Search Documents

By V. G. Papangelakis, G. P. Demopoulos

The high temperature (180-200 OC ) pressure oxidation (02 - HzSO4) process for the recovery of gold from refractory concentrates (FeS2/FeA8S) is simulated with the aid of a computer model. The model centers on the continuous operation of a multi-stage horizontal autoclave. In particular the effects of key process parameters controlling the autogenous operation of the autoclave are critically examined. The building elements of the model are (i) the continuous particle size distribution function of the concentrate, (ii) the residence time distribution function of the slurry and (iii) the shrinking core kinetics. Conversion is calculated on the basis of the segregated flow model. For the calculation of the particle size distribution at the exit of each compartment the population balance model is employed. The effects of feed rate, feed preheating, cooling, autoclave configuration and rate limiting regime (chemical reaction vs. gas-liquid mass transfer) on the autogenous steady state operation are discussed. Finally optimum reactor design and operation criteria are indicated.

Jan 1, 1990

By Kalliat T. Valsaraj, Louis J. Thibodeaux

A mathematical model is described for the transfer of hydrophobic compounds from aqueous to an immiscible organic phase using fine bubble aeration; the process otherwise known as "solvent sublation" an adsorptive bubble separation process. The limitations of the model are explored by simulating experimental results both for a batch scale process and a continuous process. The qualitative predictions of the model with respect to the influence of the organic layer (mineral oil) are tested by performing experiments using chloroform and 2,3,6-trichloroanisole as hydrophobic compounds in the aqueous phase. The continuous process is seen to be limited by the requirements of fine bubble generation and the ratio of influent feed rate to air flow rate.

Jan 1, 1989

By Sizhe Tan

An open pit mining operation can be considered as a production system with at least two products: ore and overburden (waste). A primary mine planning task is to schedule the production of ore and waste over its life span subject to several technical and economic constraints to maximize some objective such as the overall profit from the operation. Two major constraints are (i) the feasible combinations of ore and waste productions and (ii) the limiting function for ore production as a function of mine life. The task in scheduling production and stripping ratio (ratio of waste to ore production) is to find an ore production curve below the upper bound function of ore production, and a stripping ratio curve within the feasible domain of ore production and overburden removal while maximizing the defined objective. Zn this paper, feasibility of developing computerized optimization models to perform such a scheduling process is explored. Two optimization models are proposed for the task. In the first approach, a linear programming (LP) model is employed and in the second, a dynamic programming procedure (DP) is outlined. In these models, in addition to the consideration of the two major constraints mentioned earlier, various other contributing factors such as interest rate, equipment purchase cost and installation schedule, operating cost, and equipment idle cost are incorporated. An example is provided to illustrate the LP model application.

Jan 1, 1992

By J. R. Woolsey, B. G. Noakes

A prototype remote placer drill (RPD) has been designed and successfully tested in the offshore gold district of Nome, AK. The RPD system is unique in its design and in the cooperative support that was provided during its development by industry, academia and government. The RPD was conceived as a low-cost, rapid drill sampling system for the reconnaissance of marine precious metal placer deposits. The drill functions as a counter- f lush system. It incorporates a dual wall casing and a rotating percussion bit driven by way of a drill rod through the central eductor casing by a heavy duty pneumatic rock drill. The cost of drill sampling in the exploration of marine precious metal placers has traditionally been high due to the technical difficulties imposed by the environment and the remoteness of the sampling target. The objective was to reduce capital and operating costs of a drilling program through the development of a portable system incorporating drill compoments having a high power-weight ratio that could be deployed from work vessels of opportunity. A principal design requirement was to operate the system remotely from the sea floor with only flexible connections to the surface. This includes cable for deployment and retrieval and hoses for air supply and sample recovery, thus making the drill system semi-independent of the vessel's sea-induced motion. The prototype RPD underwent full operational test off Nome, AK in late summer 1988. It was deployed from the landing door of a modified LCT vessel, and rigged for a single pass of 5 m (16.5 ft). More than 50 holes were drilled in a wide variety of bottom materials typical of the off shore Nome submerged beach placers. The prototype RPD proved to be an overall success, recovering representative samples throughout the section in all but the heavy boulder ground. Compared with a conventional drill system on board that was assigned to a production drilling system, the RPD was capable of reliably sampling moderate ground less than 6 m (20 ft) in thickness, using a smaller crew and operating in higher sea conditions.

Jan 1, 1991

By H. Lind

Mining in Estonian oil shale deposit mainly takes place in the Ordovician, Keila-Kukruse aquifer. The aquifer is affected by mining and is fully dried out around the working mine areas (Perens and Savitski, 2008). The groundwater level is decreased down to 30 m, to the mine floor elevation using about 30 pumping stations (Lind, 2005). The pumping rate is very high - depending on the season, ranging from 10 up to 40 m3 per ton of produced oil shale (Reinsalu et al., 2006). The Estonian oil Shale Company mined 15.5 million tons of oil shale in 2007 (Source: Estonian Oil Shale Company). In order to predict the effects, and avoid the social and environmental impacts, there is a need to continuously monitor the situation and run software simulations aiming at decreasing the pumping rate. This becomes even more important since the environmental taxes on usage of groundwater resources increase every year. Therefore, it is necessary to monitor groundwater level and quality, and develop a groundwater model for the overview of the situation during mine operations and also for a number of years after mine closure.

Jan 1, 2008

By Dennis V. D’Andrea, Peter G. Chamberlain, James J. Olson, William C. Larson

Blasts designed for in situ copper leaching must produce adequate fragmentation and permeability for successful leaching. Copper recovery depends to a large extent on the particle size distribution created by the blast, the permeability in the blast- fractured zone, and the ability to maintain solution flow with a minimum amount of channeling. This paper presents the results of Bureau of Mines experiments where core drilling was used before and after blasting to establish the degree of fragmentation. Data are presented from tests at the Sierrita mine of Duval Corp., and also from tests at the Emerald Isle mine of El Paso Mining and Milling Co. Copper recovery is predicted from fragment size distribution data using a computer model. Data from several blasts are used to show how predicted copper recovery is related to powder factor.

Jan 1, 1977

By Wei Bin, Liu Zhe, Liping Xiao, Jichi Bai

The Acid Mine Drainage has characteristics of low pH, high concentrations of heavy metal ions, such as Fe2+, Mn2+, Cu2+ and Zn2+. In this paper, the composite particles that consisted of bentonite and steel slags were used to dispose the Acid Mine Drainage. Bentonite is the mineral materials and can adsorb heavy metal ions excellently. The steel slags are alkaline and industrial solid waste for the treatment of the Acid Mine Drainage. The main influencing factors, such as adsorbent dosages, shaking rates, concentrations of heavy metal ions, temperatures, adsorption time and pH value were studied by the static experiment. Increasing the adsorbent dosages and the concentrations of the heavy metal ions, speeding up the shaking rates, raising the temperatures, extending the adsorption time and improving pH would improve the removal efficiencies of heavy metal ions. Through considering the removal efficiencies and the treatment costs, the optimum reaction conditions for the four kinds of heavy metal ions were obtained. The adsorbent dosage 21 mg/L, the rotational speed 120 r / min, the temperature 25?, adsorption time 100 min and the initial wastewater pH 7. The four kinds of heavy metal ions existed independently in the simulated mine wastewater. The highest initial concentrations of Fe2+, Mn2+, Cu2+ and Zn2+ were 150 mg/L, 100 mg/L, 170 mg/L and 140 mg/L respectively. The removal rates were 93.42%, 92.64%, 93.86% and 95.17% respectively. The determination of the particles’ SEM-EDS Microscopic characterization showed the composite particles could play a part in neutralizing, absorbing and the chemical precipitation. The acidity decreased notably and the heavy metal ions of Fe2+, Mn2+, Cu2+ and Zn2+were adsorbed and precipitated effectively. The research results can extend the practical engineering application of the composite particles.

Jan 1, 2017

By Thomas Fenner

Surface and underground mining operations are often hindered by unknown tunnels and slopes and the precise locations of adjacent workings. Mine safety and planning are adversely affected especially in previously undermined areas where historical records are incomplete or nonexistent. The results of several ground penetrating radar (GPR) studies for the detection of known mine tunnels in underground coal, salt and gold mines are presented. A case study to locate unknown, abandoned mine workings at a surface gold mine successfully located all workings to a depth of 11 m (36 ft).

Jan 1, 1996

By R. R. Rollins

Conventional methods of controlling abandoned mine fires include: loading out, inundation, fire barriers, flushing, and surface sealing. This paper describes a proposed fire-control technique utilizing a new explosive fragmentation method. An impervious barrier is created by using explosive energy and strategic emplacement in boreholes drilled from the surface. Blast round design, average fragment size, and impermeability of the fragmentation barrier are discussed. This barrier, created by the blasted floor rock, could also be used to fill in the open space in abandoned mines for subsidence prevention or control.

Jan 1, 1989

By C. Rutter, S. Nelson

"Climax Molybdenum Company’s Henderson Mine, owned by Freeport McMoRan Inc., is a panel caving molybdenum mine located 69 km west of Denver, Colorado. The mine utilizes long interconnected ore passes as part of the ore flow system. Knowing the approximate level of ore in these ore passes is beneficial for preventing increased dust concentrations in various production areas, as well as scheduling truck loading operations. Level monitoring has been achieved by using a strain gauge placed on the steel structure of the truck chute, an amplifier and a Programmable Logic Controller. This paper explains the concepts and limitations associated with using strain gauges for ore pass monitoring as well as applying proactive dust prevention and level monitoring interfaces. INTRODUCTION The Henderson Mine, located 69 km west of Denver, Colorado, is an underground molybdenum mine which uses a panel caving process to produce 18,000 tonnes per day currently. This process involves dumping ore down a series of interconnected ore passes leading to truck chutes. Trucks use these chutes to load ore and deliver this ore to an underground crusher. If ore is pulled below the lowest intercept of these ore passes, a ventilation pressure imbalance occurs which generates a large amount of dust on the levels where ore is being loaded into the tops of the ore pass. When a dust event occurs, work must be stopped until the dust settles. Once the dust settles the ore passes must be filled significantly before trucks can start pulling from the corresponding chute. This downtime and unplanned work due to dust can be avoided if the approximate ore pass levels are known. Strain gauges have been installed and tested on a truck chute at the Henderson Mine and the results of these tests have led to a series of concepts in using strain gauges to monitor ore pass levels. This paper explores these concepts and corresponding limitations and explains how the application of ore pass monitoring can be achieved with the use of strain gauges. Ore Pass and Ventilation Pressure Imbalance Overview At the Henderson Mine, there are typically two or four ore passes in different drifts that combine into one bin to create an ore pass complex as shown in Figure 1. When the level of ore is at or below the 7210 intercept (I82W), four drifts have a ventilation connection to each other and the 7655 exhaust level. A “piston effect” is created each time a bucket of muck is dumped down the ore pass. Figure 2 illustrates this phenomenon: as the loader in 621 dumps a bucket down the ore pass, the muck pushes the air in the ore pass down the 82A leg and back up the 82B leg which generates a large amount of dust. The bin regulators on 7655 cannot be opened enough to allow for this surge of air to be relieved onto the exhaust level and the dust ends up exhausting into the 625 and 627 drifts."

Jan 1, 2018

By B. K. Parekh, W. M. Goldberger

Sludge obtained during the production of magnesium (Mg) from molten MgCl2 by electrolysis contains entrapped magnesium particles. The sludge containing the magnesium particles is a friable, continuous matrix of frozen salts that may also contain some oxides and impurities. Due to the high reactivity of magnesium metal with water, a dry process was developed to recover magnesium metal from the sludge. The process utilizes mineral-processing unit operations. The steps include selective comminution, screening, attritioning and tabling. Recovery of the high-grade (>90%) metal was in the 70% range. The novel process was also successfully applied to a magnesium-alloy for the recovery of metal from the sludges.

Jan 1, 1997

By William J. Francart, Edward J. Miller

The utilization of computer based monitoring systems for fire detection in underground coal mines has grown significantly in the past seven years. In 1984, an annual MSHA survey identified a total of 38 systems being used in U.S. underground coal mines, while a 1990 survey indicated the number has risen to 112. The applications for mine monitoring have also changed according to the annual surveys. From April 24 to June 21, 1990, investigations were conducted by personnel of the Ventilation Division, Pittsburgh Health Technology Center, in cooperation with Coal Mine Safety and Health, concerning the installation and operation of Atmospheric Monitoring Systems in underground coal mines. These investigations were conducted to gather information concerning the ability of the AMS to detect fires and heatings, false and nuisance alarm frequencies, information related to system maintenance, and information related to employee training on system operations. This paper addresses current applications of the systems, fire and heating identification rates, application of systems in dieselized coal mines, system maintenance, and employee training requirements. While deficiencies were identified in some applications, results of the studies and survey indicate the use of atmospheric monitoring systems can be effective in identifying mine fires and heatings.

Jan 1, 1991

By Jerzy Iskra, Wlodzimierz Sikora

INTRODUCTION The effect of stress concentration in coal seams leads to a sudden release in the form of rock bursts. This effect is controlled along many lines, but the most efficient methods consist in preventing the accumulation of energy in the seam or in the roof. The over- burden weight resulting from mining is the main cause of excessive stresses in a seam. An additional weighting of roof takes place due to formation of abutment loads. The accumulation of energy in the roof takes place where thick sandstone beds occur in overburden strata. An essential problem is to watch, with appropriate measurements, the stress of coal and roof rocks, and to conclude, on this basis, the degree of rock burst hazard. The methods for determining the stresses in a coal seam are quite well developed at present. Let me mention here the seismoacoustic methods, or borehole overcoring measurement methods. On the other hand, an examination of the state of stress in the roof rocks is almost impossible at the actual stage of development of the measuring technique. Hence, the model of stresses in roof was analyzed and determined theoretically. Based on this model, a technology for roof fracturing was developed which aims at destressing rock masses in a planned way. The essentials of the fracturing method consist of a controlled breaking of sandstone roof beds in order to: - prevent the excessive weight on the pillar - prevent a spontaneous breaking of roof beds at a limiting state followed by sudden energy release. High pressure fluid infusion is used to release buildup of stresses. THEORETICAL AND RESEARCH BASES According to the tests carried out by A. Kidybinski by the method of finite elements, isobars of stresses occurring in the roof over the working face are shown in [Fig. 1]. The results indicate: - the highest values of compressive stresses occur in the roof directly over the seam, at a distance of about 5 m ahead of the working face - at a distance of about 22 m above the seam there is a line of transition of compressive stresses into tensile - within the tested roof area, the highest tensile stresses occur at a vertical distance of 35 m, and at a horizontal distance of 20 m from the line of the working face. H. Gil (1) determined the pres- sure initiating the fracture of roof rocks by the formula: [ ] On the basis of results of analysis of isobars, and of the initiation of failure stress formula (1), isobars may be designed for a given roof class. Assuming for sandstones the Poisson ratio equal 0.3, a field of failure stresses presented in [Fig. 2] is obtained. In this figure it can be seen in which areas the effects of sandstone breakage may be obtained with the operation of a determined hydraulic pressure. To use formula (I), the knowledge of Rr is still necessary. This value may be determined in two ways: - taking a sample and testing it in the laboratory, if there is access to roof rocks in the existing openings, - drilling boreholes in the roof from surface and examination of the rock mass by using hydraulic breaking, if there is no access to roof rocks.

Jan 1, 1982

By P. A. Tuzinski, L. J. Dahl, N. R. Adamson, S. E. Brink, R. L. Blake

The US Department of the Interior, Bureau of Mines is developing a process to selectively extract manganese from oxide ores as part of its in situ mining research program. The Bureau is conducting site characterization studies of two manganiferous iron-formation deposits. These studies include: drill core, regional stratigraphic relationships from the existing geologic database, ore body geometry, geologic structure, hydrologic conditions, accessibility of ore minerals to leach fluid, surface subsidence potential and data collected from laboratory leaching experiments. This information is being used to evaluate the technical, environmental and economic feasibility of in situ mining of manganese for these two deposits. This paper will focus on the stratigraphy, mineralogy, ore textures, fractures, permeability and porosity as they relate to in situ mining.

Jan 1, 1994

By W. Trask

The state of the art in crawler transporters for loads to 3 kt (3300 st) is sufficiently advanced to allow compilation of job cost figures showing the economics of tracked vehicle use under a wide variety of circumstances. Initial costs, cost per ton of capacity, and operational and maintenance expenses are presented. Data is derived from participation by the Neil F. Lampson Co. in more than 3 Mt - km (2.05 million st - mile) of crawler operation during the past 16 years. The effects of economics on future design trends will be examined with particular reference to versatility, portability, and capacity.

Jan 1, 1987

By O. Fernandez, M. Vesely

Abrasive grinding, leading to ultrafine product and "critical size" material buildup inside the mill, is proposed as the cause of high power consumption and low capacity in many fully autogenous grinding processes. Addition of steel balls (hence, semiautogenous grinding) or pebble removal and separate crushing have been used, with different efficiencies, to overcome the problem. Information and data for the conceptual analysis, basic design, and operation of a pebble crusher at the Los Bronces semiautogenous grinding plant is presented along with data showing a production increase of 1000 t/d (1100 stpd) and significant operating costs savings.

Jan 1, 1987

By D. E. Ranta, Ora H. Rostad

Ore reserve estimation, from the earliest "quick and dirty" estimates made at the first consideration of a possible project down to periodic revisions of detailed estimates made during the life of a mine, should take into account many geologic and allied factors in order to obtain results that will provide proper guidance for necessary economic decisions. Factors include: sample collection and analysis, character of the vein and associated wall- rock, mineralogy, pre and post mine oxidation effects, core loss, sample correlation, internal vein structure, wallrock controls, geologic factors affecting dilution in mining and interrelated mining and milling problems.

Jan 1, 1992

By D. R. Tweeton, L. W. Lake

A modified push-pull field test and a computer model of cation exchange were developed to aid in evaluating cation exchange parameters prior to in situ mining. Reliable determination of these parameters is essential when modeling restoration of ground-water quality. The field test involves a much larger volume and much less disturbance to the ore sample than is feasible with laboratory measurements. This test can be per¬formed in two or three weeks. It is relatively inexpensive, requiring one injection-production well and two or more wells for collecting samples of leach solution. The use of the model in interpreting test results is illustrated with field data from an in situ uranium mine. Much of the research was performed by the University of Texas at Austin and was partially funded by the US Bureau of Mines.

Jan 1, 1987

By G. Papantonopoulos

Natural stones are extensively used for construction purposes since the dawn of human civilization, due to their unique aesthetical and technical characteristics. Their production and consumption has been continuously increasing over the past twenty years worldwide at an annual rate of 8.8%. European countries lead the race of per capita consumption, with Switzerland being in the first place with a consumption of 144.7 m2 per hundred inhabitants followed by Greece, Spain, Portugal, Belgium and Italy. On the other hand, during the period 2001-2002 the generated stone wastes were 110 million tones according to EU data, from which only about 5 million tones were recycled or re-used mainly in the construction industry. These stone wastes the non-natural wastes such as oils or chemicals coming from the equipment and machinery employed for stone extraction and processing, are disposed in the environment, posing serious environmental threat. To achieve sustainable development of the stone sector appropriate methods that will prevent or reduce waste generation and disposal have to be identified and applied. In this work an extensive study of the stone waste management techniques applied in Europe is carried out, in order to identify the Best Available Techniques (BAT) that can be used according to the type of generated wastes and the waste management hierarchy: Waste minimisation, Re-use, Recycling and Disposal. The identification of BAT was performed based on 14 Sustainable Development Indicators (SDI), which were grouped into three categories: environmental, economic and social. The developed final list of BAT includes waste minimisation techniques, eco-management schemes, in-situ treatment and appropriate storage and selection.

Jan 1, 2007

By B. Day, L. Elinson

There is general agreement among those involved in occupational and public health that work-related diseases are under-diagnosed and under-reported. Highmark is particularly well positioned to carry out industry health analysis as it provides medical insurance for approximately three quarters of the insured population of Western Pennsylvania including some of the areas largest employers. The purpose of this study is to gain a more accurate understanding of the mining industry rates of respiratory diseases that maybe occupationally related and identify those inflated respiratory disease and hearing loss rates. Conditions examined included COPD, asthma, and pneumoconiosis.

Jan 1, 2004