Search Documents

By Gurses Oner

In situ leaching is a relatively old mineral extraction method; however, historically only a small portion of copper has been produced from small scale operations. Recently, in situ leaching technology because of its intrinsic advantages over conventional mining and milling is being considered as a viable option for recovering copper from both low grade oxide and sulfide deposits. This paper presents the application of computers to investigate in situ technology using large whole core leaching experiments. Computers were applied to three different areas: (1) experimental control and data acquisition, (2) non-destructive evaluation of samples using x-ray computed tomography and image processing and (3) mathematical modelling and data analysis.

Jan 1, 1992

By D. K. Denton, D. F. Scott, T. J. Williams

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, de¬tect hazardous ground conditions and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep, >1,220-m (>4,000¬ft), underground pillars. If high¬stress areas are detected, they can be destressed prior to development or they can be avoided High-stress ar¬eas can be monitored with succes¬sive seismic surveys to determine if stress decreases to a level where de¬velopment can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost¬effective, efficient and noninvasive. Also, investigators can monitor large rock masses, as well as moni¬tor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer envi¬ronment.

Jan 1, 2000

By S. Bhattacharya, M. M. Singh

The Surface Mining Control and Reclamation Act of 1977 (SMCRA) requires under-ground coal mine operations to prevent "material damage" to renewable resource lands caused by subsidence. However, what constitutes material damage is not defined. This paper discusses the applicable criteria for agricultural lands, forests and grazing lands, surface water bodies, and ground water aquifers. Although data on the subject are limited, an attempt is made to present quantitative guidelines to distinguish between moderate and severe damage due to subsidence.

Jan 1, 1988

By Robert E. Goodwin

There are four main requirements which must be considered when selecting a wire rope for the best serviceability. A proper choice is made by correctly estimating the relative importance of each of these requirements and selecting s rope which has those qualities best suited to withstand the combination of destructive forces expected under continued service. A wire rope should possess: 1. Strength sufficient to support the maximum load expected and with s proper safety factor. 2. Ability to withstand bending and to resist bending fatigue without failure of the wires. 3. Ability to withstand surface abuse such so abrasive wear, pounding, and wire scrubbing. 4. Ability to withstand abuse such as crushing and distortion.

Jan 1, 1968

By S. L. McGill, P. B. Comba

Many gold producing states are requiring rinsing of spent heaps to render the leached ore compatible with the environment and are placing reatrictiona on effluent pH, cyanide, and metals concentrations. Parameters which may affect efficient rinsing of heaps have been investigated by the U.S. Bureau of Mines in laboratory column studies. Rinse profiles for cyanide, metals, and pH as a function of the volume of water passed through the spent ore are presented. Fresh water rinsing of spent ore in columns showed that rinsing of cyanide was not affected by the rinse solution application rate. Interrupted rinsing with a rest period between applications reduced the volume of water required to meet effluent cyanide concentrations. Chemical oxidation of the effluent with recycle of the rinse solutions reduced effluent cyanide concentrations and the volume of waste solution generated. Water rinsing was not successful in reducing the alkalinity of the cement agglomerated ore. A dilute acid solution had to be applied after cyanide removal to reduce effluent pH levels to specified limits.

Jan 1, 1991

By R. J. Sweigard

Many states are considering the need to establish or modify policy relating to the disposal of coal ash. One of the primary concerns is the impact of leachate from the ash disposal sites upon groundwater and nearby bodies of surface water. A detailed site investigation was conducted at a coal ash disposal facility associated with a power generation station. The disposal site is situated alongside a major river. Monitoring wells were installed and soil samples were taken for characterization. Groundwater models were used to simulate migration of leachate from the disposal site toward the river. Such models have the potential to be used to verify regulatory compliance. This paper addresses the validation and adaptability of these models to this case and their usefulness as possible tools to be used in future environmental audits.

Jan 1, 1993

By Michael G. Nelson, Hanguang Wu, V. Izaxon, Sukumar Bandopadhyay

The method of mine ventilation involving heated air, which is frequently used in mines in cold regions, does not correspond to the natural conditions prevailing in permafrost regions; it is not economical and leads to a series of complications which can be prevented or greatly reduced by lowering the temperature of the air stream entering the mine until it is equal to or very close to the temperature of the frozen ground This paper presents ventilation design approaches which can be engineered to provide the required micro-climate and thus en- sure the stability bf the ground for placer mines in permafrost. Specifically three ventilation design approaches are presented: 1) design based on minimum thermal impact; 2) design based on positive/negative heat accumulation in the existing mine airways; and 3) design based on heat exchanging devices such as thermosyphons placed above ground.

Jan 1, 1997

By Michael S. Kucker, Robert A. Robinson, Harvey W. Parker

Ground deformations are of major concern during tunneling, especially in downtown environments, since they have a significant impact on the costs and practicality of tunneling. This case history describes soil and groundwater conditions and ground behavior during the construction of twin transit tunnels for the Downtown Seattle Transit Project (DSTP). The tunnels were excavated through complex glacial soils ranging from hard glaciomarine drift to flowing sand. The tunneling process was greatly facilitated by the prediction of soil layer positions to an accuracy of ±0.6 m (2 ft). Tunneling was complicated by the presence of over 500 temporary tiebacks and by disturbed ground overlying an operating railroad tunnel. A variety of ground improvement techniques were used to successfully minimize settlements, which ranged from 1 cm (0.4 in.) in glaciomarine drift to 6 cm (2.4 in.) in flowing sands. Ground improvement techniques included compaction grouting, chemical grouting, jet grouting, and eductor well systems.

Jan 1, 1991

By Robert T. McKnight

Introduction The minerals exploration business, like many businesses, is faced with the problem of valuing future, risky cashflows. These cashflows are derived from those mineral deposits which have been successfully commercialized. Many deposits, however, do not have the quantities or grade of ore to be considered economic at the projected metal prices using the traditional tools of the Capital Asset Pricing Model and discounted cashflow analyses. If one calculates the future revenues, costs and cashflows of one these marginal properties, and discounted it at the appropriate risk-adjusted discount rate, it may have a negative present value. Yet such a property may still have real, positive value in the marketplace. Why would a firm pay money for a property with an (apparent) minus present value? Mining properties such as these are bought and sold in arms- length transactions on a regular basis. Why is this so? Part of the reason relates to the nature of ore reserve information. To generate cashflows, the analyst must t assume that the reserve information is known with certainty when, in fact, reserves are not known with certainty. Mineral reserves are a function of commodity price, extraction costs and the level of (usually drilling) information about the reserves. Stated, or currently known, mineral inventories may vastly understate the true state of nature. Some firms may therefore be buying a property based on a completely

Jan 1, 1988

By Neil B. Prenn

Drill-hole contamination has been a problem for many years. Contamination of rotary drilling has been well documented. More recently contamination in wet reverse circulation drilling has been noted by Echo Bay and others at the 1991 AIME annual meeting. Mine Development Associates (MDA) has worked on a number of projects at which contamination of drill-hole samples has occurred. Properties are commonly acquired with drilling accomplished by other companies and at times the only records of the drilling program are the drill-hole logs and assays themselves. Identification of contaminated zones is sometimes difficult to determine. Most geologists and engineers in the industry are aware of the magnitude of the problem, as contamination is a relatively common problem with wet reverse circulation drilling. MDA has developed a computer program to help determine if contamination has occurred when using reverse circulation drilling, based on cumulative distribution curves and by a process we call decay analysis. Most deposits are not homogeneous throughout the deposit, but exhibit a characteristic drop-off or decay of assay values around higher-grade drill-hole intercepts. Using graphs of this characteristic decay and cumulative frequency distribution, we can use the program to help determine contamination in several ways. This paper will discuss the use of decay analysis at three gold deposits where contamination is known to have occurred. In one of the deposits decay analysis was used, successfully to determine if contamination had occurred, while in the other two the decay analysis was used to verify our decay analysis procedure.

Jan 1, 1992

By Michael Michaylov, Elana Vlasseva

This paper presents a method for three-phase foam preparation recipe optimization. The pressurized foam is injected into porous media of gob area for prevention and fighting of SPONCOM fires. The method includes laboratory experiments for main foam properties as well as mathematical optimization procedure. Optimization criteria are formulated reflecting foam application purposes. The influence of solid phase on foam heat stability is shown. Results from optimization procedure for four foam agents by varying fly ash consistency of foam are presented. Theoretical basis for original construction of foam generator, specially constructed for of three-phase foam generation, is set u

Jan 1, 1997

By F. F. Peng, Z. Lu

Employing a combination of two types of polyelcctrolyte might become necessary to enhance both the settling rate of the flocs and the water clarity of a fine-particle suspension in a high-capacity thickening process. The sequence of addition, mixing, type and dosage of polymer all affect the overall performance and capacity of a thickening process. For the sedimentation of copper flotation tailings, the cylinder test results showed that two different techniques may be used to achieve the required performance, i.e., a high settling rate of the flocs and the deisired underflow density and overflow water clarity. The required performance can be achieved by either adjusting the pH prior to anionic polyelectrolvte flocculation or using a combination of polymer flocculant and coagulant (dual-polymer system). The dynamic thickening test results showed that only the approach using a dualpolymer system is capable of meeting the required performance. The effects of polvelectrolvte dosage, the sequence and numbers of polyelectrolyte addition, the feed concentration, the bed level and the rake speed on the settling rate, underflow percent solids and water clarity were studied in cylinder tests and in a laboratory dynamic thickening unit. The dynamic test is especially valuable in evaluating the addition and mixing of polymers. The results were evaluated quantitatively using total suspended solids in supernatant, underflow density and capacity per unit of settling area per unit of time. The objective of this study was to quantify and explain some of the parameters involved in the sedimentation of copper flotation tailings.

Jan 1, 1999

By B. Jensen, B. K. Abraham, G. J. Tuck, A. D. S. Gillies

A dust concentration meter has been developed with Australian coal industry support for the measurement of total airborne dust concentrations capable of causing explosions in underground coal mines. The instrument, The University of Queensland Dust Meter (UQDM), measures the effective dielectric constant of a mixture of coal dust and air that is drawn between the plates of a capacitor, the capacitance of which is measured by a ratio-transformer bridge and synchronous detector system. This technique measures small changes in capacitance to approximately 1 part in 106. The unique design of the capacitor sensor permits a precise volume of coal dust and air mixture to be sampled. This arrangement overcomes difficulties inherent in optical dust measurement. The meter is portable, battery powered, incorporates data logging and has intrinsic safety approval. The operation of the meter is discussed. The system is designed to monitor dust concentrations along a coal mining face and provide concentration profiles leading to the development of suppression strategies. If data from underground tests are available, the meter's potential to contribute to establishing safe working conditions underground will be discussed. Other areas of potential application of the measurement technique are also examined.

Jan 1, 1993

By J. C. Emerick

Preliminary investigations have shown that wetland-based treatment systems can be an effective and relatively inexpensive control strategy for mine drainage pollution in eastern coal mining regions. This strategy also has potential for western mining regions, although too few systems have been installed in the west to permit general evaluation of the concept for western climates. The construction of prototype systems is encouraged for some situations. Wet-land environments have the capability of removing metals by natural geochemical and biological processes, including precipitation, filtration, ion absorption, and biological uptake and accumulation. Data presented for natural wetlands receiving mine drainage show removal of iron and other metals, and high accumulation of metals in soils and plants.

Jan 1, 1988

By Margaret Armstrong, Chris Roth

One advantage of kriging is that it provides both an estimate of the block or point grade, and an indication of the local precision via the kriging variance. If one assumes that the estimation errors are normally distributed, then confidence intervals for the grades can be calculated. But in mining, grades are rarely normally distributed; in general, they are skew. This is particularly true for precious metals. In this paper we study confidence intervals for variables with non-normal distributions. Using a non linear geostatistical technique, the grades are transformed into their normally distributed equivalents. Confidence intervals are obtained for these normal variables, and back transformed to give the corresponding confidence intervals for the grades, for either points or blocks. This approach is applied to gold data from the Witwatersrand basin in South Africa.

Jan 1, 1996

By P. C. O. Chukabarah

Atkinson's resistance square law is the cornerstone equation for traditional expression of energy losses in mine ventilation engineering. But the nomenclature for the various forms of energy losses are often confused for one another, misapplied or misinterpreted. These forms of energy were re-examined from thermodynamic and fluid-dynamic perspectives. Resultant expressions showed that both incompressible and compressible flow regimes in underground mines can easily be accommodated. Given the well-known three major energy forms, which are equivalent to one another but numerically unequal, corresponding equations to Atkinson's (pressure loss) for headloss and workloss were derived. The thermodynamic weight relational resistance ([w] s2/m5) associated with energy per unit weight (headloss) was dimensionalized for the first time. Also, normalized Atkinson-like equations for headlosses and worklosses were derived to ease direct computations in mine ventilation practice.

Jan 1, 1995

By JIAQI JIN, Chen-Luh Lin, Amanda N. Erskine, Jan D. Miller, Shijie Wang

The liberation and exposure of valuable mineral grains in ore particles are of significant importance in understanding the efficiency of flotation separations. A flotation feed sample from the Kensington concentrator was scanned by micro Xray computed tomography (micro-XCT), to determine the liberation and exposure of auriferous pyrite grains. The analysis results suggest a satisfying extent of liberation for particle sizes smaller than 212 μm. Theoretical flotation recovery of pyrite for selected particle size fractions was predicted from the three-dimensional liberation and exposure analysis. The plant flotation tail was also characterized by micro-XCT to identify liberated and partially liberated pyrite particles that might not be collected into the concentrate. However, liberation analysis of the tail sample revealed that the majority of liberated pyrite was recovered in the plant flotation circuit. Trainable Weka, a machine learning segmentation approach, was compared with the Watershed thresholding segmentation for the 106 × 45 μm particle size fraction scanned at a voxel size of 1.85 μm. Improved segmentation of small particles was found using the machine learning method.

Mar 1, 2024

By R. K. McFarland, E. S. Diamant, L. Blake

A number of concepts for basing strategic missiles facilities deep underground have been developed within the defense industry. Recently, several contracts were let by the Air Force Ballistic Missile Organization to better develop system concepts for Deep Basing and Rapid Egress of Missiles from these facilities. A particular challenge of the Deep Basing Concept is the need for the excavation of egress tunnels or shaft from the deeply based facility to the ground surface, in a rapid and reliable manner. This Paper describes a conceptual MX-Deep Basing Facility, the technical issues associated with its design and construction, and potential means for achieving rapid egress from this facility. Manuscript not received in time for publication.

Jan 1, 1983

By R. T. Swinderman

"Virtually every article you read on safety has a statement to the effect: “It’s obvious that safety pays”. If it is so obvious, why is it so hard to answer these questions? • How does the Maintenance or Operations Manager convince the Plant Manager to spend money from the annual budget for safety improvements? • How does the Plant Manager influence Corporate to prioritize safety improvements? • How does an engineering firm persuade the owner to spend more on design and equipment up front to reduce risk? There are many cultural and structural reasons why it is so difficult to prove the obvious. In my opinion the main culprits are: the almost universally used ‘Low Bid’ process, variations in reporting incident statistics between industries and countries, and, the Generally Accepted Accounting procedures (GAAP) [or International Financial Reporting Standards (IFRS)]. Conventional wisdom is it’s smart not to spend more than you need to meet the minimum regulations and maximize production. But buying on price alone often harms people, degrades the environment, and reduces the company’s bottom line. How can this be? You met the minimum safety requirements and saved money by buying on price. Don’t those savings go right to the bottom line? When you buy on price you get minimum quality, minimum compliance and are often backed corner with no reasonable options to rectify the problems that arise from buying on price instead of buying on long term life cycle cost. Culturally few companies actually ‘walk the talk’. It is trendy to have giant billboards at plant entrances proclaiming world class compliance with quality and safety standards. Annual reports are embellished with safety slogans and sustainability statements. Behind the front gates and the glossy annual reports the message is clear: produce or be replaced. Only a few companies go beyond the window dressing and actually endorse, from the top down, continuously improving their safety culture. Those that do embrace safety, show significant performance advantages over their competition that are reflected in their safety, productivity and environmental records and, ultimately their financial statements and share price. Current accounting (and reward) systems make it unlikely financial managers will accept non-conventional approaches to justifying expenditures on safety because they are driven to report “hard” numbers that can be documented and are within the “GAAP or IFRS Rules.” But in reality, accountants quantify soft or intangible costs all the time in their financial statements. Justifying safety investments is greatly enhanced by quantifying what most financial managers would call intangible costs. Government agencies have no problem assigning intangible costs to justify regulations to improve safety. How many times have you heard that the regulation is justified because the cost to industry is X while the benefit to the society is 2 or 3X? How can they say that without including intangible costs? We find it hard to believe these government claims of benefits to society because we have been trained to think about saving hard direct costs to justify investments."

Jan 1, 2017

By R. T. Leigh

The continued decline In the production of synthetic soda ash (sodium carbonate) due to high costs and associated environmental factors, has improved the world demand for natural soda ash. The largest resource of natural soda ash is the mineable trona deposits of Southwestern Wyoming. Wyoming trona, a lacustrine evaporite of Eocene Age, is mined by five producers which process over 90% of the United States and 20% of the worlds soda ash. Total world consumption of soda ash is forecast to grow 1% annually. Increased expansion into foreign market's is absorbing the domestic overcapacity.

Jan 1, 1989