Search Documents

By Michael G. Strominger, Anthony E. Gross

The development of precious metals ore agglomeration with a cement binder, by the U.S. Bureau of Mines, has allowed the economical heap leaching of low grade gold ores (<0,05 oz/ton) over the last decade, Even with the Bureau of Mines technology, numerous operations continue to experience channeling and blinding problems. A research project was undertaken at Nalco Chemical to address situations where improved agglomeration is needed, By increasing the incorporation of fines into the agglomerates,the segregation of ore by size which occurs from handling will be reduced and channeling minimized. A stronger agglomerate will reduce fines migration during leaching and prevent blinding of the heap, Both of these changes will give an even flow of barren solution throughout the heap and give solution contact with all of the ore. This paper presents the development of polymeric agglomeration aid, Nalco 9760 which has given a higher rate of and a higher total gold recovery in plant evaluations.

Jan 1, 1990

By Robert W. Bartlett

Heap biooxidation of sulfidic refractory gold ore requires large amounts of oxygen, as shown in Figure 1. Bacteria, Thiobaci/lus ferrooxidans, are donnant at oxygen concentrations below about 3% in air (1 ppm in aqueous solution) because ofmonod kinet­ics. Hence, the maximum possible utilization is only about 75%, and it may be much less than that due to poor air sweep effi­ciency. At the maximum oxygen utilization, an ore containing two percent pyrite requires nearly 100 cubic meters of air per tonne (4,000 cubic feet per ton). The stoichiometric air require­ment to oxidize arsenopyrite is similar to that of pyrite. While the leaching solution percolating through the heap introduces some dissolved oxygen, the amount is insignificant because of the low solubility of oxygen in water, 7 to 8 ppm at atmospheric saturation. There are only three ways to provide oxygen to the heap: either air flow by natural convection, diffusion of oxygen from the surface (through stagnant air in the air-filled void space in the heap), or forced air ventilation of the heap. Each of these processes will be reviewed.

Jan 1, 1996

By Steve Richards

Incorporating a bottleneck analysis into the mine plan can provide a significantly better basis to make economic decisions regarding materials handling systems. Every materials handling system has a bottleneck. The bottleneck at a mine may change over time as a function of location or time. Since a mining reserve is a finite amount and can usually only be mined once, knowing how the bottleneck changes can provide a critical backdrop to capital investment decisions, especially those affecting the materials handling system. A bottleneck analysis can better quantify the expected &apos;return and also indicate the optimal time to complete tile project.

Jan 1, 2002

By J. A. Herbst, R. Zaragoza

Conventional control schemes in use today are not able to produce satisfactory control when high-frequency disturbances are present in the flotation feed. An advanced model-based control scheme is presented here as a promising solution to this control problem. The main feature of this control scheme is the real time identification of the unknown disturbances in the first few cells of the flotation circuit. This information is used to control the rest of the flotation plant in a feedforward fashion. This control scheme also provides flexibility to meet any metallurgical, economical, or management objective.

Jan 1, 1987

By Stephen Hoffman

The Environmental Protection Agency (EPA) is investigating approaches to control non-coal mining wastes. In May 1988, the EPA&apos;s Office of Solid Waste (OSW) released a document that outlined an approach to manage non-coal mining wastes and materials. This document was called Strawman I. It was a staff-level approach designed to aid the continued participation of interested parties and to enhance EPA&apos;s understanding of mining waste issues. EPA has been working with states, public interest groups and the mining industry to gather information and to solicit input on waste management approaches. The involvement of the states in the Strawman process has been coordinated by the Mine Waste Task Force of the Western Governors&apos; Association and the Interstate Mining Compact Commission. Involvement of public interest groups has been coordinated through Colorado Trout Unlimited. And the participation of the mining industry has been managed principally by the American Mining Congress. In May 1990, EPA released Strawman II. It was based on comments submitted to the EPA on Strawman I and on information given to the EPA by interested parties since 1988. Strawman II is again a staff-level approach to protect human health and the environment from wastes and other materials associated with non-coal mining. In September 1990, meetings were held with public interest groups and the mining industry to discuss their comments on Strawman II. By early 1991, the EPA expects to make a decision on how to proceed with program development.

Jan 1, 1990

By L. L. Gagné

The Churchill Falls Development will eventually be the largest source of hydroelectric power in North America. Churchill Falls was discovered in 1839, but until recent years it was not practical to begin development of this site to tap the 7 million horsepower available. This $1 billion project is located in Labrador, 700 miles northeast of Montreal and 650 miles northwest of St. Johns, Nfld. The construction will divert the Churchill River 5 miles upstream from the 245 foot Churchill Falls. Rapids above and below the Falls, together with the Falls proper, give a natural head of 1,040 feet. In contrast to the basic simplicity of the surface installations, the powerhouse labyrinth is astounding in size and complexity. The largest in the world, it consists of three major chambers - the powerhouse, 972 feet long by 81 feet wide and 154 feet high; the surge chamber, 763 feet long, 40 feet to 64 feet wide and 148 feet high; and the transformer gallery, 856 feet long by 50 feet wide and 39 feet high. Other major features include eleven inclined penstocks, each 1200 feet long and 20 feet in finished diameter; eleven draft tubes averaging 37 feet in finished diameter and 162 feet long; six vertical cable shafts each an average of 865 feet in length; a series of eleven short bus tunnels linking the powerhouse and the transformer gallery; a vertical power-

Jan 1, 1997

By Michael M. Carroll, Zhu-ping Duan, Han-ping Chin

INTRODUCTION The inelastic stress-strain behavior of rocks has urged engineers to seek for the possible application of plasticity to engineering pro¬jects such as tunnels, oil wells, dams, etc. for a long time. Early efforts in this direction have tentatively used the classical theories to solve some axisymmetric problems, in which the rocks were treated as perfectly plastic and nonfrictional materials (Talobre, J. A., 1957). Meanwhile, one of the fundamental assumptions is that the volume strain of elastoplastic material is purely elastic. Drucker and Prager (1952) developed a perfectly plastic and frictional model with a generalized form of Mohr-Coulomb law, which serves as both failure criterion and yield criterion. Although the associated flow rule gives unacceptably large dilatancy, this model is a very important step to deal with the frictional behavior of geological materials. As a further step, Roscoe et al (1963) and Schofield and Wroth (1968) proposed a Cam-clay model, which accounts for the yielding before the material reaches a failure envelope and reflects the plastic volume strain as a strain hardening factor, and the open end of the Drucker-Prager envelope is capped by a family of yield surfaces, the envelope is made conforming with crit¬ical void ratio line. The proposed shapes of the cap have been based on experimental data and on convenience of mathematical descrip¬tions. Drucker, Gibson and Henkel (1957) introduced a spherical cap for soils, while in Cam-clay model the cap is semi-logarithmic yield function derived from the result of triaxial tests. DiMaggio and Sandler (1971) proposed an elliptical model for sand, in which the hardening function depends exponentially on plastic strain. Sandler et al (1976) used a plane cap model to express the behavior of a wide range of geological materials of which the nonlinear hysteretic nature is significant. Mizuno and Chen (1982) illustrated the physical mean¬ing of cap models and their adaption to finite element calculation. In recent years, Carroll et al (1972, 1980) have studied the com¬paction of porous materials under hydrostatic pressure and discussed the mechanism of the nonlinear response thoroughly. Analytical and numerical analysis of the hollow sphere model by Curran and Carroll (1979) predicted an initial yielding surface, dependent on the initial porosity, and showed a strong coupling between hydrostatic and deviatoric effects. All these main features from the abovementioned theoretical research are visualized by the experimental data on Boise sandstone (1984). The combination of such previous work would be logically the construction of a plasticity model for porous rocks which, following the tradition of assigning the name of birthplace to a special model, is called Cal-Rock model (Carrol, M. M., 1984). The results of triaxial tests along different loading paths reveal the compaction characteristics for deviatoric and hydrostatic stress separately. the fitting of the nonlinear stress-strain curves leads to a construction of yield surfaces. Moreover, an uniaxial strain test gives the strength envelope which is the critical state line. The whole model is composed in the frame of elasticity theory. The concept and representation of plasticity used here are in the spirit of Naghdi¬Casey theory (Casey and Naghdi, 1984 and 1984, Naghdi and Trapp, 1975). In order to find the way of using such a plasticity model in engineering problems, the stress field in a thick-walled cylinder of porous material is calculated. This is an axisymmetrical problem with plane strain, which is an idealization of oil well in an infinite medium. Because the constitutive relation is highly nonlinear, a numerical method has been utilized to obtain the solution. CONSTRUCTION OF CAL-ROCK MODEL (1). Elastic-plastic constitutive equations The basic assumption is that the yield surface in stress space depends on one parameter, namely the plastic volume strain, as the data on Boise sandstone suggested. Starting from this point, the theory formulated in stress space and in strain space by Naghdi and his co-workers (1975, 1981) can be simplified. The simplified yield function is

Jan 1, 1986

By F. D. Mendes, A. H. Martins

The high copper grade in the Igarapé Bahia (Brazil) gold-copper ore restricts the direct application of the classical cyanidation process. Copper oxide and sulfide minerals react with cyanides in solution, causing high leach-reagent consumption, raising processing costs and decreasing gold recovery. According to studies, a feasible solution would be to pretreat the ore to remove copper minerals prior to cyanidation. The goal of this experimental work was to study the conditions for the removal of copper from the Igarapé Bahia gold-copper ore by sulfuric acid leaching, applying a statistical approach to the experimental design. By using the Plackett Burman method, it was possible to select the variables that exhibited the largest influence on copper extraction at the sulfuric acid leaching stage. These variables were leach solution temperature, stirring speed, sulfuric acid concentration in the leach solution and ore particle size. The individual effect of these variables and their interaction influences on the experimental response were analyzed by applying the replicated full-factorial design method. Finally, the selected variables were optimized by the ascending-path statistical method, which determined the best leach experimental conditions for maximum copper extraction. The optimized leaching conditions resulted in a copper extraction of 75.5%. Keywords: Copper, Gold, Extraction, Sulfuric leaching, Optimization

Jan 1, 2003

By Ammar Henchiri

INTRODUCTION A current need of the phosphate industry is the development of process technology for treatment of high carbonate content ore. About 75 to 80 percent of the world phosphate reserves (1) are associated with carbonate gangue, which is not amenable to treatment by the existing techniques. Numerous laboratory and pilot plant studies have been devoted to carbonate-phosphate separation. Different techniques were involved (washing, sieving, attrition, flotation, calcination, and leaching). For technical and economical considerations, flotation appears to be an efficient process for this problem. Separation of carbonates (calcite and dolomite) from igneous phosphate is applied in industrial plants in Brazil, Finland, and South Africa. But, for sedimentary phosphate, no industrial realization exists at this time, with the possible exception of some plants in China. The main problems with sedimentary phosphates are: • high substitution by CO3-2 and F- for P04 -3 in the apatite lattice. • larger surface area of the phosphate particles because their surface is porous and irregular. • tendency of sedimentary minerals to produce more slimes in conditioning than the crystalline minerals, hence, larger dosages of collectors are required for sedimentary minerals. Investigations reported in the literature indicate that most processes developed for sedimentary carbonate-phosphate separation involved inverse flotation of carbonates using fatty acids as collectors (2), (3) associated with phosphoric acid (4), monosodium phosphate (5), F- (6), or SiF6 -2 (7) as phosphate depressants. Later investigations, conducted by A. Henchiri and G. Baudet (8), (9), (10), (11), (12), (13) in the BRGM technology department, of phosphoric esters revealed that these reagents are selective collectors for carbonate-phosphate separation. The above investigators developed a process which used phosphoric esters to collect carbonate minerals and sulfuric acid or sodium fluorosilicate as depressants for phosphate. Extensive comparative tests for different processes on the same phosphate sample show that the process developed at BRGM is one of the most promising methods proposed for sedimentary phosphate-carbonate separation. It should be pointed out, however, that phosphoric esters make abundant froths. The handling of these excessive froths will be a problem in an industrial-scale plant. This paper outlines test work performed in order to optimize and to improve the efficiency of the flotation process on a sedimentary phosphate ore selected from the Sra Ouertane orebody. The Sra Ouertane flotation process, illustrated on Figure 1, first removes carbonate minerals by inverse flotation and then recovers phosphate as a froth product, leaving quartz as a cell product.

Jan 1, 1993

By T. R. Ellis

"Editor’s Note: This is an expanded abstract. The full report is available on SME’s website at http://www.smenet.org/publications-resources/ resources/sme-valuation-standards-tutorials.The author has three goals for this review of mineral valuation standards internationally.1. To place the SME Standards and Guidelines for Valuation of Mineral Properties (SME Valuation Standards) and International Mineral Property Valuation Standards template (IMVAL Template) within the global context of existing mineral valuation standards.2. To review the current status of harmonization of each International Mineral Valuation Committee (IMVAL) member’s mineral valuation standards (or code) with the IMVAL template and suggest remedies for issues found.3. To suggest future enhancements for the IMVAL Template and SME Valuation Standards, and to suggest future roles for the IMVAL and SME committees. From the author’s review, Ellis draws the following conclusions.The SME Valuation Standards comprise a minimum set of principles-based standards and guidelines for developing and reporting valuations of mineral properties (including petroleum properties) for public and private use, subject to jurisdictional requirements. The standards are also designed to provide mineral valuation guidance that supplements application of the International Valuation Standards Council’s International Valuation Standards (IVS) and the U.S. government endorsed Uniform Standards of Professional Appraisal Practice (USPAP), published by the Appraisal Foundation.The SME Valuation Standards is the first set of valuation standards developed by a minerals institute adopting and modifying the IMVAL template. As a result, the SME standards are essentially totally harmonized and otherwise aligned with the IMVAL template. IMVAL was initially conceived in 2012 as a discussion body to aid harmonization of each member’s valuation standards, by modifying to function the same. IMVAL primarily developed the IMVAL template, published in July 2016, to produce an agreed reference framework of essential mineral valuation guidance content as the goal for harmonization of the Australasian Code for Public Reporting of Technical Assessments and Valuations of Mineral Assets (VALMIN Code), The South African Code for the Reporting of Mineral Asset Valuation (SAMVAL) and the Canadian Standards and Guidelines for Valuation of Mineral Properties (CIMVal standards and guidelines). The harmonization would result from each mineral valuation standards committee modifying its standards to operate similarly to the IMVAL template, producing valuation reports with similar content and value for the same mineral property. The template is also available for other bodies to adopt and modify for their regional setting’s needs, as SME did, or use as a convergence goal when updating an existing standard."

Jan 2, 2018

By V. P. Keran, K. Leung

Two 32 foot x 14% foot, 6.4 MW autogenous mills have been installed in the Mount Isa Mines Copper Concentrator to replace the fine crushing plant, fine ore bin, rod mills and primary ball mills. This paper describes the reasons for the change, the rationale for the new circuit design and configuration, the design and scale-up processes used to size the mills, considerations for the installation of large mills inside an operating concentrator and some early operating data.

Jan 1, 1992

By A. Ferreira Morgado

The sodium smectitic clays (bentonites), have more industrial applications in that class of mineral, a driving force to obtain this mineral. In Brazil, there are several occurrences of smectitic clays, unfortunately they are polycationic, with a distribution of several exchangeable cations, where the cation sodium occurs in minor quantity. In this work, the original polycationic smectitic clay was firstly proper characterized and then treated with sodium carbonate obtaining homoionic sodium smectitic clay. The rheological tests in the optimized sodium smectitic clay showed good results for drilling fluids, typical of a sodium bentonite ones.

Jan 1, 1999

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) and a cooperating longwall trona mine in the Green River basin of Wyoming in the United States. The objective of the study was to evaluate the movement of longwall face air and exchanges between the face and worked-out areas to document the presence or absence of face airflow pathways between these locations. Tracer gas experiments using sulfur hexafluoride (SF6  ) were conducted to describe air movement on the face and in the mined portion of the active panel. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of gases emitted from the face and caved gob.

By Isabel F. Barton, Christian A. Rathkopf, Mark D. Barton

Rhenium (Re) is one of the rarest elements on earth and is a designated critical element in the United States and European Union for its uses in superalloys. Unusually among critical elements, Re is produced entirely as a byproduct of molybdenite (MoS2) mining, as pure Re minerals are extremely rare. However, Re concentration in natural molybdenites varies from a few parts per trillion to tens of percent. There are few known consistent patterns and no firmly established reason for this variation, making it difficult to use molybdenite Re content as a proxy for metal grades, a vector to high grades, a clue to the geological and geochemical nature of the ore deposit, a guide to overall Re resources or for any other of the applications that have been suggested for it over time. 

By Leandro Augusto Viana Teixeira, Angela Avelar, Ruberlan Gomes Silva, Virginia S. T. Ciminelli, Daniel Majuste

Rare earth elements are essential for modern life products and green technologies. Recent supply constraints have boosted the development of rare earth projects after the price peak of 2011. The feasibility of a project depends on the definition of a processing route, which in turn depends primarily on the rare earth mineral, with monazite and bastnaesite representing the two most relevant minerals. Monazite-type ores usually contain high acid consumption impurities, such as iron, aluminum, calcium, magnesium and phosphates, and may also contain prohibitive levels of radioactive thorium in its composition. Based on thermodynamic analysis, the present work discusses the fundamentals of a selective process route for rare earth extraction from monazite ores with high iron content. This process involves sulfation by means of concentrated sulfuric acid and roasting at a high temperature. The route yields high rare earth extraction with low iron and thorium extraction and low acid consumption. Rare earth extractions as high as 80 percent were achieved, while iron and thorium extractions were lower than 1 percent, and acid consumption was lower than 0.34 kg of sulfuric acid per kg of ore. The operational window was compared to the one predicted by thermodynamic modeling, with 700 °C representing the optimal roasting temperature.

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

This paper presents the results of an investigation into the effect of pore pressure regime on the factor of safety (FS) and the anticipated critical failure mechanism for a fly ash storage facility. In this study, pore pressure measurements from standpipe piezometers and pore pressure estimated from seepage analysis were used for a comparison of the estimated FS for a fly ash slope. This comparison was applied for static and seismic scenarios. To account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation, a probabilistic analysis was performed. The slope stability analysis was conducted in 2D and 3D, adopting the limit equilibrium analysis approach, and a finite element seepage analysis. The results suggest consistency of failure surfaces for 2D and 3D and an increase in FS values of 5 percent for the 3D approach, limitations of standpipe piezometers. The study demonstrated the sensitivity of the FS value, and the implication of adopting representative material properties, and water table levels, especially in cases where limited data are available, and assumptions need to be made to assess the long-term stability of a fly ash dam facility.

Aug 1, 2024

By Kamran Esmaeili, MINGLIANG TANG

An understanding of the spatial and temporal variations of surface moisture content over a heap leach pad is essential for leaching production and to achieve a high ore recovery. The current leach-pad monitoring and data-collection practice remains highly labor intensive and exposes technical staff to cyanide solution, a hazardous material. To address these challenges, we propose using unmanned aerial vehicles (UAVs) equipped with thermal imaging sensors to remotely obtain image data with high temporal and spatial resolution for monitoring the surface moisture distribution over heap leach pads. A field study was conducted over a sprinkler-irrigated heap leach pad at El Gallo gold mine in Sinaloa, Mexico, and the acquired data were used to generate moisture distribution maps of the heap leach pad’s surface. The created moisture maps provide direct visualizations of surface moisture variation over the surveyed area. Such graphical results are effective tools for inspecting heap-leaching operations.

By Marco Sonnenschein

Belt conveyors for tunnelling are industry standard and key to high performance of TBM drives. Conveyors reduce traffic in the tunnel and increase safety in the tunnelling process. This paper will illustrate the state of the art of tunnel belt applications in very long and curvy tunnels like the Coxwell Bypass Tunnel Project in Toronto, Canada.

Jun 23, 2024

By Greg Beckstrom

Minnesota is a major mining state. This statement is not a dream or stretch goal but is a fact. As reported in a recent edition of Mining Engineering magazine, Minnesota ranks as the third largest state in terms revenues generated from nonfuels mineral production. The vibrancy of the mining sector in Minnesota can be attributed to several factors. The northeastern corner of the state is home to Minnesota?s iron range, one of North America?s largest deposits of iron ore. Iron ore from Minnesota is a strategic resource that has been [ ] instrumental to the nation?s development ? 90 percent of the iron used to build ships and planes during World War II came from Minnesota. Taconite pellets now produced from openpit mines on the iron range are shipped to steel mills worldwide. The growing appetite for steel in China and India has reignited once moribund mining operations throughout the iron range.

Jan 1, 2012

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

6.1 PRINCIPLES OF PLANNING GROUTING OPERATIONS FOR SHAFTS, DRIFTS AND TUNNELS The planning of integrated grouting of vertical, inclined or horizontal underground workings in saturated, fractured rock includes the following phases: 1. Planning for the collection and analysis of geological information concerning the characteristics of the struc¬tural deformation(s) that produced the details of the frac¬ture system being studied. 2. Planning for the acquisition of initial hydrogeological information produced by the flowmetric and hydrody¬namic investigations (described in Chapters 2 and 3). 3. Computing the initial engineering calculations of the ex¬pected or planned dimensions of the isolation curtains for each water-producing stratum (fracture zone) and the expected areal spreading pattern of the grout in each of these water-producing horizons. The selection of the lo¬cations, the initial optimal number of holes and the vol¬ume of grout needed to create each isolation curtain also are included in this phase. 4. The selection or development of a grout formula for the specific hydrogeological conditions that exist at the site. 5. Identification of a resource (deposit) required to produce the grouting clay. The planning of grouting operations must be supported by the acquisition of all necessary initial data, which in¬cludes: 1. The geographic location and administrative responsibil¬ity (ownership and regulatory constraints) of the mineral deposit and any peculiar features of the area where ex¬cavation of the underground workings is planned. The surface relief, the hydrographic network of the region, and the local climatic conditions must be evaluated prior to planning for buildings and waste discharges if any. 2. The economic status of the region, the available trans¬portation, the nature of the energy base, the water and heat supply sources, the location of construction mate¬rials suitable for making the grout all must be deter¬mined. 3. The geological and hydrogeological characterization of the work site must be accomplished. 4. The technical features of the shaft(s) and underground works must be characterized. 5. The organization&apos;s principal initial design plan features and the construction sequence of all buildings and struc¬tures must be developed. These must be correlated with the organization and schedule for excavating the under¬ground works. The technical characterization of a shaft or of other un¬derground workings must contain information about the purpose of the workings, the design depth, the planned excavation procedures along with cross-sections, and the parameters of the lining, if a lining is required. The geology of the section to be penetrated must include geological data obtained from existing exploration activities at the mineral deposit and conclusions about the shaft ex¬cavation conditions obtained from drilling technical moni¬toring holes and exploration drillholes. The interpreted stratigraphic regime, including the thickness, strike and dip of each stratum, must be shown in cross-section. The tec¬tonics, including all geologic structures, must be presented by cross-sections. The bedding orientations must be used to identify anticlines, synclines, monoclines and faults. The lithologic composition and the drillability of the rock com¬prising the section must be examined. The character of the rock&apos;s fracture pattern must be presented. Finally the per¬meability, porosity and storage characteristics of each aqui¬fer must be determined by in situ hydraulic property testing (injection tests or pumping tests, as described in Chapter 3). The fracture pattern of the indurated rock is presented in reports derived from geo-exploration borehole studies and from studies of outcrops on the surface and in all nearby underground workings. The extent of each fracture zone is mapped in three dimensions. The distribution of fracture apertures, the nature of the fractures according to each litho¬logic stratum, and the relationship of bedding planes to each fracture system are all determined. Acoustic logs, downhole cameras, caliper logs, oriented core, and any other appro¬priate geophysical tools available are used to construct the data base for this purpose. The hydrogeological characterization of the geologic section to be penetrated by the workings is based on the analysis of hydrogeological data collected during the drill¬ing and testing of technical monitoring holes and from in¬formation on ground water inflow collected during the ex¬cavation of nearby underground workings, if such workings exist. The hydrogeologic characterization must contain the following information: 1. The identification of all aquifers, their thicknesses and their locations in the section, 2. The distribution of hydrostatic head in the ground water in three dimensions, 3. The coefficient of saturated hydraulic conductivity (per¬ meability) of each aquifer, 4. The porosity and storativity of each aquifer, and 5. The projected rate of water inflow into the shaft, drift or tunnel for each aquifer prior to grouting. This step is used to identify the zones to be grouted.

Jan 1, 1993