Search Documents

By D. B. Desai, J. T. Waggoner, J. S. Hill, R. R. Redd, S. J. Klein

The 13 km (8 mile) long Riverside Badlands Tunnel is planned for construction starting in 1998. Extensive geotechnical investigations indicate that the 3.7 m (12 ft) finished diameter tunnel will be excavated through soft ground, weak sedimentary rocks, and heavily fractured metamorphic rocks. Nearly 80 percent of the tunnel will be excavated beneath the groundwater level. Tunneling conditions are expected to range from raveling and over-stressed in the sedimentary rocks, to blocky and seamy/crushed with some squeezing in the metamorphic rocks. Two alluvium reaches will require dewatering. The variable and interspersed ground conditions are expected to be a key factor in selection of tunneling methods, equipment, and initial support.

Jan 1, 1997

By D. A. Huggins

Column flotation is finding increasing use in the flotation of copper, molybdenum and other heavy metals and coal. Columns have proven operational, cost and metallurgical advantages which caused us to investigate their use in the proposed Escondida flowsheet. A comparative pilot plant test with 35 tons of ore showed that one column can replace three stages of cleaning and result in a significantly higher concentrate grade with no loss in recovery.

Jan 1, 1987

By L. Rainey, W. E. Wallace, B. L. Razzaboni, P. Bolsaitis, V. Vallyathan

The hemolytic activity of milligram-sized mineral dust samples from coal mines collected in personal dust samplers were measured by a modified Harington assay method which increases the sensitivity of the technique. Measurements were conducted on a large number of samples from different mines characterized for gravimetric quartz content and the relative bulk concentration of common contaminants (Al,Ca,Fe). The results of these measurements were compared to the hemolytic activity of pure quartz and of mineral samples obtained from roof-bolter dust boxes of two coal mines. No correlation could be established between hemolytic activity and the compositional variables tested. The results suggest that the distribution of minerals among individual particles and the surface characteristics of particles, rather than the bulk concentration, determine the hemolytic activity of respirable mine dusts.

Jan 1, 1991

By LUKAS FAHLE, JURGEN F. BRUNE, ANDREW J. PETRUSKA, ELIZABETH A. HOLLEY, Gabriel Walton

Adverse ground behavior events, such as convergence and ground falls, pose critical risks to underground mine safety and productivity. Today, monitoring of such failures is primarily conducted using legacy techniques with low spatial and temporal resolution while exposing workers to hazardous environments. This study assesses the potential of novel simultaneous localization and mapping (SLAM)-based light detection and ranging (lidar) data quality for rapid, digital and, eventually, autonomous minewide underground geotechnical monitoring. We derive a comprehensive suite of quality metrics based on tests in two underground mines for two state-of-the-art mobile laser scanning (MLS) systems. Our results provide evidence that SLAM-based MLS systems provide data of the quality required to detect geotechnically relevant changes while being significantly more efficient for large mine layouts when compared to traditional static systems. Additionally, we show that SLAM-specific processing can achieve an order of magnitude better relative accuracy relevant for change detection than quality metrics derived from traditionally deployed tests would suggest, while reducing SLAM-drift error by up to 90 percent. In collaboration with an operating block-caving mine, we confirm these capabilities in field tests on a minewide scale and, for the first time, demonstrate methods of rockfall detection using MLS data. While more work is required to investigate optimal collection, processing and utilization of MLS data, we demonstrate its potential to become an effective and widely applicable data source for rapid, accurate and comprehensive geotechnical inspections.

Jan 1, 2023

By Frank T. Wheby, Edward M. Cikanek

A computer performs all logic and computations customarily done by hand in preparation of engineers' estimates or contractors' bids on tunnel-shaft systems. The program described is based on construction methods, work forces and equipment selections corresponding to the current state-of-the-art of rock, soft ground and cut-and-cover tunneling. The program contains logic to permit estimates of cost of complicated tunnel-shaft systems; it is not necessary to input quantities, as the program calculates those from the tunnel design that is internally generated. In any estimate, the program bases its cost computation on user-input requirements and site conditions, such as tunnel shape and size, shaft depth, ground characteristics, construction methods, and other factors. To provide great flexibility, the user of the program is provided with options for accepting designs built into the program or overriding these designs by his own inputs. An illustrative example is presented.

Jan 1, 1974

By Flavio Moreira Ferreira

In mining industry, one of the simplest methods to smooth the standard deviation of a given ore controlled property is to build longitudinal blending piles. The effect of homogeneization is obtained due to the fact that an entire cross-section of the pile is reclaimed at each time. The variance of the pile output is the sum of the internal cross-section slice variance plus the reclaimed slice variance. While the first term is a tipical short-term parameter and is absorbed by the process, the second one may be or may not be absorbed. The goal of designing blending piles is to minimize the reclaimed slice variance. Conditional Simulation as described in this paper, is an alternative method to do it. It is devised to design longitudinal blending piles, taking into consideration economical, geometrical and statistical parameters of the ore to be blended, in order to estimate the resulting effect. It presents advantages in relation to other methods for its adaptability and flexibility in simulating pile performances.

Jan 1, 1992

By Don Muraoka

Soda ash, anhydrous sodium carbonate, is produced from underground trona deposits occurring in the Green River Sasin of Southwestern Wyoming. Stauffer Chemical Company of Wyoming, a jointly owned subsidiary of Stauffer Chemical Company and Rocky Mountain Energy Company mines the trona and processes it into high-purity soda ash. Stauffer Wyoming has been in operation since 1962 with a current production capacity of approximately 2.2 million tonnes (2 million short tons) per year of soda ash. The Refinery has five parallel operating trains utilizing the monohydrate process which is a series of chemical processing unit operations described below. Screening and Crushing the Trona The mined trona is brought to the surface in two counterbalancing ore skips. The ore is initially screened with Refinery feed, less than peagravel size material, entering the process while the oversize is conveyed to an outdoor stockpile.

Jan 1, 1984

By M. B. Thorpe

Land use and access to land are limiting factors in economic development in the Western region of Ghana. Mining uses land during operations and then rehabilitates the land as part of ongoing operations and closure. Golden Star Resources Limited (GSR) aims to contribute to the sustainability of the local economy during its operations and then post-closure. Following a series of alternative livelihood initiatives, GSR reviewed the success of these programs and decided to focus on an oil palm project that uses out-growers to reach the local economy. The project started using small holdings that were individually managed. However, the ongoing effects were limited. Following a review of the options, the Golden Star Oil Palm Project was started using land committed to the pro-gram by the Bogoso Mine. The initial program covered 275 ha with over 40,000 trees with 300 people involved in the development. The Traditional Authorities have committed additional lands to the project to a planned total area of 18,000 ha.

Jan 1, 2007

By S. C. Brown, R. C. G. Oliveira

Surface wettability, or contact angle, dictates a number of multiphase ensemble interactions that influence particulate dispersability and adhesion behavior (e.g., filler compatibility] in addition to a number of other phenomena including biocompatibility and bulk powder segregation. The wettability of particulate surfaces significantly impacts nearly all process industries; however, the available techniques to access this quantity are either relative, or tedious-and are application or industry specific. In this study, key features of existing techniques have been combined to design an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.

Jan 1, 2003

By Jerry M. Whiting, Landy A. Stinnett

The subject of this paper is broad and complex. Secondly, it is near and dear to the authors' hearts. Therefore, it doesn't seem possible to deal with every aspect of it in less space than a good size textbook. Also, if we dealt with all of the basics of feasibility studies and report preparation, we would cover a lot of material available in the literature, and would have to minimize our editorial comments. In view of these limiting realities, we have chosen to discuss selected facets of the subject, and to provide several comments which stem from our personal experiences during the past 20 years. "Think Ahead" hen someone is undergoing training to command a large ship, the following short phrase is engraved in his memory: "Think Ahead." The reason is simple enough. A battleship, aircraft carrier or oil tanker cannot change directions quickly, and if one waits to a what the other ship is going to do, there may be twisted metal and bodies scattered all over the ocean floor. The commanding officer has to use radar, forward rind aft lookouts, experience, common sense, intuition, weather forecasts, and everything else available to him to avoid trouble. Remember the USS Stark, and the fate of its captain? The fact the Stark was hit by a "friendly" missile didn't lessen the damage. How about running into a mine? Is it an excuse that no one thought about the possibility of a minefield ahead of the ship? The point is, relative to feasibility studies, that its prospective authors, and especially the commander of the efforts required to create it, must "think ahead" from the moment of their association with 4 mining activity. They must

Jan 1, 1987

By D. Gu

Breakage of rock by machine is one of the major methods of excavation. With the development of modern engineering techniques, the advantages of using this method have become even greater. Improving efficiency and reducing the cost of rock breakage is the main goal of mechanizing the rock-breaking operation. For a given stratum, the efficiency of a machine excavation depends, to a large extent, on the design and method of application of the tools used. In a planetary cutter head, the subcutter heads move like planets around the main drive shaft. The general structure of the cutter head is shown in Fig. 1. As shown in this illustration, the main drive shaft (1-1) is connected to the tie bar (1) and, thereby, to a gear(5) that meshes with a fixed-gear ring(2). The subcutter head (4) is rigidly connected to the gear (5) by the subcutter-head axis (2-2). When the main drive shaft (1-1) rotates, the subcutter head (4) rotates around the axis (2-2), under the action of the tie bar and with the help of sleeve pipe (3).At the same time, axis (2-2) also rotates around the main shaft (1-1). As shown in Fig 1, is the angle between the main shaft and the subcutter-head axis.

Jan 1, 1995

By B. Govindarajan, T. C. Rao, J. P. Barnwal

A simple modelling methodology has been proposed to predict the performance of industrial coal flotation circuit based on the observations made on the actual performance. The solid content in the tailings of the coal flotation circuit has been identified as a lode-star to predict the performance in terms of yield and ash content of the concentrate. The modelling parameters are directly measurable.

Jan 1, 1995

By Sandra L. Maxfield, Alan Mair

Strategic design of groundwater monitoring programs can increase public confidence in mine management, decrease financial assurance requirements, and minimize environmental budgets. Monitoring of inorganics is challenging because many occur naturally with baseline concentrations fluctuating spatially or temporally. Evaluating monitoring data to distinguish between a hazardous release or a natural fluctuation in baseline concentration can be controversial. In order to develop an effective program, monitoring parameters should be selected which are mobile and stable. Statistical procedures should be customized to address the uniqueness of groundwater systems. Calculated baseline concentrations should minimize the false negative & false positive rate.

Jan 1, 1995

By F. F. Aplan

Rather than reiterate what is well known about the flotation of the non-sulfide minerals, emphasis has been placed on those separations which are not so effective. These difficult separations are largely connected with problems of selectivity in the flotation of the base metal oxides, the other slightly soluble minerals, the insoluble oxides and the naturally floatable minerals. The paper discusses possible methods of improving selectivity between similar species and of improving selectivity against the gangue minerals.

Jan 1, 1994

By Ernest Peters

To model the zinc pressure leach, equations have been written that describe the rates of individual reactions taking place, including (a) oxygen mass transfer, (b) ferrous oxidation by dissolved oxygen, and (c) ferric reactions with ZnS and other minerals. In the continuous process, at steady-state, these take place at the same rate, and so the equations can be solved simultaneously. Model calculations using simultaneous equations are shown in graphical form to demonstrate the effect of different variables on the leach performance.

Jan 1, 1993

By Ted M. Noskiewicz, James A. Ramsay

INTRODUCTION During the various stages of an underground project from inception through design and construction, probably the single factor of most interest and concern is the nature of the ground. The ground conditions more than any other item govern costs and feasibility; and although the methods available for assessing the ground have become increasingly reliable during the past thirty years, it is still very difficult in many cases to predict the behaviour of soil and rock during and after excavation. To help in this ground evaluation process, we have frequently supplemented the boring program with one or more large diameter inspection holes; and during the past eighteen years, seventeen of these holes have been constructed on tunnel projects which we have designed. There are references in the literature to similar inspection holes (1); however, as far as we are aware, no detailed description of them has been published. The behaviour of soil or rock during and after excavation and the effect of ground water on tunneling operations are of vital interest to tunnel designers and contractors. A comprehensive geotechnical investigation is therefore among the early and most important tasks carried out on a tunnel project and the backbone of every geotechnical investigation is the boring program. A series of borings, typically 50 to 100 mm (21 to 4 in) diameter, are drilled from which soil samples or rock core are recovered and the ground water observed.

Jan 1, 1979

By M. Georgescu

In the framework of the rapid development of contemporary society, the use of underground space represents an emerging opportunity because it can contribute to decreasing pressure of occupation of ground space while in the same time it can increase the economic value of the useful mineral substances, also through underground establishment of dangerous surface activities, contributing thus in environmental protection. This paper underlines the most important benefits of underground space utilization with the objective the exploit the potential of this real resource.

Jan 1, 2006

By K. Eric Livo

The Front Range Infrastructure Resources Project (FRIRP) of the U.S. Geological Survey (USGS) is currently using Landsat Thematic Mapper? and air- borne-visible-infrared-imaging-spectrometer (AVIRIS) data along with planned thermal-infrared data and interferometry-synthetic-aperture radar (IFSAR) data to assess the industrial-minerals quality and quantity along the Colorado-Wyoming Front Range Urban Corridor and to characterize surrounding areas. Landsat? satellite data show synoptic views of the corridor, which may readily be used to identify potential regions of permissible terrain, such as river drain-ages, pediment surfaces, upturned lithology, and bed- rock exposures, where various types of deposits may occur. Descriptive models of these deposit types are used to define the physical features that need to be recognized and characterized. In the case of Landsat? data, the measured light is either reflected or partly absorbed by surface materials, depending on the wave- length of the light, which allows coarse mineral classifications to be made.

Jan 1, 1999

By Darryl Amick, Keith A. Prisbrey, Lee E. Plansky

The problem addressed was to develop automated image analysis of metal welds to replace unreliable and costly 100% visual inspection. The objective was to evaluate neural networks combined with features from gray level surfaces. Photomicrographs of the welded seam in Zircaloy-4 channels used in nuclear fuel rod assemblies were examined. The methodology used was to select a set of morphological feature coefficients from Bessel Fourier morphological feature coefficients extracted from digitized photomicrographs. The selected morphological feature coefficients were then used to train a neural network. The approach was verified initially by successfully training a neural network using the known, secondary chemistry of the alloy welds. The results were good. The Bessel Fourier coefficients captured sufficient information from the metallographic images to distinguish weld quality. This approach has the combined advantages of compressing the images through Bessel Fourier coefficients and give the ability to rapidly process large amounts of data using neural networks.

Jan 1, 1993

By Chaoxun Zhao, TAIYOU LI, JIAQI JIN, Chen-Luh Lin, Jan D. Miller

A large portion of the energy consumed in copper concentrators is used to reduce the particle size of the feed by crushing and grinding. The cost of metal production could be reduced if low-grade particles of centimeter size were removed prior to further processing. Two copper sulfide ore samples (3 × 1 cm) from Arizona were analyzed by micro X-ray computed tomography (Micro-XCT) to determine the grade of copper sulfide in each particle. For copper ore sample A, a significant number of particles contained very low amounts of copper, while some particles had copper sulfide grains of millimeter size. Based on Micro-XCT, it was expected that 85 percent of copper for sample A could be recovered at 65 percent of mass rejection during preconcentration by sorting. However, in sample B (a different copper ore), distribution of copper sulfide was dispersed primarily in each ore particle, so for the particle size class of 3 × 1 cm, liberation of copper sulfide and gangue minerals was not significant. In view of the XCT results, dual-energy X-ray radiography was used as a basis for sorting. Pilot-scale X-ray sorting of sample A (10 × 1 cm) showed 31 percent rejection of a 0.08 percent Cu gangue product with a corresponding recovery of 90 percent copper.