Search Documents

By Jonathan Duncan, Tim Burgess, William Kendall, Jens Lange

"Steel wire mesh is the accepted standard for roof and rib skin control at most coal mines in the United States. Wire mesh is delivered to the mine in bundles that are heavy and awkward to handle. The large size, stiffness, and weight of the wire mesh can present a safety hazard in transporting underground and storing on the roof bolter. Installing wire mesh on the roof and ribs with the roof bolter can be a challenge as well.Synthetic mesh is lighter than wire mesh and can be folded and rolled into a safe, manageable size. A single synthetic mesh roll large enough to cover the roof and ribs in a deep cut can be safely handled by two men. The roof bolter is designed to carry and dispense the roll as it advances and installs primary roof support, resulting in a single pass roof and rib ground control solution. This paper focuses on the design and implementation of the roof bolter synthetic mesh handling system developed by J. H. Fletcher & Co., Huesker, Inc., and Oxbow Mining.INTRODUCTIONRoof and rib skin control in some coal mines has been an issue since mining first began. Roof and rib skin problems vary from mine to mine. The type of roof rock material exposed after mining; the mine atmosphere; and stresses from depth of cover, over mining, and/or undermining are some of the variables that can contribute to roof skin problems from mine to mine.Potential roof and rib skin problems can be time dependent as well. Some mines have roof skin rock, sometimes called draw rock, that falls when drilling the hole for the roof bolt as the initial roof support is installed. Some roof skins are more stable but can fail over time. The failure of roof skin can even be between properly installed roof bolts with roof plates (Figure 1).Mines have most commonly used a wire mesh that comes in individual panels anywhere from 5 ft x 5 ft (1.5 m x 1.5 m) all the way up to 5 ft x 16 ft (1.5 m x 4.9 m) in size. They are typically constructed of 8- or 9-gauge wire welded on a 4 in (102 mm) square pattern. A 5 ft x 16 ft (1.5 m x 4.9 m) panel weighs approximately 35 lbs (16 kg). These steel wire mesh panels can make it a difficult and sometimes dangerous task to deliver them from the surface to the roof bolter and then store on the machine. Manipulating the mesh panels from the storage area on the machine to the final installation position on the roof or rib can also be a daunting task (Figure 2)."

Jan 1, 2010

By Peter Cain

The Phalen Colliery in the Sydney Coalfield is extracting the 2.6 m thick Phalen Seam by the panel and pillar longwall retreat method. Abandoned workings occur in the Harbour Seam 140 m above and overlie the Phalen Colliery. Parts of these workings are flooded, and pose a number of questions relating to the safety of operations in the Phalen Colliery. In order to answer some of these questions, the Cape Breton Development Corporation re-entered an abandoned non-flooded roadway in the Harbour Seam directly above a retreat panel in the Phalen Seam to allow the deployment of instrumentation to monitor interaction effects. Fifteen monitoring sites, each 4.5 m apart, were installed in the 5 East Top Level after it had been re-entered and made safe. Each monitoring station included a vibrating wire strain gauge piezometer and a potentiometric extensometer. The piezometers were attached to rock bolts anchored into the floor and were connected by a flexible standpipe to a constant head apparatus. Variations in hydraulic head due to subsidence were monitored to determine subsidence. The extensometer units were mounted on rock bolts anchored into the floor of the roadway beneath the ribside and monitored ground strains. The instrumentation was capable of remote reading in the event that access to the site was restricted after installation. This paper describes the instrumentation, the installation programme, and some preliminary results.

Jan 1, 1993

By Kyle A. Perry

Pillar design formulae have existed for decades, and the guidelines for design stability factors are generally accepted by regulatory agencies and broadly used within the coal industry. Nearly all design pillar formulae are based on geometrical parameters of pillars resulting from empirical investigations, with primary focus on the pillar width-to-height (W/H) ratio and associated shaping constants from regression. The most widely used modern pillar design formula in the coal industry, the Mark- Bieniawski equation, also adheres to this principle. Common practice when applying Mark-Bieniawski equation is to use a coal compressive strength of 900 psi. This reduces the design equation to sole dependence upon geometry. However, recent studies have shown that pillar strength is highly dependent on roof and floor properties, particularly the interfaces between the roof-pillar and pillar-floor. This study utilized numerical modeling using FLAC3D to evaluate the relative effects of varying roof and floor interface and mechanical properties. The results confirm that pillar strength is significantly influenced by the properties of the coal pillar interfaces with roof and floor. The mechanical properties of the roof and floor material have only a minor impact on pillar strength when compared with interface effects. These results were used to formulate design recommendations for existing pillar design methods.

Jan 1, 2013

By Keith A. Heasley, Christopher R. Newman

"Originally developed in 1993, LaModel has aided mining engineers and researchers alike in improving the design and safety of underground single- and multiple-seam mining operations (Heasley, 1998). Through the years (Heasley, 2011), the use and capabilities of the LaModel program have grown immensely while adapting to ground control concerns and problems within the mining industry. Presently, MSHA specifically mentions the use of LaModel for the analysis of, “complex non-typical roof control plans,” defined as either room-and-pillar retreat mining greater than 1000 feet, bump- or bounce-prone mines, or other criteria considered unusual by the District Manager (Stricklin, 2013).With an ever increasing number of users and an increase in available solution options and complex analyses, there is now a significant demand for better education and training in the practical application and detailed analysis using LaModel. This paper presents the development of an electronic user’s manual and comprehensive online training course created in an open online learning environment in order to better inform and train industry professionals as well as engineering students and new users. The development of both the user’s manual and online training course will ultimately increase the ground control design effectiveness of mining engineers, leading to safer and more productive mine designs.INTRODUCTIONOver the past 20 years, mining engineers and researchers have used the LaModel program for improving the design and safety of single- and multiple-seam mining operations. LaModel uses a laminated, displacement-discontinuity, boundary-element method which simplifies the overburden into a stack of frictionless homogeneous laminations and limits the detailed analysis to the seam itself. This approach is fundamentally simpler than either finite-element, finite-difference, or discrete-element approaches; and, therefore, the program provides a significant reduction in computational time and efficiently calculates the displacements, stresses, pillar safety factors, multiple-seam interactions, subsidence, etc. for thin-bedded deposits such as coal, salt, potash, limestone, etc. (Heasley and Salamon, 1996; Heasley and Agioutantis, 2001). The laminated overburden model in LaModel is different than previous homogeneous elastic formulations and more realistically represents the natural flexibilities of the stratified sedimentary overburden typically associated with coal seams (Heasley, 2008)."

Jan 1, 2015

By Peng Zhang

In a recent research effort, a laminated overburden loading model (as implemented in LaModel3.0 was compared with the results of ARMPS 2010, and the laminated overburden model was found to more accurately classify a ARMPS database of 52 deep cover case histories by a factor of 60% versus 54%. However, the LaModel analysis of each case study required several days to complete, as compared to a requirement of only several minutes for each ARMPS analysis. In the research presented in this paper, a computer code (ARMPS-LAM) has been developed to effectively implement the laminated overburden model into the ARMPS program. This program takes the basic ARMPS geometric input for defining the mining plan and loading condition and then automatically develops, runs, and analyzes a full LaModel analysis of the mining geometry to output the stability factor on the Active Mining Zone(AMZ), all without further user input. The present laboratory version of ARMPS-LAM can be run in batch mode; therefore, the ARMPS 2010 database of 645case histories can be analyzed very quickly. In an initial logistic regression analysis of this database, the ARMPS-LAM program was seen to be slightly more accurate than ARMPS 2010 by a factor of 71% versus 63%.

Jan 1, 2013

By Ihsan Berk Tulu, Michael Sloan, Ted Klemetti, Michael M. Murphy, Gabriel S. Esterhuizen, Jame Sumner

"In this paper, the advantage of using numerical models with the strength reduction method (SRM) to evaluate entry stability in complex multiple-seam conditions is demonstrated. A coal mine under variable topography from the central Appalachian region is used as a case study. At this mine, unexpected roof conditions were encountered during development below previously mined panels. Stress mapping and observation of ground conditions were used to quantify the success of entry support systems in three room-andpillar panels. Numerical model analyses were initially conducted to estimate the stresses induced by the multiple-seam mining at the locations of the affected entries. The SRM was used to quantify the stability factor of the supported roof of the entries at selected locations. The SRM-calculated stability factors were compared with observations made during the site visits, and the results demonstrate that the SRM adequately identifies the unexpected roof conditions in this complex case. It is concluded that the SRM can be used to effectively evaluate the likely success of roof supports and the stability condition of entries in coal mines.INTRODUCTIONSince the introduction of roof bolts in the coal mines during the late 1940s and 1950s, roof bolts promised to dramatically reduce roof fall accidents (Mark, 2002). However, ground falls still remain a significant factor in underground coal mine injuries and fatalities. In 2013, ground falls accounted for 4 of the 14 fatalities and 166 of the 1577 reported lost-time injuries in underground coal mines (MSHA, 2015).The design of appropriate support systems requires the understanding of: 1) the variable nature of the rock mass, 2) the performance and characteristics of the roof support, 3) the interaction between the rock mass and the installed support system, and 4) the in-situ and mine-induced stress distribution around the excavation. Over the past 25 years, multiple design approaches have been used in coal mine ground control. The approaches include empirical mechanistic methods, empirical statistical analysis, rules of thumb, and numerical methods (Hebblewhite 2006). In the U.S., Analysis of Roof Bolt Systems (ARBS) can be given as an example of an empirical method. ARBS uses relatively simple equations to calculate the intensity of support provided by a roof bolt system and compares it with a suggested ARBS value (Mark et al., 2001). The suggested ARBS design equation is derived from an analysis of 100 case histories. The ARBS design equation is dependent on two parameters: depth of cover and Coal Mine Roof Rating (CMRR). More recently, a probabilistic design approach was developed by Canbulat and van der Merwe (2009) in South Africa. In this method, the variability of the rock mass, the mining geometry, and support characteristics are included in the analytical models. The major advantages of these two methods are: 1) they can be applied rapidly and easily, 2) complex rock mass/ roof support interaction mechanisms are represented with simple equations, and 3) they are supported by large databases. However, both methods generally ignore mining-induced stress distribution, details of the roof support system, details of the geological setting, and the interaction between the support system and the rock mass."

Jan 1, 2015

By Yuanfei Chen, Jianfeng Zha

"China is the largest producer and consumer of coal in the world. The mining-induced surface subsidence has bad influences on the surface and structures above the surface. In order to minimize disasters, removal, reinforcement, or maintenance structures are often adopted. In the application of maintenance methods, it is necessary to carry out dynamic surface subsidence prediction to choose maintenance methods, optimize maintenance time, and evaluate the amounts of work. Time series methods and influence function methods are common for dynamic surface subsidence prediction, but the former is difficult to consider with underground mining conditions, and the latter has low prediction precision. Therefore, this paper develops a dynamic subsidence prediction model aided by field-measured data and realizes the model programming. The model could achieve high-precision prediction of dynamic surface deformation through optimizing the parameters in time by using field-measured data of surface subsidence. The research results of engineering cases show that, with the method of dynamic prediction, the standard error can be controlled in the range of 5%, greatly improving the accuracy of dynamic prediction of mining subsidence, which provides strong technical support for the maintenance and management of structures. INTRODUCTION With the rapid economic development and continued industrialization process, the demand for energy is growing in China. Today, China is one of the largest coal, oil, and gas consumers in the world. Coal consumption accounts for 47.7% of the total consumption in the world (Tian, 2016). In order to meet the demand for coal resources in the process of modernization, more and more coal mines carry out coal mining under villages, buildings, highways, and bodies of water. The mining-induced overlying strata and surface subsidence have bad effects on surface and on various structures (such as buildings, railways, highways, high-tension transmission lines) and could even cause various disasters (Williams et al., 1998; Bell et al., 2000; Doyle et al., 2002). Generally, methods, such as removal, reinforcement, or maintenance are taken to eliminate the adverse impacts (Kraatz, 1984; Bell and Genske, 2001; Wang, 1989). When reinforcement or maintenance is selected to remove bad effects, the proper maintenance methods must be chosen. In addition, maintenance time, as well as an evaluation of time it will take to do the work are necessary to predict the surface subsidence with high precision."

Jan 1, 2017

By Kevin J. Ma, John Stankus

"In order to access remote reserve areas, some U.S. coal mines have to maintain aged underground entries for a great distance. However, high humidity, warm temperature, and time dependent deterioration can cause progressive roof deterioration and unexpected roof falls can, pose a great challenge to ground control engineers. With an active belt structure in place and limited space, re-bolting becomes very costly, less effective, and, sometimes, impractical and unfeasible. To gain long-term entry stability and serviceability, operators typically rehabilitate the aged belt entries by installing standing steel set supports. In the last several years, Keystone Mining Services, LLC, (KMS) has assisted many coal mines with their belt entry rehabilitation projects, evaluated the ground condition of various aged belt entries, and designed different standing steel set support systems. This paper presents a case study of a large-scale roof fall that occurred at an aged belt entry in a mine located in an eastern coalfield, analyzes root causes of excessive deformation of square sets that were installed in an adjacent entry, evaluates the adequacy of an existing rehabilitation square set, and develops remedial recommendations for future rehabilitation practice. Based on the case study, the paper outlines design guidelines for rehabilitation steel sets that include field evaluation, engineering considerations, design assumptions, steel structural analysis, and field installation quality control. INTRODUCTION With gradual depletion of shallow coal reserves, some underground coal mines have to maintain long-term entries (belt, track, return airway, etc.) for a great distance in order to access remote coal reserve areas. However, due to high humidity, warm temperature, and aging in the belt entry, roof strata weathering and pillar degradation become more and more severe. Progressive roof deterioration poses a great challenge to ground control engineers. Pillar rib sloughs at certain locations, entry width increases in some areas, immediate roof sags, immediate roof rock falls out between bolts, existing bolts lose functionality due to corrosion, cutters develop deeper in corners, and strata separation develops deeper up into the main roof. As a result, unexpected roof falls occur in a random manner resulting in loss of production, damage of belt structure, and even injuries to underground personnel."

Jan 1, 2017

By Pinnaduwa H. S. W. Kulatilake

A new formulation is given to conduct a probabilistic block theory analysis. A new computer code (BTAC) has been developed to perform both deterministic and probabilistic block theory analyses. The variability of the discontinuity orientation and shear strength is incorporated in the probabilistic block theory analysis. Discontinuity orientation is treated as a bivariate random variable including the correlation that exists between the dip angle and dip direction. BTAC code was applied to perform both deterministic and probabilistic block theory analyses for a part of an open pit mine in the U.S. Needed geological and geotechnical data for the analyses were obtained from field and laboratory investigations. The variability of the discontinuity orientations resulted in important differences between the probabilistic and deterministic block theory analyses results. The results confirmed that the design value selected for the Maximum Safe Slope Angle (MSSA) for a particular region in the open pit mine based on the deterministic block theory analysis can be on the unsafe side. In summary, the results showed clearly the superiority of probabilistic block theory analysis over the deterministic block theory analysis in obtaining additional important information with respect to designing rock slopes.

Jan 1, 2014

By Elizabeth Holley, Meriel Young, Gabriel Walton

"The coal mine roof rating (CMRR) was developed by Chris Mark and Greg Molinda to bridge the gap between geological variation in underground coal mines and engineering design. The CMRR accounts for the compressive strength of the immediate roof, the shear strength and intensity of any discontinuities present, and the moisture sensitivity of the immediate roof. The CMRR has been widely used and validated in Eastern US coal mines, but it has seen limited application in the Western US.This study focuses on roof behavior at a Western coal mine. Mine A shows significant lateral geological variation, along with localized faulting and a laterally extensive sandstone channel network. The CMRR is not used to predict roof instability at the mine.It is, therefore, hypothesized that there are other factors that are correlated with roof instability in underground coal mines that could potentially also be included in the CMRR.This hypothesis was tested by collecting 30 CMRR measurements at Mine A. At each measurement location, a binary record of the roof condition (stable or unstable) was made along with parameters, such as depth of cover, thought to also correlate with roof stability. A statistical analysis of the data was performed to determine the parameters in addition to those included in the CMRR, which can be correlated to roof stability.INTRODUCTION AND BACKGROUNDRoof fall is one of the greatest hazards facing underground coal miners (Barczak et al., 2000). In 2017, 91 lost-time injuries occurred due to roof fall in US underground coal mines. A further 48 roof falls occurred with no lost days (MSHA, 2018).The coal mine roof rating (CMRR) classification was developed by Molinda and Mark (1994) to quantify the geological description of mine roof into a single value that could indicate mine roof stability and be used in engineering design. It is widely used in the Eastern US as an input for the analysis of longwall pillar stability (ALPS) in underground coal mines. It provides an excellent start; however, it is arguably not fully comprehensive, nor is it widely used in the Western US."

Jan 1, 2018

By Kot F. Unrug

Since the introduction of longwall systems, the prediction of roof behavior and support requirements have become the major issue referring directly to safety as well as productivity. In more recent times, and especially in the USA where longwalls are exclusively equipped with costly hydraulic self- propelled support systems, a decision whether a longwall is applicable in a given condition, and when so, what kind of equipment should be selected, is of primary importance. There are numerous examples where lack of experience, and subsequently wrong selection of supports or winning machines, resulted in considerable losses. It should be emphasized that careful studies of prevailing geological and mining conditions, especially in a new area, are required to assure a successful operation. An evaluation of the conditions can be carried out in different ways utilizing such methods as: - Theoretical approach. applicable when geological conditions comply with the theoretical assumptions. - Empirical relationship which gives satisfactory results where the coefficients could be adequately determined. - Structural geological studies which must be undertaken in all cases, since the frequency of fractures and their orientation have a prevailing influence on roof behavior. - Scale model study on equivalent material for determination of failure conditions in the roof and mechanism of movement (flow) of broken rock matter. Coefficients for empirical formulas can be determined by these types of studies, as can boundary limits for mathematical modeling. - Mathematical modeling, e.g., finite element analysis. - Measurements and observations taken underground during the development period end utilization of experience for previous longwall panels in the area. Usually it is the most practical method where mining and geological conditions are comparable. An application of me or more of the above approaches remains to be a matter of judgement for particular conditions, however, the utilization of a practical experience, when available, is usually the safest way for planning a successful longwall operation.

Jan 1, 1982

By Robert M. Cox

The successful application of the science of rock mechanics to the practical problems of coal mine design requires the acquisition and reduction to useable form of large amounts of field and laboratory data, and the construction and analyses of numerous geostructural models containing a wide variety of geometric and physical strength variables. Typically, the rime constraints placed on a new mine design project coupled with the inherent complexities of a good rock mechanics study combine to limit the applications of rock mechanics to the most rudimentary level. To facilitate a better application of rock mechanics to mine design problems, an interactive software package has been developed for use on a graphic mini-computer system that serves to aid the engineer in the timely and efficient analyses of rock mechanics data and geostructural models. The first phase of the rock mechanics package solicits the input of the raw geologic and rock strength data, analyzes and arranges this data in a logical manner, produces complete listings and statisitical summaries of the various rock properties, and stores the data on magnetic tapes and disks to serve as a future Rock Mechanics Data Base. The second phase of the software package provides for the analyses of a variety of geostructural models using a wide variety of geometric variables coupled with the rock strength data stored in the Rock Mechanics Data Base. This software package allows for the evaluation of numerous geostructural mine models for the design and selection of mine roof support and pillar systems (see Table l).

Jan 1, 1982

By Darin Cotton, Tim Burgess, Tim Martin

"As the leading US supplier of roof control drills, J. H. Fletcher and Company® has encountered an extensive set of roof strata challenges and has overcome various drilling issues by varying machine parameters and working with customers and tool manufacturers to develop solutions. Every mine wants to drill and install roof bolts as fast as possible with maximum safety at the lowest possible installation cost for their conditions. In most circumstances, the intuitive method of higher speeds and pressures can actually have a detrimental effect on the roof drill safety and performance.This paper will outline recent tests carried out at several different coal mines in the Eastern United States. The tests focused on optimizing the drilling parameters of feed pressure, feed rate, rotation speed, and drill torque.The drill feed, rotation speed, and rotation torque, as well as the type of bit selected, have a definite impact on the performance of the roof drill including drilling speed, safety, and tool life. The drilling process can be improved while also improving operator safety and reducing bolt installation costs by maintaining the appropriate roof drill settings for the specific strata conditions.The advantages of improving the drilling process includes increased bit life, increased drill steel life, reduced hanging drill steels, reduced clogging of the vacuum system, decreased whipping drill steel potential, reduced noise generation, and increased cutting size which reduces fine dust generation and dust collection system servicing.INTRODUCTIONIn recent times, the economic pressures that coal producers are facing have created an increased emphasis on controlling operating costs. Several coal operators have pointed out their dissatisfaction with low bit life, and there is a renewed interest in improving tool life and machine performance as part of an overall cost control strategy. Operators are looking for ways to reduce tooling cost, maintenance costs, and drill downtime without decreasing drill performance. This renewed interest in reducing operating costs, along with the ongoing desire to improve safety, created a perfect environment to take a fresh look at the existing fleet of machines to see what could be accomplished. The goal was to take a practical approach to reviewing machine parameters to determine what changes could be made. The emphasis was on changes that would be feasible to roll out to an entire fleet of machines in a short period of time with minimal capital expenditure. The thought process was that significant improvements could be made by simply tuning up the machine parameters to provide a more efficient and safer bolting process."

Jan 1, 2015

By Ihsan Berk Tulu, Keith A. Heasley, Chris Mark

"The Analysis of Retreat l\.fining Pillar Stability (ARJ\1PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover. To this end, the National Institute for Occupational Safety and Health (NIOSH) and the West Virginia University (WVU) l\.fining Engineering Department have been working together to improve both the ARJ\1PS and the Lal\.fodel programs.This paper compares and analyzes the overburden loads calculated by ARJ\1PS 2002, the new ARJ\1PS 2010, and the Lal\.fodel program with regard to the retreat pillar line, the gob, and the barrier pillars. The analysis shows a number of distinct differences between the ARJ\1PS and Lal\.fodel loading distributions. Ultimately, the programs, with their distinctive load distributions, are used to analyze a database of 52 deep cover pillar retreat case studies, and the ability of each program to discriminate between successful and unsuccessful retreat pillar plans is evaluated.INTRODUCTIONThe Analysis of Retreat l\.fining Pillar Stability (ARJ\.f PS) and the Lal\.fodel programs have been used successfully in the U.S. for designing safe pillar recovery operations for many years. However, the recent Crandall Canyon l\.fine collapse showed that further research is required to improve the pillar design for recovery under deep cover.Pillar recovery accounts for less than 10% of the coal produced from underground coal mines; however, in the period between 1989 and 1996, it accounted for more than 25% of all ground fatalities (l\.fark et al., 2003). In the past 15 years, the safety of retreat mining operations has greatly improved. l\.fark (2009) explains three steps promoted by l\1SHA and NIOSH for safer pillar recovery:1) Global stability through proper pillar design2) Local stability through proper roof support3) Worker safety through proper section managementThe ARJ\1PS and Lal\.fodel (Heasley, 1998) programs have been playing an important role in guiding mine operators in designing pillars to ensure the global stability of a retreat panel."

Jan 1, 2010

By Chris Kelly

The Monroe County Quarry is an open pit granite quarry located near the town of Bolingbroke. Monroe County. Georgia. The quarry has been in continuous operation for approximately 10 years. The quarry covers approximately 27 acres and has an annual production rate of 1.0 million tons. On the morning of April 26. 2000 a sudden rapid highwall failure occurred at the west end of the north wall of the quarry pit. The failure occurred approximately one hour after a three inch-wide crack was observed in an access road located at the crest of the highwall. No indications of failure had been observed prior to the development of the crack. The active mining area had been at the base of the failed area. The pit was successfully evacuated prior to the failure and there were no losses of either personnel or equipment. The amount of failed material was estimated to be in excess of two million tons. In order to ensure a safe working environment at the quarry a slope monitoring program was established in the area of the failure. The program consisted of using an EDM survey instrument to periodically measure the location of survey prisms installed at carious points on the north wall. The locations of the prisms were recorded over several months and changes in location were analyzed in order to identify and characterize the movement of the failed mass. The results of the analysis provided a basis for recommendations regarding access to various areas of the quarry. This paper discusses the factors contributing to the failure, the method of post-failure slope monitoring, anti the interpretation of the monitoring data.

Jan 1, 2002

By Tim Miller, Michael M. Murphy, John L. Ellenberger, Gabriel S. Esterhuizen

"A limestone mine in Ohio has had instability problems that have led to massive roof falls extending to the surface. This study focuses on the role that weak, moisture-sensitive floor has in the instability issues. Previous NIOSH research related to this subject did not include analysis for weak floor or weak bands and recommended that when such issues arise they should be investigated further using a more advanced analysis. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to demonstrate the effect that a weak floor has on roof and pillar stability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface.IntroductionMassive roof falls extending to the surface at a limestone mine in Ohio have been studied collaboratively by the National Institute for Occupational Safety and Health (NIOSH) and the mine owners. This paper provides a summary of the sequence of events leading to observed instability and presents a numerical modeling analysis that investigates the role a weak floor can have on roof and pillar stability.This study builds upon previous NIOSH research in underground limestone mines undertaken by way of a survey that analyzed performance of pillars in 34 different stone mines in the Eastern and Midwestern United States between 2005 and 2009 (Esterhuizen et al., 2011). This survey led to the development of underground stone mine pillar design guidelines based upon a “stability factor” for the pillar system. The factor is compared to operational experience to determine ranges of values that are typical of stable pillar systems. A software package titled Stone Mine Pillar Design (S-Pillar) was developed for easy application of these guidelines (Esterhuizen and Murphy, 2011).Weak floor in the present case study departs significantly from cases included in the previous NIOSH research, in that none of the 34 study mines had weak floor issues. Moreover, this case study is the first in which a weak floor has been monitored routinely as roof falls are occurring. A detailed report on the observations and measurements taken at the mine has been published (Murphy et al., 2015). The previous observations led to the conclusion that although there were weak bands in the pillar, the weak floor was the significant defect that led to the instability issues. The pillars were initially mined in 2004, approximately 10 years before the instability issues began to occur. The objective of this study is to use numerical models to analyze a variety of floor strengths and the impact of moisture content to find the critical point at which the floor becomes unstable, leading to long-term instability issues."

Jan 1, 2015

By Stephen C. Tadolini, Anthony T. Iannacchione

"Coal burst represented a major hazard for some U.S. mining operations. This paper provides an historical review of the coal burst hazards, identifies the fundamental geological factors associated with these events, and discusses mechanisms that can be used to avoid their occurrences. Coal burst are not common in most underground mines. Their occurrence almost always has such dramatic consequences to a mining operation that changes in practice are required. Fundamental factors influencing coal burst events include strong strata, abnormal strata caving, elevated stresses, critical size pillars and the lack of sufficiently sized barrier pillars during extraction. These factors interact to produce excessive stress, seismic shock and loss of confinement mechanisms. Over the 90 years of dealing with these hazards, many novel prevention controls have been developed including novel mine designs and extraction sequences, most of which are site specific in their application. Without an accurate assessment of the fundamental factors that influence coal burst and knowledge of their mechanisms of occurrence, control techniques may be misapplied and risk inadequately mitigated. INTRODUCTIONCoal burst1are violent failures of ribs, roof or floor in underground mines. They are known to occur in complex ways and often under unique sets of conditions. This has made them extremely difficult to anticipate and control. Assessing coal burst risk requires engineers, managers, and safety professionals to recognize the fundamental factors responsible for these events. This helps practitioners recognize the hazard potential and understand the context in which various controls and barriers should be used. Only then can coal burst events be anticipated andappropriate mitigation techniques deployed.Over the last 90 years, a few coal burst events have been anticipated but most have eluded prediction. The authors examined the historical record (Appendix A) and determined that an inadequate understanding of the initiating geologic factors and their associated mechanisms of occurrence have contributed to the poor predictive capability. The historic record also indicates that control techniques have typically been site specific in their application."

Jan 1, 2015

By Wen H. Su

Multiple seam mining and its associated problems are very serious in Southern West Virginia where poor planning or lack of knowledge in seam interaction often results in complete loss of coal properties. Several measures have been proposed to alleviate the interaction prob¬lems under various multiple seam conditions, but few of them are spec¬ific in terms of mining plan. Two parallel approaches are adopted for this paper. One is field investigation which consists mainly of mine site visits and gathering of data. The other is the two-dimensional finite element simulation of mine workings using the data gathered as input. Two typical cases which represent the past and present multi¬ple seam mining practice in West Virginia were investigated. Much attention is focused on the interaction problems experienced and the important parameters controlling interaction. Several key parameters controlling interaction in multiple seam mining were analyzed. Proper mining plans, by which the interaction problems can be minimized, are proposed for the individual cases after a better understanding of the interaction mechanism was realized through finite element analyses.

Jan 1, 1984

By J. Nielen van der Merwe

During the process of pillar extraction at the Welgedacht Colliery, an unexpected pillar collapse resulted in the entrapment of equipment. The area was visited soon after the event to evaluate the stability of the area for the purposes of extracting the equipment. It was found that the area had stabilised sufficiently to allow work without undue risk to the safety of workers. The equipment was reclaimed successfully. A subsequent investigation into the reasons for the collapse was conducted. It entailed detailed underground and surface subsidence observations and numerical modeling. It was found that none of the perceived negative factors that were present at the time could result in pillar loads that were sufficient to cause the collapse. It was concluded that the local pillar strengths were less than the nationally used value and that they were possibly further reduced by aging.

Jan 1, 1999

By Khaled M. Mohamed, Michael M. Murphy, Ted M. Klemetti, Heather E. Lawson

"The design of rib support systems in U.S. coal mines is based primarily on local practices and experience. A better understanding of current rib support practices in U.S. coal mines is crucial for developing a sound engineering rib support design tool.The objective of this paper is to analyze the current practices of rib control in US coal mines. Twenty (20) underground coal mines were studied representing various coal basins, coal seams, geology, loading conditions, and rib control strategies.The key findings are: (1) any rib design guideline or tool should take into account external rib support as well as internal bolting; (2) rib bolts on their own cannot contain rib spall, especially in soft ribs subjected to significant load—external rib control devices such as mesh are required in such cases to contain rib sloughing; (3) the majority of the studied mines follow the overburden depth and entry height thresholds recommended by the Program Information Bulletin (PIB) 11-29; (4) potential rib instability occurred when certain geological features prevailed—these include draw slate and/or bone coal near the rib/roof line, claystone partings, and soft coal bench overlain by rock strata; (5) 47% of the studied rib spall was classified as blocky—this could indicate a high potential of rib hazards; and (6) rib injury rates of the studied mines for the last three years emphasize the need for more rib control management for mines operating at overburden depths between 500 ft and 1,000 ft.IntroductionEfforts to improve the stability of underground mine ribs have continued for decades. These efforts by mining professionals around the world persisted throughout the 1990s and 2000s as well, though much of this work focused on rib support methodology and selection of proper support for a specific location. Despite these efforts, it is unfortunate that there has been a continual occurrence of rib-related fatalities in underground coal mines. While overall improvements in rib safety have been achieved, the average fatality rate is still about 1.3 fatalities per year over the last 18 years (Jones, 2014).To manage and control the rib hazard, rib support is used in U.S. coal mines. The current rib support methods for U.S. mines fall into two main categories: rib control based on intrinsic support systems and those based on external support systems. Intrinsic or rib-bolt support requires a roof bolting machine that can install a bolt fixture into the rib. Furthermore, the appropriate level of support needed to control the ribs with an intrinsic-based support system as well as the design parameters for those support systems for various mine conditions have not been established in U.S. coal mines. Furthermore, surface control systems are often an integral part of these support systems and must be considered in the system design."

Jan 1, 2015