Search Documents

By Thomas E. Marshall

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) examined and characterized conditions at a majority of the underground stone mines in the United States. Observations at these mines revealed a limited degree of roof monitoring beyond visual inspection and sounding. When monitors are used, they typically require the miner to measure movement at the roof. If conditions are unstable, the miner may be in a hazardous situation while recording data. Based on this scenario, researchers surmised that a simple, inexpensive monitor with the capability of recording data at a distance from the mine roof would be a safer way to gain the information. Additionally, more widespread use of monitors could potentially lead to better understanding of roof movement in general. A monitor to meet this need was designed, tested, and subsequently improved as experience was gained in its' use at a number of underground stone mines. The Roof Monitoring Safety System (RMSS) can provide an initial indication of movement in roof beams. By understanding and measuring roof movement in underground mines, the potential for injuries and fatalities to mine workers From falls of ground can be reduced. Also, officials at a mine with a history of data are better prepared to make a decision on remedial actions in the event of ground falls. This paper will outline the evolution of the RMSS and how it can be used in a comprehensive pro-active ground control safety program. Also included is a cast history describing how the RMSS was used in an evaluation of the effectiveness of a mechanical impact scaling machine at an operating limestone mine.

Jan 1, 2000

By Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs. Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads. Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

Jan 1, 1999

By Alan D. Smith

[A standardized checklist in a questionnaire format, was established to investigate selected factors associated with coal nips roof falls, as derived from an intensive review of the literature. A plot study was undertaken to aspect and explore possible statistical relationships that may exist with these parameters. the Purposes of toe study were to: 1. Study in a systematic and empirical fashion selected parameters that may be capable of differentiating characteristics of roof falls; 2. Obtain some predictive indices cased on selected physical and management related variables so that predictions of future problems associated with mine roof falls can be completed, prior to its actual occurrence. Accomplishment of these goals should result in valuable guides to the mining engineer in scheduling exploration work and 4 determining economic feasibility of certain ground control and .lining pro and practices. The parameters associated with mine roof failure that where included in the questionnaire are: working section, county, spar., orientation degrees), pillar dimensions width, length), seam thickness, roof fall dimensions (length, width, surface area, volume), shape of fall (arch, dome, laminar), thickness of thinnest immediate layer, lithology of the first four i.e.-diate roof layers, thickness of h e first four immediate roof layers, type of initial support systems before failure, type of resupport system after failure, length and spacing of bolts in use before failure, length and spacing of bolts planned after allure, presence of .cater, time failure after It coal excavation, distance t3rest ace, physical operation during, time of coo failure, location of the roof fall entry failure occurred ence of sloughing of ribs before failure, and presence of floor heave condition before failure. The typical roof fall had an average roof spar of 20.3 feet, -06 feet depth o coal seam, occurred 136 feet from nearest face, coal seam thickness of inches, p--ar :width off 45 feet surface area D' roof fall 1151 ft2, mainly lamin- shaped, previously rat fore fall between good to very good, little floor heave presence, usually cracks before the fall about 40 percent of reported cases, shales in most of the immediate layers, and usually located in an entry or intersection. in addition, multiple linear regression techniques were employed in the testing process of 18 major research hypotheses in a search for relationships among the various parameters studied of which were found to be significant, once corrected for multiple comparisons.]

Jan 1, 1984

By David H. Tang

Similar massive pillar failures were observed in two underground coal mines with different configurations of mine workings and overburden depths. Finite element models were used to analyze the causes and mechanisms of the pillar failure. The results of the analyses confirms the underground observation. For Case No. 1 the failure of coal pillar is mainly caused by a combined effect of smaller coal pillars under a large overburden and the interaction of multiple seam mining. For Case No. 2, the pillar failure was initiated by the weak roof rock but the ultimate pillar failure was caused by the splitting of pillars into very small size.

Jan 1, 1984

By S. S. Peng

This paper presents a convenient way for the preliminary design of the shield supports. The locus equations which are applicable for all kids of shield supports are derived. These equations facilitate the statics analysis of the shields. An indirect method in determining the coefficient of friction, the external toads and their locations are also developed.

Jan 1, 1982

By Gexin Sun

This paper presents the physical modelling results of subsurface fracture development associated with longwall mining operations and an application of image processing techniques to interpretion of the results. Physical modelling results have been obtained by employing a large sand and plaster model loaded purely by gravity as a means of fracturing the subsurface strata above the longwall excavation. The results have shown fracture development and crack propagation as a longwall face advances and demonstrated that the strength of stratified rocks, the presence and position of a weak band-, and the extraction thickness, have significant effects upon the overall fracture patterns above the excavation. Binary images of fracture patterns were scanned from the black and white photographs of the tested models using an image analyser coupled to a video camera. These images were manipulated by a custom written C program which allows the images to be processed in both vertical and horizontal direction. The images were filtered to quantitatively differentiate between vertical and horizontal fracture intensities. The vertical fracture intensity is particularly important as vertical fractures are considered to provide the main avenues for surface and subsurface water inflow into the excavation. The use of the image analysis techniques has shown a promising improvement in image enhancement and in model results interpretation in a quantitative manner. The numerical nature of the image analysis results will allow further statistical comparison with other modelling techniques to be undertaken and significantly increase the scope for use of the modelling technique results.

Jan 1, 1992

By Gregory M. Molinda

An investigation was conducted to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure, and suggestions for controlling this problem are presented. Hazardous roof conditions identified in a number of mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52% of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath a number of valleys in the form of bedding-plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomenon, was found at mining depths as great as 300 ft. In situ horizontal stress measurements in a mine beneath a valley and the adjacent hillsides confirmed valley stress re1ief. Underground mapping showed that roof falls in excess of 100 ft in length and up to 25 ft high closely aligned with the valley axis. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress. Thickness of cover, valley shape, and the orientation of the valley relative to the maximum regional horizontal stress all influence the "valley effect" on roof stability.

Jan 1, 1990

By Leo L. Van Sambeek

Specification of properly sized pillars to support the overburden is one of the most challenging aspects of salt mine design. Interest in salt pillar design is heightened by the recent flooding of the Retsof salt mine, water inflows to the K2 potash mine, and closing of the Belle Isle salt mine because of ground control problems. A series of numerical modeling analyses show that a simple pillar design equation for salt pillars adequately reproduces results of extensive modeling efforts. The paper describes (1) the basis for the pillar design equation, (2) equation verification by comparison with numerical modeling results, and (3) equation validation by comparison with measurements and observations of salt pillar behavior.

Jan 1, 1997

By Xiaolin Wu

Most coal bump occurrences in the U.S. are directly related to mining operations under strong roofs. An understanding of the behavior of bridging or cantilevering strong roofs over working longwall faces is a key to a safe and productive longwall operation. In this paper, an attempt has been made to study the behavior of strong roof beds using the elastic beam theories. Four structural models are formulated to simulate the locations of strong roofs and their distinct weighting stages. For each model, analytical solutions for the deflection, bending moment, stress, and the strain energy stored in both the coal scam and the strong roof are obtained. Solutions for the critical spans, which are controlled by the caveability of the strong roof beds, are developed. The effects of rocks' differing elastic moduli, under tension and compression, on the actual flexural rigidity, and stress redistribution are analyzed.

Jan 1, 1993

By Duk-Won Park

A vast majority of the operating longwall sections use shield-type face supports to provide ground control in the United States. As a co-operative research program between the University of Alabama (UA) and Jim Walter Resources, Inc.(JWR), a joint research program is underway to study interaction of shields with surrounding rock masses. A series of analyses on the response of shields are performed using monitored data at a longwall face in a deep coal mine. In this paper, various effects of parameters, such as leg pressure, setting load, developing load, maximum loading rate, pressure in capsule, and convergence between canopy and base, are discussed and recommended as stability indices. A microcomputer program is being developed for instantaneous interpretation of the shield monitored data, and for giving warnings of potential problems. The preliminary results define the effects of the setting load, developing load, and rate of developing load or leg closure rate. The objective of the study is to understand the shield characteristics and their interaction with surrounding strata in real time, then develop a reliable program for maintaining longwall stability.

Jan 1, 1992

By Tim Ross

J. M. Huber Corporation's Quincey Mine. an underground limestone mine located near Quincy. Illinois, has operated successfully and safely for many years utilizing roof bolts on a very limited basis. Over the years, the mine had experienced several rool falls that did not result in injury to personnel. Nearly all of the roof falls were limited to the first 2 feet of the massive limestone roof. Investigation of the falls indicated the major contributing factor to these roof falls was a randomly occuring thin. horizontal clay layer in the immediate roof. Over time, separation would occur at the clay layer. causing the root to sag. and eventually causing the root to fail. J. M. Huber Corporation contracted with NSA Engineering. Inc. to assist in a study to determine the effectiveness of Ground Penetrating Radar (GPR ) for locating these potential root fall areas so that mitigating action could he taken prior to roof failure. Multiple tests were conducted in areas of known roof conditions. GPR accurately predicted the existence or absence of root separation up to 1.5 meters into the immediate roof for 100 % of the known lest site conditions. As a consequence of this successful studs, J. M. Huber Corporation has used GPR to evaluate roof conditions at both its Quince and Marble Hill Mines.

Jan 1, 2002

By Thomas Barczak

Longwall shields provide essential ground control in Iongwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of¬the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (I ) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield's capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

Jan 1, 2002

By R. Karl Zipf

Multiple seam mining interactions caused by full extraction mining, whether due to undermining or overmining, frequently involve tensile failure of the affected mine roof. The adverse ground control conditions may prevent mining for both safety and economic reasons. Prior researchers have identified the geometric, geologic and mining factors controlling multiple seam mining interactions. This numerical study examines the mechanics of these interactions using a modeling procedure that 1) incorporates the essential constitutive behavior of the rock such as strain- softening of the intact rock and shear and tensile failure along bedding planes and 2) captures the geologic variability of the rock especially the layering of weak and strong rocks and weak bedding planes. Specifically, the numerical study considered the effect of vertical stress, interburden thickness, and the immediate roof quality of the affected seam in both undermining and overmining situations. The models show that for overburden-to-interburden thickness (OBAB) ratios of less than 5, interactions do not occur, and that for OBAB more than 50, extreme interaction is a certainty. In between, the possibility of an interaction was found to depend on gob width-to-interburden thickness ratio, site specific geology and horizontal stress to rock strength ratio in addition to the OBIIB ratio. The models also showed that horizontal stress was profoundly altered well above or below a full extraction area and that these changes are likely to influence the success or failure of multiple seam mining. The role of horizontal stress in multiple seam mining interactions has received little attention in prior investigations. Four factors control the mechanics of multiple seam mining interactions: 1. vertical stress concentration 2. horizontal stress concentration 3. stress re-direction 4. bedding plane slip bands A combination of vertical and horizontal stress increase and high stress gradients in the vicinity of full extraction areas re-orients principal stresses into a very unfavorable direction. This seemingly small stress re-orientation has a profound adverse effect on bedded rock.

Jan 1, 2005

By S. Y. Liu

Based on the underground measurements, physical model test of simulated materials in the laboratory and finite element analysis, this paper demonstrates the pattern and process of roof fall over the tip-to-face area in the fully mechanized coalfaces. The main factors that affect the stability of the immediate roof are thoroughly studied including the fracture position and tilt angle of the main roof, the tensile strength (Rt) and cohesive force (c) of the immediate roof, and type and resistance of the powered support. Based on these factors, this paper proposes the basic process of immediate roof breakage a. follows: As the longwall farm advances, the main roof breaks and then rotates. A tensile fracture zone will be formed in the immediate roof under the fracture line of the main roof. A caving zone (plastic zone) will be formed in unsupported area between coalface and canopy tip. If these two zones overlap the immediate roof will be completely unstable. Under this condition, powered support will have difficulties lo control the rod. Therefore it is necessary to study the process of immediate roof breakage and look for effective methods for controlling the roof.

Jan 1, 1990

By Klaus-Dieter Beck

RAG American Coal Holding, Inc. affiliates operate two longwall mines in the Pittsburg seam in Pennsylvania, the Cumberland mine and the Emerald mine. A unique situation in longwall operation occurred at these mines as the mining activities reached the property boundary between the two mines. The retreat direction in the longwall panel in Cumberland mine is West-to-East while in Emerald mine, it is East-to-West. This unique condition required an adequate design for barrier pillar between the two mines to minimizing the mutual effects of longwall retreat when both longwall faces met and an adequate roof control plan for gateroads. Field studies that involved mainly roof-to-floor convergence monitoring were conducted to assess the effectiveness of the employed barrier pillar in isolating the mutual effect of longwall retreat. Three-dimensional finite element numerical modeling was used to evaluate the gateroad roof and pillar stability. The modeling was conducted such that it duplicated the actual mining process as realistically as possible. The modeling results predicted that the employed barrier pillar and the roof control plan would ensure stable gateroad systems in both mines during and after the two longwall faces met. The prediction was confirmed because mining operations in the two longwall panels were completed without any noticeable ground control problems.

Jan 1, 2004

By S. M. Hsiung

A model (support selection model) for the selection of suitable types of powered supports under various geological conditions is proposed. This model is developed by evaluating the support, performance under different roof conditions at longwall faces in terms of five controlling parameters: (1) roof Falls, (2) front abutment pressure, (3) Face convergences, (4) gob materials entering into working area, and (5) roof caving line. This model suggests that more than one type of powered support. may be used under the same roof condition and the best selection should he based on the magnitude of suitability index of each support- type. The development and application of suitability index arcs discussed. Fourteen panels in seven coal seams are discussed in the paper to illustrate the applicability and effectiveness of this model. A roof classification system at longwall faces developed specifically for the construction of the selection model is also discussed. A simple example fur determining roof classification index is given.

Jan 1, 1988

By Venkata S. Vutukuri

Compressive strength of cylindrical specimens of a model material and sandstone with various diameter/height (d/h) ratios was determined in unconfined compression tests. It was observed that the compressive strength increases with increase in d/h ratio. Triaxial compression tests were also conducted on the specimens of the same materials with a d/h ratio of about 0.47. It was observed that the axial stress at failure increases with increase in confining pressure. A very interesting correlation was found between the effect of d/h ratio on compressive strength in unconfined compression tests and the effect of confining pressure on axial stress at failure in triaxial tests. The relationships between d/h ratio and confining pressure, s3 in MPa are:- For model material - s3 = -0.95 + 1.7957*(d/h) 0.7883. For sandstone - s- (-0.4554 + 0.9888* (d/h) 1.0355. The correlation coefficients for these equations are 0.9997 and 1. These equations are valid for d/h ratios of up to 10.

Jan 1, 1993

By Rao Pothini

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support. This paper describes in detail the testing methods, data analysis results obtained, and recommended changes.

Jan 1, 1992

By Anthony T. Iannacchione

Underground bituminous coal mining is a large and significant industry within the Commonwealth of Pennsylvania, and it has a legacy of environmental consequence. For example, in 2008, 13.5 acres (5.5 hectares) of land were undermined by longwall mining every day. Laws and regulations have been promulgated requiring companies involved in this industry to remedy mining damage caused to homes, businesses, and land; replace impaired water supplies; and repair impacts to streams and wetlands. The regulations and technical standards set by the Pennsylvania Department of Environmental Protection (PA DEP) have been put in place to assure that coal operations comply with ACT 54 of the Bituminous Mine Subsidence & Land Conservation Act and other related legislation. These regulations and standards require operations to address impacts when a mining permit is submitted and as permits are modified and extended. One of the special provisions of ACT 54 is the requirement by the PA DEP to produce an assessment of the surface impacts of mining every five years. The University of Pittsburgh was contracted by the PA DEP to perform the 3rd assessment, which spanned from August 21, 2003, to August 20, 2008. This paper details the findings related to surface structure undermined during this period. A total of 3,735 structures were tracked. Four-hundred-fiftysix reported effects were found, and each required additional information and analysis. The majority of the reported effects were associated with eight longwall mines. Characteristics of the structures were analyzed and discussed, with special attention to those with reported effects. The number of undamaged and reportedly damaged structures (i.e., dwelling, barn, commercial building, etc.) undermined during the assessment period were listed. Lastly, the resolution status and type of resolution were analyzed for all structure reported effects.

Jan 1, 2011

By Vincent Scovazzo

Cost-effective underground mine configurations have been designed in highly fractured rock masses where the stone possesses a high material strength. A limestone mine in the eastern United States is used to demonstrate procedures for the geotechnical design of one such operation. The mine discussed is located in both limbs and the axis of a recumbent fold that fractured the rock mass. In a highly fractured rock mass, where the host rock has high strength, a design can be developed to alleviate intact rock failure. This is possible because in most cases as the stress levels needed for intact failures are approached, the stresses are quickly dissipated due to movement along discontinuities, which represent planes of weakness. As a result most underground failures in highly fractured rock are due to sliding or toppling. Even when intact rock fails in a highly fractured rock mass, it is the movement along an existing joint or other weakness plane that often initiates or causes this failure. It is therefore important to obtain the characteristics of weakness planes that are the discontinuities within the mass. The required information on weakness planes, geology, and strength of materials is discussed and recommendations for obtaining this information are presented. A discussion is provided on failure modes and the use of developed information for their evaluation. The impact on geotechnical design is demonstrated through pillar sizing procedures; however, this approach can also be applied to mine roof and pillar foundations.

Jan 1, 2002