Search Documents

By Pieter Hoekstra, Jim Hild, Mark Blohm

In the Basin and Range Province of Nevada, geophysics is used to assist exploration for bulk minable gold deposits, particularly over pediments. It is employed for mapping thickness of alluvium and Tertiary valley fill, for mapping covered structures, and for identifying alteration zones. In addition to potential field and seismic methods, three different electrical and electromagnetic methods are frequently used, resistivity-induced polarization, controlled source audiomagnetotellurics, and time domain EM. A review and comparison of the principles of these methods, illustrated by case histories, is the topic of this paper.

Jan 1, 1989

By T. J. van der Walt

This paper proposes a new methodology to model ill- defined processing operations using neural nets (NN's). A process with many variables (large dimensionality) cannot be modelled adequately if limited process data are available. This problem of multi-dimensionality is addressed and an approach suggested to reduce the dimensionality using NN's. The result of this modelling methodology is a combined model of phenomenological expressions and NN's. The model can successfully be incorporated in a dynamic simulator of the process. A new approach to conduct modelling on the basis of continuous data collected directly from an industrial processing unit, is also proposed. The modelling methodology is applied to a typical processing operation, the resin-in-pulp (RIP) process.

Jan 1, 1992

By W. L. Hollinshead

For more effective and cost-saving production in tunnels, the machinery used on construction sites in the future will be equipped with guidance systems combined with working-procedure management systems. This paper describes sensors for these systems and vari¬ous system configurations. A project is described that uses a computerized guidance system on an underground mining machine for guidance and profile control.

Jan 1, 2000

By C. J. Bise

Continuous mining accounts for about 69% of the nation's underground coal production. This level is not expected to change much in the near future. This is because continuous mining represents the primary means of under- ground coal production. It is also the primary means of driving development entries for underground coal mines, including longwall mines. The continuous miner worksite contains many characteristics that can lead to personnel accidents. It continues to be an area of concern for mine managers, safety engineers, and training coordinators. In an effort to assist mine management in attempts to reduce the number of accidents and injuries sustained in this area, this paper presents a loss-control-based, non-intrusive strategy for conducting safety evaluations at continuous miner worksites.

Jan 1, 1991

By T. R. Ellis

The author is the leader of the Extractive Industries Task Force of the International Valuation Standards Committee. The Task Force has developed an Extractive Industries section for inclusion in the International Valuation Standards (IVS). The Extractive Industries Guidance Note provides comprehensive standards for valuation of all minerals and petroleum industry property types for all valuation/appraisal purposes. The document is scheduled for release as an exposure draft for public comment by December 2003, then it will be finalized for publication in the IVS in mid-2004. This paper discusses the content and philosophy of the Extractive Industries Guidance Note within the context of the framework of the IVS. It also discusses the international implications and implementation of this IVS addition.

Jan 1, 2004

By T. J. Kim, S. Suh

The purpose of this paper is to evaluate overall prospects of the export market in the Pacific Rim for Illinois steam coal in terms of recent changes in global socioeconomic factors. To pursue this objective, three factors affecting the prospects of Illinois coal in the Asian market were selected for detailed analysis: quality requirements of imported coal, particularly those of the Japanese market; import controls and regulatory factors; and transportation factors affecting the export of Illinois coal. Based on these analyses, alternative long-term strategies are suggested for promoting Illinois coal export in the Asian market.

Jan 1, 1988

By Jeong-Heum Kim, Jan M. Mutmansky

The primary purpose of the research summarized in this paper was to experimentally investigate the performance of numerous mine ventilation network iterative solution procedures under controlled conditions to determine which procedures were most favorable in terms of number of iterations and total computational speed. The solution methods investigated included: (1) the Newton-Raphson method, (2) the Hardy Cross method, (3) the linear theory method, and (4) the second-order approximation method. The first three of these methods have been widely used while the fourth was formulated by the authors to investigate its potential for ventilation network computation. In addition to the four solution procedures, three methods for selecting the branches in the meshes and three methods for ordering the meshes for computational purposes were also studied during the investigation. As a result of these various options, a total of 36 combinations of solution methods, mesh selection procedures, and mesh ordering schemes were studied. To investigate the performance characteristics of these combinations, an identical set of 180 randomly chosen ventilation networks was used in sets of 30 networks at six different levels of complexity. Here, the level of complexity is defined as a function of the size (number of branches) and the density (number of nodes compared with the number of branches) of the network. To eliminate variations in the solution times due to differences arising from the fans, a single fan with a fixed characteristic was utilized in all the experiments. This paper will deal only with the results for the four iterative methods used to achieve solutions to the mine ventilation networks. The minimum-resistance spanning tree method for mesh selection and random mesh ordering was used throughout the analysis. The conclusions will be based upon a detailed accounting of the efficiency of each method using the total time to achieve a solution to each problem and averaged over the total problem set. However, the number of iterations and the time to complete each iteration will be studied in order to better understand the solution procedures.

Jan 1, 1991

By Anthony Harding, Rodolfo D. Aradas, Juan M. Fernandez, Darío Tsingas

"The adoption of tunneled combined sewerage interceptors and outfalls leads to design linings which are often subject to internal pressures that are larger than the external pressures, resulting in significant tension loads. The need to meet stringent durability conditions for the normal design life of 100 years often drives client specifications to require a double pass solution with a cast in situ secondary concrete lining. However, improvements in concrete technology and the need to seek efficiency in terms of time and costs, have driven designers to consider single pass segmental linings. The Riachuelo Sanitation project in Buenos Aires is subject to these constraints both upstream and downstream of a sewage treatment plant. This paper describes how the challenges of up to 2 bar pressure differential have been addressed by careful analysis of soil structure interaction to ensure that the full benefit of external ground pressure is realized, resulting in a more optimal design for the constructor both in terms of cost and time. INTRODUCTION The construction of long sewerage interceptors and outfalls is becoming an increasingly common piece of infrastructure for modern urban cities facing a large water front and estuarine conditions, which are under a significant environmental burden imposed by decades of sustained growth. Such works intercept most of the distributed sewage discharges to then divert them to a central treatment point from which it will be finally diffused via an outfall into a water body capable to accept these discharges under acceptable environmental conditions. Depending on the magnitude of the sewage load to be handled, the configuration of the urban environment and the conditions of the receiving water body, both in terms of oceanography forces and seabed conditions, these schemes will vary in length, conveyance capacity and design and construction requirements. When conditions permit, the current trend is the execution of long outfalls using flexible solutions (such as the use of HDPE pipes) which usually require some form of concrete ballasted weights to resist off shore dynamic forces when directly laid over the sea bed. However, this concept faces limitations when the conveyance requirements indicate the need for large diameters (typically above 3000 m) and also when the outfall needs to avoid deep features off shore such as navigation channels. When this occurs, tunneling, particularly segmentally lined tunnel constructed by TBM emerges as the most feasible approach for large diameter, long deep outfalls. The operating conditions often result in internal pressures that are larger than the external pressures, resulting in significant tension loads in the lining. The need to meet stringent durability conditions for the normal design life of 100 years often drives client specifications to require a double pass solution with a cast in situ secondary concrete lining."

Jan 1, 2016

By J. E. Oberholtzer, M. G. Fernald

INTRODUCTION Approximately six years ago the U.S. Bureau of Mines (USBM) developed a data acquisition system (DAS) specifically designed for measuring radon levels and other environmental parameters during studies of means to control radiation hazards in underground uranium mines. The DAS system records data in machine readable form using a paper tape punch, which represented the state-of-the-art at that time for a moderate cost output device. However, the use of paper tape as a recording medium for field studies is somewhat unwieldy. Reducing the raw data required either that the tape be shipped to a computer center equipped with a high-speed paper tape reader or that the tape be transmitted at low speed over the telephone lines to a remote computer. Transmitting, at ten characters per second, the data from a 10-channel DAS taking Four readings per hour would require about 30 minutes For each 24-hour day's data. Telephone lines from remote mine sites are often of marginal quality and data errors can be introduced during transmission. Paper tape punches are also prone to occasional punching errors. Both problems make it necessary to carefully check for and correct data errors, a process which is possible because each DAS produces an independent printed data record, but the error checking and correction process can be quite laborious. Aware of recent advances in microcomputer technology which have brought the price of a personal computer down to about the cost of a paper tape punch 5-10 years ago, the Bureau decided to explore the feasibility of using a low-cost personal computer in the field to process DAS data in real time. On behalf of the Bureau, Arthur D. Little, Inc., developed a simple interface circuit which permits an Apple II computer to accept data from one or two DAS units as it is being transmitted to the paper tape punches. Computer software converts each measurement to appropriate engineering units, e.g., radon concentration, Working Levels, air velocity, temperature, or barometric pressure. The computer also calculates 1-hour and 8-hour running averages of all converted data and prints those results as soon as they are obtained on a line printer located at the test site for immediate inspection. After development, the system was used continuously and successfully for a 5-month period at a Utah uranium mine. DAS DESIGN AND MODIFICATION Each of the two USBM data acquisition systems used in this work consists of two separate modules. A multiplexer module located below ground near the measurement transducers acquires signals from each of nine tranducers. Six input channels were devoted to measurements of radon or Working Level. The outputs of those transducers, photomultiplier tubes or G-M tubes, respectively, are digital pulse trains which are accepted directly by the mutliplexer. Three channels were used for environmental parameters--air velocity, temperature, and/or barometric pressure. Each of the environmental tranducers is fitted with dedicated linearizing and voltage-to-frequency conversion circuitry so that the outputs to the multiplexer are also pulse trains having frequencies of one tenth of the value of the measured parameter expressed in the appropriate engineering units. A 100-Hz reference signal was input into the tenth channel for use in monitoring system integrity and performance. All ten pulse trains are then timeseries multiplexed into a signal line for transmission to the above-ground data acquisition module. Above ground, the composite signal is de-multiplexed into ten separate lines, each of which is connected to a digital counter which converts the pulse train to a numerical value. The acquisition of each set of readings is initiated by an adjustable "scan cycle comparator" timer. The acquisition process proceeds in three phases. First, radon and Working Level channels are counted for an extended period of time, typically 5-10 minutes depending on activity, because of the low pulse rates involved. Then the other four channels are counted for ten seconds, and finally, all ten readings, along with the Julian day and time of day are output serially onto paper tape and printed on a strip printer. When the scan cycle comparator reaches its preset time (15-minute cycle times were used in this work), it resets itself, initiates another readout cycle, and begins timing again. The only modification made to the data acquisition systems used in this work was to disconnect the scan cycle comparator in one unit, which became the "slave" and bring in the scan cycle comparator signal from the other unit, the "master", to initiate data acquisition cycles in the slave. Synchronizing the two data acquisitions in this fashion and using two slightly different radon counting times insured that the two systems never attempted to output data to the Apple II at the same time. THE APPLE II COMPUTER The Apple II computer used in this work was equipped with 48 KBytes of semiconductor random access memory (RAM), two floppy diskette drives, a Centronics Model 730 impact matrix printer and a modulator for driving an ordinary color television as a video display device. A single California Computer Systems Model 7720A dual 8-bit bidirectional parallel input/output (I/O) card was installed in the Apple to accept the digital data from both data acquisition systems. This card is

Jan 1, 1981

By I. Shah, L. G. Austin

A method for quantitative investigation of the phenomena involved in fine grinding of materials that follows the changes in the breakage rates of fine particles has been presented. For relatively hard, brittle, non-coating material like quartz, the slowing down effect of breakage rates starts to be significant at relatively coarse sizes, which goes often undetected in closed circuit grinding systems, producing relatively coarse product, say P80=75µm However, for fine grinding systems, as the -10µm fractions begin to build-up, and classification becomes more difficult, the build-up of fine sizes causes a slowing down effect Compounding this problem is the difficulty of obtaining accurate cumulative weight size distributions in the fine size region.

Jan 1, 1983

By M. S. Prasad, K. J. Reid, M. P. Katsoulis

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two-year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the various process options adopted on bulk samples collected from the Minnesota River Valley area, which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion. HGMS and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size-reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota are briefly discussed.

Jan 1, 1992

By Makoto Terada

The most important consideration in planning the plugging and sealing of a mine for mine water control is to predict the water flow from the mine. For this purpose, a method of numerical analysis on the water behavior in the ground at the concerned mine area was developed and the mine water flows were simulated. A hydrological survey at the surface of the mine determined the recharge rate of ground- water and the apparent permeability of ground.

Jan 1, 1982

By Jan M. Mutmansky

While production scheduling for both surface and underground mining operations is similar in nature, a rather large array of techniques is applied in solving such planning problems. The techniques consist of both rigid operations research (OR) methods and practical procedures which are not mathematically based. In the following sections, a short summary of some of the techniques that are applicable to production scheduling problems in mineral operations is presented. The techniques discussed are: linear programming, integer programming, dynamic programming, graph and network theory, simulation, and heuristic methods. For an in-depth comprehension of these techniques, the reader is referred to any of the available textbooks on these subjects. One or more references will be listed for each topic to provide a starting point.

Jan 1, 1979

By Alice Blount, F. Patrick Carr

The quantitative evaluation,of quartz and other minerals in acid-insoluble residues from carbonate rocks and other industrial mineral products derived from sedimentary and low-grade metamorphic rocks is difficult. Commonly there are a dozen or more minerals present, and the suites vary from sample to sample. Because of these factors, either the absorption coefficient must be determined on a sample to sample basis or an internal standard must be used. Internal standards in general use are unsatisfactory. For example, [A1203] is often present in product samples because of ceramic grinding elements used in their production; CaF and LiF have peaks which overlap or nearly overlap mineral peaks in the samples. A careful evaluation has shown that magnesium aluminate (synthetic spinel) works particularly well as an internal standard for these types of samples. Not only does it have few, strong diffraction peaks which do not overlap, the peaks are in the same 28 region as the minerals, usually quartz and silicates, for which quantification is desired. Spinel also consists of equidimensional particles without prominent cleavages; this promotes a random orientation of the minerals in X-ray diffraction mounts. In addition, spinel can be used to correct for loss of diffracted-beam intensity due to thin sample preparations which are often unavoidable.

Jan 1, 1991

By J. F. Able, F. Djahanguiri

The US Bureau of Mines conducted research on underground stope leaching of metalliferous ores. Leaching underground would minimize the environmental impact of ore processing on the surface and would maximize minable reserves. An important aspect of this process is the minimization of pregnant solution losses and groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope-leaching economics. A reinforced-concrete bulkhead was designed, constructed and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead-design methodology and construction procedure.

Jan 1, 1998

By Finn Ouchterlony

INTRODUCTION Much of present fracture toughness testing con¬cerns chevron notched specimens (Newman Jr., 1984) since these, in principle, require neither fatigue precracking nor more registration than failure load to determine fracture toughness. Two such specimens which can be made from diamond drilled rock cores with minimal machining are the Short Rod (Barker, 1977) and the Chevron Edge Notch Round Bar in Bend¬ing or CENRBB Specimen (Ouchterlony, 1980). Even if the precracking property is especially valuable for a material like rock, practice has made the relative advantages of these chevron notched specimens much less apparent (Ouchterlony, 1982; Ouchterlony and Sun, 1983). Enough remains, however, to have the Commission on Testing Methods of the International Society for Rock Mechanics (ISRM) focus on them as standard configurations in a "Suggested Method for Determining Fracture Tough¬ness of Rock Material", which is in preparation. This paper presents material which supports the ISRM effort: 1. An experimental compliance calibration of the Chevron Bend (CENRBB or CB for short) and re¬sulting formulas. 2. Specimen tolerances, evaluation formulas, and loading rate requirements relating to both Short Rod and Chevron Bend Specimens of suggest¬ed standard proportions. 3. Some fracture toughness values obtained with the Chevron Bend Specimen. This material is mainly based on two reports (Ouchterlony, 1984 and 1985). CALIBRATION OF THE CHEVRON BEND SPECIMEN Preliminaries The specimen and basic notation is shown in Figure 1 together with a straight notched variety (SECRBB). Subscripts c and s are sometimes used below to distinguish between them. Assuming linearly elastic conditions the load point compliance [ ]

Jan 1, 1986

By John T. McDonough

The Climax Mine of AMAX's Climax Molybdenum Division is currently producing approximately 34,000 tons of molybdenum ore per day from two underground levels (see Figure I), and initial design is underway for the next deeper (1200) level. The aim of this report is to present the methods of site evaluation used at Climax for cavability determinations and underground support design. Climax succeeds with its panel caving system of mining (Julin, 1973) (Figure 2) largely because of the presence of pervasive geologic structural discontinuities. The stockwork ore body at Climax was formed by the multiple intrusion of mid-Tertiary rhyolitic magmas into Precambrian granite, schist and gneiss, and the hydrothermal emplacement of molybdenite into the network of fractures that were generated during the forceful upward intrusion of magma. Subsequently, intrusive events that were more deeply seated refractured the overlying, ore- bearing stock and propagated a complex system of axial and radial fractures. Post-ore movement along the Mosquito Fault (Wallace, 1968) and its associated stranded shear zones further fractured the ore body and disordered the existent geologic structure. The result of these structural events is a brittle, crystalline ore body that is transected by a complex pattern of faults, shear zones, and joints that augment cave initiation and enhance comminution of the ore blocks. Generalizations can be made about the structural trends within the ore deposit (King, 1946; Kendorski, 1973), however, the intensity and orientation of geologic structure is by no means uniform throughout the ore body. The relative intensities of silicic and argillic alteration are also highly variable (Vanderwilt and King, 1955). As a consequence, no single rock-mass model suffices as a standard for mine design, and site characterization for cavability and support design is a continuous process.

Jan 1, 1977

By Marie-Antoinette Dziurla, Barrie Johnson, Åsa Kolmert

Acidophilic bacteria are well known for their role in accelerating the oxidative dissolution of sulfide minds, such as pyrite. Other acidophiles, however, are able to catalyze dissimilatory reductive reactions. Bacteria that reduce ferric iron to ferrous, and sulfate to sulfide, were isolated from ARD-impacted environments and immobilised onto porous beads made of recycled glass. Column bioreactors containing colonized beads were constructed and peacolated with synthetic and actual ARD, and evaluated for their capacities to promote iron or sulfate reduction, and pH amelioration. Iron reduction did not require strictly anoxic conditions in bioreactors, and rates of up to 800 mg Fe3+ reduced/(l*day) were achieved, with a conversion efficiency of up to 98%. Using mixed populations of acidophilic fungi and iron-reducing bacteria, the bioreactors were capable of promoting iron reduction using paper pulp as sole carbon and energy source. Reduction of sulfate in pack bed bioreactors was observed with acidic wastewaters of pH 3 and above, though average rates of 300 mg sulfate reduced/(l*/day) were less than those recorded for circum-neutral pH systems. Bioremediation of ferric iron-rich ARD was assessed using coupled iron-reducing and sulfate reducing bioreactors.

Jan 1, 2000

By J. W. T. Ropkins, D. Allenby

The paper describes a technique by which large concrete boxes are unobtrusively inserted beneath existing highway and railway infrastructure to form new subways, culverts and under-bridges, thus avoiding the inconvenience and costs of disruption to traffic associated with traditional cut and cover techniques. A series of project examples, undertaken in the United Kingdom and United States, are used to illustrate the design and construction of the box structures, together with the technology required to control ground disturbance in the tunnel face and around the box, and the jacking systems necessary for box installation.

Jan 1, 2003

By J. A. Herbst, S. L. Blust

Optimization of blasting, crushing, and grinding operations is filled with challenges. One of the more difficult tasks is accurately sampling and determining the size distributions of blasted and crushed materials at a reasonable cost. The task is difficult because of the large size of fragments and the tonnage involved. However, the size distribution measurements are necessary for models that predict the performance of mine-through-mill operations. This paper is concerned with the use of video sampling for this task at National Steel Pellet Company's operation in Keewatin, Minnesota Data gathering, data analysis, model building, and mine-to-mill simulation are all described.

Jan 1, 2000