Search Documents

By Ernest A. Draeger, James W. Collins

Water only cyclones, sometimes referred to as hydrocyclones, are one of the newest types of coal processing equipment. These devices have achieved wide acceptance as fine coal cleaners in the past decade. Many metallurgical coal plants employ water only cyclones to process 0.5 mm x 0 size coal. Some of these plants have as many as 40 to 50 305-mm-diam units with each unit receiving as much as 9 t/h of raw feed. The growth in the utilization of hydrocyclones is due partly to the energy shortage, partly to the general increase in over-all coal preparation, and also because of a need for a simplified fine coal (0.5 mm x 0 size) gravimetric separator. Large diameter water only cyclones are also available and in use to process feed sizes up to 32 mm in size. However, the size normally employed for cleaning 0.5 mm x 0 coal are 356 mm or 305-mm-diam for single-stage circuits. In two-stage circuits, the secondary units are normally the same diameter as the primary units or smaller, such as 203-mm-diam. By using the small diameter cyclones and treating a closely sized feed, 0.5 mm x 0 only, it has been found that the probable error or imperfection of the water only cyclones is comparable to that obtained on the same size fraction treated in a large 610-mm-diam heavy media cyclone washing 38 mm x 0. The water only cyclone can approach the efficiency of a heavy media cyclone when cleaning fine solids because it creates its own dense media by accumulating high specific gravity particles in the wide angle conical section of the cyclone. A cut-away cross sectional view of a water only cyclone is shown in Fig. 1. It is also true that when treating a wide range of sizes (38 mm x 0) in heavy media cyclones, the smaller size particles (0.5 mm x 0) separate in proportion to the split of the media through the cyclone rather than by particle density.

Jan 8, 1980

By L. Alan Weakly

At a time when the US mining industry is struggling to emerge from a lengthy recession, the burden of new, unnecessary regulations could shorten the life of, or be fatal to many domestic mining companies. The possibility of new restrictions on the use of diesel equipment operating in underground mines is one example of unnecessary regulations. These could cause serious harm to the economic health of many mining companies. Whether future health-related Mine Safety and Health Administration (MSHA) regulations restricting the use of diesel equipment are unnecessary, depends on whether these restrictions are supported by fact or created in a political environment. The mining industry has benefited from the use of diesel equipment in underground metal-non-metal and coal mines for more than 50 years. Since first introduce to underground mines in the early 1940s, the use of diesel equipment has grown in numbers and size. During this time, the mining industry in America has achieved much higher productivity rates and improved safety. Although all these gains cannot be attributed to the greater use of diesel equipment, a high percentage can be. I began my professional mining ca¬reer in 1970 working in the Missouri lead mines. At that time, the use of diesel equipment was well established in metal-non-metal mines throughout the United States and many parts of the world. As director of mining research for St. Joe Minerals Corp. (now The Doe Run Co.), I was involved in research to improve mining productivity and safety. This involved investigating the better and safer use of existing or new mining methods, products, equipment and people. Within this group, diesel equipment had the single largest positive impact.

Jan 1, 1993

By I. E. Lewis, W. R. Hopkins

Flowsheet improvements, such as series/parallel SX plant configurations, discontinuation of plant sumps and improved filter pumping concepts, the use of in-settler baffle systems, and the Krebs and combined mixer-settler designs offer opportunities to reduce SX plant cost. Today's plants employ permanent cathodes and mechanical stripping, and the increased capital cost can be offset by labor savings and higher current densities. The wider use of HDPE and new cell construction materials also reduce capital cost. The "Portelex" type of relocatable design embodies such new, cost-saving measures in a simple basic plant. Organic inventory and losses are reduced by new, fast-settling, hybrid organic reagents with improved kinetics and selectivity.

Jan 1, 1991

The concept of "classification is expanded beyond the performance of the classifying equipment to include all aspects of the fines removal system of the grinding circuit. Design and operating parameters which affect fines removal are identified and discussed, and a quantitative index for circuit fines removal effectiveness is defined. This approach lends new interpretation to certain observed phenomena, and suggests useful guidelines for circuit design and operation.

Jan 1, 1985

By Georgios Bartzas, Vasiliki Karmali, Konstantinos Komnitsas, Anna Kritikaki, Dimitra Vathi, Stylianos Tampouris, Arne Peys

Large volumes of slags, with varying mineralogical and geochemical characteristics, are produced annually by the ferrous and nonferrous metallurgical industry. Most of them are considered as potential secondary resources and may be valorized, following the principles of circular economy, for the recovery of critical elements, including energy transition metals. Apart from the economic benefits, valorization of slags may contribute to the competitiveness of the metal industry and the conservation of natural resources. Valorization also results in minimization of environmental impacts on soils and waters in slag disposal areas, due to the prevention of solubilization and subsequent migration of potentially hazardous elements. The present study utilizes ferronickel (FeNi) slag for the production of alkali-activated materials. The effects of the main experimental parameters, including sodium hydroxide (NaOH) molarity, silica/sodium oxide (SiO2 /Na2O) molar ratio in the activating solution, precuring and curing time, curing temperature and aging period on several properties of the final products, are assessed.

Apr 1, 2025

By Jon Kellar, Samuel Kessinger, Prasoon Diwakar

Tantalum (Ta) and niobium (Nb) are extracted from many different ore types. The major economic orebody mined for tantalum and niobium consists of tantalite ((FeMn)Ta2O5) and columbite ((FeMnNb2O5)) in a solid-solution mineral commonly referred to as “coltan.” The largest supplying region, The Democratic Republic of the Congo (DRC), is unfortunately also the most ethically compromised source for this critical mineral. Officially, the U.S. government has deemed coltan ore from the DRC a “conflict mineral” [1]. The lack of pragmatic and effective local mining regulation in Central Africa, when coupled with high levels of violence and corruption, has spawned a widespread, illegal, unethical and, most importantly, unsafe economy. This illicit economy is centered around first, illegally mining these valuable conflict minerals and second, smuggling these minerals into the global supply chain. Handheld spectroscopy devices could provide further transparency to these opaque supply chains, giving miners, traders and refiners the ability to authenticate the provenance of the minerals they encounter, and allowing companies to prove compliance with the regulatory agencies attempting to curtail illicit mining.

Mar 1, 2025

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES, DAVOOD BAHRAMI

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron and carbon steel), three types of liquids (diesel fuel, hydraulic fluid and engine oil) and four air ventilation speeds (0, 0.5, 1.5 and 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperatures. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Oct 1, 2022

By Michael Day, Paul Kos, Scott Brinton

Quantitative hydrogeologic characterization of fractured rock is challenging because fracture systems are convoluted and difficult to characterize discretely. For large-scale water resource impact analyses, it may be more appropriate to use a watershed water balance approach and analyze fractured systems in terms of “bulk” hydraulic parameters over a large enough scale (hundreds of meters), so that the fractured media may be evaluated as “equivalent” porous media [1]. This is a common investigative methodology for mountain watersheds in fractured bedrock terrain because it does not rely on discrete flow paths but instead evaluates inputs to (recharge) and outputs from (discharge) the ground-water system [2,3]. This paper describes the use of this methodology to perform a practical and cost-effective hydrogeologic characterization and mining impact analysis for a proposed granite quarry in a mountain watershed. The key conclusions of the study guided the mine planning that was designed to minimize impacts to the fractured granite hydrogeologic system and preserve recharge to downgradient sedimentary aquifers.

By Y. Nan

A new computer simulation model for the analysis of underground coal mine production systems in the Peoples Republic of China is presented. As a case study the model was used to analyse the railway system of an existing underground coal mine. Some results of this first application are given in this paper and some conclusions of common interest for underground rail haulage systems are discussed.

Jan 1, 1986

By Yang Ge, Yuzhu Pan, Mansheng Chu, Jue Tang, Cong Feng, Lihua Gao, Zhenggen Liu

Increasing attention is being paid to laterite nickel ore as an alternative to nickel sulfide ore to act as a feedstock for nickel metal production. While laterite nickel ore accounts for a lion’s share of global nickel resources at approximately 72 percent, it accounts for only 42 percent of the world’s nickel production. In addition, the processing of nickel sulfide ore is confronted with enormous challenges due to deeper drilling requirements, higher production costs and depleting reserves. The nickel content in the nickel laterite ore associated with hydrated iron oxides and silicate minerals limits the application of physical beneficiation methods for the removal of iron. Thus, magnetic reduction roasting followed by magnetic separation has been regarded as one of the attractive routes to concentrate and separate the valuable metals from the impurities. 

By Marc Carriere

Bright-orange couplings adorning piping systems are a common sight in just about every underground mine in North America. Grooved mechanical piping, the pipe-joining system that utilizes these couplings, is the preferred method for joining underground and plant piping systems in the mining industry, due to the ease and speed of installation and maintenance. However, the applications for such systems have traditionally excluded high-pressure systems. Most grooved mechanical couplings have a moderate working-pressure limitation, so high-pressure systems have required the use of alternative joining methods, typically heavy-duty flanges. However, the introduction of high-pressure couplings (up to 4,000 psi) has made the grooved joining method viable, and even preferable, for backfill, deep-mine chilled water and dewatering lines and other high-pressure piping applications. As engineers explore the use of high-pressure couplings, questions will undoubtedly arise about the joining method?s capabilities. This article will address the capabilities and specifications of high-pressure couplings, and compare flanged and grooved mechanical pipe joining in traditional as well as high-pressure underground mining applications.

Jan 1, 2011

By Paul D. Tomlingson

Numerous worthwhile benefits accrue to the industrial organization that is supported by a maintenance organization performing at a world class level. That organization will be favored with consistently reliable production equipment. It will be assured of meeting production goals. Its product will exceed marketplace standards. Its customers will see them as a quality organization. Its employees will enjoy job satisfaction and the plant will realize continuing profitability. Every industrial plant aspires to achieve ?world class? status knowing it can compete favorably with the best, most profitable organizations in the world. The trick is to achieve the attributes that qualify your organization for world class status. But there are no world class maintenance organizations. Rather, there are world class industrial organizations that include a world class maintenance organization. Maintenance, by itself, is a service provider, dependent on the support and cooperation of other departments. When that service is exceptional, it is made that way because maintenance is operating in a plant environment that requires it to be exceptional. Managers have created an environment in which maintenance can be exceptional. The plant, mine or facility manager must acknowledge from the start that maintenance is not a stand-alone effort of a plant maintenance department. It will require the joint efforts of all plant departments. Quality material support and full cooperation from operations, for example, are among the essential requisites for effective maintenance and achievement of world class maintenance status. When attributes such as these are reinforced by dedicated plant managers, profitability soon follows.

By SUMANT KUMAR SAMAL, BHAGIRATHA MISHRA, MANOJA KUMAR MOHANTY, SUBASH CHANDRA MISHRA

Steelmaking consumes the majority of chromium and manganese ferroalloys for purposes such as to impart various properties to steel. The quality of ore governs the process kinetics as well as the process economy of the ferroalloy industry. The present study demonstrates the thermal transformation behavior of chromite and manganese ores with varying compositions. Simultaneous thermal analysis (differential thermal analysis/thermogravimetry, DTA/TG) was conducted on these ore samples, where the transformation of mineral phases was correlated with the thermogram characteristics and quantified. Phase, microstructure and compositional analysis results of individual ores corroborated with thermal analysis are in good agreement. Chromite samples are ferruginous with goethite and gibbsite contents, whereas manganese ores vary in composition and also exhibit multiple and/or overlapping transformations.

By David De Lemos Pires

Mining is essentially a materials management process where materials are classified, excavated, moved to a desired location, processed at a cost and sold for a price hopefully to generate a profit. ?How much is that cost and can it be reduced?? is the age-old question. The requirement for a paradigm shift with regard to materials movement in search of low-cost production has not just happened by chance but, rather, has been driven by agents of change that include mining companies, consultants, governments and equipment suppliers. During the past 100 years of mining, surface mining technology has involved humans with hand tools, humans with machinery and unmanned automated equipment. In the past 50 years, surface mining technology has evolved and now takes the form of trucks and loaders (TL), in-pit-crushing conveying (IPCC) and autonomous haulage equipment (AHS).

Dec 1, 2013

By Jacob L. Brinkman, Catherine E. Johnson

Researchers are exploring the use of unmanned aerial vehicles (UAV) to measure concentrations of gas emissions in situations where such measurements are otherwise extremely difficult to obtain, such as NO and NO2 (NOx) emissions from surface mine blasting. Recently, countries have imposed or are planning to impose surface blasting gas pollution regulations, which creates a need for an improved understanding of UAV-based gas measuring systems. The experiments detailed in this paper were performed to determine if airflow generated by the rotors, also known as downwash, unnaturally alters concentration measurements. Downwash turbulence could create locations of varying pressure, which could affect density-based concentrations as measured by some governing entities, including the Occupational Safety and Health Administration (OSHA). 

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jason Navoyski, Jennica L. Bellanca

The paper describes the process of collecting detailed accounts of near-miss incidents and turning them into impactful visual stories using graphic simulation. The aim is to create high-quality training materials to reduce haul-truck-related accidents and fatalities in mining.

Sep 1, 2023

By Emily Dieckman, Claire Kincaid

"When most people think “miner,” they picture an older white man in a dusty shirt and suspenders. He’s holding a gas lamp and a pickaxe, peering at the walls of a dimly lit cavern. This image, while steeped in heritage, is no longer representative of what mining is: a global, increasingly diverse industry.It’s an industry made up of individuals like Zambian-born Chushi Mwewa, PE, president of Southlands Engineering, LLC in the United States and managing director of Southlands Engineering Limited in Zambia; Navajo tribe member Peter Denetclaw, manager of environmental programs and Navajo relations at Freeport-McMoRan; and Chinese and Jewish Alyssa Hom, a project engineer at McCarthy Building Companies.According to the Austrian Federal Ministry of Science, Research and Economics, 168 out of the world’s 195 recognized countries have some mining or mineral resources activity, and the mining industry directly employs more than 25 million people across the globe.However, according to McKinsey & Company’s 2017 “Women in the Workplace” study, white males hold 67 percent of C-Suite positions and 70 percent of senior vice president positions in the corporate world, and mining is no different. This uniformity among leadership has been tied to lower levels of employee engagement, innovation and business growth. The bottom line is this: Diversity is good for business. The question industry leaders must now ask themselves is not “Will we promote diversity?” but “How will we promote diversity efficiently and permanently?”More than 80 industry professionals, consultants and students gathered to discuss this question and share stories at the “Developing Diversity in Mining” workshop organized by the University of Arizona’s Lowell Institute for Mineral Resources (IMR), held during the 2017 SME Arizona Conference in December 2017.Brad Ross, co-director of the IMR and one of the facilitators of the workshop, said he felt diversity was important to discuss because he has witnessed its benefits throughout his career in the mining industry.“By creating a team of people with different experiences and perspectives, a company is better equipped to see the big picture and to creatively tackle problems,” he said. Speakers from industry and academia,including Mwewa, Denetclaw and Hom discussed the challenges surrounding achieving diversity and inclusion as well as the roles and responsibilities of different stakeholders."

Jan 2, 2018

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

This study aims to investigate the reduction thermodynamics of ilmenite and pre-oxidized ilmenite, and reveals the isothermal reduction kinetics of pre-oxidized ilmenite concentrate by carbon monoxide. The results indicate that the ilmenite concentrate and pre-oxidized ilmenite concentrate can be selectively reduced by controlling the temperature. The pre-oxidation process leads to the breakage of complex mineral structure, and the formation of porous simple oxides, which is an effective method to increase the reduction and leaching rate. 

By R. Todd Swinderman

Impact cradles are installed below the belt in conveyor loading zones to cushion the forces from material loading. In this paper, the author will discuss the need for and then explain the new CEMA standard for engineering of impact cradles. He will review the engineering theory and work through an example to demonstrate the assumptions used in the standard do not inappropriately affect the CEMA rating system.

Jan 1, 2002

By Allen G. Taylor

High-value materials, such as gold, platinum and other precious metals, are subject to loss through unauthorized removal from mines, smelters, refiners and other places where such materials are processed. A study by Gastrow (2001) determined that between 1994 and 1998 an average of 603 kg/a (1,330 lb/year) of gold was stolen from South African mines and subsequently recovered. This does not include the gold that was stolen but not recovered. At 2011 prices, 603 kg/a (1,330 lb/year) of gold would be worth approximately $33 million. Mine security personnel believe that the unrecovered stolen gold far exceeds what is recovered (Gastrow 2001). Traditionally, metal detectors have been used to screen personnel leaving secure areas to discourage such unauthorized removal. However, with the current near-record prices of gold, platinum and other precious metals, it has become worthwhile for people exiting a facility to walk out with quantities of product that are too small for ordinary metal detectors to register, resulting in substantial financial losses.

Jan 1, 2012