Search Documents

By Larry Joe Linley

The Department of the Interior, Bureau of Mines is reviewing explosion protection methods for use in gassy coal mines. This performance criteria guideline is an evaluation of three explosion protection methods of machines electrically powered with voltages up to 15 000 volts AC. A sufficient amount of basic research has been accomplished to verify that the explosion-proof and pressurized enclosure methods can provide adequate explosion protection with the present state of the art up to 15 000 volts AC. The routine application of the potted enclosure as a stand alone protection method requires further investigation or development in order to clarify performance criteria and verification-certification requirements. An extensive literature search, a series of high voltage tests, and a design evaluation of the three explosion protection methods performed at White Sands Test Facility indicates that the explosion-proof, pressurized, and potted enclosures can all be used to enclose up to 15 000 volts AC, if the performance criteria and verification-certification requirements recommended in this guideline are implemented.

Jan 1, 1982

By B. V. Johnson

The Federal Bureau of Mines has conducted research in support of the National Aeronautical and Space Administration's (NASA) Apollo program to acquire fundamental scientific and engineering knowledge of lunar-mineral resources for NASA's Office of Advanced Research and Technology. Equipment and techniques were developed to conduct soil shear tests in a simulated lunar environment. Shear tests performed with this equipment in ultrahigh vacuum and controlled laboratory atmosphere showed that simulated lunar soil increased in strength in the simulated lunar environment.

Jan 1, 1973

By Jan A. Nemcik

Steel mesh has been used successfully for many years to control friable roof conditions and prevent loose roof and rib material from caving into the roadway. Despite its extensive use, the installation of steel mesh is difficult to automate and many other products have been evaluated as an alternative for skin control. Ideally, the properties of these new products should be similar or better than those of the steel mesh. In particular, development of a strong and resistant shell that minimizes movement along the fractured rock and coal surfaces between the bolt anchors is recommended. A strong surface adhesion and the strength of a reinforced polymer skin can provide the necessary toughening mechanism required to enhance roadway surface support by forming a reinforced polymer/rock surface layer. Most of the Thin Spray-on Liners (TSL) evaluated in the mines are weak with slow curing times, and the plastic mesh currently used to support the coal ribs is relatively weak. Therefore, neither material can seriously compete with steel mesh. Currently, a new polymer product that cures in seconds and forms an instantaneous strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong.

Jan 1, 2009

By Peter N. Holtham, Geoffrey J. Lyman, The University of Queensland, Matthew S. Brennan, Vijay Subramanian, Rui X. Rong

"The cyclone would have a claim to be the commonest, least understood and most abused piece of mineral processing equipment available for study by researchers. It has certainly generated its fair share of publications – 1,000 in the last 60 years would be a fair estimate. However this remarkable degree of interest and scale of investigation is not reflected in our understanding of how they work; cyclones are still installed inappropriately and run poorly, which suggests that there are still things to learn about this deceptively simple process.In mineral processing there are two broad classes of cyclone: the hydrocyclone, used in classification, thickening and dewatering, and the dense medium cyclone, used for concentration by density. Although rarely studied together, the laws of physics presumably apply equally to both and so it seems that there would be interesting things to learn by considering them as a single class of device. The good news is that in recent years there have been spectacular advances in the computational and measurement tools available to study these devices, including computational fluid dynamics (CFD), tomography, and laser doppler anemometry (LDA), and some good progress has been made in an understanding of the fundamental principles involved.The JKMRC has made many experimental studies of hydrocyclones and DM cyclones, leading to useful empirical models. However some recent CFD and tomographic work, in association with work of other institutions, has thrown important light on the workings of these processes. Progress has also been made in novel designs of cyclone to achieve improved separating efficiency, based on an attack on the subprocesses believed to contribute to inefficient operation. This paper describes the work to date.Modelling of the dense medium and classifying cyclone was conducted using the Fluent computational fluid dynamics code. Three phase simulations of the dense medium application (air/water/medium) showed appropriate medium segregation effects but over-predicted the level of segregation compared to segregation measured by gamma-ray tomography. This is believed to be because the basic Algebraic Slip mixture model in Fluent does not model any back-mixing of the dispersed phase due to turbulence."

Jan 1, 2003

By Ming Ju Liu

China has been suffering from the most serious coal and gas outburst accidents. The situation has become worse than ever with the mining of deeper coal seams at higher production rates in a more complex underground mining environment, in order to meet the huge national demand for coal-fuelled power plants. In the year 2007 alone, more than 30 outburst accidents occurred in underground coal mines with a death toll of 258, and in the year 2008, as of May 22, nine outbursts have already occurred in Henan, Hubei and Chongqing, killing 68 workers. At the same time, China also experienced new trends of coal and gas outburst accidents since its coal production boom in the year 2001. These trends are of great importance for government agencies, coal mine owners and operators to take initiative and effective measures to prevent and control the occurrence of coal and gas outbursts in China?s widely spread outburst prone mining areas. This paper presents outburst data of China coal mines since 2001 and describes new trends of outburst occurrence in recent years, which include outbursts coupled with shocks or rock bursts of competent roof, outbursts in mines under development, outbursts in new mines and mines that have never suffered outbursts before, outbursts in mines that are believed to be of low gas content as well as outbursts in more long-wall faces. Based on the observation of outburst occurrence in China in the period from 2001 to 2008 as well as mining and geological conditions, detailed analysis of the possible causes that led to those new trends of outburst accidents is conducted. The analysis helps shed light on possible future remedies and the necessary measures to alleviate or eliminate outburst accidents in underground coal mines. Suggestions are put forward on future studies that could be of interest to national and provincial government agencies regarding strategic policies, proper technical management practice, identification of outburst prone coal seams, online monitoring of impending outbursts as well as prevention and control measures.

Jan 1, 2008

By He Guangyi

Combining living examples, the paper introduces the controlled chamber standing shot of more than 3000t explosives initiated at one time with Nonel under complicated circumstances and the experience obtained to keep environment safe and favour mechanical rock cleaning.

Jan 1, 1998

By Fadeela Saloojee, Frank K. Crundwell

"Pressure leaching is an option for copper recovery from chalcopyrite. Leaching takes place at high temperatures and pressures in the presence of an oxidising agent. This work shows how the performance of pressure leaching circuits may be improved by optimising the configuration of autoclaves and the heat-removal method. The objective was achieved by creating an autoclave model by combining mass balances, energy balances and population balances. A base-case circuit consisting of a single autoclave was chosen, and this base case was compared with options for increasing capacity by adding more autoclaves to the circuit. These capacity–increase options include circuits in which the additional autoclave is added in parallel, in series and in series with thickening between the two autoclaves. The copper extraction, productivity and cooling requirements for these options are compared. The series circuit with inter-stage thickening has the highest extraction and productivity, however, the cooling duty in the first autoclave is high. In addition to comparing circuit options, three options for heat removal were investigated: cooling coils, quench water and flash recycling. The flash-recycle option results in the highest copper extraction, and the quench-water option gives the lowest copper extraction. INTRODUCTION Background Copper sulfide ores and concentrates containing chalcopyrite are typically hard to leach under atmospheric conditions. Smelting of these ores may also be a challenge, due to the inability of smelting processes to handle low-grade ores, as well as impurities such as arsenic and antimony. Alternative hydrometallurgical routes to treating chalcopyrite are therefore required. One option is pressure leaching, which is the focus of this work. In the pressure leaching process, sulfide ores and concentrates are leached in autoclaves at temperatures of 200 to 220°C and a pressure of about 3000 kPa (Schlesinger et al., 2011). An oxidising agent, usually oxygen, is required to oxidise sulfide ions to sulfate ions. The oxidation of sulfur to sulfate is exothermic; consequently, a method of heat removal is necessary in order to maintain the temperature in the autoclave."

Jan 1, 2015

By Jilai Xue

Experiments with various industrial cathodes ranging from 35 wt.% to 100 wt.% graphitic and fully graphitized carbons were carried out in a laboratory aluminum electrolysis cell. Sodium and cryolite bath penetration into the cathode samples was measured by XRD and SEM-EDS analysis. For a higher cryolite ratio in the bath, the cathodes with lower graphitic carbons exhibited more sodium penetration than the fully graphitized. The increased graphitization in the cathode materials can reduce Na, NaF and Na3AlF6 penetration. SEM-EDS inspection reveals that the sodium and fluorides penetration within the cathode samples has different patterns for varying graphitization of the carbon materials. XRD quantitative analysis indicates that there is a large percentage of Na3AlF6 in the penetrated bath. The results can provide useful information for quality evaluation of the industrial cathode products.

Jan 1, 2010

By J Dwyer, M Hill

Downer’s mining division has made an operational and financial commitment to developing engineered solutions that mitigate the risks associated with operator proximity to uncontrolled development drill boom movements, and unguarded rotating drill steels.With the potential for serious injury or fatality, these identified risks are categorised as critical. Previous attempts by the industry to engineer them out have produced limited success, with numerous incidents still occurring year on year. Ultimately, the industry (as a whole) remains reliant on procedural prevention for operator safety.Downer understood the success of such an initiative would largely depend on the effective collaboration between operational experience, technology experts and automation. With so many variables requiring consideration; such as physical operator movement, machine boom movements, variable machine positions, and underground environmental impacts – challenging traditional technologies was necessary to deliver an optimal solution.For that reason, discrete detection (similar to laser curtains or beams) was considered not fit for purpose. The use of situational mapping, using rotating lasers, however, provided the optimal solution. The lasers collect data that is then processed using a custom software application.The software application is specifically programmed for tracking and classifying objects within detection zones, using advanced algorithms and filtering. Recognition and removal of non-positive disturbances are possible without losing personnel detection capability. The detection of relevant classified objects (humans) is determined by analysis of object size, age, movement, and speed etc. When the relevant object is detected, an alarm and inhibit function is applied preventing drilling functions.Any breach of the safety zone (forward of the front jacks) will automatically disable the hydraulic boom function. This can only be reset in the cabin once the person or persons have returned past the front jacks of the development drill into the safety zone.Downer, in collaboration with partner YUMARR Automation, has successfully developed this reliable boom isolation system, and is called JumboGuard. The system has now been commissioned and installed across all Downer Mining development drill fleets, operating in Australia.CITATION:Hill, M and Dwyer, J, 2017. JumboGuard – automatic boom isolation system, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Nick Poushinsky

OVERVIEW OF PRESENTATION ?Stantec?s Northern Presence ?Challenges for Northern Development ?Environmental Approval Challenges ?History/Expectations ?Baseline Data ?Consultation ?Regulatory Processes ?Extra ?Regulatory ?Keys to Success

May 1, 2009

By P. G. Pigott

This Bureau of Mines laboratory research demonstrated that building bricks meeting ASTM specification C62-66 for grades SW and MW of FBS-type bricks can be produced from waste copper mill tailings. Waste tailings from accumulations at Magna, Utah, Anaconda, Mont., and Hayden, Miami, and San Manuel, Ariz., were dry-pressed into bricks, and the products were tested in accordance with ASTM Designation C67-66 on sampling, and testing of brick. An evaluation derived from pilot-plant production of similar brick at the Coal Research Bureau of West Virginia University indicated the production cost to be about $34 per 1,000 bricks. Utilization of such mill tailings on a commercial scale would eliminate the need for digging new pits for brick raw material production, conserve natural resources, and simultaneously remove potential sources of air pollution.

Jan 1, 1971

By M. M. Gadde

Recent regulatory changes in the United States make it mandatory to conduct structural analysis of coal mine seals used to isolate abandoned workings from active mining areas. Different loading criteria are available for seal design depending on whether gob composition is actively monitored and maintained or not and whether the gob conditions lead to deflagration or detonation type loading. Since the loads involved in seal designs are dynamic in nature, the structural analysis must be made using dynamic stress analysis techniques. However, because of the significant complexities involved in conducting dynamic analyses, some designers use approximate simplified techniques to address the design problem. In this paper two such simplified methods are critically evaluated for their suitability to design coal mine seals. The benefits and limitations of the simplified methods are also outlined. Some comparisons are made to show the differences between sophisticated three dimensional dynamic analyses and the simplified methods and to delineate the problems associated with the latter approaches.

Jan 1, 2009

By Paul Worsey, Seokbin Lim

There are two major types of shaped charges, conical and linear (Ref 1, 2). Conical shaped charges are used to perforate targets and are mainly used by the military as anti armor weapons and by the oil industry for oil well perforation. In contrast, linear shaped charges are primarily used to cut metal in the demolition industry with other uses including separating devices in the space industry. There is a large amount of material published on conical shaped charges because of the high level of defense industry research and funding, however in stark contrast there is very little published on linear shaped charges.

Jan 1, 2003

Collins Radio Company, through this contract with the Bureau of Mines, has conducted a System Study of Coal Mine Communi¬cations. The program was a three phase program to establish a data base, perform communication system analysis and optimi¬zation, and prepare equipment specifications to be included in this final report. At the start of establishing a data base both a knowledge of mine communication and coal mines in general was obtained. Communication system requirements and constraints were determined along with a survey of current and potential mine communication equipment. An investigation was completed concerning theoretical LF and VLF propagation characteristics, and UHF propagation tests were conducted in a working coal mine. Different mines were contacted and on-site surveys completed with respect to coal mine communication requirements.

Jan 1, 1973

By Pinakin C. Chaubal

An industry ? university consortium was set up to develop advanced tools necessary to understanding of the various phenomena occurring in the hearth of the modern iron making blast furnace. The major driver for this work was to provide the technological support required to extend campaign life of blast furnaces, which, by current agreement is tied to the life of the furnace hearth. The hearth wear is significantly affected by the hot metal velocity, temperature distribution and refractory temperatures. Due to the difficulty in making measurements inside the hearth, novel approaches to gain a fundamental understanding of the detailed physical and chemical processes in the hearth must be developed. The approach used in this project was to develop a 3-D CFD (Computational Fluid Dynamics) model coupled with extensive validation efforts. The CFD model is being utilized (1) to understand the phenomena in the hearth, (2) to understand the impact of changes in the internal conditions of the hearth on wear patterns; and (3) to design a monitoring/controlling system for prolonging campaign. In this paper, the results will be reviewed.

Jan 1, 2006

By Dave Bulled, Chris Bennett, Glenn Kosick, Glenn Dobby

"Mining companies around the world are embracing geometallurgical modeling at a rapid rate, as senior executives realize that inputs must be properly measured if the output is to be managed effectively. Geometallurgical modeling is used to scientifically manage risk in project evaluation, for plant design and production forecasting, and optimization of production planning and mineral processing/metallurgical unit operations. The technology also provides a solid foundation for implementing broad corporate strategies with respect to intelligent asset utilization and metal sales. Over the past five years, MinnovEX Technologies Inc. has been actively engaged in developing, promoting and applying geometallurgical modeling technology for major mining companies around the world. This paper describes the methodology for successfully applying the technology for the unit operations of comminution and flotation in the mining industry.INTRODUCTIONGeometallurgical modeling (referred hereon as geomet modeling), in theory, can be applied to its full potential on all unit operations in mineral processing; however, this paper will concentrate on two of the largest unit operations, namely comminution and flotation, where the technology is actually being practiced by many large mining companies. For concept studies and prefeasibility studies, aspects of geometallurgical technology are regularly applied but in a less rigorous manner than for final feasibility studies where justification for funds is sought. This paper will focus on the final feasibility stage of a project and on existing operations or planned expansions, where the full power of geometallurgical technology is brought to bear in a cost effective manner.One of the unique aspects of geomet modeling, when used to its potential, is the ability to design plants, and forecast and plan production with a quantifiable degree of precision, something that was unattainable in the past. This means that when new comminution and flotation plants are designed, the mining companies and financial institutions involved in the project can measure the precision of the design and therefore better understand and manage project risk. It means that for existing and new operations, metal sales personnel can carry out their sales strategies with a much better understanding of the degree of error associated with production forecasts of concentrate/metal and quality of concentrates. For mine and mill managers, geomet modeling allows the effect of the mine plan on the downstream processes to be quantified; thereby allowing the mine plan to be recast in a more optimized manner. Finally, existing concentrator personnel can optimize their unit operations based on a more definitive understanding"

Jan 1, 2004

By Chris A. Fleming

"Interest in the recovery of cyanide from gold and silver plant tailings has heightened in recent years. This interest has been spurred by several factors:Increasingly stringent regulations throughout the gold producing world, governing discharge limits for free and total cyanide to tailings ponds and the environment.The increasing cost of active chemical treatment versus passive (natural degradation) treatment of tailing, to bring them in line with environmental regulations.The worldwide trend to processing of more complex gold ore bodies, which is usually accompanied by higher levels of cyanide consumptions and greater concentrations of cyanide (particularly the copper cyanide complex) in tailings.The growing negative perception of the general public for the gold mining industry, due to several highly publicized cyanide spills in recent years (breaches of tailings dams, accidents involving trucks carrying cyanide to gold plants, etc.).The ability to recover cyanide from gold plant tailings has been known almost as long as the cyanidation process has been practiced, but there has been little incentive to process tailings in this way in the past. With the development of technologies that make it possible to recover and recycle free or complexed cyanide directly from gold plant slurry tailings, which indicates, on paper at least, the potential for significant cost savings compared to cyanide destruction, coupled with the introduction of legislation to seriously limit the discharge of cyanide to the environment in most gold-producing regions of the world, many companies are evaluating the cyanide-recovery alternative."

Jan 1, 2003

By Gary B. Petersen

The author has developed a seven-step process called the Applied Rock Mechanics (ARM) Protocol that the author has used to solve numerous roof stability problems in mines throughout North America since 1975. It is a practical evaluation process using trained observation, innovative data collection instrumentation, video borehole cameras, analytical processes, and controlled testing methods that have become highly effective in solving ground control problems in every type of underground mine. This paper will describe each of the steps of the protocol and how the rock mechanics engineer applies them to resolve a typical ground control problem.

Jan 1, 2012

By Ann Barron, Mark Abernethy

Along with the immense benefit of modern explosives seismic and acoustic effects caused by their detonation can be disruptive and alarming to many people. Claims range from affecting sexual performance to outright demolition of a residential structure. Regardless of the quality of the blast design and other precautionary measures, the inherent danger posed by the use of explosives often leaves residents searching for restitution. Consequently, many blasting companies today find themselves at the center of litigation. In the event that a blasting complaint proceeds to litigation your case will not be decided on “reasonable doubt” as in criminal trials. Instead, the jury will be instructed to decide guilt or innocence on a “preponderance of the evidence” presented. Even if you are able to present the best and most complete evidence that you have not caused the claim, the jury may rule in the favor

Jan 1, 2004

By Tamara F. Kondrateva, Evgenia E. Savari, Galina V. Sedelnikova, Rauf Y. Aslanukov, RAS (INMI), Grigori I. Karavaiko

"The investigation is dedicated to study of biohydrometallurgical processing of refractory gold-arsenic concentrate with the large content of pyrrhotite. Sulfide concentrate of chemical constituents: 75g/t Au, 4,7g/t Ag, 6,3% As, 29,3% S, 2,3% Sb, 0,5% ? (organic) and of mineral composition, %: 11,8 arsenopyrite, 39 pyrrhotite, 12 pyrite, 2,9 antimonite and the rest – aluminosilicates, carbonates and quartz, was studied. The recovery of gold from concentrate by cyanidation is 51,2%. The rest of gold is embedded as finegraded segregation in sulfides.Sulfide oxidation process study is described. Bacterial oxidation was executed on a pilot laboratory unit using combined autotrophic bacterium: A. thiooxidans , A. ferrooxidans, Leptospirillum ferrooxidans and sulfobacillus thermosulfidooxidation, pH=1,5-2,2, t=28-32?C, oxidation time 120 hours. Pyrrhotite is the least stable sulfide mineral with electrode potential 0,45V versus arsenopyrite (0,55 V) and pyrite (0,55-0,6 V) and is oxidated primarily. Pyrrhotite oxidation is followed by large amount of elemental sulphur, which has a bad influence on cyanidation.It’s established that the rate of arsenopyrite (for the first 48 hours) from concentrate containing 39% pyrrhotite is 2-3 times as less as the rate of arsenopyrite bio-oxidation from concentrate without pyrrhotite. The arsenopyrite bio-oxidation is accelerated only after the elemental sulfur was oxidized by bacterium A. thiooxidans and elemental sulfur percentage was reduced from 6,8 to 3,9%. The bacterium concentration is increased from 2,5x107 to 2,5x109 cells/ml. Almost full oxidation of arsenopyrite (98%) and pyrrhotite (98- 99%) is finished in 120 hours. We have studied two pretreatment methods for elimination sulfur content influence on cyanidation: aeration in lime and electrochemical treatment. Such an operation enables to have supplemental oxidation of elemental sulfur and other oxygen and cyanide absorbants before cyanidation. After treatment the content of elemental sulfur was decreased from 3,9 to 2,2%, gold recovery from 90 to 96% and cyanide consumption from 16,2 to 7,2 kg/t decreases. The content of toxical rhodonite-ions in liquid phase of pulp and disinfection reagents consumption were decreased as result of elemental sulfur content in bio-oxidated product reduction."

Jan 1, 2003