Search Documents

By Y. K. Rao

Relatively pure crystalline lead sulfate (PbSO4) can be produced by chemical vapor transport from an impure source such as the lead-acid battery paste or the roast-ore-leach-residue from a hy¬drometallurgical process-route. In a closed-reactor, transport of matter is induced by a tempera¬ture-gradient and the steady-state transfer rate can be calculated using the data on the standard free energies of formation for the species present and the pertinent binary diffusion coefficients. The present work focusses on chemical vapor transport in a tubular reactor (1.4-cm inner diameter x 10-cm long) with the source- and deposition-ends held at 850°C (T,) and 750°C (Td), respectively; PbC12(g) is the 'solvent' or 'transport agent' and NiSO4(s) placed in the source-zone -serves to maintain a sufficiently high S0,-potential such that the stability of the lead sulfate species is ensured. For the purposes of analysis, the gas-phase in the reactor is assumed to consist of eight species: H2O, PbC12, SO3, SO2. O2 HO, C12, and PbC14. The reaction between C12(g) and PbSO4(s) in the high-temperature source-zone produces PbCl2, SO2, and 02; four more reaction-equilibria in the same zone yield other species. In the low-temperature deposition-zone, reaction equilibrium involving PbC12, H2O, and SO, leads to the nucleation and growth of PbSO4 crystals; three other reaction-equilibria occur in this zone. By employing the virtual equilibrium state for the end-zones and coupling it to the Stefan-Maxwell diffusion equations for each of the gas species, the respective partial pressures for these, in the source- and deposition-zones, are computed at steady-state. From these data, the molar fluxes of PbCl2. PbCl4, and so forth, are determined. Allowing for the transport-enhancing effects of thermal convection, the net transport rate of lead (or PbSO4) is duly calculated for specified initial conditions. The predicted rates show very good agreement with measured rate data reported in the literature [ V. Plies, T. Kohlmann and R. Gruehn: Z. anorg. allg. Chem, 568, 62 (1989)

Jan 1, 1995

By Oscar Jaime Restrepo, Juan Camilo Restrepo, Jorge Ivan Tóbon

Portland cement is obtained by a conventional synthesis process from a mixture of limestone and clay at high temperature (1450 °C). This work reports the possibility to obtain cement silicates via alternative methods like Solution Combustion Synthesis (SCS), which optimize both time and temperature, and the consequences to energy efficiency and mitigation of CO2 emissions. The production of one ton of cement emits between 0.62 and 0.97 tons of CO2 into the atmosphere. In this process the CO2 emissions are between 21 and 59%. The combustion methods are chemical redox processes in which, at high temperature, a self-sustaining and fast wave is generated from using chemical precursors and organic fuels.

Jan 1, 2016

By Michael I. Morris

The U.S. Department of Energy's (DOE's) Transuranic and Mixed Waste Focus Area (TMFA), funded from fiscal year (FY) 1996 though FY 2002, was tasked with finding solutions for the mixed waste treatment problems of the DOE complex. During TMFA's initial technical baseline development process, three of the top four technology deficiencies identified were the need for amalgamation, stabilization, and separation/removal technologies for the treatment of mercury-contaminated mixed waste. The Mercury Working Group (HgWG), a selected group of representatives from DOE sites with significant mercury waste inventories, assisted TMFA in soliciting, identifying, initiating, and managing efforts to address these areas. Solicitations and contract awards were made to the private sector to demonstrate both the amalgamation and stabilization processes using actual mixed wastes. The goal was to develop separation and removal processes that will address DOE's needs. This paper discusses the technology selection process, development activities, and the accomplishments of TMF A through these various activities.

Jan 1, 2003

By Cesimiro Fabian

The crystallite size of copper electrodeposits was determined by X-Ray powder diffraction analysis using a General Area Detector Diffraction Solution (GADDS) diffractometer. Crystallite size was calculated for copper thin films which were deposited on a 316 stainless steel rotating cylinder electrode (RCE) in the presence and absence of additive ?A?. The crystallite size was calculated from a corrected full width at half maximum (FWHM) of the [110] peak profile using the Scherrer equation. The test of significant difference on crystallite size was derived using Kruskal-Wallis method. It was found that in the absence of the additive the median crystallite size was 426, which decreased to 364 in the presence of the additive. As the additive degraded, the crystallite size increased to a size similar to that observed in the absence of additive.

Jan 1, 2003

By T. C. Goel, A. Venna, R. G. Mendiratta

"Processing of ferrites has gained tremendous importance in recent times to meet the high performance demands on ferrites in keeping with the fast emerging· technologies. The quality of ferrite powders has strong influence on ·the performance of final device. Fabrication· of high performing ferrite components requires starting ferrite powders of precise stoichiometry, purity and microstructure. It is difficult to obtain these attributes by the conventional ceramic method. The key to obtaining quality powders lies in the· solution techniques. With this in view soft ferrites have been prepared by a wet chemical process, known as the citrate precursor method, which involves the formation of citrate complexes of the constituent cations. The advantages of this process are the ease of preparation and close control of composition, homogeneity, purity and particle size. Electrical and magnetic measurements on lithium ferrites have shown resistivity higher by more than two orders of magnitude compared to that observed for samples prepared by the conventional ceramic method, and low magnetic losses, making the ferrites specially suitable for high frequency applications.IntroductionProperties of ferrites are known to be sensitive to .their processing technique. A small deviation in the compositional stoichiometry of the ferrite affects its properties greatly. Soft ferrites such as Ni-Zn, Mn-Zn and Mg-Mn. are well known ferrites covering wide-ranging applications [1,2]. Lithiiim ferrites have also assumed technological importance for microwave applications and are potential substitutes for the expensive garnets [3]. Lithium ferrites are often doped with zinc to tailor the saturation magnetization required at high frequencies. Lithium and lithium-zinc ferrites, however, present difficulty to processing due to the volatile nature of both the cation components, namely Li and Zn. These ions are volatile at temperatures > 1000°C which makes their processing difficult. One of the main considerations of high frequency performance of ferrites is the high eddy current losses which prevent the interaction of the magnetic field with the ferrite component and hence impair device performance. These losses can be reduced by having a material of high resistivity. Electrical conductivity in lithium ferrite has been attributed to electron hopping [4] between the two vaience states of iron, Fe2+ <=> Fe3+, on octahedral sites. Maintaining the + 3 valence state of otahedral- Fe ions is thus a prerequisite for achieving high resistivity. The resistivity of ferrites is normally found to be low when processed by the conventional solid-state or the ceramic method [5]. This is attributed to (a) extensive ball-milling employed in the method to mix the component oxides results in non-stoichiometric compositions due to introduction of additional Fe ions on abrasion of steel balls during milling, (b) high processing temperatures involved which result in significant volatilization of Li and Zn ions creating thereby oxygen non-stoichiometry which results in reduction of Fe3 + to Fe2 +, (c) large and non-uniform grain sizes. In the present work, preparation of Li and Li-Zn ferrites by a non-conventional method known as a citrate precursor method [6, 7] which requires lower processing temperatures and duration is reported. The method gives stoichiometric compositions on account of homogeneous atomic-scale mixing of the constituent cations via the formation of metal-citrate complexes mixed in solution state. The method is also capable of giving small grain size which aids the oxidation ofFe2+ ions."

Jan 1, 2000

By S. Yuan

Oxygen ion conducting yttria-stabilized zirconia (YSZ) tube was used to remove oxygen from molten Cu at 1373K. Outer surface of the tube was in contact with the melt and the inner surface containing a thin layer of porous Ni-ZrO2 cermet electrode was in contact with a reducing gas. The migration of oxygen species (O2-) from the Cu melt through the YSZ tube is accompanied by an equal and opposite flux of electrons maintaining electroneutrality. Without applying an external EMF, the fluxes are maximized by short circuiting the melt with the cermet electrode. For efficient oxygen removal, the YSZ tube must be thin, contact resistances should be negligible, and the electrodes must be porous and cover the entire electrolyte surface for charge transfer. This refining process is environmentally sound, can use reducing gases such as H2, CH4 and CO without running the risk of increasing H or C content of the melt.

Jan 1, 1993

By David G. Dixon

A mathematical model is derived in dimensionless form which simulates the effluent concentration response of reagents from spent heaps under both fresh and recycled water rinsing. The model is based on dispersion from isochoric pathways distributed in length and cross-section, oriented normal to convection channels in ideal plug flow. The effects of heap height, rinsate flow, and initial reagent concentration are examined. It is shown that the rinsing cycle undergoes a distinct shift between fast and slow rinsing at a certain time depending on the amount of stagnant solution in the heap, and the distribution of dispersion pathways. Results of preliminary column rinsing tests on both agglomerated and unagglomerated ores are presented which partially validate the model.

Jan 1, 1994

By Murali Thirukkonda, Rahul Shah, Srinivas Tangrila, Shankar Rachakonda, Jan Kajuch, Arthur Gurson

"High-temperature superconductors have potential for a variety of applications such as power generators, superconducting magnets for mine sweepers or ship propulsion motors, and magnetic levitation transportation systems. Interest in the use of superconducting wires and tapes increased dramatically after the discovery of high-critical-temperature (high-Tc) oxide superconducting compounds, which offer operating temperatures above that of liquid nitrogen. Several techniques have been proposed to produce commercially viable high-Tc oxide based superconducting wires. One of the promising methods involves multi-pass powder-in-tube (PIT) wire drawing followed by rolling and heat treatment. This work focuses on the development of a numerical model to simulate the PIT drawing process for fabrication of long lengths of silver sheathed Bi-2212 superconducting wires. The finite element based model was used to predict densification of the oxide powder, wire drawing forces, and silver sheath thickness during drawing. A cap-type pressure dependent constitutive equation was implemented in the model to simulate the powder behavior. The model incorporated experimentally obtained material data for the silver and powder. Results indicate that powder densification is increased by decreasing the initial silver thickness and increasing the silver strength. Data from wire drawing experiments were used to verify model predictions. IntroductionSuperconducting wires and tapes can be used to carry large dc currents with no measurable loss due to resistivity. When used in superconducting magnets for power generators, motors, levitation devices, magnetic detectors, or energy storage devices, they could potentially result in significantly reduced energy losses. In the past, most prototypes were tested in liquid helium at 4.2K [1]. However, the necessity to provide liquid-helium cooling systems proved to be a serious limitation in commercialization. In 1986 high-critical-temperature (high-Tc) oxide superconductors were discovered [2], which could allow for higher operating temperatures above liquid nitrogen (77 K). Since then, both academia and industry have concentrated their efforts on the development of high-Tc oxide superconducting wires, tapes and coils. As yet, large scale fabrication of long lengths of these wires with the required current carrying capacity and mechanical properties remains an enormous challenge."

Jan 1, 1994

By J. Kevin Cotchen

The results of "submerged arc" electric furnace processing of a variety of materials is discussed with respect to the process and products, including the characteristics of the products (e.g. TCLP or Toxicity Characteristics Leaching Procedure). The materials melted include slags and wastes containing various metal oxides including copper, tin, lead, zinc, chrome, nickel and other associated elements. The findings of these tests are compared to those reported in the literature for other operations treating similar "wastes".

Jan 1, 1992

By F. H. Froes, O. N. Senkov, N. Srisukhumbowornchai

"Mechanical alloying (MA) and thermohydrogen processing (THP) approaches were used to synthesize amorphous or nanocrystalline powders of the titanium-aluminide-based alloys and composites. Fully dense samples with nanocrystalline and bimodal structures were produced from these powders by hot isostatic pressing. The stability of the microstructures during continuous heating at high temperatures was studied. Characterization techniques including X-ray diffraction, scanning and transmission electron microscopy, energy dispersive spectroscopy, and differential thermal analysis were used in this work.IntroductionAs performance demands increase, so do the demands for enhanced mechanical property combinations at reduced overall weight; and reduced weight can most efficiently be realized by the use of low-density metals with high specific strength, such as titanium alloys and titanium-aluminum intermetallics [l]. The TiAl-based alloys are attractive for high temperature applications, however, they exhibit poor ambient temperature ductility and fracture toughness [2-4]. Incremental improvements can be obtained using ingot metallurgy processing [1,2] but more substantial developments require ""far from equilibrium"" (FFE) synthesis [5-8] which allows development of novel constitutional and microstructural effects, leading to enhanced physical and mechanical properties. Improved ductility of titanium aluminide intermetallics can be achieved by disordering, grain refinement and deoxidation of the matrix, while good elevated temperature properties are achieved due to a dispersion of fine, thermodynamically stable, second phase particles.The approaches for producing nanocrystalline and amorphous TiAl-based alloys and composites used in this work included FFE powder metallurgy techniques such as rapid solidification, mechanical alloying and thermohydrogen processing. The rapid solidification (RS) technique allows extension of solubility limits, production of novel phases, and much more refined microstructures (down to nanostructure or even amorphous range) than is possible using the ingot metallurgy technique [9]. Mechanical alloying (MA) is a process in which heavy working of powder particles results in intimate alloying by repeated deformation, fracturing and welding. This process can produce greater departure from FFE than RS, leading to greater refinement effects; and additionally allows production of a dispersion of second phase particles [10]. Thermohydrogen processing involves hydrogen as a temporary alloying element in titanium to facilitate processes, refine microstructure, and improve final mechanical properties [11]; it was used in the present work to improve MA process. The combination of these three processes was expected to control the final microstructure even better than either process used alone."

Jan 1, 1998

By Xinghui Meng

The leaching behavior of platinum powder in .iodide solutions under oxygen pressure in an autoclave was investigated. Ammonium salts were added to the leaching solution at neutral pH as a key lixiviant for platinum. The effect of temperature, partial pressure of oxygen, concentration of iodide and of arttmonium salts on the dissolution rate of platinum was examined. Under experimental conditions, the leaching behavior of platinum powder exhibited a complex reaction mechanism. A precipitate was found during the leaching process and was identified to be platinum ammine iodide, Pt(NH3hI4. The dissolution rate was controlled by a series of chemical reactions, the equilibrium concentration of the platinum ammine iodide being responsible for the ultimate limit to the recovery.

Jan 1, 1996

By H. Senoh

For the purpose of clarifying the reason caused a drastic decrease of discharge capacity for MmNi3.6Mn0.4Al0.3Co0.7 electrode at relatively low temperatures, various factors influencing the charge-discharge processes were investigated in the temperature range of 25°C to -40°C. The charge efficiency obviously decreased at low temperatures less than 0°C due to a decrease in the rate of the charge-transfer reaction on the electrode surface. Moreover, both the rate of the hydrogen diffusion from the alloy bulk to surface and the rate of the charge-transfer reaction significantly influenced the high-rate dischargeability. The addition of Mo to MmNi3.6Mn0.4Al0.3Co0.7 alloy was found to be effective for improving the electrocatalytic activity, leading to the improvements of the charge efficiency and the high-rate dischargeability at relatively low temperatures.

Jan 1, 2002

By Md. Maniruzzaman

The quenching performance of a liquid quenchant can be controlled by controlling the agitation in the quench tank. Without agitation, a vapor layer or bubbles form at the hot part surface and the natural convention of the quenchant limit the heat extraction rate at the quenched part surface. Resistance to the heat extraction rate can be reduced by breaking the vapor layer or by inducing a turbulent convection at the part surface through agitation (Le. forced circulation of the quenchant). To determine the effects of agitation on the quench performance of a mineral oil based quenchant, the CHTE quench probe system was used with AISI4140 steel probe tip. Quenching performance of the oil is evaluated by computing the effective heat transfer coefficients of the steel probe as a function of surface temperature using Lumped Parameter Analysis. In addition, computational fluid dynamics (CFO) simulation of the quench tank with an impeller type agitator has been done to understand and predict the fluid flow pattern in the tank. CFO simulation also provides insights for determination of optimal location of the impeller and the quench probe tip. Keywords: CHTE Quench Probe, agitation, CFD simulation, liquid quenchant, 4140 steel

Jan 1, 2003

By J. P. Gu, C. Beckermann

"Melt convection and macrosegregation in casting of a large steel ingot is numerically simulated. The simulation is based on a previously developed model for multicomponent steel solidification with melt convection, and involves the solution of fully coupled conservation equations for the transport phenomena in the liquid, mush, and solid. Heat transfer in the mold and insulation materials, as well as the formation of a shrinkage cavity at the top are taken into account. The numerical results show the evolution of the temperature, melt velocity, and species concentration fields during solidification. The predicted variation of the macrosegregation of carbon and sulfur along the vertical centerline is compared with measurements from an industrial steel ingot that was sectioned and analyzed. Although generally good agreement is obtained, the neglect of sedimentation of free equiaxed grains prevents the prediction of the zone of negative macrosegregation observed in the lower part of the ingot. It is also shown that the inclusion of the shrinkage cavity at the top is important in obtaining good agreement between the predictions and measurements.IntroductionMacrosegregation in large steel ingots is one of the most well-known and now classical problems in the field of solidification and casting [1]. Commonly found macrosegregation patterns in steel ingots are a positively segregated zone at the top, negative segregation near the bottom in the equiaxed zone, inverse segregation near the ingot surface, V-segregates along the centerline, and A-segregates in the columnar zone [2, 3]. It is well established that the macroscopic transport of species leading to macrosegregation can occur by a variety of mechanisms, including thermally and solutally driven natural convection of the melt in the mushy zone, flow due to solidification contraction, and the sedimentation of free equiaxed crystals. Fredriksson and coworkers [ 4,5] provide recent overviews of the solidification transport phenomena and macrosegregation in ingot casting."

Jan 1, 1999

By Helfried Nafe

"For about a century thermodynamically absurd facts have been propagated in conjunction with the iron-carbon phase diagram. These facts concern fundamental relationships of chemical thermodynamics. Attention is turned here to the discussion of only one of the relevant aspects of the subject, i.e. the definition of the thermodynamic activity of the solute and its implications for the iron-carbon solution.IntroductionThe view on the iron-carbon solution is characterized by the assumption that the solute may appear in two different forms, i.e. graphite and cementite. Accordingly, two carbon solubilities are differentiated, on the one hand for graphite and, on the other hand, for cementite. As a consequence, two versions of the phase diagram exist simultaneously, the application of which depends on the prevailing conditions, (i) the so-called stable phase diagram with graphite as solute and (ii) the metastable one that is based on the cementite-in-iron solution. These diagrams are joined together in the double phase diagram that originates from Heyn [l ], with the first ideas mainly going back to Stansfield [2] and Charpy [3].Thermodynamically, the most inadequate implication of the Fe-C double phase diagram is that the carbon activity may take values larger than unity. With the standard state of the activity being that of the pure substance, i.e. the Raoultian one, such a value implies the nonsensical existence ofa state purer than pure. The explanation of this physical state, ifthere is any, vaguely refers to supersaturation and, in the wider sense, to the physico-chemical phenomenon of metastability. Other aspects of chemical thermodynamics are likewise involved. Therefore, the comprehensive investigation into the present subject requires more topics to be considered than only one separate issue. Not only should the criticism of the present view be in the focus but also the discussion of new ideas capable of reconciling the experimental facts, known about the F e-C system, with the fundaments of chemical thermodynamics. All this, however, cannot be provided here because of the limited space available. As a consequence, in what follows only a part of the whole problem is under scrutiny, i.e. the definition of the thermodynamic activity and its role for the interpretation ofrelevant experimental facts."

Jan 1, 2014

By Chang-Young Choi

Korea Zinc commenced zinc production in 1978 with a capacity of 50,000 tpa. Since then, continuous investments have been made and resulted in Korea Zinc now being the biggest zinc and lead producer in the world. In the course of increasing zinc production capacity, the company management realized that the company needed a lead smelter to prevent the solid waste disposal problems by treating the lead containing solid waste. This paper begins by briefly stating the objectives and the roles of the lead smelter at Onsan. It describes the QSL process and the TSL process, and further extends the description of the TSL process, through which harmless inert solid waste could be produced for secure final disposal. It is also mentioned that the TSL process plays an important role in the integration of zinc and lead production. Throughout the paper, a positive attitude in handling the environmental issues in the non-ferrous smelting industry is emphasized. Finally, a solution for the solid waste disposal problem in the zinc and lead industry is proposed, with which the environmental issues can be an opportunity rather than a crisis. The current operation at Onsan suggests the future direction of the non-ferrous smelting technology that all of the zinc and lead producers should pursue.

Jan 1, 2003

By Hong Liang-shi

Olivine lithium iron phosphate (LiFePO4) is considered as one of the most promising materials for lithium-ion secondary batteries because of its high theoretical capacity, low cost, good safety, benign environment and good cycle performance. In this paper, carbon-free and/or carbon-coated olivine lithium iron phosphate composite ultrafine powders were successfully synthesized from aqueous precursor solutions of (NH4)2Fe(SO4)2?6H2O, H3PO4 and LiOH?H2O by co-precipitation method. The obtained LiFePO4 or LiFePO4/C powders were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). Their electrochemical performance was investigated in terms of cycling behavior. As confirmed by X-ray diffraction and scanning electron microscope, the material obtained by co-precipitation within the temperature range of 60ºC to 100ºC and then followed by moderate heat treatment are a single-phase olivine LiFePO4with the particle size of about 300nm. An improved carbon-coated olivine LiFePO4/C material was prepared by adding conductive carbon materials, such as glucose, activated carbon and acetylene black, into the precursor. The carbon dispersed in the materials increases the electronic conductivity of LiFePO4/C composite, and consequently, leads to high rechargeable capacity of the material. The carbon-coated material with carbon amount of 7.64%wt obtained from glucose has the first discharge capacity of 150.3mAh/g at the rate of 0.1C and 129.3mAh/g at the rate of 1.0C, respectively. After cycled for 50 times, the capacity retention rate is 95.13% at the rate of 1.0C in the voltage range of 2.5 to 4.3 V vs. Li/Li+.

Jan 1, 2006

By Raymond E. Healy

Circuit samples from the HBMS concentrator were assayed for l5elements, and image analysis was done to determine the modal quantities, grain size distributions and liberations of the minerals. Material balancing was done on these data to determine distributions of the minerals in each concentrator stream. The ore was mined during the waning phase of mining and is diluted with backfilled copper smelter slag. The mill feed grades 1.0 wt% Cu and 1.8 wt% Zn. The slag silicate phases contain approximately 1.5 wt% Cu and 6.5 wt% Zn; therefore the Cu and Zn head grades due to chalcopyrite and sphalerite, are only 0.9 wt% Cu and 1.2 wt% Zn, respectively. The recovery of Cu in the Cu-concentrate (Cu-conc.) is only 77.5 %, whereas that of chalcopyrite is 89.2 %. Similarly, the recovery of Zn in the Zn-concentrate (Zn-conc.) is only 40.2 %, whereas that of sphalerite is 71.0 %. The slag accounts for approximately 60 % of the Cu, and 85 % of the Zn in the tailings. The main loss of chalcopyrite is as unliberated grains to the tailings, and the main loss of sphalerite is as free grains to the Cu-concentrate and as unliberated grains to the Cu-concentrate and tailings. Approximately 85 % of the chalcopyrite and sphalerite lost to the tailings. accounting for 8 % and 10 % of the respective minerals in the concentrator feed, occur as middling and sub-middling grains. Extremely fine regrinding would be required to liberate these minerals.

Jan 1, 1989

By Batric Pesic

Recovery of gold from refractory ores was studied by pressure oxidation as the method of ore pretreatment followed by bromination of oxidized residues. Three different ores were examined, Au-Ag, Au-Ag-Te, and Au-silver free ore. Pyrite was the major host mineral for gold in these ores. The effect of pressure oxidation parameters (temperature, pressure of oxygen, time, and pulp density) on subsequent bromination under standard conditions was examined. Bromination of residues produced under standard pressure oxidation conditions was examined as a function of: temperature, bromine and sodium bromide concentration, and time. Recovery of gold on activated carbon, from the pulp after bromination, was studied too. Recovery of gold from silver containing ores was lower (87-91%) than the recovery of gold from silver free gold ore (97%). In each studied case, the presence of activated carbon in the pulp further increased the recovery of gold.

Jan 1, 1992

By S. N. Ojha, Gouthama, R. K. Mandal

"Spray deposition processing of liquid immiscible alloys, based on AI-Pb and Cu-Pb systems have been investigated. Process variables have been optimized to generate uniform dispersion of ultrafine second phase particles in· the matrix of the primary phase. Mechanisms governing the microstructural evolution in this synthesis methodology are discussed. Results of the present investigation are used to demonstrate that rapid solidification of atomized droplets initially provides a high nucleation rate of the second phase during the liquid phase separation. The solid matrix phase nucleates at a later stage and grows with a high velocity enabling trapping of the dispersed phase. Subsequent alteration in the size and size distribution of the second phase is suggested to arise further during deposition of high velocity droplets. Possible reasons for this effect are brought out. Microstructural features of atomized powders and spray-deposits of these alloys are presented to support the present approach of synthesizing composites. IntroductionIn recent years, synthesis of advanced materials with metastable microstructures and ultra fine dispersion of second phase particles has led to the development of novel techniques of materials processing. The other requirement of such a processing methodology is to achieve near-net shape geometries in less number of processing steps. The solidification processing method via spray deposition route qualifies these criteria. This process primarily involves atomization of a melt by high energy gas jets into spray of droplets which are subsequently propelled by the kinetic energy of the gas towards a deposition substrate to build-up a thick high density preform. Although the concept of spray deposition was pioneered by Singer [1] in the early seventies, the fundamentals of the deposition process has been understood only recently [2-4]. Several benefits of spray deposition processing are by now well established [5,6]. Rapid solidification effects are inherent in spray deposition processing due to high heat exchange rate at the droplet-gas interface and also on the deposition surface by force convection. Since considerable heat extraction occurs from the atomized spray prior to droplet consolidation, a relatively low processing temperature is ensured in this process. As a result deleterious coarsening phenomenon can be minimized. In addition, controlled maneuvering of the substrate provides the capability of the process in producing disc, sheet or tube shape preforms of difficult to work materials in a single operation. A significant improvement in properties, resulting from microstructural homogeneity and refinement in grain size induced by spray deposition has been reported for several alloy systems [7,8]."

Jan 1, 1994