefore both examples are presented next to each other.The example presented in the paper is the German “Biostoffverordnung” (the regulation for biological materials) which is important for the waste treatment industry. All kinds of waste treatment facilities (like composting facilities, waste dumps, sorting facilities for packaging materials) are obliged to carry out an assessment of health hazards for a variety of working areas and working places. The possible safety requirements deriving from this regulation are presented and discussed under the aspect of biological hazards.All over the world each country has different guidelines and regulations but all have one target in common – to protect the employees. This can be achieved through a good management system of occupational health and safety. Therefore the health hazards have to be known and assessed.Principles of the assessment of health hazards are described through:Data collection on siteData evaluationAssessment of health hazardsDocumentation"

Jan 1, 2003

By Kot Unrug

Mine seals are necessary in nearly every mine to isolate mined-out areas from the ventilation network. There is a large number of seals in active mines and that number continually increases as the development spreads across the reserves. The recent accident caused by the failure of seals in the Sago mine resulted in new regulations. These regulations have been set based on a principle of eliminating the risk of failure, rather than the sound engineering and understanding of the conditions that may cause seal failure during an explosion of methane in sealed areas of the mine including the probability of such occurrences. This paper discusses the following subjects related to mine seals: The potential causes of methane explosions and the dynamic effects of pressure wave propagation. Seal materials and methods of construction in view of the interaction of the seal with the host rock environment as well as requirements for gathering geotechnical data. The design of seal dimensions is based on loading conditions, therefore the probable ranges of such loading is reviewed. There is also discussion of possible methods for shielding of seals from pressure pulses following an explosion. Particular seal?s types are examined in reference to the conditions at the seals location. A novel design is presented that will be a low- cost solution for the sealing of mined out areas. Recommendations are given for further research leading to a rational engineering system for design of new seals in coal mines.

Jan 1, 2008

By Peter N. Holtham, Mary M. Ng

"Resistivity measurements of minerals in the laboratory are commonly made with a low DC voltage source. Common test voltages specified in the ASTM Standard D257 are 100, 250, 500, 1000, 2500, 5000, 10000 and 15000 V, however 100 and 500 V are the most frequently used. Resistivity results obtained in the laboratory have been used to infer the electrical behaviour of minerals undergoing electrostatic separation. However because the voltages employed in electrostatic separation in the plant are of the order of thousands of volts, typically greater than 15000 V, whether the laboratory results are applicable as a predictor of plant performance is a critical question. It is unclear whether resistivity values taken at a low voltage are characteristic of those seen in electrostatic separation, in which the minerals are exposed to a much higher voltage. No definitive answer could be found in the literature.In this work, the resistivities of zircon, rutile and ilmenite were measured in a corona field for the first time. The measurement principle was based on a technique developed to measure fly ash resistivity in electrostatic precipitators, however the test apparatus and findings are novel.Resistivities of rutile and zircon were found to be easy to measure. The values measured in a corona field were several orders of magnitude less than those obtained with a dc voltage of 100 V. Evidence of back corona was observed with zircon. When the voltage drop was greater than the sample layer could withstand a localised electrical stress developed, resulting in a voltage breakdown, at which point a sudden surge of corona current (back corona) was detected in the sample layer. Rutile, on the other hand, exposed to the same conditions as that of zircon (i.e. same temperature and applied voltage) did not exhibit any sign of back corona. Its resistivity across the range of test voltages (14 to 33 kV) remained fairly constant."

Jan 1, 2003

By Albert Ruiz

South Coast Water District (District) operates the Beach Interceptor Sewer Tunnel (BIST) in South Laguna, Orange County, California between Mon-arch Beach and Aliso Beach (Figure 1). The 10,424-foot long BIST houses a 24-inch Techite gravity sewer pipeline critical to the District Sanitary Sewer Collection System that conveys 1 MGD of raw sewage to a wastewater treatment plant. The original tunnel was constructed in 1954 and the sewer line replaced in 1974. Periodic inspections by sewer pipeline maintenance crews have documented deterioration of specific intervals of the tunnel within the past few years (Sancon 2003). Rotting timber supports and rock falls in the tunnel as a result of the deterioration were endangering the sewer pipeline. A 50-foot section of the tunnel was determined to be in need of immediate repairs, which were carried out from January to August in 2007. This section was enlarged to a horseshoe shape and lined with shotcrete. The pipe was encased in concrete in the invert of the new enlarged cross section. Hatch Mott Mac-Donald (HMM) designed the emergency repairs, carried out an assessment of the rest of the tunnel alignment, and is currently developing a work plan for rehabilitating the entire tunnel.

Jan 1, 2008

By Mick Fritz, Tom Treleaven

The success of any blast is dependent on the accuracy of the blast design and field controls placed at the shot location. The procedure by which the data is collected and analyzed is paramount to accomplishing the anticipated blast results. lf the geometry of the blast is not measured correctly, then the results will not meet expectations. Measuring the geometry and compensating for bole hole deviations is crucial not only to the lnitlal blast but also for any consecutive blasts. Excessive bore hole deviation can cancel any new technology in use. However the instruments and skills required solving this Issue are readily available.

Jan 1, 1998

By Masaki Kitazume, Yoshiaki Kikuchi

"Abstract Pile foundation is one of fundamental techniques to improve the bearing capacity and settlement characteristics of superstructures. Wide varieties of piles having various shape, size and material were developed and have been applied to a lot of construction projects throughout the world. The deep mixing method, an in-situ admixture stabilization method, was developed in 1970s in Japan and the European countries, and has been frequently applied to many construction projects for various improvement purposes such as increasing bearing capacity and horizontal resistance, reducing ground settlement, preventing liquefaction and so on. The design methods, execution procedure and quality control and assurance (QC/QA) of the method are standardized or specified in many countries. These standards, specification and/or technical manual have been a remarkable contribution to spread the techniques throughout the world. The QC/QA is one of the major concerns for clients and engineers who have poor or no experience of the technologies. In order to assure the high quality of deep mixing work in the global market, it is necessary to establish the concept of QC/QA and correlate the output of different procedures. Upon the request by the organizing committee of the DFI-EFFC International Conference on Piling & Deep Foundations, the authors conducted survey of the specifications and standards on the piling and deep mixing technologies in Asian countries. In this manuscript, the results of survey are briefly introduced by comparing these specifications and standards.IntroductionThe pile foundation is one of fundamental techniques to improve the bearing capacity and settlement characteristics of superstructures. Wide varieties of piles having various shape, size and material were developed and have been applied to a lot of construction projects throughout the world. The design method, execution procedure and quality control and assurance of pile foundations are standardized in many countries based on the accumulate research results, laboratory and field experiences. In Japan, steel pipe piles are mainly constructed by hammer driven in port construction. On the other hand, precast pre-stressed concrete piles or cast-in-place piles are mainly used in on land construction. When precast pre-stressed concrete piles are constructed, piles are usually set by inner excavation method because of preventing noise and vibration problems. More than 50 years ago, noise and vibration problems had not been serious problem in Japan, but around 50 years ago, they became serious and now less noise and vibration construction methods are used for pile construction on land in Japan. In Asian countries, though piles used for construction have a lot of variety, precast pre-stressed piles are commonly used. In this report, execution controls of construction methods of steel pipe piles and precast concrete piles are mainly considered."

Jan 1, 2014

By Xie Jiyuan, Hu Yuehua, Yang Songrong, Zhu Zhansheng, Qiu Guanzhou

"By the end of 2000, the first bio-oxidation plant in China that designed by ENFI come successfully into commercial operation in Yantai Gold Smeltery. Its capacity is 50t/d of refractory gold ore concentrate. After the extension, the capacity of bio-oxidation plant reached 80t/d of refractory gold ore concentrate at end of 2001.The refractory gold ore concentrate treated is from different gold mines. After proportionate feeding, the feed typically consists of Au (52.7g/t), S (24.42%), As (3.58%).The bacterial culture used in the bio-oxidation circuit is taken from a mine in south of China, and has been grown over 20 years on a variety of sulfide concentrates in a laboratory of mineral processing, and has shown to be adaptive to growth in a high concentrations of arsenic. It is a mixture of mesophilic microorganisms. The nutrients used in the bio-oxidation process are (NH4)2SO4, KH2PO4, KOH.Before feeding to bio-oxidation circuit, the concentrate would be milled to minus 43µm. The biooxidation product is fed to solid/liquid separation system that consists of a thickener and two press filters, solid from the system is fed to CCD circuit, liquid from the system is fed to neutralization area. The neutralized product is fed to another solid/liquid separation system, and the solid from the system is disposed of on a wasted quarry pit, the liquid from the system is returned to bio-oxidation circuit for reusing."

Jan 1, 2003

By G. F. Vander Voort

The accident at Unit No. 2 of the Three Mile Island nuclear reactor (TMI-2) on 28 March 1979 was the worst nuclear accident in US history and crippled the nuclear industry. An international Vessel Investigation Project was formed to assess the integrity of the vessel. However, it was not possible to remove specimens from the lower head until January?March 1990. Fourteen of the fifteen specimens removed by electrical discharge machining were from under the debris pile that accumulated on the lower head due to melting of approximately 19 000 kg (45%) of the core. Specimens were previously cut from the lower head of a cancelled reactor of very similar size and design destined for Midland, Michigan. These specimens were subjected to controlled heating cycles with peak temperatures from 800°C to 1100°C for periods of 1 to 100 minutes. The initial study qualitatively compared the structures in the 15 specimens from TMI-2 to the control specimens from the Midland lower head. The writer used the same specimens and employed microindentation hardness traverses, electron microprobe analysis, and selective etching followed by quantitative metallography (by image analysis) to obtain a far more detailed description of the thermal exposure experienced.

Jan 1, 2013

By A. Fredriksson, R. Christiansson, I. Staub

A theoretical model based on DFN models and 2D DEM numerical modelling has been developed for evaluating the rock mass mechanical properties. The description of the methodology is non-site related and can be applied in any site for this type of characterisation. The methodology was developed in the frame of the Site Investigation programmes for a Deep Repository for spent fuel in Sweden, and validated on sets of data coming from the Äspö Hard Rock Laboratory. Un modèle théorique base sur des modèles probabilistiques de réseaux de fractures et sur un modèle numérique DEM 2D a été développé dans le but de déterminer les propriétés mécaniques de la masse rocheuse. La méthodologie développée peut être appliquée à tout type de site pour ce genre de caractérisation. Le modèle a été élaboré dans le cadre des programmes de recherche d’un site d’enfouissement des déchets nucléaires en Suède, et validé par une application au laboratoire de recherche souterrain à Äspö. Ausgehend von DFN-Modellen und 2D DEM numerischen Modellierungen wurde ein theoretisches Modell für die Auswertung von mechanischen Eigenschaften von Fels entwickelt. Die Methodikbeschreibung ist nicht standortspecifisch sondern kan überall für diesen Typ von Standordkarakteriserung angewendet werden. Die Methodik wurde in Schweden im Rahmen der Standortuntersuchungsprogramme für die Endlagerung von verbrauchten Brennelementen entwickelt und ist mit Hilfe von Daten des Äspö Hard Rock Laboratory validiert worden

Jan 1, 2003

DURING September, the Coal Commission pre- pared for issue a series of 18 reports on varied aspects of- the bituminous coal industry; the final report, dated Sept. 22, sums up the facts and offers recommendations addressed to Congress, to the industry, and to the public. The few following paragraphs are selected: Bituminous coal is the real foundation of that great industrial and transportation structure which enables more than a hundred million people to live in America and be so well supplied with things necessary for their health, comfort; and convenience; it also furnishes domestic fuel for two-thirds of the homes of the land. The distribution of the output of the bituminous mines tells the story: 28 per cent. goes to the railroads, 25 per cent. to the boiler houses of factories and mills of all kinds, 15 per cent. to the coke ovens and gas plants, 10 per cent, to the homes, 7 per cent. to steel plants and the same percentage to power plants and street railways, 4 per cent. is exported, 2 per cent is used for power at the coal mines, and the remaining 2 per cent. goes to the seaboard for steamship fuel. Bituminous coal enters into interstate commerce on a scale approached by no other commodity; less than a fourth of the coal mined in the United States fails to enter interstate com-merce. All but one of the 45 coal producing districts in the United States ship coal outside the State in which it is mined. Three hundred miles of cars loaded with coal is the daily output of the bituminous mines of the United States. The public-welfare element in coal is seen in the dependence of public health and safety on an unfailing supply of fuel, in the close connection between the prosperity of most industries and the uninterrupted operation of the coal mines, and in the obvious fact that without coal the great network of railroads which binds together this great country would be idle. The railroads and the public utilities, themselves so clearly obligated to render what-ever public service is demanded of them that the constitutionality of their public regulation is unquestioned, are of all industries most dependent upon coal. Thus, coal makes up over 35 per cent. of the operating cost at the gas plant and over 25 per cent. at the electric power station, and in the operating expenses of. a railroad the cost of coal is the largest single item, next to labor. The practical logic that half a century ago clothed with a public interest the steam locomotive and in later years the electric-power station must recognize a large element of public service in the coal mine that furnishes the necessary energy to both locomotive and power-plant.

Jan 10, 1923

By R. E. Whitehead

"Alkali/alumina and MgO/alumina molar ratio plots graphically portray both chemical and mineralogical changes accompanying potassic, phyllic, argillic, chloritic, and alunitic alteration of quartz monzonites and granodiorites hosting porphyry (as well as lode and greisen) ore deposits. The molar ratio plots can be used to identify different types of alteration. In most cases, the identification based on molar ratios coincides with petrographic data. In those instances where the molar ratio and petrographic identifications do not agree, the mineralogy might need to be re-examined. Hydrothermal alteration studies using trace elements could benefit from the application of complementary alkali/alumina molar ratio plots.Le diagramme des rapports molaires alkali/alumine et MgO/alumine illustre clairement les changements chimiques et minéralogiques qui accompagnent les altérations potassique, phyllique, argillique, chloritique, and alunitique des monzonites à quartz et des granodiorites encaissant les gîtes de type porphyrique, ainsi que des veines et des greisens qui leur sont associés. Les diagrammes de rapports molaires peuvent être utilisés pour identifier divers types d’altération. Dans la plupart des cas, l’identification basée sur les rapports molaires est en accord avec celle basée sur les données pétrographiques. Là ou il y a désaccord entre les rapports molaires et les données pétro-graphiques, il peut être nécessaire de réexaminer la minéralogie. Les études de l’altération hydro-thermale accompagnées d’une étude des éléments traces auraient avantage à utiliser un diagramme des rapports molaires alkali/alumine."

Jan 1, 2009

Study on Pure Mineral Flotation Tests of Low-Grade Phosphate Ore in Zhijin, Guizhou Province, China

Sep 13, 2010