Search Documents

By Robert P. Moodry

It was attempted to revitalize an old sulfide leach dump by increasing the oxygen content within the dump. Compressed air was introduced into the old dump. This was accomplished by drilling 300 foot angle holes into the dump surface with an Aardvark drill which holes are then cased with 1-1/2 inch perforated PVC pipe. Compressed air is injected through these cased holes during a 10 day rest cycle. The second case consists of bedding perforated polyethylene pipe at the interface between the old dump surface and the next Lift of a new dump. Compressed air is then blown through the bedded perforated pipe on a continuous basis while leach solution is applied.

Jan 1, 1976

By George E. Williamson, Mikiya Higuchi, Michael T. Traylor

Extensive soil conditioning was required to allow Earth Pressure Balance(EPB) tunneling on the South Bay Ocean Outfall tunnel project in San Diego, California, near the Mexican border. This tunnel extends 19,000 feet out under the Pacific Ocean and was mined through soil formations including silts, sands, gravels, cobbles, and boulders. EPB pressures ranged from 3.0 to 7.0 bar, with the maximum pressures required when mining through the highly permeable granular formations.

Jan 1, 1999

By M. Deniz Turan, HASAN NIZAMOGLU, MÜCEVHER TURAN, RAMAZAN ORHAN

Tailings, or flotation waste, formed during copper production may be considered in the class of valuable wastes because of the amount of copper they contain. With the decreasing grade values of copper ores, the utilization of wastes like tailings that carry certain amounts of copper as secondary sources has become a necessity in both the economic and environmental senses. This study was carried out with the aim of using ammonium derivatives for the recovery of copper from tailings waste produced during copper production and utilizing their complex formation characteristics. In the conditions of six hours of leaching at 30 °C in the presence of 22.5 percent ammonium hydroxide and 100 g/L ammonium persulfate, 91.47 percent of the copper was transferred into the solution, while iron was not transferred, indicating that copper can be selectively recovered from tailings.

By John A. Cordes, Thomas F. Torries

INTRODUCTION Nonfuel mineral markets have always tended to be volatile due to the cyclical nature of demand and the difficulty of fine-tuning capacity and output levels. Experiences over the past two decades, however, have been especially perverse. This short volume attempts to provide insights into this era and some guidance for the future. The papers are linked together by their focus on issues of productive capacity. At the same time, they provide a useful description, explanation and evaluation of the industry's evolution and its implications for the near-term. The regnant pessimism of the 1980s was very much alive during the early months of 1987 when the theme of this symposium was formalized. Indices of real metal prices had only inched-up from all-time lows in 1986. The hemorrhage of corporate red-ink was still a powerful memory. Frustration with the apparent inability of closures and reduced capacity utilization to re-establish market balance was strong. To the more pessimistic, the industry appeared destined to a quarter century of persistent excess capacity and nonremunerative prices. The conditions to support this pessimism were readily apparent. Economic literature tells us that surplus capacity is a complex, usually unexpected and often long-lived phenomenon caused by the interaction of at least three factors. The first is a rising capital-intensity of production. The second is the presence of aggressive new entrants whose capacity additions are typically (1) trade- dedicated because local market absorption is low; (2) cost-competitive for natural or policy-support reasons; (3) heavily burdened by debt-repayment obligations; and (4) viewed as important sources of employment, regional development and foreign exchange. The third, and often decisive, factor is an unanticipated decline or stagnation in demand growth for the sector's output. The first two factors combine to increase competitive pressures and to raise the actual or perceived cost of idle capacity. Market rigidity reduces responsiveness to price signals and distorts the burden of adjustment. Demand atrophy exacerbates these pressures especially on unprotected producers in the higher quadrants of the global supply function. In the mid-1980s, evidence of the existence of all these factors were easy to cite. Culprits were often identified. Claims for protection, global sharing of adjustment burdens, and imposition of disincentives to new capacity regardless of inherent economic status were co-dominant themes with the buzz-words of "competitiveness" and "level playing fields." This, notwithstanding the suggestions of the same economic literature that excess capacity persists longest when interventionist remedies permit it to continue. Today, only eighteen months later, the mood is decidedly more buoyant and most analysts are cautiously optimistic about the next few years. Many informed analysts have concluded that the excess capacity of the recent past has disappeared. For the present, the marketplace seems to have restored a balance between supply and demand. That the adjustment took five or six years longer than anticipated attests to the dramatic structural changes which have characterized the industry. The implications of these changes for the future are unclear. Were the macroeconomic shocks, coupled with industry transitions, so extraordinary in magnitude and timing that experiences were unique? If so, the next years may hold more stable and cautious times for the industry. Alternatively, is the inherently volatile metals industry facing a future of cycles equally perverse in terms of amplitude and duration due to economic uncertainities and inflexible industry response capabilities?

Jan 1, 1989

By G. J. C. Young

The paper describes the replacement of a conventional filtration, clarification and zinc precipitation plant by a carbon in pulp (CIP) electrowinning plant, with the objective of improving the recovery of gold from cyanide leached, acid plant calcines. The discussion covers the early laboratory studies to the design and erection of the full scale plant. Particular emphasis is placed on the problems encountered with commissioning and the strategies which were employed to solve them.

Jan 1, 1982

By Michael Edesess

The salt gradient solar pond has been the focal point of accelerating international attention and interest in recent months. Only recently have most investigators in the renewable energy field come to realize the versatility of the solar pond, and its ability to overcome certain problems usually associated with solar technologies. These realizations, together with clear demonstrations in Israel and elsewhere of its technical feasibility, have combined to bring the solar pond to the forefront of renewable energy technologies. The solar pond is a natural or site-built pond, about one to five meters or more in depth, which has been altered to retard the loss of absorbed solar energy. The absorbed solar energy is usually lost through upward buoyancy of the warmed water, followed by the loss of its heat to the atmosphere. The chief solar pond technology -the salt gradient, or "nonconvective" solar pond-prevents this upward buoyancy by means of a vertical density gradient achieved with dissolved salt. The deep waters in the solar pond reach high temperatures, up to and even above the boiling point of pure water.

Jan 1, 1981

The 1996 Arizona Conference was held in Tucson on Dec. 8 and 9. Attendance was 648, a 12% increase from the 1995 conference. The annual conference is organized by the Arizona Conference Board of Directors, representing SME sections from throughout Arizona and adjacent areas. In addition to those representing mining and processing operations in the Arizona region, the meeting was well attended by interested parties from throughout North America. These included vendors, consultants, academia, research organizations and corporate management. The technical program highlighted the meeting. It consisted of a keynote address and morning and afternoon technical sessions. In the technical sessions, 23 papers were presented by the mining, hydrometallurgical, smelting, geology and mineral-processing divisions. The conference was then capped by a banquet that included a talk by a noted economist. Keynote address The program was kicked off by a keynote address titled "Forecasting for the 105th Congress," by Rep. John Shadegg (R-AZ). He was elected to Arizona's Fourth Congressional District in 1994. Shadegg serves on the House Budget Committee, the Resources Committee and the watchdog Government Reform Committee. He stressed the familiar conservative positions of reducing government spending, balancing the budget and states rights. As a member of the House Resources Committee, Shadegg stated his support for the mining industry. Technical sessions Mining division. Two of the five presentations described developments at two Arizona mining operations. T.J. Swendseid of Phelps Dodge presented a paper titled "New developments at Morenci" and P. Garretson of BHP presented a paper titled "Startup of the Robinson Project." Morenci continues to expand its operation and recently broke records for production. Other developments at Morenci included the completion of a 600-m (2,000-ft) drainage tunnel and stockpile rehandling. In addition, Phelps Dodge moved Morenci's crusher plant. It was completely disassembled and reassembled in just eight days. Another interesting presentation was "Predictive maintenance techniques for large electric shovels at Cyprus Sierrita," presented by T. Ritzel of Cyprus Amax. The presentation described high-technology methods for predicting maintenance problems. These methods included vibration analysis, ultrasonic detection, infrared thermography, electrical measurements and tribology (the science of lubricant evaluation). The benefits of these techniques are reduced downtime of the equipment, as was demonstrated in case studies at the mine. The other presentations were "Introduction to NOSA 5-star safety program," by R. McKinnon, BHP Copper North America, and "A new design guideline for mine sealing," by K. Fuenkajorn, Rock Engineering International. Hydrometallurgical division. The hydrometallurgical session consisted of five papers. These included a presentation titled "Recovery of gold and silver using guanidine-based extractants," by M. Vining of Henkel Corp., Tucson, AZ. In this presentation, guanidine-based extractants LIX-79 and AURIX resin were introduced. LIX-79 was shown to have applications in copper-gold and high silver ores. In ammonia-cyanide leaching, AURIX was shown to be more selective in CIL vs. RIL comparisons. Other papers in the hydrometallurgical division included "Application of cobalt in the copper industry," by J. Hawke, OMG Apex Inc.; "Series parallel conversions and production gains at Cyprus Miami Mining's dump leach and solvent extraction operation," by E. Bilson of Cyprus Amax; "Lead alloy anode corrosion at the San Manuel SXEW tankhouse," by W .M. Gort of BHP Copper and "Hydrometallurgical treatment of copper refinery slimes," by B.C. Wesstrom of Phelps Dodge. Smelting division. Three papers were presented in the smelting division session. These included updates and reports on improvements at the Hayden, Hidalgo and BHP San Manuel smelters. For example, W.A. Dutton of Phelps Dodge presented "Recent improvements at the Hidalgo Smelter." These changes were aimed at reducing environmental emissions and increasing production. They included modifications to the fugitive-gas collection system to reduce particulate emissions, rubber lining the acid plant scrubbers to reduce corrosion and the installation of a cold lime softening system for water treatment. Equally interesting papers were presented by D. Norton of Asarco, Hayden, AZ, in a paper titled "Update of the Hayden smelter process," and by D. Jones of BHP Copper, San Manuel, AZ, in a paper titled "Update on first campaign of the BHP San Manuel Copper." Geology division. The session began with a paper that outlined the progress of an exploration project in South America. "The Pierina exploration project, Ancash Province, Peru" was presented by J.D. Lowell, Lowell Mineral Exploration, Rio Rico, AZ. Another paper was then presented on a copper deposit in Grant County, New Mexico. "Zonation of supergene copper minerals at Hanover Mountain, Grant

Jan 1, 1997

By Samer Sadek, Phoebe Cheng, Changmo Kwon, Myat Ohn

BART Facilities Standards (BFS) Structural Criteria is a living document that governs planning, design, and construction of all BART projects. Since its development, the document undergoes incremental changes and updates to reflect policy changes, changes in local, State, or national design codes and guidelines, advancements in engineering and technology, or based on the performance of past built infrastructure. In 2020, the BFS-Structural Criteria underwent a comprehensive update and was released with BFS version 3.2. This paper summarizes the updates to the Tunnels and Underground Structures Section of the Structural Criteria, and provides insights to the basis and logic of the requirements.

Dec 1, 2022

By CLAIRE STREBINGER, ADITYA JUGANDA, JURGEN F. BRUNE, GREGORY E. BOGIN JR.

Methane gas explosions are a major risk in underground coal mining operations. The severity of such explosions can range from local area damage to massive loss of miners’ lives along with significant damage to mine infrastructure and ventilation controls that may lead to mine closure and loss of the entire operation. This study demonstrates the viability of integrating a computational fluid dynamics (CFD) combustion model into a longwall mine ventilation model to simulate methane gas explosions in the longwall face area. The resulting 3D methane gas explosion simulation can provide better understanding of the fundamental physics and the potential impact of an explosion in an underground longwall coal mine.

Aug 1, 2022

By Lyle W. Talbotr

The DeLamar Silver Mine is a Joint Venture between Earth Resources Company, the Canadian Superior Mining Company and the Superior Oil Company. The property is a consolidation of several old operations in the district. The more widely known are the DeLamar and Sommercamp Mines. The location is 20 miles northeast of Jordan Valley, Oregon and 55 miles southwest of Boise, Idaho. The mine is on the south slope of DeLamar Mountain in the Owyhee Mountains of southwest Idaho Initial interest started in 1969 with serious exploration beginning in 1970. The feasibility study was completed in 1974, and in 1975 Mountain States Engineers were retained to design and build the plant. Processing of ore began in March of 1977 with the first bullion poured in April of that year. The plant is currently processing some 2200 TPD of ore with a grade of four ounces of silver and 0.03 oz. of gold per ton of ore. Cyanide consumption is 2.5 lb/ton, zinc consumption of 0.3 lb/ton and flocculent consumption of 0.5 lb/ton. A flowsheet is shown as Figure I. The grinding circuit is of two stage design. The primary mill is an 18 ft. dia. by 9 ft. long semi-autogenous unit. The secondary mill is a 9 1/2 ft. dia. by 15 ft. long overflow ball mill. The mill discharges are combined and sent to 15 in. cyclones for classification. Cyclone overflow reports to leaching with the underflows reporting to the ball mill. The cyclone feed pump is an 8X6 metal case pump. The primary mill has 1000 installed horsepower and rotates at 68% of critical speed. The ball mill has 700 installed horsepower and rotates at 72% of critical speed. Because the primary mill is horsepower limited the ball charge is varied to maintain the desired throughput. The mill power is held at 980-990 HP by modifying the feed rate. Four inch forged steel balls are added any time the ore feed fails to reach 100 tons per hour for four hours. During periods of extremely hard ore, the ball charge has been as high as 14 v/o and at other times the mill has operated fully autogenous for weeks.

Jan 1, 1980

By S. M. Hossaini, M. Ataei, H. Moosavi

The abstract highlights the importance of pillar stability in underground coal mines and the influence of rock mass strength and joint orientation on pillar behavior. The study employs numerical modeling using the distinct element code (UDEC) to investigate the impact of these factors on pillar stability. The research considers different joint orientations and varying rock mass strengths, analyzing parameters like stress distribution, displacement, and failure patterns. The findings reveal that both joint orientation and rock mass strength significantly affect pillar stability, with specific combinations leading to reduced safety factors and increased deformation. The study concludes by emphasizing the importance of considering these factors in pillar design for safe and efficient mining operations.

Apr 4, 2022

By L. E. Sausa

Measuring the specific gravity of a pulp in concentrating plants is a relative, y simple procedure, but the desired accuracy is often difficult to attain. Many plants use the system of weighing a known volume of the pulp on a scale. In many cases, this method is quite accurate, but obtaining a true sample presents quite a problem. This is especially true when the pulp tends to froth, the solids settle rapidly, or the flow is fast at the point of sampling. There is also the problem of the operator neglecting to take the sample because of duties elsewhere, or, if everything Is apparently running smoothly, he assumes the pulp density is also all right. In 1952, the Pine Creek plant of Union Carbide Nuclear Company began working on a better method for measuring and controlling pulp density. After an extensive investigation of different methods for measuring the specific gravity of moving pulps, the Research Department decided that the bubble tube method appeared to be the simplest and most promising for our applications. It consists of two bubble tubes, of different lengths, submersed in a pulp. Low pressure air is supplied to, the two tubes through sight bubblers to maintain approximately equal volume of air to each bubble tube. The bubble tubes are also connected to a differential manometer, one to each side. Therefore, knowing the vertical distance between the outlets of the bubble tubes, the manometere can be calibrated to measure directly the specific gravity of the pulp. (Figure No. 1 illustrates this model.)

Jan 1, 1960

By Zachary D. Jones

"Construction projects involve a great many risks. The risk that material prices will increase during construction or that the work under construction will be destroyed by fire, storm or some other act of God are just a few examples. In tunneling or other underground projects, one of the most significant risks is that the subsurface conditions encountered during construction will differ from what is expected. Each of these risks must be accounted for, managed and, ultimately, the duty of one party or the other to bear. The primary tool used to allocate the risks among the parties is the construction contract.How construction contracts allocate the risk that subsurface conditions will differ have changed substantially over the past century. Today, construction contracts typically allocate the risk through a series of provisions. The first is the differing site condition or changed condition clause. That clause, when included, typically provides that the owner bears the risk that the subsurface conditions will differ from what is indicated in the contract documents or what is reasonably expected. The second clause is one that provides that the contractor must conduct a reasonable site investigation and bear the risk of any conditions that such an investigation would reveal. The third provision includes disclaimers that are often included in geotechnical data provided by the owner (or the owner’s engineer) to the contractor which attempts to limit the information on which the contractor can rely. Because these risk-allocating devices seem to be somewhat conflicting, a brief discussion of each provides critical insight in understanding how the modern construction contract allocates the risk of differing site conditions.At the start of the 20th century, construction contracts looked substantially different than they do today. For example, one contract for the construction of a public water tunnel in Chicago, IL, drafted around 1895 contained the following clause:The contractor must take the work entirely at his own risk. No extra allowance will be made for quicksand, hardpan or boulders."

Jan 1, 2014

By Louis M. Perlman

Quantitative methods are, by now, a standard tool of the mining industry, and are commonly used by Research Departments in their evaluation of production methods and schedules, and their associated costs. Indeed, much sophisticated computer work has been devoted to such evaluation of controllable costs and capital requirements. These data are an important input into the project evaluation formula, which is probably the most important single calculation per formed by a mining company, since the result decides whether a particular project is viable. It is instructive to summarize the broad principles of project evaluation, since they are crucial to the remaining sections of this paper. PROJECT EVALUATION The most widely used method of appraising projects is known as Discounted Cash Flow (DCF) method. Two main variants are used; they are known as the 'not present value' (NPV) approach and the 'internal rate of return' (IRR) approach respectively. The difference between the two is that the former takes the firm's interest rate as given and uses this knowledge to calculate the present value of the project; whereas the latter calculates the highest interest rate the project could tolerate and still just breaks even. The technique is more simply discussed in terms of the first method (NPV).

Jan 1, 1972

By E. J. Hammer

In the crushing and grinding of metallics for beneficiation, the sizing is normally done to liberate the metals or sulphides for further processing to improve recoveries of the basic metals or minerals. The objective is to reduce the ore in size through various closely controlled stages to that degree of fineness which gives an economic liberation of valuable mineral, but which avoids as much as possible the production of sliming fractions. A different philosophy applies to the crushing and grinding of Gypsum. Our requirements normally demand controlled grinding and/or crushing of the material not only to a fineness suitable for further processing of the mineral into end products, but to produce various sizes of material which are them- selves saleable products. The majority of our tonnage ultimately ends up in stucco for Wallboard. Therefore, our mineral reduction is normally designed toward this end, but it is done in a manner that permits drawing off inter- mediate products to meet various Customer requirements. This forces us into compromises at times in our equipment installations, and our equipment must sometimes be more versatile and complex than we would like it to be. We try to process our basic rock, Gypsum, for the most efficient size reduction. We market 5 to 6 different sizes intermediate to the end product, which generally is the fineness of material to be used for stucco for Wallboard, and we do this with controlled crushing, grinding and sizing cycles of the material. To summarize, we use a different philosophy of crushing and grinding than the metallic field which uses comminution or crushing and grinding to improve recovery, whereas we choose our equipment to crush and grind primarily for product performance.

Jan 1, 1969

By Steve Kral

The former mayor of Los Angeles, CA is a believer in public transportation but thinks neither his city nor the entire country is spending enough on basic infrastructure. In fact, the United States has fallen behind most other developed nations in improving public transportation, the former mayor said. Antonio R. Villaraigosa was the keynote speaker at the North American Tunneling (NAT) conference, held June 22-25 in Los Angeles, CA. The event, held every two years, is sponsored by the Underground Construction Association of SME (UCA). This years? conference attracted 1,091 underground construction professionals from around the world. The accompanying exhibition continues to grow, attracting 142 exhibiting companies occupying 162 booths. As always at NAT, registered attendees received the proceedings volume of the conference, which contains 132 papers. The proceedings volume, including a CD of the papers, is available from SME for $149 member, $139 student member and $189 nonmember. The book can be ordered from SME, NAT item #400-4, phone 303-948-4225, 1-800-763-3132, or online at www.smenet.org/store.

By Gill Montgomery

Although fluorspar is considered an industrial mineral by usage and value, its geological occurrence and the mining and milling methods employed make it more akin to the non-ferrous metal ores. Likewise methods of exploration for it are more like those used in the search for lead and zinc, with which fluorspar is often mixed. In fact, it often takes the mixture of fluorspar, lead, zinc, plus maybe barite to add up to enough recoverable values to make the mineral an ore by definition. This is so true where the fluorspar portion is low grade, perhaps less than 25 percent. Until the development of modern steel milling in World War I times, the invention of aluminum smelting, and development of the fluorine chemical industry and air conditioning, there were few uses for fluorspar aside from ceramic fluxes in the flint glass industry and for uses as glazes for pottery and china. Pure fluorite crystals have long been admired as semi-precious and ornamental minerals of many delicate colors.

Jan 1, 1983

By David E. Sims

Asarco has been using computer-aided open-pit mine design since 1966. The in-house developed program package includes drill-hole analysis programs, interpolation routines, and three-dimensional open-pit design programs. The financial analysis step after pit design required that a reasonably accurate schedule be produced so that a good cash flow model could assess the feasibility of a project. The manual method of scheduling was too time-consuming for feasibility work, so a computerized scheduler was required. Since no computerized mine scheduling programs existed, we requested proposals from consulting firms to develop such a program. The selection of a consulting firm, the formulation of the contract and design specifications required about three years to accomplish. The consulting firm, Systems Control Inc. (SCI), of Palo Alto, spent over one year doing the programming and testing alone. The details of the program development were reported in "Computerized Year-by-Year Open-Pit Mine Scheduling," SME-AIME Transactions, December 1974. In June of 1973 the program, which SCI dubbed Optimum Resource Extraction or ORE, was installed. Version 1 of ORE was utilized successfully on three separate properties over a period of two years. During this time it became obvious that some of the original design specifications were restrictive, and certain modifications were required. The ORE program was submitted for modification, and after one year version 2 was operational in May of 1976. The program now consists of approximately 20,000 lines of FORTRAN source statements grouped into 190 subprograms, and runs in a 450K region of Asarco's 370/148 in Cranford, NJ. The Tucson com¬puter (370/115) is tied to the Cranford computer via a 9600 baud leased T.P. line, for running mine scheduling and other large mine planning programs.

Jan 1, 1979

By P. C. Thakur

Mine productivity, measured by the output of minerals per manshift, depends on a number of factors including physical conditions of the minable seam, type of mining equipment, management techniques, worker attitudes and governing jaws and regulations. The greatest scope of improving productivity lies, perhaps, in modifying physical conditions to an advantage and using highly productive equipment. In the case of coal mines, increased productivity can be achieved by (i) obtaining prior knowledge of the mineable property, e.g., the grade and thickness of, the coal seam, presence of sand channels, faults, etc., (ii) eliminating conditions that hamper production, e.g., high emissions of methane and water, and (iii) using more productive mining techniques. Conoco/Consol's (Conoco Inc. and Consolidation! bal Company, a fully-owned subsidiary) horizontal drilling system was developed with the hove objectives in mind. It can drill 75 to 1001 in diameter boreholes to depths of more than 600 1 and maintain the borehole in a preselected horizon. Such boreholes can be utilized for premining exploration of the coal seam, for removing methane and water and in devising mining techniques with high productivity. The purpose of this paper is to describe the horizontal drilling system briefly and to discuss its applications in the above-mentioned- areas.

Jan 1, 1980

By William R. Groseclose, Kenneth D. Schoeman

The Buckskin Mountains Tunnel is a key link in the Bureau of Reclamation's Central Arizona Project. The 22-foot (6.7-m) diameter tunnel is being bored in a north-northwesterly direction through volcanic rock near Lake Havasu in western Arizona. The 6.9-mile (11-km) conveyance tunnel will carry up to 3,000 cfs (85 cu m per sec) of water through the Buckskin Mountains as part of the Granite Reef Aqueduct. The water for the project will be drawn from Lake Havasu behind Parker Dam on the Colorado River and pumped some 800 feet (244 m) above the lake to the inlet portal of the free flow tunnel where it begins its 190-mile (300-km) journey to Phoenix, Arizona, and beyond into Orme Reservoir (figure 1). Precast concrete segments are being used as a single system initial support and final lining in the tunnel being excavated by a tunnel boring machine specially designed and built for the job by The Robbins Company. J. F. Shea Company, Inc., of Walnut, California, is constructing the tunnel for the Bureau of Reclamation.

Jan 1, 1976