Search Documents

By E. Morrice

Solubility of yttrium oxide (Y203) in fluoride melts was experimentally measured in the temperature range of 998 to 1273 K and, YF3 composition in LiF.YF3 melts varying from 20 to 50 mole pct using a graphite crucible in an argon atmosphere. Solubility of oxide in the melt was found to increase with increasing temperature and YF3 composition in the melt. An expression for in XY2O3 as a function of temperature for several melts was deduced. The calculated activity coefficients of Y2O3 in the melts exhibited a negative deviation from Raoult's law.

Jan 1, 1989

By Gavin K. W. Freeman

The efficient separation of cobalt from nickel is a fundamental objective in the refining of cobalt. Based on recent experience at the Corefco refinery in Fort Saskatchewan, the identification of a novel process for the selective precipitation of cobalt from aqueous ammonia leach liquors is described. The addition of calcium sulphate, CaSO4.2H2O (gypsum), to an aqueous solution containing cobalt(III) hexammine sulphate, [Co(NH3)6]2(SO4)3, will result in the precipitation of a sparingly soluble double salt having the stoichiometry, [Co(NH3)6]2(SO4)3.2CaSO4.xH2O, where x = 4 or 6. Leach residues, which may contain a significant quantity of cobalt associated with the cobalt calcium double salt, can be washed with process solutions that contain ammonium carbonate. After contact with ammonium carbonate, the cobalt is recovered into solution, while the calcium is re-precipitated as the insoluble carbonate. The simplicity of this elemental separation and its high selectivity for cobalt, as well as the demonstrated usefulness in improving cobalt recoveries, are the basis for the potential applications of this process.

Jan 1, 2003

By Jian Li, S. Penttila, W. Zheng

"Materials selection for Gen IV supercritical water reactor in-core components faces major challenges due to severe operating condition. Beside high-temperature mechanical properties, SCC and general corrosion resistance of commercially available materials are also major focuses in recent research. Recent reports suggest that certain types of surface modifications are beneficial to SCW corrosion resistance. In this study, the effects of surface modifications are investigated, and possible mechanisms for improved corrosion performance are discussed.IntroductionThe current Canadian pressure-tube supercritical water reactor (SCW) design specifies a core outlet temperature of 625°C under 25 MPa of pressure, with peak cladding temperature as high as 850°C. Challenges in materials selection include high-temperature mechanical properties, corrosion resistance, SCC resistance and radiation damage. Most of the SCW corrosion test results available are below 730°C. Early work by Allen [1] summarized the corrosion resistance of alloy groups including Ni-based super alloys, stainless and ferritic/matensitic (F/M) steels that can potentially be used for SCW reactors. F/M steels can only be used at low temperature sites (e.g. down stream piping). At 500°C and 25 MPa, F/M steels develop a thick but mechanically stable oxide layer. However, the long term stability of the surface oxide layer is largely unknown. Ni-based alloys appear to form very thin surface oxide, however pitting was observed in the vicinity of some intermetallic precipitates [2-5], and dissolution of major alloying components could pose significant problems for down stream piping [6]. In addition, concerns of Helium formation due to Ni transmutation prevented this alloy group to be used as fuel cladding. The corrosion resistant austenitic stainless steels (e.g. 316L) are found to be susceptible to localized corrosion such as pitting, intergranular attack and stress corrosion cracking (SCC) [7]."

Jan 1, 2012

By Núbia Suely Silva Santos, Alexandre da Silva Crespo, Frederico Muylaert Margem, Sergio Neves Monteiro, Anderson de Paula Barbosa, Michel Picanço Oliveira

"Environmental considerations in addition to technical, economical and societal benefits are increasingly promoting the substitution of natural fibers for glass fiber in polymer matrix composites. However, natural fibers are heterogeneous in their dimensions, specially the cross section, which plays an important role in their mechanical strength. The fibers extracted from the petiole of the buriti palm tree is a relatively unknown but promising natural fiber for composite reinforcement. In this work, a statistical analysis of the density of buriti petiole fibers using the Weibull methodology was performed. An attempt to correlate the fiber density with the diameter, precisely measured by means of a profile projector, was carried out. The results revealed an inverse dependence between the buriti petiole fiber diameter and corresponding density. Fracture tip observation by SEM suggested a possible mechanism that could justify this inverse correlation.INTRODUTIONIn the past decade polymer composites reinforced with natural fibers obtained from cellulose-based plants, known as lignocellulosic fibers, have been applied in several engineering sectors, specially the automobile industry as both interior and outside component [1-4].Environmental benefits as well as economical, social, and technical advantages are actually promoting the substitution of these lignocellulosic for the traditional glass fiber in polymer matrix composites [5]. Today several lignocellulosic fiber are being extensively investigated [6-11] and considered for reinforcement of polymer composites. Some relatively unknown lignocellulosic fiber with reinforcement potential, however, still need to be characterized aiming at future application in composites. This is the case of the fibers stripped of from the petiole of the buriti palm tree, which is endemic in the central and northern regions of South America [12,13]. Preliminary works on the possibility of using the buriti petiole fibers as composite reinforcement, has shown favorable results [14,15]."

Jan 1, 2012

By Gaifeng Xue, Jingxuan Zhou, Shangchao Liu

"Both COD and TOC can characterize organic pollution of coking wastewater. In theory, there is a linear correlation between these two indicators. After continuous monitoring TOC and COD of coking waste water, linear regression relationship between of these to indicators was studied with the use of mathematical statistics. And conversion equation between these two indicators was established, and using t-test method for significance testing. The results showed that the linear relationship of COD and TOC was significant. Also interval estimation of equation slope and intercept were given in the condition of 95% confidence level. A linear regression equation established can be used to indirectly convert TOC to COD with high precision and accuracy.IntroductionBoth chemical oxygen demand (COD) and total organic carbon (TOC) are measure of the degree of characterization for organic pollution of water bodies. The current COD standard analytical methods is Potassium dichromate titration method [1] . there are some disadvantages in this method, such as only part of organic matter in the water bodies being oxidated, the refluxed steps, a long time needed for each measurement, high cost. It is the most important that sulfuric acid silver and mercury sulfate reagents used in the measurement may easily lead to secondary pollution. In contrast, the measurement of TOC is by the method of combustion or Photocatalytic Oxidation. The result could be easily got from the instrument. There are some advantages in this way, such as easy operation, short time and little expenses for each measurement and no secondary pollution 121• In addition, the measurement of TOC has higher degree of precision and accuracy than the measurement of COD both in the determination of calibration standards and actual samples. The meaning and contrast of TOC and COD are listed in the table 1."

Jan 1, 2013

By Chenhui Liu, Ka-ma Huang, Hong-ying Xia, Bingguo Liu, Hua Chen, Jinhui Peng, Libo Zhang

"The rising popularity of microwave heating in mineral processing has fuelled the need for knowledge concerning dielectric properties of minerals. Dielectric property and microwave absorption property of anthracite were measured over a temperature range of 20-100°C at 2.45GHz by using an open-ended coaxial sensor measurement system. The results show that the dielectric constant, loss factor and loss tangent increase with temperature rising at 2.45GHz. Microwave absorption properties of anthracite are highly dependent on temperature and frequency. At frequency of 2.45GHz frequency used in microwave metallurgy, anthracite is suitable for reducing agent to achieve fast elevation of temperature then returning to original state. The research will be helpful in explaining the thermal running of microwave dielectric heating the anthracite.IntroductionThe application of microwave heating in minerals processing and treatment has recently attracted great interest from the metallurgical industry. Compared with conventional heating methods, the advantages of microwave heating include rapid and selective heating, uniform distribution, high efficiency, fast on and off switching as well as flexible and modular design[l-3]. As a result of these advantages, microwave heating has been applied in a variety of mineral processing and extractive metallurgy, such as microwave-assisted ore grinding, microwave heating for carbothermic reduction and acid leaching of ilmenite ore, microwave drying, microwave-assisted roasting and smelting of sulfide concentrate, microwave-assisted spent carbon regeneration and microwave-assisted waste management [ 4-6]. Though the application of microwave heating in the metallurgical industry is promising, further studies on the interaction between microwave radiation and minerals and its effects are highly desired to develop innovative techniques for minerals processing and ore treatment using microwave heating [7]."

Jan 1, 2013

By Jeong-Soo, Joon Soo Kim, Rajesh Kumar, Sohn, Jin-Young Lee

"Liquid-liquid extraction (LLE) studies of tetravalent platinum from acidic chloride solutions have been carried out with Alamine 336 as an extractant diluted in kerosene. The title metal shows the inverse behavior at higher acid concentrations. Plot of log D vs. log [Acid], mol.L-1 gave a straight line with a negative slope of 0.8±0.03 indicating the exchange of one mole of hydrogen ions for every mole of platinum(IV) extracted into the organic phase. Extraction of platinum(IV) increases with increase of extractant concentration. The plot of log D vs. log [Extractant], mol.L-1 is linear with slope 1±0.3, indicating the association of one mole of extractant with the extracted metal species. The plot between metal distributions to aqueous to organic phases is 1.3±0.01; it indicates monomeric species was formed in organic phase. Stripping of metal from the loaded organic (LO) with mineral acids such as hydrochloric, sulphuric, nitric acids and bases like ammonia, hydrogen peroxide and sodium hydroxide are studied. The results indicated that hydrochloric acid and sodium hydroxide are the better stripping agents when compared with other acids and bases. Increase of temperature decreases the percentage extraction of metal indicating the process is endothermic. Regeneration and recycling capacity of Alamine 336 and extraction behavior of associated elements such as aluminium(III), magnesium(II), cobalt(II), iron(III) and nickel(II) were studied.IntroductionThe demand for platinum group metals (PGM’s) has risen in the last five years expected to keep in rising. Right now, the demand is already beyond the supply. The primary use of PGM’s today is in the automotive industry. Catalytic converters used in the PGM’s process to reduce greenhouse gases. Because of the current demand to reduce the green house effect the expected need for platinum is here stay. Country’s now advancing in the use of car production also are phasing increasing the needs for this metal. Chemical processing also use it, too. These industries account for more than 50% of all platinum production. Jewelry is other primary use of this precious metal whose value is much greater than gold. Other uses include computer data storage, scientific developments, fuel cell technology and in the glass manufacturing processes."

Jan 1, 2008

By Rush Kramer

A bulk compositional chemical analysis often provides incomplete information to help the mineral processor when faced with the problem of removing troublesome contaminants in low concentrations. Michigan Tech has developed a unique approach for addressing this problem. A combination of Scanning Electron Microscopy (SEM). Energy Dispersive Spectroscopy (EDS). and image analysis was successfully used to characterize the species responsible for phosphorus contamination of less than .05 weight percent in iron ore. An automated routine acquired the chemical signature of each particle on a backscattered electron image. The few particles containing phosphorus were identified from the hundreds of particles examined. and the phosphate phases present were easily characterized.

Jan 1, 1991

By A. V. Tarasov

Technology has been developed for production of elemental sulphur from off-gas from autogenous smelting processes based on reduction of sulphur dioxide with natural gas with subsequent treatment of reduced gas containing hydrogen sulfide by the Klaus method. This technology has been applied on a commercial scale at the copper smelter of the Norilsk Mining and Metallurgical Complex for treatment of off-gas from the Vanyukov smelting process (PV). In the course of further improvement of the technology a catalytic version of the process has been developed based on the use of a catalyst at the reduction stage, which permits a decrease in the natural gas requirement by 25% to 30%.

Jan 1, 2006

By J. G. Peacey, P. Hancock, R. -Q. Li

A pyrometallurgical process for the direct recovery of zinc from zinc concentrates and zinc/iron residues has been proposed and tested extensively by Noranda. The process consists of smelting bone-dry zinc containing materials (sulfide concentrates and secondary zinc/iron materials) in a molten iron oxysulfide bath to volatilize metallic zinc into a SC^-free offgas. Sulfur contained in the feed materials is fixed as an iron oxysulfide matte for disposal. Thus, this process not only is capable of treating zinc sulfide concentrates and secondary zinc materials simultaneously, but also eliminates the need of sulfuric acid production. Detailed thermodynamic analysis and experimental test work are described in this paper.

Jan 1, 2000

By A. S. Mustafinova, A. A. Zharmenov

"Production of electrolytic copper is characterized by large volumes of acidic spent solutions the utilization of which requires considerable expenditures of neutralizing agents. At present, an economically substantiated technology does not exist for treatment of sulfuric acid rinse solutions and spent copper electrolyte which will allow for repeated use of the acid and the metal salts. Therefore, for this aim the most advantageous is the use of electromembrane methods. In the paper there is stated the essence of developed technologies which are distinguished by low waste and provide the extraction from the solutions of metallic copper, nickel and sulphuric acid. There are also considered methods of copper electrolyte processing allowing to regulate its composition by that or another component (H2S04, Cu, Ni, As).On the base of the detailed study of the behaviour of various types of ion- exchanger membranes in copper-, nickel-, zinc-, arsenic- bearing sulphate solutions there is realized the selection of the most suitable membranes (MK -401, MA-411, MB-2 and MKL-l/MAL-2).Some variants of electro membrane processing of spent solutions of the hydrometallurgy process have passed productions tests on a number of copper-electrolyte enterprises of the countries of CIS (cooperation of Independent States). These tests showed high efficiency of developed methods."

Jan 1, 1997

By P. R. Bruggink

"A quantitative tool has been developed to assess the impact of changes in recycling rates on the environmental impact of aluminum supply. It has been applied to the USA to forecast sources of aluminum scrap and to examine the impact of an increase in Old Scrap recovery on the USA supply system and the subsequent effect on the Life Cycle Impact of aluminum supply. The reported data for primary, secondary and import/export supply and product shipments for aluminum in the USA show a fairly good balance between supply and demand on average over the years. Therefore, it is reasonable to use the data, along with published estimates of average product lives, recycling rates and recoveries to draw conclusions about future aluminum scrap generation· and recovery. The Life Cycle Impacts of increasing post-consumer recovery rates to recover an additional 450,000 MT/yr (1 billion lb/yr) has been estimated using the model.The spreadsheet model upon which this work was based was developed in U.S. Customary units. Converting the figures to Metric units would have required converting the entire model and rebuilding the figures. I have chosen to leave the figures in U.S. Customary units. I apologize for any inconvenience this may cause."

Jan 1, 2000

By C. G. Anderson, L. G. Twidwell

"Throughout the world, there are many orebodies or materials which have significant value but also contain arsenic, antimony, and mercury. As regulations on the transport, exposure, disposition and emission of these elements have become more stringent; it has become increasingly more difficult to derive the values from the resources. This paper outlines the fundamentals of alkaline sulfide hydrometallurgy and its successful application to arsenic, antimony and mercury bearing ores, concentrates, by-products, and other materials.Fundamental Alkaline Sulfide HydrometallurgyHydrometallurgical methods can be employed for treatment of gold, arsenic, antimony, tin and mercury containing materials, concentrates and ores as well as complex ones containing any number of metals. The alkaline sulfide system is one of these and is essentially a mixture of sodium sulfide and sodium hydroxide. This is a unique hydrometallurgical system as it is a very selective lixiviant for the distinct leaching of tin, gold, antimony, arsenic and mercury [1-7]. Worldwide, it is employed industrially in the CIS, China and the United States for the production of antimony [8-15].As an example, when the system is applied to an arsenic containing material like orpiment, As2S3, a solution of sodium thioarsenite is formed. This is illustrated as:"

Jan 1, 2008

By S. H. Castro

In 1997 Chile was the world's largest copper mine producer with around 3.4 million metric tomes of copper. Conventional technology (conminution-flotation- smelting-converting-electrorefining) for copper sulfide ores was used. For copper oxidized ores hydrometallurgical processes (heap leaching-solvent extraction- electrowinning) were employed. Consequently, the most important waste effluents include flotation tailings, gaseous emissions, smelter slags, acidic and alkaline wastewater, electrolytic sludges, solid residues from leaching, etc. The introduction of stricter environmental regulations are forcing the Chilean industry to minimise the generation of waste and promote cleaner production. Gas emissions such as SO2 and arsenic from smelters and process wastewater are the major problems at this stage. The environmental impact assessment of gas emissions in all six largest smelters namely Chuquicamata, Caletones, Potrenllos, Ventanas, Paipote and Chagres led to design a "decontamination plan." The implementation of this plan resulted in (i) the installation of sulfuric acid plants for SO2 abatement and (ii) the installation of electrostatic precipitators to remove arsenic oxides condensed from cooling gases. The aim of this paper is (i) to describe the type of waste associated to the various stages of the metallurgical processes and (ii) review the main abatement technologies used in medium and large size companies.

Jan 1, 1999

By XUEWEN WANG, Xingming Wang, Xuehui Liu, Mingyu Wang

The Panzhihua titanium concentrate contains high contents impurity of Mg and Al, and it is difficult to prepare high grade titanium slag. To solve this problem, a sodium salt roasting-acid leaching process was proposed for removing the impurities in titanium concentrate. Na2CO3 and titanium concentrate were mixed with the proportion of 1:4, and then the mixture was roasted at 700 for 2h. After roasting, the calcine was leached with HCl solution. The experimental results showed that the removal rate of silicon and aluminum can reach more than 85% and 80%, respectively, at leaching temperature of 70 , leaching time of 4h, HCl addition of 5ml and liquid-solid ratio of 4:1.

Jan 1, 2016

By S. Kurama

Incorporation of de-watering sieve waste of borax (TSW) from Etibor Kirka Borax Company (Turkey) on the mechanical and physical properties of a commercial floor tile composition was investigated. In order to achieve this aim, TSW was partially employed in place of feldspar in the standard composition up to 20 wt %. The formulated compositions were wet milled, dried, shaped and then fired at 1190C for a total firing time of 38 minutes (from cold to cold) under industrial conditions. It was found that using of TSW up to 15 wt % improved the physical and mechanical properties of final product. The results indicated a good prospect for TSW as a co-flux in floor tile formulations.

Jan 1, 2006

By Gaifeng Xue, Lei Zhang, Xia Liu, Lina Wang, Pu Liu, Benquan Fu

"Experiments were conducted to investigate the behavior of the integrated process with a three-dimensional electrode reactor combined with Fenton process for coking wastewater treatment. Effects of initial pH value, reaction time, H20 2 dosage, Fe2+ dosage on Total organic carbon (f OC) removal rate were investigated. The kinetics of degradation of TOC from coking wastewater by three-dimensional fluid bed electrode reactor combined with Fenton process was also studied. Experimental results shows that three-dimensional fluid bed electrode reactor combined with Fenton process had better synergic effect, average 17.4% TOC removal rate was improved within an hour. It was found that TOC degradation in coking wastewater followed a pseudo-first-order reaction kinetic model. The optimum degradation efficiencies of TOC were up to 60% as pH3.4, 3.5 mM ofFe2+ andl.2-1.8ml/L H20 2 in 90min reaction period. Furthermore, the integrated process showed a rapid reaction performance at a low temperature within a short reaction time and remained high efficiencies for TOC removal. Overall, the integrated process was proved feasible for coking wastewater treatment in practical applications.IntroductionCoking wastewater is generated from coal coking, coal gas purification, and by-product recovery processes of coking, which is composed of phenolic compounds, heterocyclic compounds, polycyclic aromatic hydrocarbons, ammonia, cyanide, polycyclic nitrogen-containing aromatics, acyclic compounds, etc. Most of these constituents are refractory, poor biodegradability, toxic and carcinogenic['-31. Currently, coking wastewater is usually treated by different forms of A/O biological nitrogen removal process as the primary treatment process, but the aforementioned processes are not efficient enough to meet the requirements from the National Discharge Standard in China (GB13456-1992). According to the continuous requirement on improving environmental protection for coking industry (revised 2008), increasing wastewater utilization ratio and reducing discharge of effluent in the coke industry has to be implemented for cleaner production and sustainable development. Therefore, advanced technologies need to be developed to treat coking wastewater and reutilize the product as industrial cooling water, which would be one of the best choices to achieve zero discharge of wastewater and reduce water consumption per ton of steel [4-51 . In this study, three-dimensional fluidized bed electrode reactor combined with Fenton process was adopted to advanced treatment of coking wastewater, and the effects of operating conditions, including H2O 2 dosage, Fe2+ dosage, initial pH, and reaction time on TOC removal rate, were investigated. Meantime, study of kinetics of reaction was estimated."

Jan 1, 2013

By Mark Samonds

"Manufacturing processes which involve liquid to solid and solid state transformations in metals encompass a wide variety of physical phenomena. The past twenty years have seen a steady evolution in the complexity and scope of numerical models of these processes, beginning with thermal analyses without phase change. Recently, a few software packages have become available which have true multi-physics capabilities. This permits the treatment of thermal, fluids, stress, electromagnetic, chemical reaction and microstructure development aspects altogether in a fully coupled simulation. This paper will consider various aspects of these types of models.Coupled thermal and fluid flow analyses of continuous castings have been around for fifteen years. Coupled thermal and free surface fluid flow simulations of shape castings have been available for ten years, including view factor radiation models for investment castings. Only recently, however, have fully coupled thermal, fluid, and stress analyses become practical. This implies the reverse coupling of the mechanical deformations to the solution of the energy and momentum equations through modification to the interface heat transfer coefficients and the fluid domain geometry. This has been implemented with a combined eulerian-lagrangian finite element method. Appropriate mechanical constitutive models will also be discussed.Many types of defects need to be predicted in casting processes. Those related to stress include hot tearing, hot cracking, part distortion, and thermal fatigue in dies. Macroporosity, microporosity, and microsegregation are determined by the solidification behavior and microstructure development in a casting. In particular, microporosity is influenced by dissolved gases, the morphology of the mushy zone, the liquid to solid density change, and the local pressure conditions. Macrosegregation is caused by the partitioning of solutes during. solidification and subsequent thermo-solutal convection. An additional transport equation is required for each solute that is being tracked. Computational thermodynamics is being incorporated into these types of analyses to determine transformation temperatures, partition coefficients, densities, and enthalpies. In combination, the microstructure and microporosity models can frequently predict a variety of mechanical models, such as yield strength, tensile strength, and elongation."

Jan 1, 2001

By Dan Wang, Qian Li, Yong-bin Yang, Tao Jiang

"Thiosulfate is one of the most promising non-cyanide lixiviants for gold leaching. However, the undesirable reaction between thiosulfate and copper (II) gives rise to increased reagent consumption, which results in high cost and huge limit to its development. This paper presents study on the effect of ammonia, copper (II) and Cu(NH3)l+ ions on the oxidative decomposition of thioulfate. It shows that the presence of copper (II) and Cu(NH3)l+ can significantly increase the thiosulfate oxidation, while ammonia is relatively unaffected. The oxidation of thiosulfate by copper(II) in the absence of ammonia is fast at first and then decreases as time increased within a certain time, which can postulate that an intermediate product is responsible for the decreased consumption. The effect of ammonia is depended on the interaction with copper (II), which was found to significantly affect the consumption of thiosulfate.IntroductionFor over one century cyanidation is widely used in industrial production of gold, due to its simplity of process and low cost of production. However, cyanide is a highly toxic chemical reagent used dangerously and brings serious environmental pollution. What's more, cyanidation has slow speed of leaching gold and poorly leaching effective for refractory ores. With the exhausting of free-milling gold ores and promoted environmental protection requests, the disadvantage of cyanidation becomes a growing problem. In recent years, more and more research activities have been focused on alternative processes using non-cyanide lixiviants. Among the non-cyanide lixiviants, thiosulfate is considered as the most promising one[l-5].Compared to cyanide, thiosulfate is an inexpensive, nontoxic and less-pollution reagent, which can form complexes with many metal ions. Thiosulfate leaching of gold has an acceptable leaching rate and is insensitivity to impurities. Moreover it presents advantage on the treatment of refractory gold ores such as carbonaceous gold ores, copper gold ores, complex arsenic and sulfur gold ores, and so on[6]."

Jan 1, 2013

By Xinli Wang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng, Byoung-Gon Kim

"The microwave dielectric properties of silicon dioxide at frequencies of 915 and 2450 MHz were characterized in the temperature range of 24 to approximately 1000 °C using the cavity perturbation technique. It is shown that the relative dielectric constant of silicon dioxide at both frequencies remains almost unchanged below 500 °C, above which there is a slight increase of 2%. The relative dielectric loss factor of silicon dioxide exhibits a strong temperature dependence above 500 °C and increases by approximately 7 and 5 times at 915 and 2450 MHz, respectively. The substantial increase in the relative dielectric loss factor is mainly attributed to the enhanced dielectric polarization and accelerated electrical transport in silicon dioxide at elevated temperatures.IntroductionSilicon dioxide (Si02) is usually considered a microwave transparent material due to its poor absorption capability at room temperature [1]. This characteristic has led to various applications of silicon dioxide in microwave processing of materials and communication. For instance, Si02 has been used to produce sample holders for microwave heating and substrates for electronic devices [2,3]. These applications generally require the material to withstand high temperatures under microwave irradiation. This indicates that microwave absorption capabilities of silicon dioxide at elevated temperatures are also important for its utilization.The microwave absorption capability of Si02 can be determined based on dielectric characterization (permittivity measurement) of the material at commonly used microwave frequencies, 915 and 2450 MHz, in a broad temperature range. To date, however, no detailed work on the dielectric properties (permittivity) of silicon dioxide at high temperatures has been reported. The present work is aimed to study the dielectric properties of silicon dioxide from room temperature to approximately 1000 °C at 915 and 2450 MHz. The results show that the permittivity of silicon dioxide has a strong temperature dependence above 500 °C, suggesting a substantial increase in its microwave absorption capability."

Jan 1, 2013