Search Documents

By RICKARD HANSEN

With vehicles frequently found in mines and tires being a major fuel item, the risk of tire fires will be severe underground. This study presents an analysis of tire fires on mining vehicles to increase the knowledge of the risk and mitigating measures, which would improve the fire safety underground. Data from fire experiments and computational fluid dynamics (CFD) simulations were applied. It was found that the wheelhouse of a loader caused an increase in the flame tilt angle, decreasing the flame impingement and heat flux downstream. The flame temperature of a drilling rig tire was found to be higher than that of a loader tire, increasing the risk of igniting items. The construction of the wheelhouse/mudguard will contribute to a longer flame length by creating a fuel-rich environment. The CFD simulations predicted higher flame tilt angles for a drilling rig for higher flow velocities, indicating the influence of the wheelhouse/mudguard construction and tire geometry on the flame tilt angle. The construction of a loader resulted in flow behavior, where the short distance to the front mudguard/tire and the separation of flow directly downstream of the construction led to gases being steered past the front mudguard/tire. In a drilling rig case, the longer distance to the front mudguard/tire led to gases being directed toward the body of the vehicle after passing the area with flow separation.

By Francois E. Heuze

We demonstrate a new capability to analyze the behavior of circular shafts in jointed rock. This was made possible by the development of a new, axisymmetric, joint finite element (2). Whereas the only previously reported such element was singular (1) and inadequate at some orientations, the current element has been extensively validated (3). The need for including discontinuities in a shaft analysis comes from two sources. First, the various rock formations may have discrete jointing, bed- ding, and interface between them. Second, there is a joint at the boundary between a concrete liner and the rock, and possibly between the various segments of the concrete liner. To demonstrate the applicability of the new model, we analyze a vertical circular shaft 5.4 m in diameter, in a series of horizontally bedded sandstones and siltstones. The shaft excavation is followed through three initial steps: 6 m, 15 m and 24 m deep.

Jan 1, 1979

By Ihsan Berk Tulu, Deniz Tuncay, DYKE MARK ALEXANDER VAN, Ted M. Klemetti

Bleeder entries are critically important to longwall mining for the moving of supplies and miners as well as the dilution of mine air contaminants and must stay open for many years. In this study, standing supports in moderate cover bleeder entries were observed, numerically modeled and instrumented by researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH). The measurements of the installed borehole pressure cells (BPCs), standing support load cells and convergence meters, and roof extensometers are presented in addition to the numerical modeling results and visual observations made by the NIOSH researchers in the bleeder entries. The results include the effects of multiple panels being extracted in close proximity to the instrumented site as well as over one and a half years of aging. As expected, standing supports closer to the longwall gob showed the greatest load and convergence. The roof sag appeared generally independent of the proximity to the longwall gob. The BPC readings were driven by both the proximity to the gob and the depth into the pillar. The results of this study demonstrated that the entry roof can respond independently of the pillar and standing support loading. In addition, the rear abutment stress experienced by this bleeder entry design was minimal. The closer the mine development, pillar or supports are to the gob, the greater the applied load due to rear abutment stress.

By D. W. Scott

Ontario has a diverse industrial mineral resource base including abundant resources of structural industrial minerals such as sand and gravel, crushed stone, building stone, clay, shale, limestone and dolostone. These resources are used in the production of aggregates, brick, metallurgical stone, fillers, lime, cement and other construction materials. The majority of the operations are in deposits of Paleozoic and Quaternary age in southern Ontario, close to the major markets. Province-wide, there were over 140 million metric tonnes of aggregates produced in 1985, approximately 115 million tonnes of which was produced in southern Ontario with the remainder being largely from Crown land in northern Ontario. The structural industrial minerals account for over 80% of the value of total industrial mineral production, with the remaining 20% of the value king accounted for by the non-structural minerals being led by salt which is produced in southwestern Ontario. A host of other non-structural industrial minerals are known but production is currently restricted to calcite, gypsum, quartz, talc, nepheline syenite and by-product metallurgical sulphur products (Fig. 1). Location and Market Area Major production is in the area closest to the large markets of urbanized southern Ontario and the northeastern and north-central United States. In general, with the abundant variety and widespread resources of industrial minerals and the large population within 400 miles of most deposits, the market offers great potential. Ontario's 9 million population accounts for about 35% of the entire gross domestic product of Canada of $476.361 billion dollars in 1985. This equates to about 113 of the nation's buying power being within a 200 km (125 miles) radius of Toronto. This major concentration of industrial and economic activity has resulted in a well developed industrial minerals industry fulfilling most of the structural industrial minerals demand in Ontario, as well as a subsidiary demand in neighbouring provinces and states.

Jan 1, 1987

By Carter Brown, Kate Brown Requist, Eric Lutz, Moe Momayez, Athira Satheesh

New mining health and safety training modalities are becoming increasingly prevalent in the underground mining industry. Various digital training tools have been developed over the past several years, but the extent of their use remains unclear. Advances in gamified training by way of computerbased video games and virtual reality (VR) have opened a new avenue for mine rescue and self-escape training, but these methods have not been widely adopted across the mining industry. Mine rescue and self-escape situations require a mix of in-classroom training as well as live drills, but it is important to assess the extent of and effectiveness of new training modalities. The Mine Rescue and Self-Escape Survey (MRSES) was distributed to underground mining operations to collect perceptions of current training effectiveness as well as willingness to adopt new training methods as a complement to live rescue drills. Responses from the MRSES indicate that adoption of digital training technologies has been slow-going despite an interest in their use. Further, there appears to be no meaningful connection between more frequent escape and rescue training and feelings of emergency preparedness. With relatively little use of already developed digital training tools but an interest in their adoption, it may be time to reassess current emergency preparedness training philosophies.

May 1, 2025

By S. Monette, D. B. Dreisinger, D. Vleeschhouwer, G. B. Harris, G. A. Kordosky

A new process for the recovery of pure (>99.95%) palladium and platinum is described. The process, which has been tested at the pilot scale, comprises (i) the simultaneous solvent extraction of palladium and platinum by a new Schering Berlin reagent, TN 1911, (ii) washing of the loaded extractant to remove co- extracted impurities, and (iii) differential stripping of first platinum at pH 3, and secondly palladium with strong hydrochloric acid, and (iv) precipitation of palladium and platinum salts, followed by reduction to metal. The process is, unusually, a non-ammonia one requiring only small amounts of ammonia at the end where final purification may be necessary for particularly complex feed solutions.

Jan 1, 1993

By Larry Snyder, Levent Ozdemir, Charles Fishman, Fun-Den Wang

Tunnel Boring Machine Instrumentation A 9.17 m. diameter tunnel boring machine presently in operation in Chicago, Illinois, has been instrumented to continuously monitor and record machine thrust, torque and penetration rate during boring. A micro-processor-based data logger capable of monitoring up to 60 channels of data digitizes and converts into appropriate engineering units the signals from various transducers mounted on the machine. The output from the data logger is sent to a teleprinter, providing a permanent record of measured data. The program control enables the data logger to scan all data channels at desired time intervals. Data obtained to date have been analyzed to determine the interrelationships of the parameters measured. Penetration rate was found to increase linearly with machine thrust with a unit increase in thrust causing more than a unit increase in penetration rate. For low thrust levels corresponding to the initial stages of a boring cycle, the penetration rate was observed to behave erratically until the thrust pressure was sufficiently high for the cutters to establish full contact with the tunnel face. Torque showed a curvilinear increase with machine thrust, reaching the design rating at about 70% of maximum available thrust. No-load torque was approximately 20% of the machine's rated torque capacity. Overall, the trends observed in measured machine parameters correlated closely with those predicted from experimental and theoretical boreability studies. In summary, the instrumentation system has mett two basic goals. First, it provided extensive and accurate boring data and secondly, it has proven that an automatic data acquisition system can be installed on a TBM and can function under adverse environment.

Jan 1, 1979

By Scott G. Britton

Up to now, the hands-on approach to construction has been stressed. This chapter reviews the basic tools available for construction design and monitoring of a construction project. It is divided into three discussions, all under the general title of computer aids, since the trend for using these tools-is via the computer. In the context of our discussions, the focus for computer aids will be on the use of evaluation and analysis techniques for coal mine construction applications, including mainframe programs, CPM techniques, as well as mini and microcomputer applications. Although the presentation of material in this chapter may be detailed at times, by no means does it cover the entire field of computer applications for design or project scheduling and monitoring. It is only an attempt to illustrate the possibilities that are available to construction and mine engineers. Interested persons can pursue computer applications for coal mining by reviewing Computer Methods for the 80's. by Alfred Weiss, editor, published by SME-AIME.

Jan 1, 1983

By R. Frenette, A. W. Mo, H. A. Hamza

Fine particles present major technical and economic problems to those who deal with solid/liquid separation processes. In the coal industry the problem is compounded by the large amounts of produced fines such as those present in Western Canadian coals. Flocculants in the form of high molecular weight water soluble polymers are commonly considered an effective solution for the enhancement of the separation process. These reagents are relatively expensive especially when considering a low-price commodity such as coal. Optimization of the use of these reagents is therefore an operational necessity. Six polymers were evaluated as to their effectiveness in flocculating a fine coal tailing. Results were compared with those for a reference flocculant, in-use at that time in the washery. It was shown that, in general, flocculants significantly improve the solid/liquid separation process. The ranking of the flocculants as to their effectiveness in settling and filtration indicated that the best flocculants for settling were not necessarily the most effective for filtration. Flocculants that showed the best filtration improvement were generally cationic and those best for settling were anionic.

Jan 1, 1988

By Harold Bloom

Dimethylglyoxime reacts with nickel in a buffered ammonical-citrate solution containing the detergent ?Aquet? and hyroxylamine-hydrochloride. The resulting nickelous dimethylglyoxime is extracted with xylene. Visual comparison with standards permits the estimation of from 50 to 10,000 ppm of nickel. Soil, rock, or sediment may be decomposed by digestion with (1-3) nitric acid, allowing about 70 determinations per man-day to be carried out. With minor modifications to the above procedure, sediment and soil may be semi-quantitatively analyzed for nickel at the sample site. The chemical equipment is easily portable and the analysis extremely rapid because the buffer, dime thylglyoxime and xylene are added simultaneously to the sample and no heating is required. The sensitivity varies with the "availability" of the nickel ions; under favorable conditions, one may obtain a positive test for as little as 10 micrograms in soils and sediments. This procedure is similar to one, for the field determination of heavy metals described elsewhere by the author.

Jan 1, 1958

By R. Y. Wan, J. D. Miller

Thiohydrometallurgical systems including thiosulfate, thiocyanate and thiourea have been stud- ied as alternative liriviants for the leaching of gold. Research and development of thiohydrometallurgical technology has been prompted by environmental concerns with the use of cyanide and problems associated with the processing of difficult-to-treat ores. These thiosystems have some chemical similarities, enabling gold to be leached in a practical oxidizing environment. However, the solution chemistry of the thiosystems is complicated due to instability of the thioreagents and many other reactions which occur during the gold leaching reaction. In this paper, interference reactions of selected metal ions and sulfide minerals are examined in order to understand important aspects of solution chemistry which control the stability of the thioleaching reactions. Applications using thioreagents as lixiviants for oxide and refractory gold ores are presented.

Jan 1, 2005

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Square-set timbering of stopes developed from stull support methods because veins too wide for stulling were being mined. In general, the void caused by the stoping of the ore is filled with a system of interlocking timbers. Timber framework supports the wall rock, the mining operations, and provides access. A timbered stoping method can be used in all widths of veins at any dip. The timbering can be normal and parallel to the planes of the walls or at angles to these planes. Irregularly shaped ore bodies can be worked by timbered methods. Pinching or swelling of the vein will not adversely affect the method. Timbered stoping is especially advanta¬geous where weak ground is encountered in the vein or the wall rock. The ground is unsupported only until timber sets are stood. These stopes can be filled with sand or waste when desirable. The customary method of developing a square-set timbered stope with haulage drifts above and below and timbered raises on each endline is shown in Fig. 1. The drifts are timbered the full stoping length. The raises have two compartments with the manway and timber slide in one compartment and the chute in the other. The drifts and the raises cannot be widely spaced as handling timbers is an important consideration. Stoping can begin immediately above the drift timber and continue in both directions and upward from the raise. Breasting down each blast round for only one timber set laterally is the common practice. The blasted ore falls to a lower floor where it is slushed or trammed to the chute. Drilling can proceed on the upper floor while broken ore is being removed from the stope. As shown in Fig. 2, square-set timbering may be used in cut-and-fill stopes to support the back and walls until fill is added. There are various ways of developing an ore block for timbered stoping. Fig. 3 depicts the situation for the main haulage in the vein with an intermediate drift separated from it by a sill pillar. The ore is slushed into the chute connecting the two drifts. The situation in Fig. 4 is identical to that in Fig. 3 except that no sill pillar is used. In Fig. 5, the haulage drift development is done in the footwall with crosscuts driven to intersect the ore body. The intermediate drift development is above the crosscuts with a minimal sill pillar. The main bottleneck in timbered stoping is in the timbering process. Drilling in the stope is generally held up while timbering is done. Two or three men are re¬quired to do the timbering and an additional one or two men are needed to transport and raise or lower the tim¬ber. Good organization is essential to timbering. Skill must be exercised in standing the timber to support the ground and still maintain good production. COSTS AND PRODUCTIVITIES Development and stoping costs are presented in Tables 1 through 7 for the situations in Figs. 3 and 5,

Jan 1, 1982

By Glenn A. Gruber

The conditioning of phosphate flotation feed with anionic flotation reagents was identified as a high- priority research topic during a beneficiation work- shop sponsored by the Florida Institute of Phosphate Research (FIPR). FIPR subsequently solicited research proposals to identify the mechanisms of reagent adsorption, to determine scale-up relationships for conditioner design, and to investigate the effect of conditioning variables on reagent adsorption and flotation performance. The two-year research project was awarded to Jacobs Engineering. Somasundaran, Inc., the University of Florida Mineral Resources Research Center, and the U.S. Bureau of Mines assisted Jacobs. Two mechanisms of anionic collector adsorption were detected by spectrographic analyses and confirmed by microcalorimetric measurements. The mechanisms provided a sound technical basis for the empirical practice of conditioning phosphate flotation feed at a high percent solids. Tests performed in laboratory and pilot-scale agitated tanks indicated that power intensity may be used as a reliable scale-up parameter for anionic conditioning of phosphate slurry. Excessive agitator speed during conditioning was found to be detrimental to anionic flotation performance. Some dimensional ratios of anionic conditioners were found to be consistent with good utilization of agitation energy. Laboratory conditioning and flotation tests demonstrated that adsorption of collector onto phosphate and the subsequent recovery of phosphate in anionic flotation were significantly influenced by the quantity and quality of water used in conditioning. Conversely, the quality of water used in flotation was more influential on the recovery of quartz in the concentrate. A comprehensive survey of anionic conditioners and conditioning practice in the Florida phosphate industry was also performed during this project. The study clearly showed that flotation testing with laboratory conditions typical of scientific research gives different results than laboratory testing with simulated plant conditions. The effects of test conditions on laboratory test results should be carefully considered by investigators planning and conducting applied research.

Jan 1, 1999

By Edgardo I. Cifuentes, Andrew L. Mular, Andrew Burkert

Experimental designs are data acquisition plans which, if followed exactly, will quickly provide process engineers with information to assess statistically the individual and joint influence of factors on responses to permit of rapid decision making. Methodology employed to construct data acquisition plans is described in some detail. In production environments, factorial designs are appropriate for most purposes. Use of two level factorials to make decisions is described for a grinding circuit.

Jan 1, 1991

By Alfred Jr. Petrick

Modelling of cash flows and calculation of net present value of rate of return over the expected life of a mine/processing unit continues to be the accepted basis for mineral investment decision-making. The computer and spreadsheet programs have greatly improved ability to perform sensitivity and risk analysis, hence our ability to deal with key analytical problems. These problems of cash flow analysis result from the necessity of forecasting an uncertain and risky future. Cash flow models begin with the critical assumption of a "design basis", then integrate all of the variables relevant to the investment decision including forecasts of price, cost, taxation, financial conditions, and company strategy. Alternate "scenarios" portray possible future outcome of the investment decision. The potential for straying from reality is enormous. The computer has eliminated the time consuming hand calculations from the cash flow analysis, but the analyst still struggles with the risk of trying to predict "how the project will really turn out".

Jan 1, 1991

By Mark E. White, John H. McCowan, Michael C. Costello

Minproc Engineers has carried out the design construction and commissioning of thirty two process plants in the period 1978-87. Twenty eight are gold silver recovery plants, and of these twenty two were gold alone and six were gold and silver. In most plants carbon was used for gold adsorption. Desorption has been carried out using the USBM Homestake method, the Anglo American Research Laboratories method, and the Micron Methanol method. Electrowinning has utilised steel wool, stainless steel wool, and aluminium cathodes. Electrorefining using polished stainless steel cathodes is practised. This paper summarises the experience gained in these operations

Jan 1, 1987

By J. M. Rotter, R. A. Lohnes, J. Y. Ooi

Reliable prediction of wall pressures in a coal silo demands careful characterization of the stress-strain properties of the coal. This paper describes the results of triaxial compression tests on a typical fine-ground coal used in power generation and describes the fitting of several different constitutive models to the data. The fitted parameters for the constitutive models are well suited to application infinite element analyses. The different models are used to give the reader flexibility in choosing a model and to show the shortcomings of some models. To explore the quality of the fitting process, the fitted results are compared with finite element predictions of the triaxial test itself.

Jan 1, 1998

By DING TANG, JINGHE CHEN, Shuiping Zhong, CHEN KUANG

The Zijinshan gold-copper mine, located in Shanghang County, China, is a porphyry-type, low-grade ore deposit with a geological profile of upper gold and lower copper. Despite its low-grade nature, it has become one of the largest in production scale and most profitable nonferrous metal mines in China, which can be attributed to the successful application of hydrometallurgy as well as proper engineering design. A large-scale, open-air cyanide heap leach has been successfully implemented to recover gold under the humid and rainy weather conditions of southern China. Furthermore, according to the gold ore characteristics, a combination of gravity separation, carbon-in-leach and heap leaching processes was developed to improve gold recovery. In terms of copper extraction, copper ore of a grade higher than 0.25 percent is fed to the flotation plants to produce copper concentrate (gold is also enriched here), while copper ore of a grade lower than 0.25 percent undergoes heap bioleaching followed by solvent extraction and electrowinning to produce cathode copper. Additionally, a unique bioleaching system has been established at the Zijinshan Mine: low operating pH (0.8~1.0), high concentration of total soluble iron (~50 g/L), high temperatures (45~60 °C) and low activity of microorganism (~104/mL) in the pregnant leach solution (PLS). This review paper summarizes the practical experience acquired in developing the Zijinshan gold-copper mine and could be of use in other gold and/or copper plants.

By Richard W. Brummett

Problems in new strip mine development is a subject that could require several days to cover adequately. Coupled with the fertile imagination of television writers, we could probably expand it into a series rivaling Gunsmoke in longevity with just as many shootouts at sundown. It would-of course-be subject to a high Neilson Rating. To bring the subject into perspective, we will limit the comments to a general discussion covering western strip coal developments. Stimulated by increased demand for low sulfur coal, surface mineable western coal operations began a shift into high gear approximately four years ago. Then came last year's "energy crisis" that increased the pressure on coal development not only in the west, but nationwide. Several eastern power plants having dual oil and coal burning facilities were directed to discontinue using oil. Also, a number of new south and southwestern power plants scheduled to burn natural gas or of I commenced an ordered conversion to other fuels, namely, coal. The involved utilities with reserve positions accelerated their planning while others began the search for long-term commitments from coal producing companies. In addition, announcements were made for proposed mine mouth coal gasification projects in New Mexico, Wyoming, and North Dakota.

Jan 1, 1974

By Caren Caldwell, Leslie Thompson

1.1 Biological Process Description Pintail Systems, Inc. (PSI) has developed and in partnership with their clients in the mining industry has applied biological remediation processes for detoxification of spent ore and process solutions from heap leach operations. Contaminants that are treated to mine closure levels or drinking water standards include cyanides (weak acid dissociable and total cyanides), thiocyanate, nitrates and heavy metals. Biological processes are both site-specific and ore-specific processes. PSI specializes in isolating indigenous microorgan­isms from spent ore and process solutions and augments them in the laboratory for enhanced bio-detoxification in the field. Bioaugmentation in the lab is a key to successful heap bio-detox in the field. In PSI's bioaugmentation processes native microorganisms are isolated from the spent ore environment and are tested for contaminant remediation capacity. A majority of the indigenous microbes will be tolerant of the spent ore environment but will not contribute to contaminant metabolism. Indigenous enrichment or biostimulation of these non-working microbes by adding trace nutrients can competitively inhibit the working microbes. For this reason PSI focuses on the bioaugmentation process where non-working microbes are discarded and the working population is enhanced through stress, mutation and exogenous enrichment before it is re-introduced to the heap and process solutions.

Jan 1, 1997